Is bus overrepresented in Bluetooth MAC Scanner data? Is MAC-ID really unique?

One of the concerns about the use of Bluetooth MAC Scanner (BMS) data, especially from urban arterial, is the bias in the travel time estimates from multiple Bluetooth devices being transported by a vehicle. For instance, if a bus is transporting 20 passengers with Bluetooth equipped mobile phones, then the discovery of these mobile phones by BMS will be considered as 20 different vehicles, and the average travel time along the corridor estimated from the BMS data will be biased with the travel time from the bus. This paper integrates Bus Vehicle Identification system with BMS network to empirically evaluate such bias, if any. The paper also reports an interesting finding on the uniqueness of MAC IDs.

Urban traffic state estimation: Fusing point and zone based data

Loop detectors are the oldest and widely used traffic data source. On urban arterials, they are mainly installed for signal control. Recently state of the art Bluetooth MAC Scanners (BMS) has significantly captured the interest of stakeholders for exploiting it for area wide traffic monitoring. Loop detectors provide flow- a fundamental traffic parameter; whereas BMS provides individual vehicle travel time between BMS stations. Hence, these two data sources complement each other, and if integrated should increase the accuracy and reliability of the traffic state estimation. This paper proposed a model that integrates loops and BMS data for seamless travel time and density estimation for urban signalised network. The proposed model is validated using both real and simulated data and the results indicate that the accuracy of the proposed model is over 90%.

Noisy Bluetooth traffic data?

Traffic state estimation in an urban road network remains a challenge for traffic models and the question of how such a network performs remains a difficult one to answer for traffic operators. Lack of detailed traffic information has long restricted research in this area. The introduction of Bluetooth into the automotive world presented an alternative that has now developed to a stage where large-scale test-beds are becoming available, for traffic monitoring and model validation purposes. But how much confidence should we have in such data? This paper aims to give an overview of the usage of Bluetooth, primarily for the city-scale management of urban transport networks, and to encourage researchers and practitioners to take a more cautious look at what is currently understood as a mature technology for monitoring travellers in urban environments. We argue that the full value of this technology is yet to be realised, for the analytical accuracies peculiar to the data have still to be adequately resolved.

Data collection techniques

The objective of this chapter is to provide an overview of traffic data collection that can and should be used for the calibration and validation of traffic simulation models. There are big differences in availability of data from different sources. Some types of data such as loop detector data are widely available and used. Some can be measured with additional effort, for example, travel time data from GPS probe vehicles. Some types such as trajectory data are available only in rare situations such as research projects.

4D GPR tracking of water infiltration in fractured high-porosity limestone

Three thousand liters of water were infiltrated from a 4 m diameter pond to track flow and transport inside fractured carbonates with 20-40 % porosity. Sixteen time-lapse 3D Ground Penetrating Radar (GPR) surveys with repetition intervals between 2 hrs and 5 days monitored the spreading of the water bulb in the subsurface. Based on local travel time shifts between repeated GPR survey pairs, localized changes of volumetric water content can be related to the processes of wetting, saturation and drainage. Deformation bands consisting of thin sub vertical sheets of crushed grains reduce the magnitude of water content changes but enhance flow in sheet parallel direction. This causes an earlier break through across a stratigraphic boundary compared to porous limestone without deformation bands. This experiment shows how time-lapse 3D GPR or 4D GPR can non-invasively track ongoing flow processes in rock-volumes of over 100 m3.

Effects of transit quality of service characteristics on daily bus ridership

This study explores how explicit transit quality of services (TQoS) measures including service frequency, service span, and travel time ratio, along with implicit environmental predictors such as topographic grade factor influence bus ridership using a case study city of Brisbane, Australia. The primary hypothesis tested was that bus ridership is higher within suburbs with high transit quality of service than suburbs that have limited service quality. Using Multiple Linear Regression (MLR) this study identifies a strong positive relationship between route intensity (bus-km/h-km2) and bus ridership, indicating that increasing both service frequency and spatial route density correspond to higher bus ridership. Additionally, travel time ratio (in-vehicle transit travel time to in-vehicle auto travel time) is also found to have significant negative association with ridership within a suburb, reflecting a decline in transit use with increased travel time ratio. Conversely, topographic grade and service span are not found to exert any significant impact on bus ridership in a suburb. Our study findings enhance the fundamental understanding of traveller behaviour which is informative to urban transportation policy, planning and provision.

