Development and validation of an environmentally friendly attenuated total reflectance in the mid-infrared region method for the determination of ethanol content in used engine lubrication oil

Lubricating oils are crucial in the operation of automotive engines because they both reduce friction between moving parts and protect against corrosion. However, the performance of lubricant oil may be affected by contaminants, such as gasoline, diesel, ethanol, water and ethylene glycol. Although there are many standard methods and studies related to the quantification of contaminants in lubricant oil, such as gasoline and diesel oil, to the best of our knowledge, no methods have been reported for the quantification of ethanol in used Otto cycle engine lubrication oils. Therefore, this work aimed at the development and validation of a routine method based on partial least-squares multivariate analysis combined with attenuated total reflectance in the mid-infrared region to quantify ethanol content in used lubrication oil. The method was validated based on its figures of merit (using the net analyte signal) as follows: limit of detection (0.049%), limit of quantification (0.16%), accuracy (root mean square error of prediction=0.089% w/w), repeatability (0.05% w/w), fit (R 2 =0.9997), mean selectivity (0.047), sensitivity (0.011), inverse analytical sensitivity (0.016% w/w-1) and signal-to-noise ratio (max: 812.4 and min: 200.9). The results show that the proposed method can be routinely implemented for the quality control of lubricant oils. © 2013 Elsevier B.V. All rights reserved.

Mapeamento de tecnologias informacionais sobre dados abertos em saúde pública: destino de repasses financeiros federais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Case study on the complementary manufacture of engine components in Argentina and Brazil

Information Paper, No 26

Trade Facilitation: Promoting Trade as an Engine of Growth Using Information and Communication Technologies (ICTS)

Three factors define the main difficulties faced by developing countries in the area of trade facilitation: (i) limited understanding and use by governments and business (especially SMEs) of trade facilitation and of ICT tools and techniques; (ii) developing countries' limited capacity for policy analysis and inadequate policy instruments for the implementation of trade facilitation, and (iii) inadequate policy coordination for negotiation on trade facilitation. These obstacles tend to reduce countries' development opportunities and to increase the costs of general economic development and social welfare.The United Nations, through its five regional commissions, is launching a project that seeks to disseminate the benefits of trade facilitation and the standards, tools and requirements for its successful implementation. The project will focus on trade facilitation promoted by: (a) enhanced knowledge and understanding of governments and business regarding trade facilitation and the role of ICT; (b) enhanced use of ICT by SMEs in trade facilitation, and (c) national capacity-building for trade facilitation negotiations.

Internal Combustion Engine's Throttle Control as a Motivational Theme for Teaching Microprocessors Systems Lab Classes

The increased fuel economy and driveability of modern internal combustion engine vehicles (ICEVs) are the result of the application of advanced digital electronics to control the operation of the internal combustion engine (ICE). Microprocessors (and micro controllers) play a key role in the engine control, by precisely controlling the amount of both air and fuel admitted into the cylinders. Air intake is controlled by utilizing a throttle valve equipped with a motor and gear mechanism as actuator, and a sensor enabling the measurement of the angular position of the blades. This paperwork presents a lab setup that allows students to control the throttle position using a microcontroller that runs a program developed by them. A commercial throttle body has been employed, whereas a power amplifier and a microcontroller board have been hand assembled to complete the experimental setup. This setup, while based in a high-tech, microprocessor-based solution for a real-world, engine operation optimization problem, has the potential to engage students around a hands-on multidisciplinary lab activity and ignite their interest in learning fundamental and advanced topics of microprocessors systems.

Comparative analysis between a PEM fuel cell and an internal combustion engine driving an electricity generator: Technical, economical and ecological aspects

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Performance and emissions of a gas turbine engine using ox tallow ethyl-ester blended with kerosene

The performance and emissions behavior of a Rover 1S/60 turboshaft engine when operated with several blends of aviation kerosene and ox tallow ethyl-ester are shown in this article. The tests were performed with a compressor shaft coupled to an hydraulic dynamometer where data of power and mass fuel flow were collected to determine the brake specific fuel consumption. A flue gas analyzer was positioned at the exhaust duct to collect oxygen, carbon dioxide, carbon monoxide and nitrous oxides. An increase in the specific fuel consumption was observed due to the lesser lower heating value of the most oxygenated blends. However, reductions of CO, CO2 and NO (x) have been observed and no-significant ill effects have occurred in the turbine operation.

