Crystal Growth and Characterization of Li0.9Mo6O17

Purple bronze Li0.9Mo6O17 has attracted researchers for its low dimensionality and corresponding properties. Although it has been studied for nearly two decades, there are still some unsolved puzzles with this unique material. Single crystals of Li0.9Mo6O17 were grown using the temperature gradient flux technique in this research. The crystal growth was optimized by experimenting different conditions and good quality crystals were obtained. X-ray diffraction results have confirmed the right phase of the crystals. Resistivity measurements and magnetic susceptibility measurements were carried out, and anomalous electronic behaviors were found. All of the samples showed the metal-insulator transition near 20K, followed by behavior that differs from sample to sample: either superconducting, metallic or insulating behavior was observed below 2K. Li0.9Mo6O17 was considered as a quasi-one-dimensional crystal and also a superconducting crystal, which implies a dimensional crossover may occur at the metal-insulator transition. A two-band scenario of the Luttinger liquid model was used to fit the resistivity data and excellent results were achieved, suggesting that the Luttinger theory is a very good candidate for the explanation of the anomalous behavior of Li0.9Mo6O17. In addition, the susceptibility measurements showed Curie paramagnetism and some temperature independent paramagnetism at low temperature. The absence of any anomalous magnetic feature near 20K where the resistivity upturn takes place, suggests that a charge density wave mechanism, which has been proposed by some researchers, is not responsible for the unique properties of Li0.9Mo6O17.

Molecular Magnetism: The Design, Synthesis, and Characterization of New Building Blocks for Molecule-based Magnetic Materials

Two classes of building blocks have been prepared and characterized and their coordination chemistry explored working towards the preparation of new molecule-based magnetic materials. In the first project, the amine functionality of 3,3'-diamino-2,2'- bipyridine was exploited for the preparation of a new family of ligands (H2L 1)-(H2L 4). The molecular structures of three ligands have been fully characterized by X-ray crystallography. [molecular structure diagram will not copy here, but is available in full pdf.] The coordination chemistry of these ligands with divalent first row transition metal ions was investigated. For ligand (H2L1), the molecular structures of four coordination complexes with stoichiometries [Zn2(Ll)(OAc)(MeO)]2 (I), [Cu2(L1)(OAc)2 (II), [Li(L1)]3 (III), and [Ni(L1)]3 (IV) were determined by X-ray crystallography. For ligand (H2L2), a Cu(II) complex of stoichiometry [Cu3(L2)(OAc)3MeO] (V) was determined by X-ray crystallography. The magnetic properties of complexes (II), (III), and (V) have been fully elucidated. In project two, synthetic strategies for the preparation of porphyrin molecules bearing triol substituents is presented. Following this approach, three new porphyrin derivatives have been prepared and characterized [Zn(HPTPP-CH2C(CH20H)3)] (VI), [P(TPP)(OCH2C(CH2)H)3)2]+CL- (VII), and [P(OEP)(C6H5)(OCH2C(CH2OH)3)]+Cl- (VIII). Attempts to exchange the labile methoxide bridges of a tetraironIIl single molecule magnet of stoichiometry [Fe4(OMe)6(dpm)6] (Hdpm = dipivaloylmethane) with the triol appended porphyrins will be discussed. [molecular structure diagram will not copy here, but is available in full pdf.]

High-Spin and Emissive Molecular Materials: Synthesis and Characterization of New Polynuclear Ni(II) Complexes from the Use of Aromatic Schiff Bases as Bridging Ligands