Effects of transit quality of service characteristics on daily bus ridership

This study investigates whether an Australian city’s suburbs having high transit Quality of Service (QoS) are associated with higher transit ridership than those having low transit QoS •We explore how QoS measures including service frequency, service span, service coverage, and travel time ratio, along with implicit environmental predictors such as topographic grade factor influence bus ridership •We applied Multiple Linear Regression (MLR) to examine the relationship between QoS and ridership •Its outcomes enhance our understanding of transit user behavior, which is informative to urban transportation policy, planning, and provision

Retrieving trip information from a discrete detectors network : The case of Brisbane Bluetooth detectors

Automatic Vehicle Identification Systems are being increasingly used as a new source of travel information. As in the last decades these systems relied on expensive new technologies, few of them were scattered along a networks making thus Travel-Time and Average Speed estimation their main objectives. However, as their price dropped, the opportunity of building dense AVI networks arose, as in Brisbane where more than 250 Bluetooth detectors are now installed. As a consequence this technology represents an effective means to acquire accurate time dependant Origin Destination information. In order to obtain reliable estimations, however, a number of issues need to be addressed. Some of these problems stem from the structure of a network made out of isolated detectors itself while others are inherent of Bluetooth technology (overlapping detection area, missing detections,\...). The aim of this paper is threefold: First, after having presented the level of details that can be reached with a network of isolated detectors we present how we modelled Brisbane's network, keeping only the information valuable for the retrieval of trip information. Second, we give an overview of the issues inherent to the Bluetooth technology and we propose a method for retrieving the itineraries of the individual Bluetooth vehicles. Last, through a comparison with Brisbane Transport Strategic Model results, we highlight the opportunities and the limits of Bluetooth detectors networks. The aim of this paper is twofold. We first give a comprehensive overview of the aforementioned issues. Further, we propose a methodology that can be followed, in order to cleanse, correct and aggregate Bluetooth data. We postulate that the methods introduced by this paper are the first crucial steps that need to be followed in order to compute accurate Origin-Destination matrices in urban road networks.

Shortest path and vehicle trajectory aided map-matching for low frequency GPS data

Map-matching algorithms that utilise road segment connectivity along with other data (i.e.position, speed and heading) in the process of map-matching are normally suitable for high frequency (1 Hz or higher) positioning data from GPS. While applying such map-matching algorithms to low frequency data (such as data from a fleet of private cars, buses or light duty vehicles or smartphones), the performance of these algorithms reduces to in the region of 70% in terms of correct link identification, especially in urban and sub-urban road networks. This level of performance may be insufficient for some real-time Intelligent Transport System (ITS) applications and services such as estimating link travel time and speed from low frequency GPS data. Therefore, this paper develops a new weight-based shortest path and vehicle trajectory aided map-matching (stMM) algorithm that enhances the map-matching of low frequency positioning data on a road map. The well-known A* search algorithm is employed to derive the shortest path between two points while taking into account both link connectivity and turn restrictions at junctions. In the developed stMM algorithm, two additional weights related to the shortest path and vehicle trajectory are considered: one shortest path-based weight is related to the distance along the shortest path and the distance along the vehicle trajectory, while the other is associated with the heading difference of the vehicle trajectory. The developed stMM algorithm is tested using a series of real-world datasets of varying frequencies (i.e. 1 s, 5 s, 30 s, 60 s sampling intervals). A high-accuracy integrated navigation system (a high-grade inertial navigation system and a carrier-phase GPS receiver) is used to measure the accuracy of the developed algorithm. The results suggest that the algorithm identifies 98.9% of the links correctly for every 30 s GPS data. Omitting the information from the shortest path and vehicle trajectory, the accuracy of the algorithm reduces to about 73% in terms of correct link identification. The algorithm can process on average 50 positioning fixes per second making it suitable for real-time ITS applications and services.

