中国北方草本植物及表土有机质碳同位素组成

Recently, more and more attention has been paid to stable isotope ratios in terrestrial depositional systems. Among them, δ~(13)C value is mainly determined by the surface vegetation, while vegetation is directly related to climate, therefore, carbon isotope ratio in soil organic matter and pedogenic carbonate has been employed as an important paleoecological indicator. In order to test the paleoecological information extracted from stable isotope ratios in terrestrial depositional systems, it is necessary to study the relationships between δ~(13)C value in standing terrestrial plants and today climate, as well as between δ~(13)C value in modern surface soil organic matter and standing vegetation. Thus, these relationships were studied in this paper by means of analysing δ~(13)C in standing plants and modem surface soil organic matter in North China. The main results and conclusions are presented as following: 1. According to their δ~(13)C values, 40 C-4 species represent about 16% of the 257 plant species sarnpled from the North China. C-4 photosynthesis mainly occurs in Poaceae, Cyperaceae and Chenopidaceae families, and percentage representation of C-4 photosynthesis is up to 56% in Poaceae family. 2. The δ~(13)C values of C-3 plant species in North China vary from -21.7‰ to -32.0‰ with an average of -27.1‰, and 93% focus on the range of -24.0‰ ～ -30.0‰; δ~(13)C values of C-4 plant species in North China are between -10.0‰ ～ -15.5‰ with an average of -12.9‰, and 90% concentrate on the range of -11.0‰ ～ -15.0‰. 3. The δ~(13)C composition of C-3 plant species collected from Beijing, a semi-moist district, mainly vary between -27.0‰ ～ -30.0‰, and the average is -28.7‰; the δ ~(13)C values of plants in the semi-arid district, east and west to the Liu Pan Moutain, focus on the range of-26.0‰ ～ -29.0‰ and -25.0‰ ～ -28.0‰, respectively, with the mean value of -27.6‰ and -26.6‰, respectively; the δ~(13)C composition in the arid district dominantly vary from -24.0‰ to -29.0‰, with the average of -26.2‰, and among them, the δ~(13)C values of C-3 plant species in deserts are often between - 22‰ ～ -24‰; the δ~(13)C values in the cold mountain district concentrate on the range of -24.0‰ to -29.0‰, with the average of -26.3‰. 4. The main range of δ~(13)C composition of C-4 plant species, derived from Beijing, a semi-moist district, are -13.0‰ ～ -15.5‰; the semi-arid district, -11.0‰ ～ -14.0‰; the arid district, -11.0‰ ～ -14.0‰. The mean values of them are -14.0‰, -12.4‰,-12.7‰, respectively. 5. From east to west in North China, δ~(13)C values of C-3 plant species increase with longitude. The correlation between δ~(13)C ratios of C-3 plant species and longitude is linear. Changing temperate and precipitation and changing atmosphere pressure are spossible explanations. 6. Almost all C-3 plant species have the trends that their δ~(13)C values gradually increase with decreasing precipitation, decreasing temperature and increasing altitude. Our results show the increases of the δ~(13)C value by 0.30 ～ 0.45‰, 0.19 ～ 0.27‰ and 1.1 ～ 1.2‰ per 100 mm, I℃ and 1000 m, respectively, for all C-3 plant species together. 7. The δ~(13)C values of all C-3 plant species together and a part of C-3 species show highly significant linear correlation with the mean annual temperature, the mean annual precipitation and the altitude, and the results suggest that they can be used as proxies of these environmental variables, while, those without highly significant correlation, may be not suitable as the proxies. 8. The extent, which of responses of δ~(13)C composition to environmental variables, is different for each C-3 plant specie. 9. The δ~(13)C variations along altitude and longitude may be non-linear for C-4 p1ant species in North China. The mean annual temperature may be not important influential factor, thus, it suggests that the δ~(13)C composition of C-4 plant species may be not suitable as the proxy of the mean annual temperature. The influences of summer temperature on δ~(13)C values are much bigger than that of annual temperature, among them, the influence of September temperature is biggest. The mean annual precipitation may be one of the dominant influential factors, and it shows a highly significant non-linear relationship with δ~(13)C values, and the result indicates that δ~(13) C composition of C-4 plant species can be employed as the proxy of the mean annual precipitation. 10. The variations of δ~(13)C ratios do not show systematic trends along longitude, latitude and altitude for modern surface soil organic in Northwest China. ll. The δ~(13)C ratios of modern surface soil organic do not exhibit systematic patterns with temperature and precipitation in Northwest China, it suggests that, unless soil organic is transferred from pure C-3 or C-4 vegetation, the δ~(13)C composition of soil organic may be not used as proxies of climatic variables. 12. The δ~(13)C values of modem surface soil organic are heavier than that of standing vegetation, and the difference ofrnean δ~(13)C between them is -2.18‰. 13. Without considering the δ~(13)C difference between vegetation and soil organic, as well as the δ~(13)C drift in various enviromnent, we may not obtain the valuable information of C-3, C-4 relative biomass in vegetation. 14. The C-4 biomass contribution in vegetation increase with decreasing latitude, increasing longitude and decreasing altitude in Northwest China. The C-4 biomass almost are zero in those regions north to 38 ° N, or west to 100°E, or above 2400 m. 15. The C-4 relative biomass in vegetation increase with growing temperature and precipitation. and, C-4 plants are rare at those regions where the mean annual temperature is less 4 ℃, or the mean annual precipitation is less 200 mm, and their biomass contribution in vegetation are almost zero. Both the mean annual temperature and the mean annual average precipitation may be the important influential factors of C-4 distribution, but the dominant factors.