Engine LES with fuel-spray modeling

Pós-graduação em Engenharia Mecânica - FEG

Computer graphics applied to anatomy: a study of two bio-cad modeling methods on finite element analysis of human edentulous hemi-mandible

Modeling is a step to perform a finite element analysis. Different methods of model construction are reported in literature, as the Bio-CAD modeling. The purpose of this study was to perform a model evaluation and application using two methods of Bio-CAD modeling from human edentulous hemi-mandible on the finite element analysis. From CT scans of dried human skull was reconstructed a stereolithographic model. Two methods of modeling were performed: STL conversion approach (Model 1) associated to STL simplification and reverse engineering approach (Model 2). For finite element analysis was used the action of lateral pterygoid muscle as loading condition to assess total displacement (D), equivalent von-Mises stress (VM) and maximum principal stress (MP). Two models presented differences on the geometry regarding surface number (1834 (model 1); 282 (model 2)). Were observed differences in finite element mesh regarding element number (30428 nodes/16683 elements (model 1); 15801 nodes/8410 elements (model 2). D, VM and MP stress areas presented similar distribution in two models. The values were different regarding maximum and minimum values of D (ranging 0-0.511 mm (model 1) and 0-0.544 mm (model 2), VM stress (6.36E-04-11.4 MPa (model 1) and 2.15E-04-14.7 MPa (model 2) and MP stress (-1.43-9.14 MPa (model 1) and -1.2-11.6 MPa (model 2). From two methods of Bio-CAD modeling, the reverse engineering presented better anatomical representation compared to the STL conversion approach. The models presented differences in the finite element mesh, total displacement and stress distribution.

Airport Bird Threat in North America from Large Flocking Birds (geese) (as Viewed by an Engine Manufacturer)--Part 1

In worldwide aviation operations, bird collisions with aircraft and ingestions into engine inlets present safety hazards and financial loss through equipment damage, loss of service and disruption to operations. The problem is encountered by all types of aircraft, both military and commercial. Modern aircraft engines have achieved a high level of reliability while manufacturers and users continually strive to further improve the safety record. A major safety concern today includes common-cause events which involve significant power loss on more than one engine. These are externally-inflicted occurrences, with the most frequent being encounters with flocks of birds. Most frequently these encounters occur during flight operations in the area on or near airports, near the ground instead of at cruise altitude conditions. This paper focuses on the increasing threat to aircraft and engines posed by the recorded growth in geese populations in North America. Service data show that goose strikes are increasing, especially in North America, consistent with the growing resident geese populations estimated by the United States Department of Agriculture (USDA). Airport managers, along with the governmental authorities, need to develop a strategy to address this large flocking bird issue. This paper also presents statistics on the overall status of the bird threat for birds of all sizes in North America relative to other geographic regions. Overall, the data shows that Canada and the USA have had marked improvements in controlling the threat from damaging birds - except for the increase in geese strikes. To reduce bird ingestion hazards, more aggressive corrective measures are needed in international air transport to reduce the chances of serious incidents or accidents from bird ingestion encounters. Air transport authorities must continue to take preventative and avoidance actions to counter the threat of birdstrikes to aircraft. The primary objective of this paper is to increase awareness of, and focus attention on, the safety hazards presented by large flocking birds such as geese. In the worst case, multiple engine power loss due to large bird ingestion could result in an off-airport forced landing accident. Hopefully, such awareness will prompt governmental regulatory agencies to address the hazards associated with growing populations of geese in North America.