The employment of the bridging/chelating Schiff bases, N-salicylidene-4-methyl-o-aminophenol (samphH2) and N-naphthalidene-2-amino-5-chlorobenzoic acid (nacbH2), in nickel cluster chemistry has afforded eight polynuclear Ni(II) complexes with new structural motifs, interesting magnetic and optical properties, and unexpected organic ligand transformations. In the present thesis, Chapter 1 deals with all the fundamental aspects of polynuclear metal complexes, molecular magnetism and optics, while research results are reported in Chapters 2 and 3. In the first project (Chapter 2), I investigated the coordination chemistry of the organic chelating/bridging ligand, N-salicylidene-4-methyl-o-aminophenol (samphH2). The general NiII/tBuCO2-/samphH2 reaction system afforded two new tetranuclear NiII clusters, namely [Ni4(samph)4(EtOH)4] (1) and [Ni4(samph)4(DMF)2] (2), with different structural motifs. Complex 1 possessed a cubane core while in complex 2 the four NiII ions were located at the four vertices of a defective dicubane. The nature of the organic solvent was found to be of pivotal importance, leading to compounds with the same nuclearity, but different structural topologies and magnetic properties. The second project, the results of which are summarized in Chapter 3, included the systematic study of a new optically-active Schiff base ligand, N-naphthalidene-2-amino-5-chlorobenzoic acid (nacbH2), in NiII cluster chemistry. Various reactions between NiX2 (X- = inorganic anions) and nacbH2 were performed under basic conditions to yield six new polynuclear NiII complexes, namely (NHEt3)[Ni12(nacb)12(H2O)4](ClO4) (3), (NHEt3)2[Ni5(nacb)4(L)(LH)2(MeOH)] (4), [Ni5(OH)2(nacb)4(DMF)4] (5), [Ni5(OMe)Cl(nacb)4(MeOH)3(MeCN)] (6), (NHEt3)2[Ni6(OH)2(nacb)6(H2O)4] (7), and [Ni6(nacb)6(H2O)3(MeOH)6] (8). The nature of the solvent, the inorganic anion, X-, and the organic base were all found to be of critical importance, leading to products with different structural topologies and nuclearities (i.e., {Ni5}, {Ni6} and {Ni12}). Magnetic studies on all synthesized complexes revealed an overall ferromagnetic behavior for complexes 4 and 8, with the remaining complexes being dominated by antiferromagnetic exchange interactions. In order to assess the optical efficiency of the organic ligand when bound to the metal centers, photoluminescence studies were performed on all synthesized compounds. Complexes 4 and 5 show strong emission in the visible region of the electromagnetic spectrum. Finally, the ligand nacbH2 allowed for some unexpected organic transformations to occur; for instance, the pentanuclear compound 5 comprises both nacb2- groups and a new organic chelate, namely the anion of 5-chloro-2-[(3-hydroxy-4-oxo-1,4-dihydronaphthalen-1-yl)amino]benzoic acid. In the last section of this thesis, an attempt to compare the NiII cluster chemistry of the N-naphthalidene-2-amino-5-chlorobenzoic acid ligand with that of the structurally similar but less bulky, N-salicylidene-2-amino-5-chlorobenzoic acid (sacbH2), was made.

Synthesis, properties and characterization of N-Alkyl substituted b-Diketiminato copper(I) Complexes

