Estudo de reatores eletroquímicos para remoção de Cu2+ , Zn2+, Fenol e BTEX em água produzida

The production of water has become one of the most important wastes in the petroleum industry, specifically in the up stream segment. The treatment of this kind of effluents is complex and normally requires high costs. In this context, the electrochemical treatment emerges as an alternative methodology for treating the wastewaters. It employs electrochemical reactions to increase the capability and efficiency of the traditional chemical treatments for associated produced water. The use of electrochemical reactors can be effective with small changes in traditional treatments, generally not representing a significant additional surface area for new equipments (due to the high cost of square meter on offshore platforms) and also it can use almost the same equipments, in continuous or batch flow, without others high costs investments. Electrochemical treatment causes low environmental impact, because the process uses electrons as reagent and generates small amount of wastes. In this work, it was studied two types of electrochemical reactors: eletroflocculation and eletroflotation, with the aim of removing of Cu2+, Zn2+, phenol and BTEX mixture of produced water. In eletroflocculation, an electrical potential was applied to an aqueous solution containing NaCl. For this, it was used iron electrodes, which promote the dissolution of metal ions, generating Fe2+ and gases which, in appropriate pH, promote also clotting-flocculation reactions, removing Cu2+ and Zn2+. In eletroflotation, a carbon steel cathode and a DSA type anode (Ti/TiO2-RuO2-SnO2) were used in a NaCl solution. It was applied an electrical current, producing strong oxidant agents as Cl2 and HOCl, increasing the degradation rate of BTEX and phenol. Under different flow rates, the Zn2+ was removed by electrodeposition or by ZnOH formation, due the increasing of pH during the reaction. To better understand the electrochemical process, a statistical protocol factor (22) with central point was conducted to analyze the sensitivity of operating parameters on removing Zn2+ by eletroflotation, confirming that the current density affected the process negatively and the flow rate positively. For economical viability of these two electrochemical treatments, the energy consumption was calculated, taking in account the kWh given by ANEEL. The treatment cost obtained were quite attractive in comparison with the current treatments used in Rio Grande do Norte state. In addition, it could still be reduced for the case of using other alternative energy source such as solar, wind or gas generated directly from the Petrochemical Plant or offshore platforms

Ambiente para avaliação de controladores fuzzy aplicados ao método de elevação artificial por bombeio centrífugo submerso

From their early days, Electrical Submergible Pumping (ESP) units have excelled in lifting much greater liquid rates than most of the other types of artificial lift and developed by good performance in wells with high BSW, in onshore and offshore environments. For all artificial lift system, the lifetime and frequency of interventions are of paramount importance, given the high costs of rigs and equipment, plus the losses coming from a halt in production. In search of a better life of the system comes the need to work with the same efficiency and security within the limits of their equipment, this implies the need for periodic adjustments, monitoring and control. How is increasing the prospect of minimizing direct human actions, these adjustments should be made increasingly via automation. The automated system not only provides a longer life, but also greater control over the production of the well. The controller is the brain of most automation systems, it is inserted the logic and strategies in the work process in order to get you to work efficiently. So great is the importance of controlling for any automation system is expected that, with better understanding of ESP system and the development of research, many controllers will be proposed for this method of artificial lift. Once a controller is proposed, it must be tested and validated before they take it as efficient and functional. The use of a producing well or a test well could favor the completion of testing, but with the serious risk that flaws in the design of the controller were to cause damage to oil well equipment, many of them expensive. Given this reality, the main objective of the present work is to present an environment for evaluation of fuzzy controllers for wells equipped with ESP system, using a computer simulator representing a virtual oil well, a software design fuzzy controllers and a PLC. The use of the proposed environment will enable a reduction in time required for testing and adjustments to the controller and evaluated a rapid diagnosis of their efficiency and effectiveness. The control algorithms are implemented in both high-level language, through the controller design software, such as specific language for programming PLCs, Ladder Diagram language.