ENHANCEMENT OF THE FAA’s ON-LINE WILDLIFE AIRCRAFT STRIKE DATABASE WITH AN INTERACTIVE GRAPHICS CAPABILITY

Embry-Riddle Aeronautical University (Prescott, AZ, USA) was awarded a grant from the William J. Hughes FAA Technical Center in October 1999 to develop and maintain a web site dealing with a wide variety of airport safety wildlife concerns. Initially, the web site enabled users to access related topics such as wildlife management (at/near airports), bird identification information, FAA wildlife management guidelines, education, pictures, current news, upcoming meetings and training, available jobs and discussion/forum sections. In April 2001, the web site was augmented with an on-line wildlife strike report (FAA Form 5200-7). Upon submittal on-line, “quick look” email notifications are sent to concerned government personnel. The distribution of these emails varies as to whether there was damage, human injuries/fatalities, and whether feather remains were collected and will be sent to the Smithsonian Institution for identification. In July 2002, a real-time on-line query system was incorporated to allow federal and local government agencies, airport and operator personnel, and USDA and airport wildlife biologists to access this database (which as of June 2005 contains 68,288 researched strike reports added to at a rate of approximately 500 strike reports/month) to formulate strategies to reduce the hazards wildlife present to aviation. To date (June 2005), over 15,000 on-line real-time queries were processed. In June 2004, ERAU was authorized to develop a graphical interface to this on-line query system. Current capabilities include mapping strikes (by species) on the US map, each of the contiguous 48 state maps (with AK and HI being added), and airport diagrams of the major metropolitan airports as well as the next 46 airports with the most reported strikes The latter capability depicts strikes by runway in plan as well as in elevation view. Currently under development is the ability to view time-sequenced strikes on the US map. This extensive graphical interface will give analysts the ability to view strike patterns with a wide variety of variables including species, seasons, migration patterns, etc. on US and state maps and airport diagrams.

Particle emission from heavy-duty engine fuelled with blended diesel and biodiesel

In this study, particulate matter (PM) were characterized from a place impacted by heavy-duty vehicles (Bus Station) fuelled with diesel/biodiesel fuel blend (B3) in the city of Londrina, Brazil. Sixteen priority polycyclic aromatic hydrocarbons (PAH) concentrations were analyzed in the samples by their association with atmospheric PM, mass size distributions and major ions (fluorite, chloride, bromide, nitrate, phosphate, sulfate, nitrite, oxalate; fumarate, formate, succinate and acetate; lithium, sodium, potassium, magnesium, calcium and ammonium). Results indicate that major ions represented 21.2% particulate matter mass. Nitrate, sulfate, and ammonium, respectively, presented the highest concentration levels, indicating that biodiesel may also be a significant source for these ions, especially nitrate. Dibenzo[a,h]anthracene and indeno[1,2,3,-cd]pyrene were the main PAH found, and a higher fraction of PAH particles was found in diameters lower than 0.25 mu m in Londrina bus station. The fine and ultrafine particles were dominant among the PM evaluated, suggesting that biodiesel decreases the total PAH emission. However, it does also increase the fraction of fine and ultrafine particles when compared to diesel.

MOOGLE: a metamodel-based model search engine

Models are becoming increasingly important in the software development process. As a consequence, the number of models being used is increasing, and so is the need for efficient mechanisms to search them. Various existing search engines could be used for this purpose, but they lack features to properly search models, mainly because they are strongly focused on text-based search. This paper presents Moogle, a model search engine that uses metamodeling information to create richer search indexes and to allow more complex queries to be performed. The paper also presents the results of an evaluation of Moogle, which showed that the metamodel information improves the accuracy of the search.

Wildfire prevention and management in a 3D virtual environment

[EN] This paper describes a wildfire forecasting application based on a 3D virtual environment and a fire simulation engine. A new open source framework is presented for the development of 3D graphics applications over large geographic areas offering high performance 3D visualization and powerful interaction tools for the Geographic Information Systems community. The application includes a remote module that allows simultaneous connection of several users for monitoring a real wildfire event. The user is enabled to simulate and visualize a wildfire spreading on the terrain under conditions of spatial information on topography and fuels along with weather and wind files.

Forecasting and visualization of wildfires in a 3D geographical information system

[EN]This paper describes a wildfi re forecasting application based on a 3D virtual environment and a fi re simulation engine. A novel open source framework is presented for the development of 3D graphics applications over large geographic areas, off ering high performance 3D visualization and powerful interaction tools for the Geographic Information Systems (GIS) community. The application includes a remote module that allows simultaneous connection of several users for monitoring a real wildfi re event.