955 resultados para LiGaO2 substrate
Resumo:
The possible use of polyethylene naphthalate as substrate for low-temperature deposited solar cells has been studied in this paper. The transparency of this polymer makes it a candidate to be used in both substrate and superstrate configurations. ZnO:Al has been deposited at room temperature on top of PEN. The resulting structure PEN/ZnO:Al presented good optical and electrical properties. PEN has been successfully textured (nanometer and micrometer random roughness) using hot-embossing lithography. Reflector structures have been built depositing Ag and ZnO:Al on top of the stamped polymer. The deposition of these layers did not affect the final roughness of the whole. The reflector structure has been morphologically and optically analysed to verify its suitability to be used in solar cells.
Resumo:
Se estudia la composiciÛn y estructura de la comunidad de macroinvertebrados a lo largo de un transecto en profundidad en el lago Redó (Pirineos). Este estudio se enmarca dentro del proyecto de ámbito europeo MOLAR (Mountain Lake Research). Un equipo de buceadores muestreo dos tipos de substrato, piedras y fondos blandos, cada 2 m desde los 2 a los 20 m de profundidad. En la parte m·s profunda del lago las muestras se tomaron con draga Ekman (tres rÈplicas). Todas las muestras se tomaron el mismo día, el 15 de Julio de 1997. Los resultados, mediante un análisis de autocorrelación de Mantel, muestran que no existe un gradiente continuo en la sustituciÛn de unas especies por otras en la comunidad sobre substrato rocoso, sino que se distinguen dos discontinuidades claras, una a los 4 metros y otra a los 14 metros. La primera separa las especies propias de la zona litoral respecto a las de la zona sublitoral, mientras que la segunda coincide con la parte inferior de la termoclina, una zona siempre mas frÌa, con menos luz y con mayor acumulación de material fino sobre los sustratos duros a la vez que desaparece la cobertura algal que cubrÌa las piedras hasta esta profundidad. Respecto al sustrato existen especies que claramente prefieren el sustrato blando (oligoquetos, o los quironÛmidos Micropsectra radialis y Pseudodiamesa nivosa), mientras que otras eran más abundantes o exclusivas de los sustratos duros (Radix peregra, Plectrocnemia laetabilis, Psectrocladius octomaculatus). Estos resultados seran muy útiles para la interpretaciÛn de los datos paleolimnolÛgicos de los cores que actualmente se est·n estudiando en el lago.
Resumo:
This paper deals with the structural properties of a-Si:H/a-Si1-xCx: H multilayers deposited by glow-discharge decomposition of SiH4 and SiH4 and CH4 mixtures. The main feature of the rf plasma reactor is an automated substrate holder. The plasma stabilization time and its influence on the multilayer obtained is discussed. A series of a-Si:H/a-Si1-xCx: H multilayers has been deposited and characterized by secondary ion mass spectrometry (SIMS), X-ray diffraction (XRD) and transmission electron microscopy (TEM). No asymmetry between the two types of interface has been observed. The results show that the multilayers present a very good periodicity and low roughness. The difficulty of determining the abruptness of the multilayer at the nanometer scale is discussed.