Le ligand nacnacxylH (xyl = C6Me2H3) et les ligands dikétimines N-alkyle substitués (nacnacCH(Me)PhH, nacnacBnH and nacnaciPrH) ont été préparés avec de bons rendements à l’exception du nacnaciPrH (23%) en utilisant un protocole en une étape et à l’aide d’un montage Dean-Stark. La réaction du S,S-nacnacCH(Me)PhH et du nacnacBnH avec le nBuLi dans le THF conduit au S,S-nacnacCH(Me)PhLi(THF) et au nacnacBnLi(THF). Les tentatives de bromation de ces composés par le N-bromosuccinimide conduisent plutôt aux ligands S,S-succnacnacCH(Me)PhH et succnacnacBnH (succ = succinimido) substitués par un groupement succinimido sur le carbone  La chloration par le N-chlorosuccinimide conduit au produit désiré, mais avec des impuretés. La réaction de ces ligands avec le CuOtBu (ou bien MesCu, où Mes = C6Me3H2, et une quantité catalytique de CuOtBu) en présence de bases de Lewis donne les (nacnacxylCu)2(-toluène), nacnacxylCuCNC6H3(Me)2, nacnacCH(Me)PhCuL (L = PPh3, PMe3, CNC6H3(Me)2, DMAP, lutidine, Py, MeCN), nacnacBnCuL (L = PPh3, CNC6H3(Me)2, styrène, trans-stilbene, phenylvinylether, acrylonitrile, diphenylacetylène), nacnaciPrCuL (L = PPh3, CNC6H3(Me)2, MeCN) et le succnacnacCH(Me)PhCuL (PPh3, CNC6H3(Me)2, pyridine). Tous ces complexes sont jaunes et sensibles à l’air et à l’humidité. En l’absence de fortes bases de Lewis, on n’observe pas de réaction entre les précurseurs de cuivre et les ligands N-alkyle substitués. Les études RMN des complexes dans le C6D6 ne présentent pas de complexe de toluène mais un mélange à l’équilibre du (nacnacxylCu)2(-C6D6) et nacnacxylCu(C6D6) dans une proportion de 2 pour 1. Alors que l’addition de plus de cinquante équivalents soit de THF, soit de toluène n’induit aucun changement des spectres RMN, l’addition de 2 équivalents de MeCN conduit instantanément au complexe nacnacxylCu(MeCN). De plus, le (nacnacxylylCu)2(-C6D6) ne se coordone ni ne réagit avec le N2O, même après avoir été chauffé à 60°C pendant treize jours. En présence de DPA (diphenylacétylène), la réaction du nacnacBnH avec le CuOtBu conduit au dimère ponté (nacnacBnCu)2(µ-DPA). L’addition d’un excès de DPA (10-12 équivalents) transforme le dimère ponté en complexe lié en position terminale nacnacBnCuDPA. Les nacnacRH (R = CH(Me)Ph et i-Pr) ne forment pas de complexe ni avec les oléfines ni avec le DPA. Une réactivité similaire a été observée avec les complexes de nacnacCH(Me)PhCu(NCMe) et nacnaci-PrCu(NCMe). Tandis que le complexe lié en position terminale par MeCN a été isolé et caractérisé, l’équilibre en solution nous laisse suspecter la formation d’un complexe d’acétonitrile ponté. Des études de réactivité comparatives ont été menées sur quelques complexes de cuivre. La Morpholine ne réagit pas avec le nacnacBnCu(acrylonitrile) contrairement à l’acrylonitrile libre. L’expérience de l’échange d’oléfine montre que l’acrylonitrile (une oléfine électro-attractrice) se lie plus fortement que les autres oléfines, mettant ainsi en évidence l’importance de la rétrodonation  face à la donation La rétrodonation est cependant faible comparée aux autres complexes de styrène structurellement caractérisés. Les complexes nacnacCH(Me)PhCuL (L = PPh3 et MeCN) ont été employés dans la cyclopropanation catalytique du styrène et dans l’addition conjuguée du ZnEt2 sur la 2-cyclohexénone, mais les résultats indiquent que le ligand dikétimine est éliminé avant son entrée dans le cycle catalytique. Par conséquent, il n’y a pas d’induction chirale. Les complexes tétra coordinées de cuivre avec les nacnacRCu(phen) (R = Bn, CH(Me)Ph et Phen = 1,10-phenanthroline, 2-Mes-1,10-phenanthroline, 2,9-dimethyl-1,10-phenanthroline (dmp) et 2,9-diphenyl-1,10-phenanthroline (dpp)) ont été synthétisés. Ces complexes sont d’une intense couleur bleue et des interactions d’empilement entre l’un des cycles phényle des ligands nacnac et la phénanthroline ont été observées dans les structures à l’état solide. Les mesures en absorption UV-visible ont été effectuées dans le toluène et les bandes MLCT sont déplacées vers le rouge par rapport à celles des complexes de cuivre et bisphénanthroline. Tous ces composés émettent à l’état solide mais les complexes 1,10-phenanthroline et 2-Mes-1,10-phenanthroline n’émettent pas en solution. Pour renforcer les interactions d’empilement , les nouveaux ligands nacnacRH (R = CH2C6H2(OMe)3, CH2C6F5) et leurs complexes de cuivre respectifs ont été préparés avec du dmp et dpp. Afin de permettre la comparaison, le nacnaciBuCu(dmp) a été synthétisé. Alors que les complexes dmp montrent une augmentation des interactions intramoléculaires - avec les substituants phényle du ligand dikétimine et de la phénanthroline, les complexes dpp ne révèlent pas de telles interactions. Les complexes perfluorés montrent, en absorption et en émission, un déplacement significatif vers le bleu, alors que les complexes substitués par un groupements isobutyle présentent des transitions déplacées vers le rouge. Alors que les intensités de luminescence et les durées de vie sont faibles, les déplacements réduits de Stokes et les pics étroits de luminescence comparables indiquent une réduction des distorsions de l’état excité.