Competitividade da cadeia produtiva do coco: visão dos extensionistas da EMATER/RN na mesorregião leste Potiguar do Rio Grande do Norte

The present study presents an investigation concerning the factors that, in the perception of the extension of Emater/RN they affect the competitiveness of the productive chain of the coconut in Rio Grande do Norte. For so much it is used of a theory structured starting from the several aspects that delineate the competitiveness and your respective factors, besides the aspects that compose the productive chain of the coconut in Rio Grande do Norte. The research was accomplished at the mesorregião Leste Potiguar of Rio Grande do Norte, territory of larger index of coconut production in the state. The used methodological approach was the one of descriptive exploratory research together to the conduction of a rising type Survey. The field research obtained 35 valid questionnaires, whose interviewees were the extension of Emater/RN in performance in the municipal districts that compose the mesorregião Leste Potiguar of Rio Grande do Norte. The results allow to end that in the perception of the extension, the level of competitiveness of the productive chain of the coconut in Rio Grande do Norte is still low, presenting as larger fetter the low price of the coconut and the high costs of the productive process, being recommended a larger support to the producing of coconut in relation to technical attendance, incentive actions to the quality, understanding with relationship to the benefits of the creation of partnerships, associations and cooperatives, as well as the promotion of the knowledge of the productive chain of the coconut in Rio Grande do Norte for subsequent ends of all the agents' of that chain training with relationship to the importance of the development of competitive advantages

Avaliação dos processos de seleção utilizados nos programas de fomento a inovação nas micro e pequenas empresas da fundação de amparo à pesquisa do Rio Grande do Norte

Technological innovation promotes the generation of economic value by creating a new product, process or organizational management model, being classified as dynamic and multidimensional. Government intervention has the role of acting through government grant programs to foster the integration of innovative processes in small companies, due to the high costs and risks of development, strengthening the country`s economy in this phase. The distribution of this grant is determined by criteria, based especially in subjective judgments, which are based on the beliefs and perceptions about the technological opportunities and market actors involved in the process, being very difficult to measure the probability of success of the project under evaluation. This study aims to identify the most relevant selection criteria that must be inserted in grants programs at Rio Grande do Norte executed by Fundação de Pesquisa do Rio Grande do Norte (FAPERN). Initially, there was a systematization of 18 countries, covering 41 programs in foreign countries and 29 in Brazil. Based on the data collected, we conducted one survey containing four programs of FAPERN (INOVA I, INOVA II , INOVA III and INOVA IV), covering 44 companies and analyzing their responses according to the Likert scale , obtaining the degree of importance given by the respondent to each of the criteria in the questionnaire . As a result, drew up a proposal for new criteria to be used in the next FAPERN´s grants, containing 13 new criteria. It is expected, therefore, to contribute to a better spending of public funds invested in companies subsidized in Brazil

Controle Adaptativo Robusto para Filtros Ativos de Potência Paralelo

Conventional control strategies used in shunt active power filters (SAPF) employs real-time instantaneous harmonic detection schemes which is usually implements with digital filters. This increase the number of current sensors on the filter structure which results in high costs. Furthermore, these detection schemes introduce time delays which can deteriorate the harmonic compensation performance. Differently from the conventional control schemes, this paper proposes a non-standard control strategy which indirectly regulates the phase currents of the power mains. The reference currents of system are generated by the dc-link voltage controller and is based on the active power balance of SAPF system. The reference currents are aligned to the phase angle of the power mains voltage vector which is obtained by using a dq phase locked loop (PLL) system. The current control strategy is implemented by an adaptive pole placement control strategy integrated to a variable structure control scheme (VS-APPC). In the VS-APPC, the internal model principle (IMP) of reference currents is used for achieving the zero steady state tracking error of the power system currents. This forces the phase current of the system mains to be sinusoidal with low harmonics content. Moreover, the current controllers are implemented on the stationary reference frame to avoid transformations to the mains voltage vector reference coordinates. This proposed current control strategy enhance the performance of SAPF with fast transient response and robustness to parametric uncertainties. Experimental results are showing for determining the effectiveness of SAPF proposed control system