Resumo:
PURPOSE: The goal of this study was to explore the effect of lifelong aerobic exercise (i.e., chronic training) on skeletal muscle substrate stores (intramyocellular triglyceride [IMTG] and glycogen), skeletal muscle phenotypes, and oxidative capacity (ox), in older endurance-trained master athletes (OA) compared with noncompetitive recreational younger (YA) athletes matched by frequency and mode of training. METHODS: Thirteen OA (64.8 ± 4.9 yr) exercising 5 times per week or more were compared with 14 YA (27.8 ± 4.9 yr) males and females. IMTG, glycogen, fiber types, succinate dehydrogenase, and capillarization were measured by immunohistochemistry in vastus lateralis biopsies. Fat-ox and carbohydrate (CHO)-ox were measured by indirect calorimetry before and after an insulin clamp and during a cycle ergometer graded maximal test. RESULTS: V˙O2peak was lower in OA than YA. The OA had greater IMTG in all fiber types and lower glycogen stores than YA. This was reflected in greater proportion of type I and less type II fibers in OA. Type I fibers were similar in size, whereas type II fibers were smaller in OA compared with YA. Both groups had similar succinate dehydrogenase content. Numbers of capillaries per fiber were reduced in OA but with a higher number of capillaries per area. Metabolic flexibility and insulin sensitivity were similar in both groups. Exercise metabolic efficiency was higher in OA. At moderate exercise intensities, carbohydrate-ox was lower in OA but with similar Fat-ox. CONCLUSIONS: Lifelong exercise is associated with higher IMTG content in all muscle fibers and higher metabolic efficiency during exercise that are not explained by differences in muscle fibers types and other muscle characteristics when comparing older with younger athletes matched by exercise mode and frequency.
Resumo:
Agricultural wastes from cactus Cereus peruvianus and Opuntia ficus indica were investigated for protein production by solid substrate fermentation. Firstly, the polyelectrolytes were extracted and used in water cleaning as auxiliary of flocculation and coagulation. The remaining fibrous material and peels were used as substrate for fermentation with Aspergillus niger. Glucoamylase and cellulase were the main enzymes produced. Amino acids were determined by HPLC and protein by Lowry's method. After 120 hours of fermentation the protein increased by 12.8%. Aspartic acid (1.27%), threonine (0.97%), glutamic acid (0.88%), valine (0.70%), serine (0.68%), arginine (0.82%), and phenylalanine (0.51%) were the principal amino acids produced.
Resumo:
Filamentous fungi were cultured under solid state fermentation of soybean residues to produce lipases. Enzymes produced by Aspergillus niger esterified oleic and butyric acids in the presence of ethanol, while enzymes produced by Aspergillus fumigatus demonstrated no esterification activity toward lauric acid. In case of A. niger, direct lyophilization of fermented bran led to higher esterification activity. The esterification of oleic acid by enzymes of A. fumigatus was neither influenced by pH adjustment nor by the extraction process. Conversions to ethyl esters were higher after pH adjustment with lyophilized liquid extract of A. niger.
Resumo:
In vitro experiments were conducted to assess the effects of substrate, temperature and time of exposure to temperature and photoperiod on P. pachyrhizi uredospore germination and germ tube growth. The following substrates were tested: water-agar and soybean leaf extract-agar at different leaf concentrations (0.5, 1.0, 2.0 and 4.0 g of leaves and 15g agar/L water), temperatures (10, 15, 20, 25, 30, and 35oC) and times of exposure (1, 2, 3, 4, 5, 6, 7, and 8 hours) to temperature and 12 different photoperiods. The highest germination and germ tube length was found for the soybean leaf extract agar. Maximum P. pachyrhizi uredospore germination was obtained at 21.8 and 22.3°C, and maximum germ tube growth at 21.4 and 22.1°C. The maximum uredospore germination was found at 6.4 hours exposure, while the maximum germ tube length was obtained at 7.7 h exposure. Regarding photoperiod, the maximum spore germination and the maximum uredospore germ tube length were found in the dark. Neither spore germination nor uredospore germ tube growth was completely inhibited by the exposure to continuous light.
