Production of Ti-6Al-4V billet through compaction of blended elemental powders by equal-channel angular pressing

In this work, compaction by warm equal-channel angular pressing (ECAP) with back pressure was used to produce Ti-6Al-4V billets from both commercially pure (CP) titanium and titanium hydride (TiH 2) powders, which were mixed with pulverised binary Al-V master alloys of two distinct Al/V ratios and with elemental aluminium powder to arrive at the nominal alloy composition. It was demonstrated that the right combination of temperature, high hydrostatic pressure and plastic shear deformation permits consolidation of the powder mixture to maximum green densities of 99.26%. Moreover, after direct compaction of blended elemental powders by equal-channel angular pressing (ECAP) with back pressure, the sintering temperature required for chemical and microstructural homogenisation of the compacts could be reduced by 150-250°C. This was possible due to high green density, increased contact area between powder particles and the formation of fast diffusion paths associated with grain refinement by severe plastic deformation. The sintered Ti-6Al-4V billets exhibited a maximum density of 99.88%, Vickers hardness of 409-445 HV1 and ultimate tensile strength in the range of 1000-1080MPa. In contrast to findings of other authors, the use of TiH 2 powders in conjunction with ECAP processing did not bring any benefits with regard to the production of the Ti-6Al-4V alloy.

Effect of back pressure during equal-channel angular pressing on deformation-induced porosity in copper

The effect of back pressure during equal channel angular pressing (ECAP) on deformation-induced porosity is investigated. While percolating porosity was found after 4 ECAP passes in the absence of back pressure, no percolation was detected when a back pressure of 200 MPa was applied. However, after ECAP with back pressure continued to 8 passes, percolating porosity did appear. The nature of the percolating porosity developed in severely deformed materials is discussed.

Sustainable population health : a pressing priority for community wellbeing

Recent developments in primary health care, preventive care, early intervention programs, population health constructs and coordinated care trials in Australia have explored the idea of changing our emphasis in health care from responsive acute care to more integrated, whole population community wellbeing management. This idea accepts that much illness and even trauma experienced by individuals in our communities can be prevented, mitigated or managed in a more constructive and positive manner than has previously been the case. Much disabling illness need not occur at all and can be avoided through better community based management models, education programs, and lifestyle changes that contribute to more healthy communities. As in the wider business world, we are becoming more cognisant of the fact that prevention is not only an appealing idea in terms of health outcomes and quality of life, but that it is good for business also. It can moderate demand for costly health care, assist consumers to understand how to live healthier and fulfilling lives and overall help to sustain a much more dynamic community. This article, based on work in a rural health service in South Australia, points to some elements of sustainable primary care that appear to have potential to take us where we need to go. It asks whether we have the capacity and the will to make the necessary investment in sustainability to ensure our future or whether we are to remain bound in a reactionary model of health care rather than considering the impact of wider social and physical environments as part of the overall community health equation.

Multicomponent materials from machining chips compacted by equal-channel angular pressing

Al and Mg machining chip blends were compacted by equal-channel angular pressing with back pressure. By varying the weight fraction of the constituent materials, temperature and processing route, as well as employing subsequent heat treatment, the microstructure and the mechanical properties of the compact were varied. The width of the interdiffusion zone and the formation of intermetallic phases near the interfaces between the two metals were studied by energy-dispersive X-ray spectroscopy and nanoindentation. It was shown that substantial improvement of mechanical properties, such as an increase of strength, strain-hardening capability and ductility, can be obtained. This is achieved by changing the processing parameters of equal-channel angular pressing and the annealing temperature, as well as by optimising the weight fraction of the constituent metals. © 2013 Springer Science+Business Media New York.

Effect of counterpressure during equal-channel angular pressing on nanoporosity formation in ultrafine-grained copper

Results of small-angle X-ray scattering and high-precision density measurements showed that the application of counterpressure during the equal-channel angular pressing (ECAP) of ultrafine-grained copper leads to a decrease in nanoporosity and an increase in mechanical properties of the ECAP-processed metal.

Equal-channel angular pressing and annealing of a twinning-induced plasticity steel : microstructure, texture, and mechanical properties

In this work, a high-manganese Fe-23Mn-1.5Al-0.3C Twinning-Induced Plasticity (TWIP) steel was subjected to plastic shear deformation using Equal-Channel Angular Pressing (ECAP) at 300 °C following route BC and additional annealing. The microstructure evolution during both deformation by ECAP and subsequent annealing was investigated and correlated with the mechanical properties. The successive grain refinement during ECAP was promoted by two parallel mechanisms, namely dislocation driven grain fragmentation and twin fragmentation, and accounted for the ultra-high strength. In addition, due to the relatively low volume fraction of deformation twins after ECAP at 300 °C, further contribution of deformation twinning during room temperature deformation allowed additional work-hardening capacity and elongation. During subsequent recovery annealing the ultra-fine grains and deformation twins were thermally stable, which supported retainment of the high yield strength along with regained uniform elongation. For the first time, the texture evolution during ECAP and during the following heat treatment was analyzed. After 1, 2, and 4 ECAP passes a transition texture with the characteristic texture components of both high- and low-SFE materials developed. During the following heat treatment the texture evolution proceeded similar to that observed in the same material after cold rolling. Retaining of the ECAP texture components due to oriented nucleation at grain boundaries and triple junctions as well as annealing twinning accounted for the formation of a weak, retained ECAP texture after recrystallization.