Synthesis of polyelectrolyte brushes on silica-based substrates through surface-initiated polymerization : brush characterization and responsiveness to variation in pH and ionic strength

Les brosses de polyélectrolytes font l’objet d’une attention particulière pour de nombreuses applications car elles présentent la capacité de changer de conformation et, par conséquent, de propriétés de surface en réponse aux conditions environnementales appliquées. Le contrôle des principaux paramètres de ces brosses telles que l'épaisseur, la composition et l'architecture macromoléculaire, est essentiel pour obtenir des polymères greffés bien définis. Ceci est possible avec la Polymérisation Radicalaire par Transfert d’Atomes - Initiée à partir de la Surface (PRTA-IS), qui permet la synthèse de brosses polymériques de manière contrôlée à partir d’une couche d'amorceurs immobilisés de manière covalente sur une surface. Le premier exemple d’une synthèse directe de brosses de poly(acide acrylique) (PAA) par polymérisation radicalaire dans l’eau a été démontré. Par greffage d’un marqueur fluorescent aux brosses de PAA et via l’utilisation de la microscopie de fluorescence par réflexion totale interne, le dégreffage du PAA en temps réel a pu être investigué. Des conditions environnementales de pH ≥ 9,5 en présence de sel, se sont avérées critiques pour la stabilité de la liaison substrat-amorceur, conduisant au dégreffage du polymère. Afin de protéger de l’hydrolyse cette liaison substrat-amorceur sensible et prévenir le dégreffage non souhaité du polymère, un espaceur hydrophobique de polystyrène (PS) a été inséré entre l'amorceur et le bloc de PAA stimuli-répondant. Les brosses de PS-PAA obtenues étaient stables pour des conditions extrêmes de pH et de force ionique. La réponse de ces brosses de copolymère bloc a été étudiée in situ par ellipsométrie, et le changement réversible de conformation collapsée à étirée, induit par les variations de pH a été démontré. De plus, des différences de conformation provenant des interactions du bloc de PAA avec des ions métalliques de valence variable ont été obtenues. Le copolymère bloc étudié semble donc prometteur pour la conception de matériaux répondant rapidement a divers stimuli. Par la suite, il a été démontré qu’un acide phosphonique pouvait être employé en tant qu’ amorceur PRTA-IS comme alternative aux organosilanes. Cet amorceur phosphonate a été greffé pour la première fois avec succès sur des substrats de silice et une PRTA-IS en milieux aqueux a permis la synthèse de brosses de PAA et de poly(sulfopropyl méthacrylate). La résistance accrue à l’hydrolyse de la liaison Sisubstrat-O- Pamorceur a été confirmée pour une large gamme de pH 7,5 à 10,5 et a permis l’étude des propriétés de friction des brosses de PAA sous différentes conditions expérimentales par mesure de forces de surface. Malgré la stabilité des brosses de PAA à haute charge appliquée, les études des propriétés de friction ne révèlent pas de changement significatif du coefficient de friction en fonction du pH et de la force ionique.

Zeolite Encapsulated Complexes Of Fe,Co,Ni,Cu And Pd:Synthesis , Characterization And Catalysis-2003

This thesis deals with the synthesis, characterization and catalysis activity studies of some zeolite encapsulated complexes. Encapsulation inside the zeolite cages makes the catalysts more stable. Further, the framework prevents the complexes from dimerising. Catalysis by metal complexes encapsulated in the cavities of zeolites and other molecular sieves has many features of homogeneous, heterogenous and enzymatic catalysis. Serious attempts has been made to gain product selectivity in catalysis .The catalytic activity shown by the encapsulated complexes can be correlated to the structure of the active site inside the zeolite pore. It deals with the studies on the partial oxidation of benzyl alcohol to benzaldehyde. The oxidatio was carried out using hydrogen peroxide as oxidant in presence of PdYDMG and CuYSPP as catalysts. The product (benzaldehyde) was detected using TLC and confirmed using GC.The catalytic activity of the complexes was tested for oxidation under various conditions. The operating conditions like the amount of the catalyst, reaction time, oxidant to substrate ratio, reaction temprature, and solvents have been optimized. No further oxidation products were obtained on continuing the reaction for four hours beyond the optimum time. Maximum conversion was obtained at room temperature and the percentage conversion decreased with increase in temperature. Activity was found to be dependent on the solvent used. With increasing awareness about the dangers of environmental degradation, research in chemistry is getting increasing geared to the development of “green chemistry,” by designing environmentally friendly products and processes that bring down the generation and use of hazardous substances.

