Crescimeno de apatita na superfície da liga Ti-7, 5Mo empregando tratamento higrotérmico

The objective of the present work was to evaluate surface of experimental alloy Ti-7.5Mo after hydrothermal treatment. Ingots were obtained in arc melting furnace under an argon atmosphere and then homogenized under vacuum at 1100ºC for 86.4 ks to eliminate chemical segregation and after cold worked discs were cutting and grinding. For surface treatment, samples were immersed in a container with NaOH aqueous solution 5M, autoclaved, washed with distilled water. Followed, samples were heat treated and they were soaking in 5xSBF to form an apatite layer on the surface. Surfaces were investigated by, scanning electron microscopy, X-Rays powder diffraction, atomic force microscopy and contact angle, in order to evaluate the wettability of the alloy surface. The results were compared with our previous studies using the group of chemical surface treatments and results shows better condition is 120 minutes in the autoclave

Crescimento de apatita na superfície da liga Ti-25Ta empregando dois tipos de tratamento de superfície: biomimético e deposição de polímero por eletrofiação

Titanium and its alloys has been widely used as materials for metallic biomaterials implants are usually employed to restore the hard tissue function, being used for artificial joints and bones, synthetic plates, crowns, dental implants and screws . Objective of this work was the surface modification of Ti-alloy 25Ta from biomimetic surface treatment of employment and deposition of polymer by electrospinning. The league was obtained from the fusion of the pure elements in the arc furnace with controlled atmosphere. The ingots were subjected to heat treatment, cold forged and sectioned discs with 13 mm diameter and 3 mm thick. Two surface treatments was evaluated, biomimetic and electrospinning with PCL fiber. The biomimetic treatment was performed involving alkaline treatment for three molarities 1.5M, 3M and 5M with immersion in SBF. The electrospinning was performed using PCL polymer alloy surface after the alkali treatment Ti25Ta 1M. For this group the polymer coated surfaces were immersed in calcium phosphate containing solution for immobilization of apatite. The results were compared with previous studies using surface treatment group to verify hydroxyapatite formation on the sample surface and it is concluded that the best condition is biomimetic treatment with 5M alkali treatment and heat treatment at 80 ° C for 72 hours

Incorporação da apatita na superfície da liga Ti30ta empregando tratamento alcalino associado à eletrofiação de fibras de PCL

Pós-graduação em Engenharia Mecânica - FEG

Tratamento de superfície de implantes dentários: SBF

Various surface treatments of dental implants have been developed in order to ensure anchorage to bone tissue, optimization of the determinants of electronic structure, crystallinity, composition and properties. Coating techniques have been proposed in order tocreate unionbiochemicalable to accelerate the early stages ofbone tissue, combining the positive properties of titanium and its alloys bioactivity of ceramic materials. This paper discusses protocol for handling the SBF coating of titanium alloys. The apatite phase nucleation occurs by immersing the substrate in synthetic solution simulating blood plasma (Simulated Body Fluid). The protocol allows manipulation of the SBF solution to establish guidelines regarding the usestreamlinedand organized to make practical application.

Estudo do efeito do transporte de massa nas curvas de polarização potenciodinâmica em ligas de alumínio da série 7XXX de aplicação aeronáutica

Aluminum Alloys are widely used as structural materials in the aerospace industry due to low weight, high mechanical strength and enduring corrosion resistance. Their resistance to corrosion is attributed to the rapidly formed stable oxide film (Al2O3) which spontaneously forms itself on the surface of the material. However, in the presence of aggressive ions, such as halide, Aluminum Alloys are subject to a localized process of corrosion. The electrochemical behavior of 7081-T73511 and 7050-T7451 Aluminum Alloys employed in the aerospace industry was investigated using a 0.6 M NaCl solution under the conditions of a controlled mass transport employing a rotating disk electrode. The theoretical limiting current density was determined by the Kouteki-Levich equation. The results confirmed that the inter-metallic Al7Cu2Fe acts as preferential cathode generating the galvanic coupling and the dissolution of the Aluminummatrix around it.

