Synthesis and characterization of thermotropic liquid crystalline poly(ester imide)s

Two closely series of poly(ester imide)s had been synthesized by solution polycondensation of p-phenylenebis(trimellitate) dianhydride with aliphatic diamines. The differential scanning calorimetry (DSC) traces of the most poly(ester imide)s exhibited two endotherms representing the solid state to anisotropic phase transition (T-m1) and the anisotropic to isotropic melt transition (T-m2), respectively. Observation under polarizing microscope and wide-angle X-ray diffraction (WAXD) measurements suggested that the anisotropic phase formed above the melting paints (T-m1) had a smectic character. The thermogravimetric analyses (TGA) revealed that the thermal stabilities of the poly(ester imide)s were up to 350 degrees C. (C) 1999 John Wiley & Sons, Inc.

Synthesis and Characterization of Side-Chain Liquid Crystalline (M6MPP/M6NPAP) Copolymers with NLO Properties

A series of novel thermotropic side-chain liquid crystalline polymer based on polymethacrylate backbone containing electron-accepting 4-(4'-nitrophenylazo)phenoxy as nonlinear optical active group and electron-donating 4(4'-methoxyphenyl) phenoxy group as mesogen attached covalently to the backbone through the flexible spacer was prepared and characterized, respectively. The results from differential scanning calorimetry showed that these series of copolymers were enantiotropic liquid crystal with single mesophase. The melting points and the relative enthalpy change of the copolymers depressed with increasing the molar percent of 4'-nitroazobenzene monomer units over 0 similar to 50mol%, but the enthalpies change of the transition from mesophase to isotropic state increased for the copolymers containing 0 similar to 50mol% 4'-nitroambenzene units. The texture observed under polarized optical microscope identified that the copolymers containing 24molar% or more than 24mol% 4-nitroambenzene monomer units could form smectic mesophase with the focal-conic texture. The results detected by WAXD were in good agreement with the results observed by POM.

The rheological and extrusion behaviour of blends based on phenolphthalein poly(ether-ether-sulfone) and thermotropic liquid crystalline polymer

A novel engineering thermoplastic, phenolphthalein poly (ether-ether-sulfone) (PES-C) was blended with a commercial thermotropic liquid crystalline polymer(TLCP), Vectra A950, up to 30 weight percent of TLCP. A rheometrics dynamic spectrometer (RDS-I) and a CEAST capillary rheometer, a rheoscope 1000 were employed to investigate the melt rheology and extrusion behaviour at both the low and high shearing rates. The morphologies of the blends under different shearing were observed with a scanning electron microscope(SEM) and correlated to the observed rheology. The principal normal stress differences measured with cone-and-plate geometry give a temperature-independent correlation for both blend and PES-C when they are plotted against shear stress. But the extrudate swell of the blends showed a strong temperature dependence at each shear stress. The concentration dependence of extrudate swell shows a contrary behaviour to that of the inorganic filled system. A reasonable hypothesis based on the relaxation and disorientation of TLCP during flowing in the capillary and exiting was given to explain it. The melt fracture was checked after extrusion from capillary and was discussed.

Studies on the organometallic palladium coordinated carbosillane liquid crystalline dendrimer

A novel complex - palladium-coordinated ate-type liquid crystalline dendrimer was synthesized by a divergent approach, The product showed liquid crystalline properties from 115 degrees C to 187 degrees C, and it belonged to dinuclear species, containing two palladium centers linked by two bridging Cl, each palladium atom completes its coordinations with N atom and a sigma bond to an ortho-carbon in the phenyl ring. The microanalytical values obtained for the product are in agreement with those of compound containing ligand, palladium:and chlorine in a molar ratio of 1 : 1 : 1 and 12 palladium atoms for every scaffold.

