Remote sensing enhanced motor vehicle emissions control for pollution reduction in the Chicago metropolitan area : siting and issue analysis : final report /

"Project: 90/009."

Direct support and general support maintenance manual for control, remote switchboard C-10333/TTC-39 (V).

"29 April 1983."

Development and validation of the Multiple Remote Tower (MRT) for remote air traffic control

The symbol in air traffic control (ATC), essentially unchanged since the beginning of commercial air traffic early last century, is the characteristic control tower with its large, tilted windows, situated at an exposed location, and rising high above the airport. “Remote Tower” is changing the provision of Air Traffic Services (ATS) in a way that it is more service tailored, dynamically located and available when and where needed, enabled by digital solutions replacing the physical presence of controllers and control towers at aerodromes with a remotely provided Air Traffic Service for Multiple Aerodromes. The paper examines this phenomenon that will mark an epochal change, analysing the experiments and validations carried out in the last years.

Cost effectiveness of OptiMal (R) rapid diagnostic test for malaria in remote areas of the Amazon Region, Brazil

Background: In areas with limited structure in place for microscopy diagnosis, rapid diagnostic tests (RDT) have been demonstrated to be effective. Method: The cost-effectiveness of the Optimal (R) and thick smear microscopy was estimated and compared. Data were collected on remote areas of 12 municipalities in the Brazilian Amazon. Data sources included the National Malaria Control Programme of the Ministry of Health, the National Healthcare System reimbursement table, hospitalization records, primary data collected from the municipalities, and scientific literature. The perspective was that of the Brazilian public health system, the analytical horizon was from the start of fever until the diagnostic results provided to patient and the temporal reference was that of year 2006. The results were expressed in costs per adequately diagnosed cases in 2006 U. S. dollars. Sensitivity analysis was performed considering key model parameters. Results: In the case base scenario, considering 92% and 95% sensitivity for thick smear microscopy to Plasmodium falciparum and Plasmodium vivax, respectively, and 100% specificity for both species, thick smear microscopy is more costly and more effective, with an incremental cost estimated at US$ 549.9 per adequately diagnosed case. In sensitivity analysis, when sensitivity and specificity of microscopy for P. vivax were 0.90 and 0.98, respectively, and when its sensitivity for P. falciparum was 0.83, the RDT was more cost-effective than microscopy. Conclusion: Microscopy is more cost-effective than OptiMal (R) in these remote areas if high accuracy of microscopy is maintained in the field. Decision regarding use of rapid tests for diagnosis of malaria in these areas depends on current microscopy accuracy in the field.

Microcirculatory effects of local and remote ischemic preconditioning in supraceliac aortic clamping

Introduction: Supraceliac aortic clamping in major vascular procedures promotes splanchnic ischemia and reperfusion (I/R) injury that may induce endothelial dysfunction, widespread inflammation, multiorgan dysfunction, and death. We tested the hypothesis that local or remote ischemic preconditioning (IPC) may be protective against injury after supraceliac aortic clamping through the modulation of mesenteric leukocyte-endothelial interactions, as evaluated with intravital microscopy and expression of adhesion molecules. Methods: Fifty-six male Wistar rats (weight, 190 to 250 g), were divided into four groups of 14 rats each: control sham surgery without aortic occlusion; I/R through supraceliac aortic occlusion for 20 minutes, followed by 120 minutes of reperfusion; local IPC through supraceliac aortic occlusion for two cycles of 5 minutes of ischemia and 5 minutes of reperfusion, followed by the same protocol of the IR group; remote IPC through infrarenal aortic occlusion for two cycles of 10 minutes of ischemia and 10 minutes of reperfusion, followed by the same protocol of the IR group. Seven animals per group were used to evaluate in vivo leukocyte-endothelial interactions in postcapillary venules with intravital microscopy and another seven animals per group were used to collect mesentery samples for inmmnohistochemistry demonstration of adhesion molecules expression. Results: Supraceliac aortic occlusion increased the number of rolling leukocytes with slower velocities and increased the number of adherent leukocytes to the venular surface and leukocyte migration to the interstitium. The expression of P-selectin, E-selectin, and intercellular adhesion molecule-1 was also increased significantly after I/R. Local or remote IPC reduced the leukocyte recruitment in vivo and normalized the expression of adhesion molecules. Conclusions: Local or remote IPC reduces endothelial dysfunction on mesenteric microcirculation caused by I/R injury after supraceliac aortic clamping. (J Vase Surg 2010;52:1321-9.) Clinical Relevance: The present study demonstrates that ischemia and reperfusion injury induced by supraceliac aortic occlusion promotes endothelial dysfunction and leukocyte recruitment on mesenteric microcirculation. Local and remote preconditioning reduced leukocyte-endothelial interactions and normalized the expression of endothelial adhesion molecules involved in this process. Although we recognize the limitation of an experimental model, our findings suggest that local and remote ischemic preconditioning minimize the endothelial dysfunction and leukocyte recruitment events that play a central role in systemic inflammation and multiorgan dysfunction after major aortic reconstructions.