辽河盆地东部凹陷热历史及其与油气关系

This dissertation focuses on the basin geothermal history, tectonothermal evolution and the relationship between geothermal field evolution and hydrocarbon generation. Based on the research of present-day geothermal field, geothermal history of Eastern Subdepression of Liaohe Basin was reconstructed with available data from drillings, loggings, seismic cross-sections, BHTs and thermal indicators. 12 heat flow density values were calculated. Ranging from 45.7 mW/m~2 to 70.0 mW/m~2, the mean value of these determinations exhibits 58.0(±5.83mW/m~22). The heat flow density in the uplift and ramp is greater than that in the sag. The main factors affecting the heat flow density are the morphostructure of basement and thickness of sedimentary cover. The Subdepression experienced a much higher heat flow period from 43 Ma to about 25 Ma. The heat flow increased gradually from Sha3 stage to Dongying stage, and reached the peak at the late of Dongying stage, then cooled down. Structural subsidence analysis shows that the subsidence of Eastern Subdepression can be divided into two phases: earlier (25-43Ma) initial (rift) and late (since 25Ma) thermal subsidence. The lower present-day heat flow and the higher palaeo-heat flow corresponding to structural subsidence stage as well as the typical rift subsidence style in Eastern Subdepression provide with some insights to the tectonic-thermal evolution of the basin. The source rocks of Sha3 member began to generate oil in the Shal stage, and entered oil-window at the late of Dongying stage. The source rocks of Shal began to generate oil at the late of Dongying stage, and being at the stage of lower maturation-maturation now. Most of Dongying source rocks are not mature now. The late of Dongying stage is the critical time for the oil system.