Electro-Optical Properties of Metal Phthalocyanines and Naphthalocyanines

The thesis deals with the preparation of chemical, optical, thermal and electrical characterization of five compounds, namely metal free naphthalocyanine, vanadyl napthalocyanine, zinc naphlocyanine, europium dinaphthalocyanine, and europium diphthalocyanine in the pristine and iodine-doped forms. Two important technological properties of these compounds have been investigated. The electrical properties are important in applications sensors and semiconductor lasers. Opto-thermal properties assume significance for optical imaging and data recording. The electrical properties were investigated by dc and ac techniques. This work has revealed some novel information on the conduction mechanism in five macrocyclic compounds and their iodine-doped forms. Also useful data on the thermal diffusivity of the target compounds have been obtained by optical techniques.

Studies on Catalysis by Vanadia Supported On Metal Oxides

Catalysis is an essential technology in manufacturing industries. The investigation based on supported vanadia catalysts and it’s sulfated analogues. Vanadia is a transition metal oxide and is used in oxidation reactions in chemical industry. It is more active and selective catalysts on suitable supports. The work deals with preparation of vanadia incorporated tin oxide and zirconia systems by wet impregnation. Physico-chemical characterization using instrumental techniques like BET etc. The surface acidic properties were determined by the ammonia TPD studies, Perylene absorption studies and Cumene conversion reaction. The catalytic activities of the prepared systems are tested by Friedel-Crafts benzylation of arenes and Bechmann rearrangement of Cyclohexanol oxime. Here the rector reactions are relatively rare. So to test the application of the catalyst systems for the selective oxidation of cyclohexanol to cyclohexanone and finally evaluate the catalytic activity of the systems for the vapour phase oxidative dehydrogenation of Ethylbenzene, which leads to the formation of Industrially important compound ‘styrene’ is another objective of this work

Studies on Some New Metal-Hydrazone Complexes and Their Zeolite Encapsulated Analogues

The thesis deals with the synthesis, characterization and catalytic activity studies of some new Fe (III), Co (II), Ni (II) and Cu (II) complexes of hydrazones and their zeolite encapsulated analogues. Hydrazones have diverse applications in biological, non-biological and biochemical front. During the present study three hydrazone types of ligands namely, acetylacetone- 2-hydroxyphenylhydrazone (APAcAc), acetoacetanilide- 2-hydroxyphenylhydrazone (APAcAcA) and acetoacetanilide-3,5-dihydro-2,4-dione pyrimidylhydrazone (AUAcAcA) were synthesized by diazotization of primary amine and coupling with compounds containing active methylene group. First part of the thesis deals with the synthesis of Fe, Co, Ni and Cu complexes using three hydrazone types of ligands are given. Details regarding the characterization of these complexes with a view to establishing the molecular structures are presented in this part. The other part contains the method of encapsulation of these complexes in zeolite cavities and their characterizations of the encapsulated metal species are described. A comparitive account of the catalytic activities of the pure and encapsulated complexes for cyclohexanol oxidation was also carried out.

