Studies of ambient organic and inorganic aerosol in Southern California

The negative impacts of ambient aerosol particles, or particulate matter (PM), on human health and climate are well recognized. However, owing to the complexity of aerosol particle formation and chemical evolution, emissions control strategies remain difficult to develop in a cost effective manner. In this work, three studies are presented to address several key issues currently stymieing California's efforts to continue improving its air quality.

Gas-phase organic mass (GPOM) and CO emission factors are used in conjunction with measured enhancements in oxygenated organic aerosol (OOA) relative to CO to quantify the significant lack of closure between expected and observed organic aerosol concentrations attributable to fossil-fuel emissions. Two possible conclusions emerge from the analysis to yield consistency with the ambient organic data: (1) vehicular emissions are not a dominant source of anthropogenic fossil SOA in the Los Angeles Basin, or (2) the ambient SOA mass yields used to determine the SOA formation potential of vehicular emissions are substantially higher than those derived from laboratory chamber studies. Additional laboratory chamber studies confirm that, owing to vapor-phase wall loss, the SOA mass yields currently used in virtually all 3D chemical transport models are biased low by as much as a factor of 4. Furthermore, predictions from the Statistical Oxidation Model suggest that this bias could be as high as a factor of 8 if the influence of the chamber walls could be removed entirely.

Once vapor-phase wall loss has been accounted for in a new suite of laboratory chamber experiments, the SOA parameterizations within atmospheric chemical transport models should also be updated. To address the numerical challenges of implementing the next generation of SOA models in atmospheric chemical transport models, a novel mathematical framework, termed the Moment Method, is designed and presented. Assessment of the Moment Method strengths and weaknesses provide valuable insight that can guide future development of SOA modules for atmospheric CTMs.

Finally, regional inorganic aerosol formation and evolution is investigated via detailed comparison of predictions from the Community Multiscale Air Quality (CMAQ version 4.7.1) model against a suite of airborne and ground-based meteorological measurements, gas- and aerosol-phase inorganic measurements, and black carbon (BC) measurements over Southern California during the CalNex field campaign in May/June 2010. Results suggests that continuing to target sulfur emissions with the hopes of reducing ambient PM concentrations may not the most effective strategy for Southern California. Instead, targeting dairy emissions is likely to be an effective strategy for substantially reducing ammonium nitrate concentrations in the eastern part of the Los Angeles Basin.

HYBRID PHOTOVOLTAIC DEVICES BASED ON ORGANIC SEMICONDUCTING POLYMERS AND INORGANIC NANOSTRUCTURED ELECTRODES

La fotovoltaica orgánica es una tecnología solar emergente que todavía no ha entrado en el mercado. El objetivo de esta tesis ha sido acercar un poco más la industrialización de dicha tecnología mediante el incremento de la eficiencia y la durabilidad de estos dispositivos solares. Para la consecución de dicho objetivo se identificaron las limitaciones existentes y se diseñó una hora de ruta con diversas estrategias para poder superar cada uno de los problemas. Así, mediante un exhaustivo control de la nano morfología del film fotoactivo y la introducción de electrodos nanoestructurados se ha conseguido incrementar la eficiencia. La sustitución de los electrodos estándares por nuevos electrodos basados en óxidos metálicos confiere durabilidad al sistema. Por último, la sustitución del óxido de indio y estaño como electrodo transparente por nanohilos metálicos de plata habilita la posibilidad de fabricar dispositivos solares flexibles de bajo coste.

Laboratory culture of Moina with organic ana inorganic fertilizers

An experiment was conducted in the laboratory condition to determine the effect of organic (poultry drop, cow dung and mustard oil cake) and inorganic fertilizer (urea) on production, reproduction rate and maturation time of Moina species. Production rate was also determined in both aerated and non-aerated system in plastic containers with carrying capacity of 2.5-liter each. Total production was significantly higher in both aerated (2475 individuals/2.5 l water) and non-aerated (3253 individuals/2.5 l water) containers using poultry manure compared to other fertilizers. Moreover, the reproduction rate and maturation time in poultry drops showed distinct efficacy in Moina species. Reproduction rate of 11 individuals was the maximal while lowest maturation time was found 78 hours. Reproduction and maturation were induced surprisingly in test tube where the aeration system was absent.