Caracterização da liga Ti-30Ta após tratamento biomimético associado à incorporação de antibiótico

Surface treatments have been used to modify the surface of titanium alloys. The purpose of this study is to evaluate the surface of Ti-30Ta alloy after biomimetic approach associated to antibiotic incorporation. The ingots were obtained in arc melting furnace, treated and cold-worked by swaging. The surface treatment was performed in two steps: biomimetic treatment and antibiotic incorporation. For biomimetic treatment, first an alkaline treatment (NaOH 1M at 60ºC) was performed, followed by heat treatment and immersion in SBFx5 (Simulated Body Fluid) for a period of 24 hours. In order to incorporate the antibiotic, samples were immersed in a solution formed by drugs plus SBFx5 for 48 hours. The sample surfaces were analyzed by scanning electron microscopy (SEM), X-Ray diffraction (XRD), atomic force microscopy (AFM) and contact angle measurements. The release of antibiotic from coated implants was measured in phosphate buffer saline at pH 7.4 by using UV/VIS spectrometry. Results have shown changes on the surface after incorporating the drug, which is gradually co-precipitated with the Ca-P crystals, forming a uniform and rough layer on the metal surface

Caracterização da liga Ti-30Ta após tratamento biomimético associado à incorporação de antibiótico

Surface treatments have been used to modify the surface of titanium alloys. The purpose of this study is to evaluate the surface of Ti-30Ta alloy after biomimetic approach associated to antibiotic incorporation. The ingots were obtained in arc melting furnace, treated and cold-worked by swaging. The surface treatment was performed in two steps: biomimetic treatment and antibiotic incorporation. For biomimetic treatment, first an alkaline treatment (NaOH 1M at 60ºC) was performed, followed by heat treatment and immersion in SBFx5 (Simulated Body Fluid) for a period of 24 hours. In order to incorporate the antibiotic, samples were immersed in a solution formed by drugs plus SBFx5 for 48 hours. The sample surfaces were analyzed by scanning electron microscopy (SEM), X-Ray diffraction (XRD), atomic force microscopy (AFM) and contact angle measurements. The release of antibiotic from coated implants was measured in phosphate buffer saline at pH 7.4 by using UV/VIS spectrometry. Results have shown changes on the surface after incorporating the drug, which is gradually co-precipitated with the Ca-P crystals, forming a uniform and rough layer on the metal surface

Efeitos da terapia fotodinâmica com aluminio – cloro ftalocianina sobre a peroxidação lipídica e produtos antioxidantes em tecidos inflamados animais

Photodynamic therapy (PDT) consists of a non-toxic photosensitizing agent (FS) administration followed by a laser source resulting in a sequence of photochemical and photobiological processes that generate reactive oxygen species (ROS) that damaging cells. The present work evaluated the effects of PDT nanoemulsion-aluminum chloride phthalocyanine (AlClFc) mediated on malondialdehyde (MDA), glutathione (GSH), superoxide dismutase (SOD) and glutathione peroxidase (GPx) levels, which represent indicators involved in oxidative stress and antioxidant defenses. For this purpose, this study used 120 female rats of the Rattus norvegicus species, Wistar race, divided into 5 groups: Healthy (H), with periodontal disease (PD), with periodontal disease and treatment with FS (F), with periodontal disease and treatment with the laser (L); and periodontal disease and treatment with PDT (FL). An experimental model for represent periodontal disease (PD) was induced by ligature (split-mouth). Seven days later the induction of PD, the treatments were instituted according to the groups. In the group treated with PDT was applied 40μl FS (5μM) followed by laser irradiation diode InGaAlP (660nm, 100J / cm2). The rats were sacrificed on the 7th and 28th day after treatment and tissue specimens were removed and subjected to histological, immunohistochemical methods and enzymatic colorimetric measurements with detection by UV / VIS spectroscopy. Inflammatory changes, connective tissue disorganization and alveolar bone loss were displaying in groups with PD induced. The enzyme dosages showed that MDA levels were higher in PD induced groups, with no statistically significant differences (p> 0.05). High levels of GSH were found in groups L (p = 0.028) and FL (p = 0.028) compared with PD group, with statistically significant differences. Immunohistochemistry for SOD showed higher immunostaining in L and FL groups, compared to the PD group without statistically significant differences (p> 0.05). GPx showed lower immunoreactivity in the DP group when compared to the other groups and statistically significant differences were observed between the DPxL groups (p <0.05). TFD administered in this experiment did not induce elevation of MDA levels significantly increased the GSH levels and showed intense immunostaining pada SOD and GPx, showing that this therapy does not accentuated lipid peroxidation, however, it was able to induce effects on the antioxidant defenses processes. The LBI therapy appeared to show photomodulatory promoting effects reduction of the MDA levels, increasing GSH levels and with intense immunostaining for SOD and GPx, demonstrating that laser therapy induced antioxidant effects.