Diversity in Structural and Spectural Characteristics of Some Transition Metal Complexes Derived From Aldehyde Based Thiosemicarbazone Ligands

The study deals with the diversity in structural and spectural characteristics of some transition metal complexes derived from aldehyde based thiosemicarbazone ligands thiosemicarbazones are a family of compounds with beneficial biological activity viz., anticancer,antitumour, antifungal, antibacterial, antimalarial, antifilarial, antiviral and anti-HIV activities. Many thiosemicarbazone ligands and their complexes have been prepared and screened for their antimicrobial activity against various types of fungi and bacteria. The results prove that the compounds exhibit antimicrobial properties and it is important to note that in some cases metal chelates show more inhibitory effects than the parent ligands. The increased lipophilicity of these complexes seems to be responsible for their enhanced biological potency. Adverse biological activities of thiosemicarbazones have been widely studied in rats and in other species. The parameters measured show that copper complexes caused considerable oxidative stress and zinc zinc complexes behaved as antioxidants. It has applications on analytical field also. Some thiosemicarbazones produce highly colored complexes with metal ions. This thesis aims to synthesis some novel thiosemicarbazone ligands and their transition metal complexes together with their physico-chemical characterization.

Fabrication Of Potentiometric Sensors For The Determination Of Certain Metal Ions

In this study Fabrication of Potentiometric sensors for the determination of certain metal ions, presents the synthesis and characterization of seven ionophores, their use in the fabrication of potentiometric sensors and the results and discussion of fourteen sensors developed for the determination of five transition metal ions. As part of the present investigations a total of fourteen potentiometric sensors have been developed and fabricated. A three fold approach has been taken in developing he sensors, PVC plasticized membrane sensor, carbon paste electrode and chemically modified carbon paste electrode. All the sensors are highly useful in the determination of metal ions such as manganese, nickel, copper, mercury and lead. A through analytical study has been carried out with respect to each other developed. Based on these studies, optimum conditions have been developed for the quantitative determinations of the selected metal ions using the sensors. Systematic application studies have also been carried out for all the developed sensors and the results revealed that the presently developed sensors are far superior than most of the sensors reported.

Growth and Characterization of ZnO based Heterojunction diodes and ZnO Nanostructuresby Pulsed Laser Ablation

Transparent conducting oxides (TCO’s) have been known and used for technologically important applications for more than 50 years. The oxide materials such as In2O3, SnO2 and impurity doped SnO2: Sb, SnO2: F and In2O3: Sn (indium tin oxide) were primarily used as TCO’s. Indium based oxides had been widely used as TCO’s for the past few decades. But the current increase in the cost of indium and scarcity of this material created the difficulty in obtaining low cost TCO’s. Hence the search for alternative TCO material has been a topic of active research for the last few decades. This resulted in the development of various binary and ternary compounds. But the advantages of using binary oxides are the easiness to control the composition and deposition parameters. ZnO has been identified as the one of the promising candidate for transparent electronic applications owing to its exciting optoelectronic properties. Some optoelectronics applications of ZnO overlap with that of GaN, another wide band gap semiconductor which is widely used for the production of green, blue-violet and white light emitting devices. However ZnO has some advantages over GaN among which are the availability of fairly high quality ZnO bulk single crystals and large excitonic binding energy. ZnO also has much simpler crystal-growth technology, resulting in a potentially lower cost for ZnO based devices. Most of the TCO’s are n-type semiconductors and are utilized as transparent electrodes in variety of commercial applications such as photovoltaics, electrochromic windows, flat panel displays. TCO’s provide a great potential for realizing diverse range of active functions, novel functions can be integrated into the materials according to the requirement. However the application of TCO’s has been restricted to transparent electrodes, ii notwithstanding the fact that TCO’s are n-type semiconductors. The basic reason is the lack of p-type TCO, many of the active functions in semiconductor originate from the nature of pn-junction. In 1997, H. Kawazoe et al reported the CuAlO2 as the first p-type TCO along with the chemical design concept for the exploration of other p-type TCO’s. This has led to the fabrication of all transparent diode and transistors. Fabrication of nanostructures of TCO has been a focus of an ever-increasing number of researchers world wide, mainly due to their unique optical and electronic properties which makes them ideal for a wide spectrum of applications ranging from flexible displays, quantum well lasers to in vivo biological imaging and therapeutic agents. ZnO is a highly multifunctional material system with highly promising application potential for UV light emitting diodes, diode lasers, sensors, etc. ZnO nanocrystals and nanorods doped with transition metal impurities have also attracted great interest, recently, for their spin-electronic applications This thesis summarizes the results on the growth and characterization of ZnO based diodes and nanostructures by pulsed laser ablation. Various ZnO based heterojunction diodes have been fabricated using pulsed laser deposition (PLD) and their electrical characteristics were interpreted using existing models. Pulsed laser ablation has been employed to fabricate ZnO quantum dots, ZnO nanorods and ZnMgO/ZnO multiple quantum well structures with the aim of studying the luminescent properties.