中国东海陆架盆地构造-热演化研究

East China Sea Shelf Basin (ECSSB), as a basin with prospect of oil & gas resource and due to its special geological location on the west margin of the west Pacific, attracts a lot of attention from many geologists in the world.Based on systematic temperature measurements, bottom hole temperature (BHT) and the oil temperature data, the geothermal gradients in the ECS SB are calculated and vary from 25 to 43°C/km, with a mean of 32.7°C/km. The geothermal gradient in Fuzhou Sag has the higher value(40.6°C/km) in Taibei Depression than that in others. The lower value (27.2 °C/km) occurs in in Xihu Depression. The middle values occurs in Jiaojiang and Lishui sags in Taibei Depression with a mean value of 34.8 °C/km. Incorporated with the measured thermal conductivity, heat flow values show that the ECSSB is characterized by present-day heat flow around 70.6mW/m2, varying between 55 and 88 mW/m2. No significant difference in heat flow is observed between the Xihu and the Taibei Depressions. These heat flow data suggest that the ECSSB is geothermally not a modem back-arc basin.Applying the paleogeothermal gradient based method, thermal history is reconstructed using vitrinite reflectance (VR) and apatite fission track (AFT) data. The results suggest that the thermal history was different in the Taibei and the Xihu depressions. Paleo-heat flow values when the pre-Tertiary formations experienced their maximum temperature at the end of the Paleocene reached a mean of 81 mW/m2 in the Taibei Depression, much higher than the present-day value. The lower Tertiary sediments in the Xihu Depression experienced maximum temperatures at the end of Oligocene and reached a mean paleo-heat flow value of 83.4 mW/m2. The time, when the paleo-heat flow reached the maximum value, suggests that the ECSSB rifted eastward.Tectonic subsidence analysis shows that the timing of the major rifting episode was different across the ECSSB. The rifting occurred from the Late Cretaceous to the early Eocene in the Taibei Depression, followed by thermal subsidence from the late Eocene to the end of Miocene. In contrast, in the Xihu Depression the initial subsidence lasted until the early Miocene and thermal subsidence to the end of Miocene. From Pliocene to the present, an accelerated subsidence took place all along the West Pacific margin of the east Asia.The thermal lithosphere thickness is determined by temperature profile in the lithosphere, the mantle adiabat or the dry basalt solidus. It indicates that the thermal lithosphere reached the thinnest thickness at the end of Eocene in the Taibei Depression and the end of Oligocene in the Xihu Depression, respectively, corresponding with a value of 57-66km and 56-64km. In Taibei Depression, the lithosphere thickness decreased 16-22km from the end of Mesozoic to Paleocene. After Paleocene, the thickness increased 13-16km and reached 71-79 km at present-day. In Xihu Depression, From the end of Oligocene to present-day, the thickness increased 10-13km and reached 69-76km at present-day. The evolution of the lithosphere thickness is associated closely with the lithosphere stretching.Combining the reconstructed thermal history and the burial history, the maturation of the Jurassic oil-source rock shows that the main hydrocarbon generation phase was in the mid-Jurassic and a secondary hydrocarbon generation occurred at the end of Paleocene. The secondary generation was controlled mainly by the tectono-thermal background during the Paleocene.

Development and validation of a sport-specific exercise protocol for elite youth soccer players

Thatcher, Rhys, and Alan Batterham, 'Development and validation of a sport-specific exercise protocol for elite youth soccer players', Journal of Sports Medicine and Physical Fitness, (2004) 44(1) pp.15-22 RAE2008

The effect of variability in the powder/liquid ratio on the strength of zinc phosphate cement

Aim: To investigate (a) variability in powder/liquid proportioning (b) effect of the extremes of any such variability on diametral tensile strength (DTS), in a commercial zinc phosphate cement. Statistical analyses (a = 0.05) were by Student's t-test in the case of powder/liquid ratio and one-way ANOVA and Tukey HSD for for pair-wise comparisons of mean DTS. The Null hypotheses were that (a) the powder-liquid mixing ratios observed would not differ from the manufacturer's recommended ratio (b) DTS of the set cement samples using the extreme powder/liquid ratios observed would not differ from those made using the manufacturer's recommended ratio. Methodology: Thirty-four undergraduate dental students dispensed the components according to the manufacturer's instructions. The maximum and minimum powder/liquid ratios (m/m), together with the manufacturer's recommended ratio (m/m), were used to prepare cylindrical samples (n = 3 x 34) for DTS testing. Results: Powder/liquid ratios ranged from 2.386 to 1.018.The mean ratio (1.644 (341) m/m) was not significantly different from the manufacturer's recommended value of 1.718 (p=0.189). DTS values for the maximum and minimum ratios (m/m), respectively, were both significantly different from each other (p<0.001) and from the mean value obtained from the manufacturer's recommended ratio (m/m) (p<0.001). Conclusions: Variability exists in powder/liquid ratio (m/m) for hand dispensed zinc phosphate cement. This variability can affect the DTS of the set material.