Utilising big transit data for transfer coordination

In public transport, seamless coordinated transfer strengthens the quality of service and attracts ridership. The problem of transfer coordination is sophisticated due to (1) the stochasticity of travel time variability, (2) unavailability of passenger transfer plan. However, the proliferation of Big Data technologies provides a tremendous opportunity to solve these problems. This dissertation enhances passenger transfer quality by offline and online transfer coordination. While offline transfer coordination exploits the knowledge of travel time variability to coordinate transfers, online transfer coordination provides simultaneous vehicle arrivals at stops to facilitate transfers by employing the knowledge of passenger behaviours.

Measuring route passenger load diversity for capacity and quality of service assessment

This paper develops theory that quantifies transit route passenger-relative load factor and distinguishes it from occupancy load factor. The ratio between these measures is defined as the load diversity coefficient, which as a single measure characterizes the diversity of passenger load factor between route segments according to the origin-destination profile. The relationship between load diversity coefficient and route coefficient of variation in occupancy load factor is quantified. Two tables are provided that enhance passenger capacity and quality of service (QoS) assessment regarding onboard passenger load. The first expresses the transit operator’s perspective of load diversity and the passengers’ perspective of load factor relative to the operator’s, across six service levels corresponding to ranges of coefficient of variation in occupancy load factor. The second interprets the relationships between passenger average travel time and each of passenger-relative load factor and occupancy load factor. The application of this methodology is illustrated using a case study of a premium radial bus route in Brisbane, Australia. The methodology can assist in benchmarking and decision making regarding route and schedule design. Future research will apply value of time to QoS measurement, reflecting perceived passenger comfort through crowding and average time spent aboard. This would also assist in transit service quality econometric modeling.

Measuring route passenger load diversity for capacity and quality of service assessment

This poster introduces Passenger Relative Load Factor for a route or individual bus service as a capacity and quality of service measure, distinguishing it from Occupancy Load Factor. It introduces Load Diversity Coefficient as the ratio of Passenger Relative Load Factor to Occupancy Load Factor, and relates Load Diversity Coefficient to Coefficient of Variation in Occupancy Load Factor. It qualifies the operator’s and passengers’ perspectives of load factor based on Coefficient of Variation in Occupancy Load Factor along a route. A case study using weekday Automatic Fare Collection (AFC) data on a premium bus line in Brisbane, Australia illustrates the methodology. The compendium paper also qualifies the operator’s and passengers’ perspectives of these load factors along with Passengers’ Average Travel Time for capacity and quality of service assessment.

Enhancing professional learning for rural educators by rethinking connectedness

Impending changes in Australian education brings forth the expected transformation of teachers working in schools. Three key points for transforming Australian schools has been identified by Gillard (2008a) including the improvement of quality teaching, ensuring every child benefits and mandating transparency and accountability. A number of initiatives were considered to assist with such reform including the implementation of a Digital Education Revolution, the move to the Australian Curriculum and the implementation of a National Framework for Professional Standards for Teaching. As these transformative initiatives are rolled out to teachers across Australia, the equitable access to PD to support all teachers, regardless of their geographical location, is in question. In line with the literature, the author proposes the concept of delivering PD and accessing PD from regional and remote areas be reconsidered. This research paper will outline the findings from the study including travel time being significant and impacting on teachers personal time; limited relief teachers impacting on access to PD; promotion and teacher registration being explicitly linked to PD; professional learning communities being valued but often limited by small staff numbers; professional learning conducted in the local context being preferred; professional learning established at the teacher and school level being desirable; teachers being confident in using technology and accessing PD online if required; and social cohesiveness being valued and often limited by isolation. Further this research has culminated in the development of a conceptual framework that would facilitate improving the amount and variety of professional learning available to regional and remote teachers.