Tratamento térmico do titânio e suas consequências sobre as propriedades físico-químicas e de biocompatibilidade

The titanium and titanium alloys are widely used as biomaterial in biomedical device and so research have been developed aiming to improve and/or better to understand interaction biomaterial/biological environment. The process for manufacturing of this titanium implants usually involves a series of thermal and mechanical processes which have consequence on the final product. The heat treatments are usually used to obtain different properties for each application. In order to understand the influence of these treatments on the biological response of the surface, it was done, in this work, different heat treatments in titanium and analyzed their influence on the morphology, adhesion and proliferation of the pre-osteoblastic cells (MC3T3-E1). For such heat-treated titanium disks were characterized by optical microscopy, contact angle, surface energy, roughness, microhardness, X-ray diffraction and scanning through the techniques (BSE, EDS and EBSD). For the analysis of biological response were tested by MTT proliferation, adhesion by crystal violet and β1 integrin expression by flow cytometry. It was found that the presence of a microstructure very orderly, defined by a chemical attack, cells tend to stretch in the same direction of orientation of the material microstructure. When this order does not happen, the most important factor influencing cell proliferation is the residual stress, indicated by the hardness of the material. This way the disks with the highest level state of residual stress also showed increased cell proliferation

Aplicação de técnicas eletroquímicas na determinação do potencial de corrosividade de ligas de alumínio em água produzida

The resistance of aluminum and their alloys, to the corrosion phenomenon, in aqueous solutions, is a result of the oxide layer formed. However, the corrosion process in the aluminum alloy is associated with the presence a second phase of particles or the presence of chloride ions which promote the disruption of the oxide layer located producing the corrosion process. On the other hand, the term water produced is used to describe the water after the separation of the oil and gas in API separators. The volumes of produced water arrive around 5 more times to the volume of oil produced. The greatest feature of the water is the presence of numerous pollutants. Due to the increased volume of waste around the world in the current decade, the outcome and the effect of the discharge of produced water on the environment has recently become an important issue of environmental concern where numerous treatments are aimed at reducing these contaminants before disposal. Then, this study aims to investigate the electrochemical corrosion behavior of aluminum alloy 6060 in presence of water produced and the influence of organic components as well as chloride ions, by using the electrochemical techniques of linear polarization. The modification of the passive layer and the likely breakpoints were observed by atomic force microscopy (AFM). In the pit formation potential around -0.4 to -0.8 V/EAg/AgCl was observed that the diffusion of chloride ions occurs via the layer formed with the probable formation of pits. Whereas, at temperatures above 65 °C, it was observed that the range of potential for thepit formation was -0.4 to -0.5 V/EAg/AgCl. In all reactions, the concentration of Al(OH)3 in the form of a gel was observed

Evaluación de Actellic 2 (Pirimiphos-methil) y fosfamina (Fosfuro de aluminio) en el control de diferentes poblaciones de sitophilus zeamais motschulsky (Coleoptera: curculionidae) en laboratorio