Resumo:
The benefit promoted by ectomycorrhizal depends on the interaction between symbionts and phosphorus (P) contents. Phosphorus effect on ectomycorrhizal formation and the effectiveness of these in promoting plant growth for fungal pre-selection were assessed under in vitro conditions. For P effect evaluation, Eucalyptus urophylla seedlings inoculated with four Pisolithus sp. isolates and others non-inoculated were grown on substrate containing 0.87, 1.16 and 1.72 mg P per plant. For evaluation of effectiveness and fungal pre-selection, other 30 isolates of Pisolithus sp., Pisolithus microcarpus ITA06 isolate, Amanita muscaria AM16 isolate, Scleroderma areolatum SC129 isolate were studied. D26 isolate promoted the highest plant heights for the three P doses, D51 at the lower dose and D72 at the intermediate dose. P doses did not influenced shoot fresh weight and fungal colonization. In the pre-selection of fungi, 14 isolates of Pisolithus sp., P. microcarpus ITA06 isolate and S. areolatum SC129isolate increased plant height and fresh weight. D82 isolate of Pisolithus sp. had effect singly on plant height while D17 and D58 on fresh weight. Of these, only D15, D17, D58 and ITA06 had typical ectomycorrhizae. The cultivation in vitro has shown adequate for pre-selection of ectomycorrhizal fungi. Colonization and benefits depend on species and isolate. D15, D17 and D58 of Pisolithus sp. and P. microcarpus isolate ITA06 are the most promising for nursery studies.
Resumo:
ABSTRACTCallisthene fasciculata Mart. is a tree belonging to the Vochysiaceae family. Its wood is moderately heavy and resistant and used to make poles, beams, and other structures. The aim of this work was to evaluate seed germination and the initial growth of seedlings of C. fasciculata at different temperatures and in different substrates. Seeds were collected from fruits in the Pantanal de Miranda, Mato Grosso do Sul state, Brazil. In one experiment, the seeds were subjected to constant temperatures of 20, 25, 30 and 35 °C and to alternating temperatures of 20-30 and 25-35 °C (on paper substrate). In another experiment, the seeds were subjected to temperatures of 20 and 25 °C on three substrates (sand, vermiculite and between paper) in a germinator. The experiment had a randomized design, with four replicates of 25 seeds per treatment. The F-values obtained for germination indicated no significant effect of substrate or temperature on the final germination percentage. The analyses revealed no effect of a treatment interaction (temperature x substrate) on either germination or average germination time; however, a treatment interaction effect was observed on the germination speed index. The treatment combinations yielding the best performance were between paper substrate at 20 °C and sand substrate at 25 °C. There was a significant effect of the interaction between temperature and substrate on seedling growth, with increased root growth observed in the between paper substrate at 25 °C and increased aerial component growth in both sand at 20 °C and vermiculite at 25 °C. The between paper treatment at 25 °C yielded the greatest final seedling size. Between paper is the most recommended substrate for the production of seedlings due to its ease of handling and lower probability of contamination.
Resumo:
ABSTRACT The macaw palm [Acrocomia aculeata (Jacq.) Lood. ex Mart] has been domesticated to subsidize biodiesel production programs in Brazil. However, little is known about the seedling production of this species. This study aimed to evaluate substrate mixtures, limestone and phosphorus rates for substrate amendment and topdressing frequency in macaw palm seedlings. Three trials were conducted in a greenhouse up to six months of nursery cultivation. Trial 1: determination of percent mineral and organic fractions of seven substrate mixtures. Trial 2: evaluation of four limerates for soil amendment versus four phosphorus rates. Trial 3: evaluation of N, K and Mg topdressing frequency. Significant differences were found in the three trials for most of the variables (plant height, leaf number, shoot dry mass, root dry mass, vigor and bulb diameter). The main results obtained were as follow: Trial1 - the best seedling growth was observed in substrates with at least 25% organic matter. Trial2 -lime rates ranging from 0.50 to 1.25 kg associated with 3 to 4 kg of single superphosphate per m3 of substrate provided the best seedling growth. Trial 3 - topdressing fertilization provided better development of seedlings regardless of frequency.