Estratégia de controle robusto para filtro ativo paralelo sem detecção de harmônicos de correntes

Conventional control strategies used in shunt active power filters (SAPF) employs real-time instantaneous harmonic detection schemes which is usually implements with digital filters. This increase the number of current sensors on the filter structure which results in high costs. Furthermore, these detection schemes introduce time delays which can deteriorate the harmonic compensation performance. Differently from the conventional control schemes, this paper proposes a non-standard control strategy which indirectly regulates the phase currents of the power mains. The reference currents of system are generated by the dc-link voltage controller and is based on the active power balance of SAPF system. The reference currents are aligned to the phase angle of the power mains voltage vector which is obtained by using a dq phase locked loop (PLL) system. The current control strategy is implemented by an adaptive pole placement control strategy integrated to a variable structure control scheme (VS¡APPC). In the VS¡APPC, the internal model principle (IMP) of reference currents is used for achieving the zero steady state tracking error of the power system currents. This forces the phase current of the system mains to be sinusoidal with low harmonics content. Moreover, the current controllers are implemented on the stationary reference frame to avoid transformations to the mains voltage vector reference coordinates. This proposed current control strategy enhance the performance of SAPF with fast transient response and robustness to parametric uncertainties. Experimental results are showing for determining the effectiveness of SAPF proposed control system

Remoção mecânica de plantas aquáticas: análise econômica e operacional

A remoção de plantas aquáticas tem sido utilizada como opção ao controle químico e biológico, em razão de restrições ambientais em algumas regiões brasileiras. O objetivo deste trabalho foi desenvolver um modelo para análise econômica e operacional da remoção mecânica de plantas aquáticas, visando realizar estudo econômico comparativo com o controle químico. A operação foi estudada num reservatório de uma usina de bombeamento em Barra do Piraí-RJ. O sistema consiste de retroescavadeiras instaladas em balsas, usadas para cortar as plantas e liberá-las no fluxo de água. Antes da tomada d'água existe uma barreira flutuante que intercepta as plantas, as quais são removidas por um guindaste fixo nas margens. As plantas são armazenadas por algum tempo e depois descartadas. Existe, ainda, um sistema de limpeza das grades da tomada d'água. Dados do volume total de plantas descartadas foram coletados durante 14 meses, assim como foi avaliado o volume de biomassa produzido por área das principais espécies infestantes. A empreiteira que administra o serviço forneceu planilhas de custos e outro parâmetros operacionais. Um modelo foi desenvolvido para calcular custos por hectare de plantas removidas. Os resultados mostraram custo médio mensal de US$ 17.780,28 por hectare. Apesar do alto custo, o sistema de remoção demonstrou capacidade de controlar apenas 4,1% da área infestada no reservatório, na época da coleta dos dados. Simulando dados de uma aplicação de glyphosate, o controle químico custaria apenas 0,23% do custo da remoção. Análises de sensibilidade mostraram que a compactação das plantas para transporte, o volume de plantas produzidas por área e o custo do transporte são os parâmetros principais para a otimização.

Análise da eficiência de aquecedor solar espiral com e sem efeito estufa para piscinas