A two-dimensional numerical investigation of the oscillatory flow behaviour in rectangular fire compartments with a single horizontal ceiling vent

This paper presents a comparison of fire field model predictions with experiment for the case of a fire within a compartment which is vented (buoyancydriven) to the outside by a single horizontal ceiling vent. Unlike previous work, the mathematical model does not employ a mixing ratio to represent vent temperatures but allows the model to predict vent temperatures a priori. The experiment suggests that the flow through the vent produces oscillatory behaviour in vent temperatures with puffs of smoke emerging from the fire compartment. This type of flow is also predicted by the fire field model. While the numerical predictions are in good qualitative agreement with observations, they overpredict the amplitudes of the temperature oscillations within the vent and also the compartment temperatures. The discrepancies are thought to be due to three-dimensional effects not accounted for in this model as well as using standard ‘practices’ normally used by the community with regards to discretization and turbulence models. Furthermore, it is important to note that the use of the k–ε turbulence model in a transient mode, as is used here, may have a significant effect on the results. The numerical results also suggest that a linear relationship exists between the frequency of vent temperature oscillation (n) and the heat release rate (Q0) of the type n∝Q0.290, similar to that observed for compartments with two horizontal vents. This relationship is predicted to occur only for heat release rates below a critical value. Furthermore, the vent discharge coefficient is found to vary in an oscillatory fashion with a mean value of 0.58. Below the critical heat release rate the mean discharge coefficient is found to be insensitive to fire size.

Is there a connection between high transport of water through the Rockall Trough and ecological changes in the North Sea?

Changes in the ecosystem of the North Sea may occur as pronounced inter-annual and step-wise shifts as well as gradual trends. Marked inter-annual shifts have occurred at least twice in the last two decades, the late 1980s and the late 1990s, that appear to reflect an increased inflow of oceanic water and species. Numerical modelling has demonstrated a link between altered rates of inflow of oceanic water into the northern North Sea and a regime shift after 1988. In 1989 and 1997 oceanic species not normally found in the North Sea were observed there, suggesting pulses of oceanic water had entered the basin and triggered the subsequent ecosystem change. The oceanic water has origins mainly west of Britain in the Rockall Trough, where the long-term mean volume transport is around 3.7Sv northwards (1Sv=10 super(6)m super(3)s super(1)), but in early 1989 and early 1998 was observed to be more than twice the mean value, reaching over 7Sv. These periods of high transport coinciding with the inferred pulses of oceanic water into the North Sea suggest a connection through the continental shelf edge current. Copyright 2001 International Council for the Exploration of the Sea

Seasonal-Changes In The Physiology Reproductive Condition And Carbohydrate Content Of The Cockle Cardium (=Cerastoderma) Edule (Bivalvia Cardiidae)

Pronounced seasonal cycles in the rates of oxygen consumption and feeding were found for Cardium (=Cerastoderma) edule L. measured in the field under ambient conditions. The cockles had a maximum rate of oxygen consumption (0.89 ml O2 g-1 h-1) in April which declined to a minimum of 0.35 ml O2 g-1 h-1 in March. Their feeding rate was variable but had a maximum value (3.91 l g-1 h-1) in April and a minimum value (0.73 l g-1 h-1) in October. There was no apparent seasonal variation in absorption efficiency, with a mean value of 67.6%. Gametogenesis was initiated in January and the population reached a peak in reproductive condition in April/May, followed by a 3 month spawning period. Carbohydrate reserves were synthesised during spawning, and were then utilised during the winter and early spring. An adaptive function for a reduction in time spent feeding is postulated, and correlations between the rates of certain physiological processes and some exogenous and endogenous variables are discussed.

Coccolithophore surface distributions in the North Atlantic and their modulation of the air-sea flux of CO2 from 10 years of satellite Earth observation data