Studies on carbosillane liquid crystalline dendrimer with S-c* phase

A liquid crystalline carbosilane dendrimer with Sc* phase has been synthesized in successive steps, resulting in the formation of defined, unimolecular compound. Twelve biphenyl mesogenic units were attached on its periphery and it has a three dimentional, treelike starburst structure. Its phase behavior was K95S(c)*103Ch118I. Compared.with its biphenyl mesogenic unit , 4-(2'-methylbutyl)-4'-(omega-hydroxyhexyl) azobenzene , which was melted at 128 degrees C and is not a liquid crystal, it is a good liquid crystal material with Sc* phase.

Phase identification of triphenylene-based discotic monomer and its main chain polymers

A monomer, 2,3,6,7,10,11-hexakispentyloxy triphenylene (HPT) possesses a triphenylene core as a discotic mesogen. Polymers containing this discotic mesogen have been studied using wide-angle X-ray and electron diffraction. HPT is known to show a discotic liquid crystal phase, noted as D-ho (h for hexagonal bidimensional lattice, o for ordered molecular spacing in each column). In this paper, however, HPT Liquid crystalline phases, heated up from the crystalline state and cooled down from the isotropic state, were characterized in the diameter dimensions. In addition. the diameters of the columns are close to a parameter of two separate crystals. A core orientation was, therefore, proposed in the mesophase obtained by heating the crystalline. In order to distinguish these differences, the D-ho phase was divided to include the D-hcd and D-hco phases. Molecular modeling was performed to help our understanding of the orientation. The D-hcd and D-hco phases were used to characterize the phases of the discotic polymeric analogs by comparing their column diameters to those of the monomers. (C) 1998 Published by Elsevier Science Ltd. All rights reserved.

The synthesis and thermotropic liquid crystalline behaviour of novel main chain poly(aryl ether ketone)s containing a lateral phenyl group

Novel main chain poly(aryl ether ketone)s containing a lateral phenyl group were synthesized by nucleophilic substitution reactions of 4,4'-biphenol and phenylhydroquinone with either 4,4'-difluorobenzophenone or 1,4-bis(4-fluorobenzoyl)benzene and their thermotropic liquid crystalline properties were characterized by a variety of experimental techniques. Thermotropic liquid crystalline behaviour was observed in the copolymers containing 50 and 70mol% biphenol. Melting (T-m) and isotropization (T-i) transitions both appeared on the DSC thermograms. A banded texture was formed after shearing the sample in the liquid crystalline nematic state. As expected, each of the copolymers had a relatively lower melting transition than the biphenol-based homopoly(aryl ether ketone)s because of the copolymerization effect of the crystal-disrupting monomer phenylhydroquinone.

Liquid crystalline polymer as a processing agent in blends of poly(ether-ketone)/LCP70

Blends of a liquid crystalline thermotropic copolyester (LCP70) and an amorphous phenolphthalein based poly(ether-ketone)(PEK-C) with two viscosities were prepared by melt blending. The blends' morphology, rheological and mechanical properties were investigated by DSC, SEM, mechanical and rheological tests. It was observed that the optimum composition of the PEK-C/LCP70 blend was 10 wt% LCP for both mechanical and rheological properties. When the LCP content was less than 10%, the LCP phase existed as finely dispersed fibrous domains with a diameter of about 1 mu m in the matrix, and both tensile and flexural properties were improved. In contrast, when the LCP content reached 20% or more, the LCP domains coalesced to ellipsoidal particles with a diameter of about 5 mu m, and the mechanical properties decreased as a result. It is demonstrated that pure PEK-C with a high viscosity which was difficult to process by melt extrusion, could be extruded conveniently when 10% LCP70 was incorporated. It is emphasized that LCP not only can be used as a reinforcing phase but also an effective processing agent for engineering thermoplastics, especially for those with high viscosity and narrow processing window. (C) 1997 Elsevier Science Ltd.