The technical and economic viability of solar heating for swimming pools is unquestionable, besides there it replaces the high costs and environmental impacts of conventional supply of energy, and it improves an optimization in the pool heating uses. This work applies the principles of the greenhouse effect: advanced thermodynamics, heat retention and equalization of temperature, to optimize the solar heating equipment, reducing the area required by collectors as much as 40% (still estimated value) for commercial collectors, with minor architectural and aesthetic impacts on the environment. It features a solar heating alternative in pools, whose main characteristics: low cost, simplicity in manufacturing and assembly and a faster heating. The system consists of two collectors spiral hoses made of polyethylene with a hundred meters each, and working on a forced flow, with only one pass of the working fluid inside the coils, and is used to pump itself treatment of pool water to obtain the desired flow. One of the collectors will be exposed to direct solar radiation, and the other will be covered by a glass slide and closed laterally, so providing the greenhouse effect. The equipment will be installed in parallel and simultaneously exposed to the sun in order to obtain comparative data on their effectiveness. Will be presented results of thermal tests for this the two cases, with and without transparent cover. Will be demonstrated, by comparison, the thermal, economic and material feasibility of these systems for heating swimming pools.

Avaliação da coluna vertebral: relação entre gibosidade e curvas sagitais por método não-invasivo

Os objetivos do estudo foram avaliar o alinhamento, no plano sagital, da coluna de indivíduos com alterações na medida da gibosidade, comparando com um grupo sem alterações; testar a confiabilidade do instrumento utilizado e verificar se existem correlações entre as medidas da gibosidade e os valores das curvaturas vertebrais. Foram avaliados 40 jovens, divididos em grupo controle - ausência ou presença de gibosidades inferiores a 0,5 cm na curvatura torácica e 0,7 cm na lombar (n=20) e, grupo experimental - gibosidades superiores às descritas (n=20). A gibosidade e as curvaturas no plano sagital foram mensuradas com um instrumento adaptado a um nível d'água e o teste de Adams. As coletas foram realizadas em duas datas distintas, nos dois grupos. Após aplicação do teste Mann-Whitney não foi encontrada diferença entre as ocasiões de coletas e, emparelhando-se os grupos, foi encontrada diferença apenas na medida cervical. Na verificação de existência de relação entre as medidas coletadas, foi encontrada correlação linear (Spearmann) no grupo controle - curvatura torácica e gibosidade torácica; em ambos os grupos - curvaturas torácica e lombar; e no grupo experimental - gibosidade torácica e as curvaturas lombar e sacral e, curvatura sacral e curvaturas torácica e lombar. Pôde-se concluir que a medida da gibosidade tem relações com as curvaturas no plano sagital. Por ser um método confiável, simples e acessível, pode ser reproduzido sem altos custos financeiros e sem causar prejuízo à saúde do paciente.

Physical-chemical and thermodynamic analyses of ethanol steam reforming for hydrogen production

Steam reforming is the most usual method of hydrogen production due to its high production efficiency and technological maturity the use of ethanol for this purpose is an interesting option because it is a renewable and environmentally friendly fuel. The objective of this article is to present the physical-chemical, thermodynamic, and exergetic analysis of a steam reformer of ethanol, in order to produce 0.7 Nm(3)/h of hydrogen as feedstock of a 1 kW PEMFC the global reaction of ethanol is considered. Superheated ethanol reacts with steam at high temperatures producing hydrogen and carbon dioxide, depending strongly on the thermodynamic conditions of reforming, as well as on the technical features of the reformer system and catalysts. The thermodynamic analysis shows the feasibility of this reaction in temperatures about 206 degrees C. Below this temperature, the reaction trends to the reactants. The advance degree increases with temperature and decreases with pressure. Optimal temperatures range between 600 and 700 degrees C. However, when the temperature attains 700 degrees C, the reaction stability occurs, that is, the hydrogen production attains the limit. For temperatures above 700 degrees C, the heat use is very high, involving high costs of production due to the higher volume of fuel or electricity used. The optimal pressure is 1 atm., e.g., at atmospheric pressure. The exergetic analysis shows that the lower irreversibility is attained for lower pressures. However the temperature changes do not affect significantly the irreversibilities. This analysis shows that the best thermodynamic conditions for steam reforming of ethanol are the same conditions suggested in the physical-chemical analysis.