Fabrication of ZnO and its enhancement of charge injection and transport in hybrid organic/inorganic light emitting devices

ZnO nanocrystals were synthesized by hydrolysis in methanol. X-ray diffraction and photoluminescence spectra confirm that good crystallized ZnO nanoparticles were formed. Utilizing those ZnO nanoparticles and poly [2- methoxy-5 - (3',7'-dimethyloctyloxy)- 1,4-phenylenevinylene] (MDMO-PPV), light emitting devices with indium tin oxide (ITO)/poly(3,4-oxyethyleneoxy-thiophene):poly(styrene sulfonate) (PEDOT:PSS)/ ZnO:MDMO-PPV/Al and ITO/PEDOT:PSS/MDMO-PPV/Al structures were fabricated. Electrolummescence (EL) spectra reveal that EL yield of hybrid MDMO-PPV and ZnO nanocrystals devices increased greatly as compared with pristine MDMO-PPV devices. The current-voltage characteristics indicate that addition of ZnO nanocrystals can facilitate electrical injection and charge transport. The decreased energy barrier to electron injection is responsible for the increased efficiency of electron injection. (c) 2007 Elsevier B.V. All rights reserved.

Organic/inorganic hybrid solar cells based on SnS/SnO nanocrystals and MDMO-PPV

SnS/SnO heterojunction structured nanocrystals with zigzag rod-like connected morphology were prepared by using a simple two-step method. Bulk heterojunction solar cells were fabricated using the SnS/SnO nanocrystals blended with poly(2-methoxy-5-(3',7'-dimethyloctyloxy)-1,4-phenylene vinylene) (MDMO-PPV) as the active layer. Compared with solar cells using SnS nanoparticles hybridized with MDMO-PPV as the active layer, the SnS/SnO devices showed better performance, with a power conversion efficiency higher by about one order in magnitude.

Synthesis and luminescence properties of hybrid organic-inorganic transparent titania thin film activated by in-situ formed lanthanide complexes

Stable transparent titania thin films were fabricated at room temperature by combining thenoyltrifluoroacetone (TTFA)-modified titanium precursors with amphiphilic triblock poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO, P123) copolymers. The obtained transparent titania thin films were systematically investigated by IR spectroscopy, PL emission and excitation spectroscopy and transmission electron microscopy. IR spectroscopy indicates that TTFA coordinates the titanium center during the process of hydrolysis and condensation. Luminescence spectroscopy confirms the in-situ formation of lanthanide complexes in the transparent titania thin film.

The research of rheology and thermodynamics of organic-inorganic hybrid membrane during the membrane formation

To clarify the mechanism of organic-inorganic hybrid membrane formation by phase-inversion method, the thermodynamical and theological properties of PSF/TiO2 casting solution were investigated by the viscosity measurement and the triangle phase diagram, respectively. TiO2 introduction decreased the non-solvent tolerance of casting solution with non-solvent 20% ethanol aqueous solution, which caused thermodynamic enhancement of phase separation, and also resulted in the change of theological properties from Newtonian fluid to non-Newtonian fluid and the viscosity increase of casting solution, which induced rheological hindrance in demixing process

Controlled synthesis of organic-inorganic hybrid nanofibers by a wet-chemical route

Organic-inorganic hybrid nanofibers are successfully synthesized by incorporating 3,3 ',5,5 '-tetramethylbenzidine (TMB) and H2PtCl6 at room temperature. The morphology and size can be simply controlled by tuning the molar ratio and initial concentration of reactants. A possible formation mechanism was suggested on the basis of the experimental results. The optical properties were investigated and the as-obtained product displays a strong fluorescence emission at room temperature that may be promising for applications in the fabrication of photoelectric materials. (C) 2008 Elsevier B.V. All rights reserved.

New organic-inorganic perovskite materials with different optical properties modulated by different inorganic sheets

New organic-inorganic perovskites with different PbBr perovskite sheets stabilized by 3- or 4-an-tidinopyridine were synthesized and structurally characterized. 4-Amidinopyridine constructs < 001 >-oriented perovskite with inorganic sheets made up of typical corner-sharing octahedra of PbBr2. Analogous chemistry in the presence of 3-amidinopyridine under the same conditions results in an unusual hybrid perovskite with the inorganic sheets showing a novel framework including both corner-sharing and edge-sharing PbBr2, which is different from any previously reported ones.

Organic-inorganic hybrid material for the cells immobilization: Long-term viability mechanism and application in BOD sensors

In this paper, organic-inorganic hybrid material, which is composed of silica and the grafting copolymer of poly (vinyl alcohol) and 4-vinylpyridine (PVA-g-P(4-VP)), was employed to immobilize Trichosporon cutaneum strain 2.570 cells. Cells entrapped into the hybrid material were found to keep a long-term viability. The mechanism of such a long-term viability was investigated by using confocal laser scanning microscopy (CLSM). Our studies revealed that arthroconidia produced in the extracellular material might play an important role in keeping the long-term viability of the immobilized microorganism. After the arthroconidia were activated, an electrochemical biochemical oxygen demand (BOD) sensor based on cell/hybrid material-modified supporting membrane was constructed for verifying the proposed mechanism.