El trabajo se realizó en el laboratorio del Programa Nacional de Postcosecha 1 INTA, de noviembre de 1994 a agosto de 1995. El objetivo fue evaluar la eficacia de los productos comerciales Actellic (pirimiphos-methil) y Fosfamina (fosfuro de aluminio) en el control de poblaciones del gorgojo del maíz, recolectadas en trojas tradicionales para maíz en comunidades de Matagalpa y Nueva Segovia. Para ejecutar el estudio se realizó una encuesta en Muy Muy, Matagalpa; y Jalapa, Nueva Segovia, para conocer aspectos del almacenamiento de maíz de pequeños productores, con estructuras de almacenamiento tradicionales y mejoradas. Se estableció la metodología para la crianza del gorgojo del maíz en laboratorio, utilizando dieta natural. El producto Actellic 2% se evaluó de tres procedencias contra tres poblaciones de gorgojos recolectadas de tres regiones ecológicamente distintas. Los bioensayos se montaron en frascos plásticos, con una libra de maíz fragmentado, infestado con cien gorgojos. El Actellic 2% se aplicó en base a la dosis comercial. El tiempo de lectura para el Actellic 2% fue de 5 horas. Para los bioensayos con Fosfamina, se utilizaron si los metálicos de 18 quintales. Para estos bioensayos se utilizaron las mismas tres poblaciones de gorgojos. La dosis fue una pastilla por cada cinco quintales de capacidad del silo. El tiempo de lectura fue de cuatro horas, tomando lecturas de la mortalidad del gorgojo a la primera y segunda hora, después cada media hora. Los resultado de la encuesta indican que la principal plaga de almacén, es el gorgojo del maíz; la mayoría de los productores encuestados manifestaron utilizar en sus trojas tradicionales productos altamente tóxicos como DDT, Lorsban y las pastillas de Fosfamina, que son de aplicación en recipientes herméticos. En el silo metálico, los productores ponen menos pastillas de las indicadas. Las procedencias del Actellic 2% evaluadas, y que se comercializan en Nicaragua, no controlaron al gorgojo del maíz. El producto Actellic 2% de Guatemala, demostró un 100% de control del gorgojo del maíz a las cinco horas de exposición. El Tiempo Letal Medio, con el Atellic 2%, para las tres poblaciones del gorgojo del maíz, fue de 129 minutos. Con el producto Fosfamina se obtuvo un Tiempo Letal Medio de 152 minutos contra las tres poblaciones del gorgojo. No hubo diferencia en la susceptibilidad. De las tres poblaciones del gorgojo del maíz con respecto al Actellic 2% y Fosfamina.

Despesas com tratamento de doenças causadas ou agravadas pelo álcool : análise de propostas para seu financiamento

Consultoria Legislativa - Área IX - Política e Planejamento Econômicos, Desenvolvimento Econômico, Economia Internacional.

Radiação das antenas do serviço móvel celular e seu tratamento na legislação brasileira e de outros países

Consultoria Legislativa - Área XIV - Comunicação Social, Informática, Telecomunicações, Sistema Postal, Ciência e Tecnologia.

O uso da lenalidomida para o tratamento do mieloma múltiplo

Apresenta uma abordagem simplificada sobre o câncer mieloma múltiplo para um melhor entendimento dos aspectos envolvidos nessa patologia, destacando os tratamentos atualmente disponíveis e aplicados no combate à referida doença. Aborda aspectos relacionados a substância lenalidomida, sua indicação, efeitos indesejáveis, cuidados no uso, contraindicações, entre outros aspectos. Comenta a respeito da decisão tomada pela Anvisa de não conceder o registro da lenalidomida ao laboratório produtor para sua comercialização no Brasil.

Un método para el taladro de aluminio que facilita la unión por remaches de los componentes aeronáuticos

189 p. : il. col.