A experiência de adolescentes portadores de diabetes Mellitus Tipo 1: seus significados e sentido

Worldwide, the diabetes mellitus is considered a serious problem of public health; it also involves high costs for its treatment and its complications. Even though the onset of diabetes mellitus type 1 is on 5% to 10% of the diabetic population, it is the most aggressive type of anifestation; furthermore, it is the commonest chronic disease in childhood and adolescence. Such data show the importance of understanding the development of this disease from the moment the individual perceives it, according to their experience, observing the complexity of the phenomenon thoroughly. This study aimed to comprehend the experience of the adolescent with onset of diabetes mellitus type 1 in order to learn how these young individuals perceive and reason their place in the world when they experience this illness. The methodological strategy was based on qualitative research of phenomenological inspiration. We applied the main ideas of heideggerian ontology and some concepts of existential phenomenological psychology to guide our reflexive path. The participants were 10 young individuals (06 female and 04 male), ages between 15 and 18, under treatment in the city of Recife, Pernambuco. The methodological resource was the narrative, which allowed us access to the adolescents experience. The comprehension of the reports was based on the heideggerian hermeneutics, whose priority is the interpretation of the meaning expressed by the participants speech. The results showed that factors such as social, family, economic and cultural context greatly influence the perception and the way the individuals deal with, perceive and reason their experience. We noticed that the diabetes type 1 may often represent a limitation, but it does not make it impossible to be part of the world with others. The data show a significant affective ambivalence regarding the content more directly related to the disease. This demonstrates the unique way which each one gives meaning and reasons their condition of existence. This research points out the need to understand the complexity of this phenomenon in a more complete manner, considering the adolescent in their timely and historical context. We believe we can encourage thinking that may become actions which are more fit to the reality researched regarding all the parties involved with the subject, such as health professionals, adolescents, family, support programs and public health policies

Reactive Control for Transmission Overload Relief Based on Sensitivity Analysis and Cooperative Game Theory

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Comparação de custos de implantação de eucalipto com resíduo celulósico em substituição ao fertilizante mineral

A grande expansão das indústrias e do mercado consumidor tem provocado, nas últimas décadas, a geração de elevadas quantidades de resíduos, os quais têm constituído constante preocupação econômica e ambiental. Objetivou-se, neste trabalho, analisar a viabilidade econômica do uso de três doses de composto orgânico, oriundo da compostagem de resíduos da extração da celulose, em substituição à adubação mineral, na cultura do eucalipto, no município de Selvíria, MS. A metodologia de custos adotada foi a do custo operacional total e do custo total. Concluiu-se que, por causa do elevado custo de transporte e aplicação, a adubação orgânica mostrou-se mais onerosa em relação à mineral, sendo sua utilização viável, economicamente, apenas nas proximidades da indústria produtora.

Sistema TS-FF-AAS com chama acetileno-ar como alternativa em relação à chama acetileno-óxido nitroso em FAAS na determinação de estanho

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Metodologia e aplicação da citometria de fluxo na hematologia veterinária

A citometria de fluxo é um método emergente na medicina veterinária que permite a identificação e quantificação de células em suspensão. Apesar do custo elevado e da necessidade de técnicos especializados para realização da avaliação citofluorométrica, esta técnica tem uma ampla aplicação na hematologia veterinária, incluindo a avaliação de células-tronco hematopoiéticas, eritrócitos, leucócitos e plaquetas. O grande potencial de aplicação clínica da citometria de fluxo inclui a quantificação das células CD34+ como indicação da capacidade de reconstituição hematopoiética após o transplante de células-tronco e das subpopulações linfocitárias para avaliação da resposta imune frente aos transplantes e às doenças que acometem os animais. Projetos científicos sobre a avaliação citofluorométrica das células-tronco e subpopulações linfocitárias de cães têm sido desenvolvidos com sucesso por pesquisadores da área de hematologia veterinária na Universidade Estadual Paulista (UNESP), Campus de Jaboticabal. Portanto, no futuro, a citometria de fluxo deve se tornar uma técnica de rotina em laboratórios veterinários no Brasil.