Coccolithophores are the primary oceanic phytoplankton responsible for the production of calcium carbonate (CaCO3). These climatically important plankton play a key role in the oceanic carbon cycle as a major contributor of carbon to the open ocean carbonate pump (similar to 50 %) and their calcification can affect the atmosphere-to-ocean (air-sea) uptake of carbon dioxide (CO2) through increasing the seawater partial pressure of CO2 (pCO(2)). Here we document variations in the areal extent of surface blooms of the globally important coccolithophore, Emiliania huxleyi, in the North Atlantic over a 10-year period (1998-2007), using Earth observation data from the Sea-viewing Wide Field-of-view Sensor (SeaWiFS). We calculate the annual mean sea surface areal coverage of E. huxleyi in the North Atlantic to be 474 000 +/- 104 000 km(2), which results in a net CaCO3 carbon (CaCO3-C) production of 0.14-1.71 Tg CaCO3-C per year. However, this surface coverage (and, thus, net production) can fluctuate inter-annually by -54/+81% about the mean value and is strongly correlated with the El Nino/Southern Oscillation (ENSO) climate oscillation index (r = 0.75, p < 0.02). Our analysis evaluates the spatial extent over which the E. huxleyi blooms in the North Atlantic can increase the pCO(2) and, thus, decrease the localised air-sea flux of atmospheric CO2. In regions where the blooms are prevalent, the average reduction in the monthly air-sea CO2 flux can reach 55%. The maximum reduction of the monthly air-sea CO2 flux in the time series is 155 %. This work suggests that the high variability, frequency and distribution of these calcifying plankton and their impact on pCO(2) should be considered if we are to fully understand the variability of the North Atlantic air-to-sea flux of CO2. We estimate that these blooms can reduce the annual N. Atlantic net sink atmospheric CO2 by between 3-28 %.

The origin of sub-surface source waters define the sea-air flux of methane in the Mauritanian Upwelling, NW Africa

Concentrations and flux densities of methane were determined during a lagrangian study of an advective filament in the permanent upwelling region off western Mauritania. Newly upwelled waters were dominated by the presence of North Atlantic Central Water and surface CH4 concentrations of 2.2 ± 0.3 nmol L-1 were largely in equilibrium with atmospheric values, with surface saturations of 101.7 ± 14%. As the upwelling filament aged and was advected offshore, CH4 enriched South Atlantic Central Water from intermediate depths of 100 to 350m was entrained into the surface mixed layer of the filament following intense mixing associated with the shelf break. Surface saturations increased to 198.9 ± 15% and flux densities increased from a mean value over the shelf of 2.0 ± 1.1 µmol m-2d-1 to a maximum of 22.6 µmol m-2d-1. Annual CH4 emissions for this persistent filament were estimated at 0.77 ± 0.64 Gg which equates to a maximum of 0.35% of the global oceanic budget. This raises the known outgassing intensity of this area and highlights the importance of advecting filaments from upwelling waters as efficient vehicles for air-sea exchange.

Pullout test correlations and in-place strength assessment - the European Concrete Frame Building Project

A full-scale, seven-story, reinforced concrete building frame was constructed in-place at the Building Research Establishment's Cardington Laboratory, which encompassed a range of different concrete mixtures and advanced construction techniques. This provided an opportunity to assess in-place nondestructive test methods, namely the pullout test, and more specifically the Danish version, which has been known as the Lok test, on a systematic basis during the construction of the building. It was used in conjunction with both standard and temperature-matched cube specimens to assess its practicality and accuracy under site conditions. Strength correlations were determined using linear and power function regression analysis. Strength predictions from these were found to be in very good agreement with the compressive strengths of temperature-matched cube specimens. When a general correlation is used, however, estimates for compressive strength are likely to have 95% confidence limits of around '20% of the mean value of four results.

A study of the Type II-P supernova 2003gd in M74

We present photometric and spectroscopic data of the Type II-P supernova (SN II-P) 2003gd, which was discovered in M74 close to the end of its plateau phase. SN 2003gd is the first Type II supernova ( SN) to have a directly confirmed red supergiant ( RSG) progenitor. We compare SN 2003gd to SN 1999 em, a similar SN II-P, and estimate an explosion date of 2003 March 18. We determine a reddening towards the SN of E(B-V) = 0.14 +/- 0.06, using three different methods. We also calculate three new distances to M74 of 9.6 +/- 2.8, 7.7 +/- 1.7 and 9.6 +/- 2.2 Mpc. The former was estimated using the standard candle method (SCM), for Type II supernovae (SNe II), and the latter two using the brightest supergiants method (BSM). When combined with existing kinematic and BSM distance estimates, we derive a mean value of 9.3 +/- 1.8 Mpc. SN 2003gd was found to have a lower tail luminosity compared with other normal Type II-P supernovae ( SNe II-P) bringing into question the nature of this SN. We present a discussion concluding that this is a normal SN II-P, which is consistent with the observed progenitor mass of 8(-2)(+4) M-circle dot.