Self-Directed Behavioral Family Intervention for Parents of Oppositional Children in Rural and Remote Areas

Twenty-four parents of oppositional preschoolers were randomly assigned to either a self-directed behavioral family intervention condition (SD) or to a waitlist control group (WL). The self-directed parent training program based on self-regulation principles, consisted of a written information package and weekly telephone consultations for 10 weeks. At posttest, in comparison to the WL group, children in the SD group had lower levels of behavior problems on parent report measures of child behavior. At posttreatment, parents in the SD condition reported increased levels of parenting competence and lower levels of dysfunctional parenting practices as compared to parents in the WL condition. In addition, mothers reported lower levels of anxiety, depression, and stress as compared to mothers in the WL condition at posttreatment. Using mother's reports, gains in child behavior and parenting practices achieved at posttreatment were maintained at 4-month follow-up.

Effects of Partial Liver Ischemia Followed by Global Liver Reperfusion on the Remote Tissue Expression of Nitric Oxide Synthase: Lungs and Kidneys

Hepatic ischemia followed by reperfusion (IR) results in mild to severe remote organ injury. Oxidative stress and nitric oxide (NO) seem to be involved in the IR injury. Our aim was to investigate the effects of liver I/R on hepatic function and lipid peroxidation, leukocyte infiltration and NO synthase (NOS) immunostaining in the lung and the kidney. We randomized 24 male Wistar rats into 3 groups: 1) control; 2) 60 minutes of partial (70%) liver 1 and 2 hours of global liver R; and 3) 60 minutes of partial (70%) liver I and 6 hours of global liver R. Groups 2 and 3 showed significant increases in plasma alanine and aspartate aminotransferase levels and in tissue malondialdehyde and myeloperoxidase contents. In the kidney, positive endothelial NOS (eNOS) staining was significantly decreased in group 3 compared with group 1. However, staining for inducible NOS (iNOS) and neuronal NOS (nNOS) did not differ among the groups. In the lung, the staining for eNOS and iNOS did not show significant differences among the groups; no positive nNOS staining was observed in any group. These results suggested that partial liver I followed by global liver R induced liver, kidney, and lung injuries characterized by neutrophil sequestration and increased oxidative stress. In addition, we supposed that the reduced NO formation via eNOS may be implicated in the moderate impairment of renal function, observed by others at 24 hours after liver I/R.

Remote probe microphone measurement to verify hearing aid performance

We assessed the feasibility of obtaining probe microphone measurements of hearing aids at a distance. Face-to-face and remote probe microphone measurements were carried out in 60 hearing aid users (mean age 67 yrs) with uni- or bilateral hearing losses (105 ears tested). The participant and a facilitator were located in a room equipped with a probe microphone system interfaced to a PC. Desktop videoconferencing and application sharing was used to allow an audiologist in another room to instruct the facilitator and control the equipment via the LAN. There were significant correlations between face-to-face and remote real ear unaided response (REUR), aided response (REAR) and insertion gain (REIG) at seven discrete frequencies from 250 to 6000 Hz. Differences between face-to-face and remote responses were within the reported variability for probe microphone measurements themselves. The results show that remote probe microphone measurements are feasible and might improve the quality of public hearing aid services and professional training in Brazil.

The AIDS epidemic in the Amazon region: a spatial case-control study in Rondonia, Brazil

OBJECTIVE To analyze spatial changes in the risk of AIDS and the relationship between AIDS incidence and socioeconomic variables in the state of Rondonia, Amazon region. METHODS A spatial, population case-control study in Rondonia, Brazil, based on 1,780 cases reported to the Epidemiological Surveillance System and controls based on demographic data from 1987 to 2006. The cases were grouped into five consecutive four-year periods. A generalized additive model was adjusted to the data; the dependent variable was the status of the individuals (case or control), and the independent variables were a bi-dimensional spline of the geographic coordinates and some municipality-level socioeconomic variables. The observed values of the Moran’s I test were compared to a reference distribution of values generated under conditions of spatial randomness. RESULTS AIDS risk shows a marked spatial and temporal pattern. The disease incidence is related to socioeconomic variables at the municipal level in Rondônia, such as urbanization and human capital. The highest incidence rates of AIDS are in municipalities along the BR-364 highway and calculations of the Moran’s I test show positive spatial correlation associated with proximity of the municipality to the highway in the third and fourth periods (p = 0.05). CONCLUSIONS Incidence of the disease is higher in municipalities of greater economic wealth and urbanization, and in those municipalities bisected by Rondônia’s main roads. The rapid development associated with the opening up of once remote regions may be accompanied by an increase in these risks to health.

Using remote labs in education: two little ducks in remote experimentation

A book about remote labs and engineering education begs to begin with the question, “Why do engineering programs include lab work?” Although this may seem like a given and not worth discussing, whenever we’re faced with innovative ideas, it’s important to “put everything on the table” in order to reassess its value to our program or goals. What is it about lab work that is of value to students? Are there elements of traditional labs that we could let go of? Are there elements that we don’t want to lose? These questions can help us to clarify how and why labs are integrated into an engineering education program.