Evolution of nanoscale porosity during equal-channel angular pressing of titanium

Small-angle neutron scattering (SANS) analysis and transmission electron microscopy evidence suggest the occurrence of nanoscale porosity in commercial-purity titanium processed by equal-channel angular pressing (ECAP). SANS data were produced at two different facilities (GKSS, Germany; and Los Alamos, USA) and were analysed using three different methods. The results are consistent and yield a conclusive picture of the distribution of the scattering centres, which are believed to be associated with nanoporosity. Back pressure applied during ECAP tends to reduce the average pore size, which also depends on the processing route used. The results of the study strongly suggest that ECAP leaves a footprint in titanium in the form of a population of polydispersed nanovoids, which may play an important role in subsequent processing of the material.

Improving hydrogen storage properties of magnesium based alloys by equal channel angular pressing

Equal channel angular pressing was applied to a commercial magnesium alloy ZK60 in order to improve its hydrogen storage properties. The microstructure refinement and increase in the density of crystal lattice defects caused by equal channel angular pressing increase hydrogen desorption pressure, change the slope of the pressure plateau in pressure-composition isotherms, decrease the pressure hysteresis, and accelerate the hydrogen desorption kinetics. It is argued that a proper design of the defect structure of materials is a key element in the search for economically viable and environmentally acceptable solutions for mobile hydrogen storage based on metal hydrides.

Non-equal channel angular pressing of aluminum alloy

Strain history, microstructure and texture were studied in an aluminum alloy processed by the recently proposed process of non-equal channel angular pressing (NECAP). Comparison with alloy processed by equal channel angular pressing (ECAP) has been performed. A much finer microstructure was obtained in NECAP, showing that in this modified ECAP test the grain-refinement process was more efficient. The results indicate that the NECAP test has some interesting features that may be of interest for further research.

Strain localisation patterns under equal-channel angular pressing

Instabilities of plastic flow in the form of localised shear bands were experimentally observed to result from equal-channel angular pressing (ECAP) of magnesium alloy AZ31. The appearance of shear bands and their spacing were dependent on velocity of the pressing and applied back-pressure. A generic gradient plasticity theory involving second-order strain gradient terms in a constitutive model was applied to the case of AZ31 deformed by ECAP. Linear stability analysis was applied to the set of equations describing the deformation behaviour in the process zone idealised as a planar shear zone. A full analytical solution providing a dispersion relation between the rate of growth of a perturbation and the wave number was obtained. It was shown that the pattern of incipient localised shear bands exhibits a spectrum of characteristic lengths corresponding to admissible wave numbers. The interval of the spectrum of wave numbers of viable, i.e. growing, perturbations predicted by linear stability analysis was shown to be in good agreement with the experimentally observed spectrum. The effect of back-pressure applied during ECAP was also considered. The predicted displacement of the shear band spectrum towards lower wave numbers, shown to be a result of the decreased shear strain rate in the shear zone, was consistent with the experimentally observed increase of the band spacing with increased back-pressure. A good predictive capability of the general modelling frame used in conjunction with linear stability analysis was thus demonstrated in the instance of the particular alloy system and the specific processing conditions considered.

Effect of processing parameters on the magnetic properties and macrotexture of a Nd13.5Fe73.8Co6.7B5.6Ga0.4 alloy processed by equal channel angular pressing with back pressure

Equal channel angular pressing (ECAP) is a well-established thermo-mechanical processing technique, which could induce the c-axis texture of Nd2Fe14B in a melt-spun Nd13.5Fe73.8Co6.7B5.6Ga0.4 alloy. However, the effects of ECAP processing parameters, such as temperature, back pressure (BP), and multiple-pass ECAP routes, remain unknown for this alloy. In this paper, we have investigated the effects of these processing parameters on the c-axis texture formation. It is found by X-ray diffraction macrotexture analysis that the maximum intensity of (001) pole figures for the tetragonal-Nd2Fe14B phase (Imax) shows an increase from 2.7 to 4.1 m.r.d. (multiples of random distribution) by increasing the ECAP temperature from 723 to 823 K, while the difference in remanent magnetization between easy and hard directions (Δ Mr) rises from 24.0 to 41.5 Am2/kg. When the BP was increased from 0.25 to 0.5 GPa at 823 K, Imax showed an increase from 2.8 to 4.1 m.r.d. However, Imax saturated for BPs above 0.5 GPa, suggesting that BP has limited effect on the texture formation, although it is necessary for the compaction of the alloy powders. Two multiple-pass ECAP routes conventionally known as routes A and C were employed for two-pass ECAP at 823 K. It is found that route A processing is effective in enhancing the texture formation, while the texture is lost by a subsequent pressing when adopting route C. Therefore, the compaction of Nd13.5Fe73.8Co6.7B5.6Ga0.4 alloy powder using route A ECAP passes with 0.5 GPa BP at 823 K results in pronounced texture, which is beneficial for anisotropic hard magnetic properties.