LIQUID-CRYSTALLINE POLYSURFACTANT

A new kind of amphiphilic polymer(PAMC(16)B) has been synthesized where the amphiphilic moiety is attached as a side chain via the hydrophilic end to the polymer backbone. DSC, POM, and WAXD study revealed that the polysurfactant formed thermotropic liquid crystalline phase. The liquid crystalline domains appeared after annealed at the melt for a period of time, and evolved with annealing. It was indicated that the thermodynamic effect played a significant role on the self-aggregation of hydrophobic ends, so as to form liquid crystalline structure. X-ray investigation suggested that the mesophase structure could be described as smectic with lamellar type of packing, in which alkyl tails aggregated to form layer, A model of supermolecular structure was given.

ELECTRON-DIFFRACTION STUDY ON MONOLAYER LB FILMS OF LIQUID-CRYSTALLINE POLYACRYLATE CONTAINING PARA-NITRO AZOBENZENE

Monolayers of liquid-crystalline polyacrylate containing para-nitro azobenzene (HP6) on the water subphase were characterized by the surface pressure (pi)-area per monomer unit (A) isotherm and were successfully transferred onto glass substrates by the vertical lifting method. The monolayer Langmuis-Blodgett (LB) films transferred at different surface pressures were studied by electron diffraction. The thickness of the monolayer LB film was measured by the transmission electron microscopy folding method. The results of the electron diffraction of the monolayer LB films of HP6 showed that a two-dimensional arrangement exists in the transferred films. According to the results of the pi-A isotherm, electron diffraction and the measured thickness of the monolayer LB film, a molecular arrangement model of HP6 on the water subphase was proposed. The ordered monolayer formation of HP6 showed it to be promising as a second-order non-linear optical material.

ULTRASTRUCTURE OF LIQUID-CRYSTALLINE POLYACRYLATES CONTAINING P-NITRO AZOBENZENE

The phase behaviour ai the side chain liquid crystalline polyacrylates containing p-nitro azobenzene was studied bg DSC, WAXD and the polarized optical microscopy. It was shown that nematic phase can be formed for homopolymer HP6, no LC phase can be observed for HF3 and HP4; whereas smectic S-Ad phase can be obtained tor P-n when n was equal to 3,4, 6,8. The unique phase behaviour of the copolymers P-n was due to the existence of H bond between -COOH and -NO2 which lias been confirmed by FTIR. The molecular arrangement of the copolymers in their LC states was proposed from the results of WAXD and FTIR.

Synthesis and properties of thermotropic liquid crystalline copolyesters containing bis(4-hydroxyphenyl)methanone(V)

A new series of fully aromatic thermotropic liquid crystalline copolyesters were synthesized by thermal polycondensation of p-hydroxybenzoic acid (PHB), terephthalic acid (TPA), resorcinol (RES) and bis (4-hydroxyphenyl) methanone (BHP). The DSC traces of copolyesters exhibited two or three endotherms, the low temperature endotherm(Tm) of which indicated the transition from solid state to anisotropic phase. Observation under polarizing microscope and WAXD measurements suggested that the LC-phase formed immediately above Tm had a nematic character.

Synthesis and properties of thermotropic liquid crystalline copolyesters containing bis(4-hydroxyphenyl)methanone(IV)

A series of thermotropic liquid crystalline copolyesters were synthesized by thermal polycondensation of p-hydroxybenzoic acid, terephthalic acid, bis (4-hydroxyphenyl) methanone and diols. The resulting copolyesters were characterized by WAXD,DSC and PLM. All the copolyesters formed a nematic phase.

FRACTURE-TOUGHNESS AND MORPHOLOGY OF PHENOLPHTHALEIN POLY(ETHER SULFONE) THERMOTROPIC LIQUID-CRYSTALLINE POLYMER BLENDS

Blends of a new phenolphthalein poly (ether sulfone) (PES-C) and a thermotropic liquid crystalline polymer (LCP) were prepared by melt-blending in a twin-screw extruder. Rheological properties, fracture toughness, K(IC), and morphology of the blends were