An integrated reusable remote laboratory to complement electronics teaching

The great majority of the courses on science and technology areas where lab work is a fundamental part of the apprenticeship was not until recently available to be taught at distance. This reality is changing with the dissemination of remote laboratories. Supported by resources based on new information and communication technologies, it is now possible to remotely control a wide variety of real laboratories. However, most of them are designed specifically to this purpose, are inflexible and only on its functionality they resemble the real ones. In this paper, an alternative remote lab infrastructure devoted to the study of electronics is presented. Its main characteristics are, from a teacher's perspective, reusability and simplicity of use, and from a students' point of view, an exact replication of the real lab, enabling them to complement or finish at home the work started at class. The remote laboratory is integrated in the Learning Management System in use at the school, and therefore, may be combined with other web experiments and e-learning strategies, while safeguarding security access issues.

A remote engineering solution for automating a roller hearth kiln

Remote engineering (also known as online engineering) may be defined as a combination of control engineering and telematics. In this area, specific activities require computacional skills in order to develop projects where electrical devives are monitored and / or controlled, in an intercative way, through a distributed network (e.g. Intranet or Internet). In our specific case, we will be dealing with an industrial plant. Within the last few years, there has been an increase in the number of activities related to remote engineering, which may be connected to the phenomenon of the large extension experienced by the Internet (e.g. bandwith, number of users, development tools, etc.). This increase opens new and future possibilities to the implementation of advance teleworking (or e-working) positions. In this paper we present the architecture for a remote application, accessible through the Internet, able to monitor and control a roller hearth kiln, used in a ceramics industry for firing materials. The proposed architecture is based on a micro web server, whose main function is to monitor and control the firing process, by reading the data from a series of temperature sensors and by controlling a series of electronic valves and servo motors. This solution is also intended to be a low-cost alternative to other potential solutions. The temperature readings are obtained through K-type thermopairs and the gas flow is controlled through electrovalves. As the firing process should not be stopped before its complete end, the system is equipped with a safety device for that specific purpose. For better understanding the system to be automated and its operation we decided to develop a scale model (100:1) and experiment on it the devised solution, based on a Micro Web Server.

A smart layer for remote laboratories

Commonly, when a weblab is developed to support remote experiments in sciences and engineering courses, a particular hardware/software architecture is implemented. However, the existence of several technological solutions to implement those architectures difficults the emergence of a standard, both at hardware and software levels. While particular solutions are adopted assuming that only qualified people may implement a weblab, the control of the physical space and the power consumption are often forgotten. Since controlling these two previous aspects may increase the quality of the weblab hosting the remote experiments, this paper proposes the useof a new layer implemented by a domotic system bus with several devices (e.g. lights, power sockets, temperature sensors, and others) able to be controlled through the Internet. We also provide a brief proof-of-concept in the form of a weblab equipped with a simple domotic system usually implemented in smart houses. The added value to the remote experiment hosted at the weblab is also identified in terms of power savings and environment conditions.

A mobile robot platform for open learning based on serious games and remote laboratories

Within the pedagogical community, Serious Games have arisen as a viable alternative to traditional course-based learning materials. Until now, they have been based strictly on software solutions. Meanwhile, research into Remote Laboratories has shown that they are a viable, low-cost solution for experimentation in an engineering context, providing uninterrupted access, low-maintenance requirements, and a heightened sense of reality when compared to simulations. This paper will propose a solution where both approaches are combined to deliver a Remote Laboratory-based Serious Game for use in engineering and school education. The platform for this system is the WebLab-Deusto Framework, already well-tested within the remote laboratory context, and based on open standards. The laboratory allows users to control a mobile robot in a labyrinth environment and take part in an interactive game where they must locate and correctly answer several questions, the subject of which can be adapted to educators' needs. It also integrates the Google Blockly graphical programming language, allowing students to learn basic programming and logic principles without needing to understand complex syntax.

Remote and mobile experimentation: pushing the boundaries of an ubiquitous learning place

Concepts like E-learning and M-learning are changing the traditional learning place. No longer restricted to well-defined physical places, education on Automation and other Engineering areas is entering the so-called ubiquitous learning place, where even the more practical knowledge (acquired at lab classes) is now moving into, due to emergent concepts such as Remote Experimentation or Mobile Experimentation. While Remote Experimentation is traditionally regarded as the remote access to real-world experiments through a simple web browser running on a PC connected to the Internet, Mobile Experimentation may be seen as the access to those same (or others) experiments, through mobile devices, used in M-learning contexts. These two distinct client types (PCs versus mobile devices) pose specific requirements for the remote lab infrastructure, namely the ability to tune the experiment interface according to the characteristics (e.g. display size) of the accessing device. This paper addresses those requirements, namely by proposing a new architecture for the remote lab infrastructure able to accommodate both Remote and Mobile Experimentation scenarios.