Structural and Spectral Investigations of Transition Metal Complexes Of Di-2-Pyridyl Ketone N (4), N (4)-Disubstituted Thiosemicarbazones

The study deals with structural and spectral investigations of transition metal complexes of di-2-pyridyl ketone N(4),N(4)-disubstituted thiosemicarbazones. The main objective and scope of the work deals with di-2-pyridyl ketone N(4),N(4)-disubstituted thiosemicarbazones are quardridentate NNNS donor ligands. To chosen this ligand for study because, the ligands are prepared and characterized for the first time, since there are two pyridyl nitorgens, dimmers and polymers of complexes may result leading to interesting structural aspects. The work includes the preparation of the thiosemicarbzones and their structural and spectral studies, synthesis and spectral characterization of complexes of copper(II),,nickel(II),manganese(II), dioxovanadium(V),cobalt(III),zinc(II),cadmium(II) of the ligand HL, synthesis and spectral characterization of complexes of copper(II),manganese(II), of the ligand HL and the development of X-ray quality crystals and its X-ray diffraction studies. The structural characterization techniques are elemental analysis, conductivity measurements, magnetic measurements, electronic spectroscopy, H NMR spectroscopy, Infrared spectroscopy and X-ray crystallography.

Studies on Some Simple and Zeolite-Y Encapsulated 3d-Transition Metal Complexes of Schiff Bases Derived From 2-Aminobenzothiazole

In this regard Schiff base complexes have attracted wide attention. Furthermore, such complexes are found to play important role in analytical chemistry, organic synthesis, metallurgy, refining of metals, electroplating and photography. Many Schiff base complexes are reported in literature. Their properties depend on the nature of the metal ion as well as on the nature of the ligand. By altering the ligands it is possible to obtain desired electronic environment around the metal ion. Thus there is a continuing interest in the synthesis of simple and zeolite encapsulated Schiff base complexes of metal ions. Zeolites have a number of striking structural similarities to the protein portion of natural enzymes. Zeolite based catalysts are known for their remarkable ability of mimicking the chemistry of biological systems. In view of the importance of catalysts in all the areas of modern chemical industries, an effort has been made to synthesize some simple Schiff base complexes, heterogenize them by encapsulating within the supercages of zeoliteY cavities and to study their applications. The thesis deals with studies on the synthesis and characterization of some simple and zeoliteY encapsulated Mn(II), Fe(III), Co(II), Ni(II) and Cu(II) complexes and on the catalytic activity of these complexes on some oxidation reactions. Simple complexes were prepared from the Schiff base ligands SBT derived from 2-aminobenzothiazole and salicylaldehyde and the ligand VBT derived from 2-aminobenzothiazole and vanillin (4-hydroxy-3- methoxybenzaldehyde). ZeoliteY encapsulated Mn(II), Fe(III), Co(II), Ni(II) and Cu(II) complexes of Schiff base ligands SBT and VBT and also of 2-aminobenzothiazole were synthesized. All the prepared complexes were characterized using the physico-chemical techniques such as chemical analysis (employing AAS and CHN analyses), magnetic moment studies, conductance measurements and electronic and FTIR spectra. EPR spectra of the Cu(II) complexes were also carried out to know the probable structures and nature of Cu(II) complexes. Thermogravimetric analyses were carried out to obtain the information regarding the thermal stability of various complexes. The successful encapsulations of the complexes within the cavities of zeoliteY were ascertained by XRD, surface area and pore volume analysis. Assignments of geometries of simple and zeoliteY encapsulated complexes are given in all the cases. Both simple and zeoliteY encapsulated complexes were screened for catalytic activity towards oxidation reactions such as decomposition of hydrogen peroxide, oxidation of benzaldehyde, benzyl alcohol, 1-propanol, 2-propanol and cyclohexanol.