Atomic layer deposition of hafnium oxide dielectrics on silicon and germanium substrates

Hafnium oxide films have been deposited at 250 °C on silicon and germanium substrates by atomic layer deposition (ALD), using tetrakis-ethylmethylamino hafnium (TEMAH) and water vapour as precursors in a modified Oxford Instruments PECVD system. Self-limiting monolayer growth has been verified, characterised by a growth rate of 0.082 nm/ cycle. Layer uniformity is approximately within ±1% of the mean value. MOS capacitors have been fabricated by evaporating aluminium electrodes. CV analysis has been used to determine the bulk and interface properties of the HfO 2, and their dependence on pre-clean schedule, deposition conditions and post-deposition annealing. The dielectric constant of the HfO 2 is typically 18. On silicon, best results are obtained when the HfO 2 is deposited on a chemically oxidised hydrophilic surface. On germanium, best results are obtained when the substrate is nitrided before HfO 2 deposition, using an in-situ nitrogen plasma treatment. © Springer Science+Business Media, LLC 2007.

One-dimensional particle simulation of the filamentation instability: Electrostatic field driven by the magnetic pressure gradient force

Two counterpropagating cool and equally dense electron beams are modeled with particle-in-cell simulations. The electron beam filamentation instability is examined in one spatial dimension, which is an approximation for a quasiplanar filament boundary. It is confirmed that the force on the electrons imposed by the electrostatic field, which develops during the nonlinear stage of the instability, oscillates around a mean value that equals the magnetic pressure gradient force. The forces acting on the electrons due to the electrostatic and the magnetic field have a similar strength. The electrostatic field reduces the confining force close to the stable equilibrium of each filament and increases it farther away, limiting the peak density. The confining time-averaged total potential permits an overlap of current filaments with an opposite flow direction.

Composition profiling of seized ecstasy tablets by Raman spectroscopy

Raman spectroscopy with far-red excitation has been investigated as a simple and rapid technique for composition profiling of seized ecstasy (MDMA, N-methyl-3,4-methylenedioxyamphetamine) tablets. The spectra obtained are rich in vibrational bands and allow the active drug and excipient used to bulk the tablets to be identified. Relative band heights can be used to determine drug/excipient ratios and the degree of hydration of the drug while the fact that 50 tablets per hour can be analysed allows large numbers of spectra to be recorded. The ability of Raman spectroscopy to distinguish between ecstasy tablets on the basis of their chemical composition is illustrated here by a sample set of 400 tablets taken from a large seizure of > 50000 tablets that were found in eight large bags. The tablets are all similar in appearance and carry the same logo. Conventional analysis by GC-MS showed they contained MDMA. Initial Raman studies of samples from each of the eight bags showed that despite some tablet-to-tablet variation within each bag the contents could be classified on the basis of the excipients used. The tablets in five of the bags were sorbitol-based, two were cellulose-based and one bag contained tablets with a glucose excipient. More extensive analysis of 50 tablets from each of a representative series of sample bags gave distribution profiles that showed the contents of each bag were approximately normally distributed about a mean value, rather than being mixtures of several discrete types. Two of the sorbitol-containing sample sets were indistinguishable while a third was similar but not identical to these, in that it contained the same excipient and MDMA with the same degree of hydration but had a slightly different MDMA/sorbitol ratio. The cellulose-based samples were badly manufactured and showed considerable tablet-to-tablet variation in their drug/excipient ratio while the glucose-based tablets had a tight distribution in their drug/excipient ratios. The degree of hydration in the MDMA feedstocks used to manufacture the cellulose-, glucose- and sorbitol-based tablets were all different from each other. This study, because it centres on a single seizure of physically similar tablets with the same active drug, highlights the fact that simple physical descriptions coupled with active drug content do not in themselves fully characterize the nature of the seized materials. There is considerable variation in the composition of the tablets within this single seizure and the fact that this variation can be detected from Raman spectra demonstrates that the potential benefits of obtaining highly detailed spectra can indeed translate into information that is not readily available from other methods but would be useful for tracing of drug distribution networks.