Resumo:
Culture environments, trays and doses of organic compost were evaluated in the formation of cucumber seedlings (Cucumis sativus L.). Five environmental conditions were tested: (A1) a greenhouse with height of 2.5 m, covered with polyethylene film, (A2) nursery with height of 2.5 m, monofilament fabric, 50% shading, (A3) nursery with height of 2.5 m, heat-reflective screen, 50% shading, (A4) nursery with a height of 1.8 m, covered with coconut tree straw and (A5) greenhouse with height of 4.0 m, covered with polyethylene film, with zenith opening and thermo-reflective cloth under the plastic. Trays of 72 (R1) and 128 (R2) cells were filled with 93% soil and 7% organic compound (S1), 86% soil and 14% organic compound (S2) and 79% soil and 21% organic compound (S3). It was used a randomized design in split-split-plot scheme, with five replicates (environments x trays x substrates). The greenhouses provide the best environments for the formation of cucumber seedlings. A tray of 72 cells is the best container, promoting more vigorous seedlings in substrate with soil and 7 or 14% organic compound.
Resumo:
The Roll-to-Roll process makes it possible to print electronic products continuously onto a uniform substrate. Printing components on flexible surfaces can bring down the costs of simple electronic devices such as RFID tags, antennas and transistors. The possibility of quickly printing flexible electronic components opens up a wide array of novel products previously too expensive to produce on a large scale. Several different printing methods can be used in Roll-to-Roll printing, such as gravure, spray, offset, flexographic and others. Most of the methods can also be mixed in one production line. Most of them still require years of research to reach a significant commercial level. The research for this thesis was carried out at the Konkuk University Flexible Display Research Center (KU-FDRC) in Seoul, Korea. A system using Roll-to-Roll printing requires that the motion of the web can be controlled in every direction in order to align different layers of ink properly. Between printers the ink is dried with hot air. The effects of thermal expansion on the tension of the web are studied in this work, and a mathematical model was constructed on Matlab and Simulink. Simulations and experiments lead to the conclusion that the thermal expansion of the web has a great influence on the tension of the web. Also, experimental evidence was gained that the particular printing machine used for these experiments at KU-FDRC may have a problem in controlling the speeds of the cylinders which pull the web.
Resumo:
Nanotubes are one of the most perspective materials in modern nanotechologies. It makes present investigation very actual. In this work magnetic properties of multi-walled nanotubes on polystyrene substrate are investigated by using quantum magnetometer SQUID. Main purpose was to obtain magnetic field and temperature dependences of magnetization and to compare them to existing theoretical models of magnetism in carbon-bases structures. During data analysis a mathematical algorithm for obtained data filtration was developed because measurement with quantum magnetometer assume big missives of number data, which contain accidental errors. Nature of errors is drift of SQUID signal, errors of different parts of measurement station. Nanotube samples on polystyrene substrate were studied with help of atomic force microscope. On the surface traces of nanotube were found contours, which were oriented in horizontal plane. This feature was caused by rolling method for samples. Detailed comparison of obtained dependences with information of other researches on this topic allows to obtain some conclusions about nature of magnetism in the samples. It emphasizes importance and actuality of this scientific work.
Resumo:
In bromeliad populations, amount of light and available substrates influence individuals spatial organization. In Atlantic Rainforest of Ilha Grande, the heliophylous bromeliad Neoregelia johannis is a large and abundant species. In this forest, it would be expected that N. johannis would occupy stable substrates, as large trunks, large branches, rock boulders or ground, with high sunlight, enough for the bromeliad survivor. In the present work, we analyzed the distribution and most used substrates of N. johannis in secondary forest. We analyzed the frequency of reproductive modes (sexual and vegetative) used by the bromeliad shoots, registering if the shoots were originated from seeds or by vegetative reproduction. The results indicated an aggregated distribution pattern (Ip = 0.052). The preferred substrate was boulders (91%), whereas tree trunks (6%) and the ground (3%) were rarely used. Small and fragile substrates are unstable to support large adults of this species, which may explain the predominant pattern of establishment over boulders within the secondary forest, as the presence of this substrate also results in more opened canopy cover. Approximately 50% of young individuals entered the population by vegetative reproduction. We conclude that the preferential habit and the aggregated distribution of N. johannis are due to the conjunction of preferred substrate with higher amount of light resulting from breaks in tree canopy over areas with rock blocks, and high frequency of recruitment by vegetative reproduction.