Rethinking connectedness : an investigation into the access of teacher professional learning in regional and remote Western Australia

Many teachers working in remote and regional areas have limited access to collegial support networks. This research aimed to examine the existing strategies that were being undertaken by the Department of Education in Western Australia, to provide professional learning to teachers in regional and remote areas. It was important to establish the perceptions of teachers’ access to professional learning from those working at the coalface in geographically dispersed areas. Consequently, the possible opportunity for improving the amount and variety of professional learning, through the application of both synchronous and asynchronous technologies was proposed. The study was guided by the primary research question: “In what ways might technology be used to support professional development of regional and remote teachers in Western Australia?” Generating descriptions of current practice of professional learning along with the teacher perceptions were central to this research endeavour. The study relied on a mixed method research approach in order to attend to the research question. The data were collected in phases, referred to as an explanatory mixed methods design. Quantitative data were collected from 104 participants to provide a general picture of the research problem. To further refine this general picture, qualitative data were collected through interviews and e-interviews of 10 teachers. Participants in the study included graduate teachers, teachers who had taught more than two years, senior teachers and Level Three teachers from seven teaching districts within Western Australia. An investigation into current practice was included in this phase and technologies available to support a professional learning community over distance were documented. The final phase incorporated the formulation of a conceptual framework where a model was developed to facilitate the successful implementation of a professional learning community through the application of synchronous and asynchronous technologies. The study has identified that travel time in order to access professional development is significant and impacts on teachers’ personal time. There are limited relief teachers available in these isolated areas which impacts on the opportunities to access professional development. Teachers face inequities, in terms of promotion, because professional development is explicitly linked to promotional opportunities. Importantly, it was found that professional learning communities are valued, but are often limited by small staff numbers at the geographic locality of the school. Teachers preferred to undertake professional learning in the local context of their district, school or classroom and this professional learning must be established at the need of the individual teacher in line with the school priorities. Teachers reported they were confident in using technology and accessing professional development online if required, however, much uncertainty surrounded the use of web 2.0 technologies for this purpose. The recommendations made from the study are intended to identify how a professional learning community might be enhanced through synchronous and asynchronous technologies.

Rethinking connectedness: improving access to professional learning for regional and remote teachers

Transformation of Australian education is occurring at a rapid rate through the implementation of a number of initiatives. These initiatives include the Digital Education Revolution, the move to a National Curriculum and the implementation of a National Framework for Professional Standards for Teachers and Principals. As these initiatives are rolled out to schools across Australia, the equitable access to professional learning to support all teachers, regardless of their geographical location, is in question. A number of studies have been conducted in Australia that highlight the importance of professional learning and the difficulty faced by regional and remote teachers with regard to access (Gerard Daniels, 2007; Lysons, Cooksey, Panizzon, Parnell & Pegg 2006; Ministerial Review of Schooling, 1994, Rural and Remote Education Advisory Council, 2000; Vinson, 2002). Along with access to professional learning, has been the discussion of effective modes of delivery. Face to face professional learning, in regional and metropolitan areas, is offered in isolation, or in some cases, is complimented with virtual learning environments. The need for a more sustainable approach to professional learning is highly necessary. A mixed method research approach was utilised in order to answer the primary research question "In what ways might technology be used to support professional learning of regional and remote teachers in Western Australia?" This research paper outlines the findings from the study including the significance of travel time; impact of limited relief teachers; implications for promotion and teacher registration; professional learning communities being valued but often limited by small staff numbers; professional learning conducted in the local context being preferred; professional learning established at the teacher and school level being desirable; teachers being confident in using technology and accessing PD online if required; and social cohesiveness being valued and often limited by isolation. Further, this research has culminated in the development of a "model of rethinking connectedness" that would facilitate improving the amount and variety of professional learning available to regional and remote teachers.