Why fundamentalism?

Why Fundamentalism? was an exhibition proposal and critical writing project developed from concept phase through to detailed proposal. It included an edited video document that lay out its core ideas and presented the diverse voices of each collaborator. A number of key themes were engaged around the hot-button (and much misunderstood) concept of Fundamentalism. The proposal included an exhibition layout, developed test imagery, ideas and animations, proposed forms for future works and a process whereby design briefs would lead to subsequent commissions. Two major grant applications were submitted to the Australia Council and Arts Queensland, with the support of State Library of Queensland, the University of Adelaide and numerous others. The project remains at the developed proposal stage awaiting suitable funding----- Critically the show became an active vehicle for drawing and exploring a line of distinction between ideas of ‘what is fundamental’ and ‘fundamentalism’ as it rested in the popular imagination, as well as in political and philosophical debates. It teased out and engaged with a number of key questions that included The Problem of Ungroundedness, A Politics of Finitude, The Post-modern/Pluralist Problem, Silent Fundamentalisms (Voices of Reason and Neo-con Religions), Fundamentalism as a Media Construct, The Pre and Post Cold-war Other, The Pressing Need for Foundations in the West and Islam as Foundationalism (rather than fundamentalism).

Equal employment opportunity and diversity management : can either live up to the promise of achieving gender equity?

This paper examines the extent to which women movement into management positions. Like many other countries, this progress in Australia is slow. The paper includes discussion of the theoretical explanations for this and the extent to which these are borne out in Australia. We are aware this group represents only a minority of Australian women workers, and there are many other groups of women workers for whom constraints to women’s access to senior management may not be the most pressing issue. We have, however, chosen to focus on women in management in this paper, as while there was considerable research and public policy attention directed towards this group in the 1980s and early 1990s, over the past decade there seems to have been a reluctance to continue to address this group, despite the numerical evidence that women continue to be disproportionately represented in senior management positions. We believe it’s timely to refocus on women in management.

Australia : LIS education

The topic of library and information science (LIS) education has been under the spotlight in the professional literature in Australia and New Zealand for a number of years. Critical issues of discussion encompass the apparent lack of a core curriculum for the discipline, the perceived gulf between LIS education and LIS practice, and the pressing need for career-long learning and development. One of the central points of debate that emerges repeatedly is the long-standing question about the positioning of the profession: Is LIS a graduate profession of highly skilled individuals valued for their expertise and professionalism or is it a profession of anyone who works in a library, regardless of their qualifications (LIANZA, 2005)? While Australia and New Zealand do not stand alone in this debate – similar issues are echoed in many other countries – there are inevitably some local characteristics which warrant exploration. The discussion presented here highlights the historical background to professional training, the specific professional policies and standards that guide LIS education and some of the challenges facing professional and paraprofessional education, given the changing environment of education in Australia as a whole, with some comparisons made with the New Zealand situation. While all too often library practitioners point the finger at the library educators to ‘right the wrongs’, the authors wish to reinforce the idea that the future of effective and relevant LIS education is a matter for all stakeholders in the profession: practitioners and educators, students and staff, employers and employees, with cohesion potentially offered by the professional body.

Duplicity/complicity : misperforming the social drama of disability

In this paper, I investigate the (mis)performance of ‘passing’ in the context of bodies with disabilities. The desire to conceal, control or contain a body’s idiosyncrasies can be a deceitful act, complicit with dominant cultural assumptions about the benefits of fitting in. Passing, and the performative tricks, techniques and prostheses that support the ‘lie’ of passing, upholding a social contract in which a closeting-as-cure approach accommodates discomfort with difference. In this paper, I consider moments of non-passing, where people are caught out by mistakes or deliberate misperformances of the daily social drama of ability and disability. I reference the work of disabled artists Bill Shannon, Aaron Williamson and Katherine Araniello, who re-perform their daily personal interactions in the public sphere as a sort of guerilla theatre. Their work brings hidden assumptions about how disabled people should act and interact to the brink of visibility. It challenges passers-by to confront their complicity in these discourses by pressing them to re-perform their own spontaneous reactions to bodies that misperform the ‘lie’ of normalcy.