962 resultados para Fonvizin, D. I. (Denis Ivanovich), 1745-1792
Resumo:
In this paper we report on a search for short-duration gravitational wave bursts in the frequency range 64 Hz-1792 Hz associated with gamma-ray bursts (GRBs), using data from GEO 600 and one of the LIGO or Virgo detectors. We introduce the method of a linear search grid to analyze GRB events with large sky localization uncertainties, for example the localizations provided by the Fermi Gamma-ray Burst Monitor (GBM). Coherent searches for gravitational waves (GWs) can be computationally intensive when the GRB sky position is not well localized, due to the corrections required for the difference in arrival time between detectors. Using a linear search grid we are able to reduce the computational cost of the analysis by a factor of O(10) for GBM events. Furthermore, we demonstrate that our analysis pipeline can improve upon the sky localization of GRBs detected by the GBM, if a high-frequency GW signal is observed in coincidence. We use the method of the linear grid in a search for GWs associated with 129 GRBs observed satellite-based gamma-ray experiments between 2006 and 2011. The GRBs in our sample had not been previously analyzed for GW counterparts. A fraction of our GRB events are analyzed using data from GEO 600 while the detector was using squeezed-light states to improve its sensitivity; this is the first search for GWs using data from a squeezed-light interferometric observatory. We find no evidence for GW signals, either with any individual GRB in this sample or with the population as a whole. For each GRB we place lower bounds on the distance to the progenitor, under an assumption of a fixed GW emission energy of 10(-2)M circle dot c(2), with a median exclusion distance of 0.8 Mpc for emission at 500 Hz and 0.3 Mpc at 1 kHz. The reduced computational cost associated with a linear search grid will enable rapid searches for GWs associated with Fermi GBM events once the advanced LIGO and Virgo detectors begin operation.
Resumo:
The P-T-differential inclusive production cross section of the prompt charm-strange meson D-s(+) in the rapidity range vertical bar y vertical bar < 0.5 was measured in proton-proton collisions at root s = 7 TeV at the LHC using the ALICE detector. The analysis was performed on a data sample of 2.98 x 10(8) events collected with a minimum-bias trigger. The corresponding integrated luminosity is L-int = 4.8 nb(-1). Reconstructing the decay D-s(+) -> phi pi(+) with phi -> K-K+, and its charge conjugate, about 480 D-s(+/-) mesons were counted, after selection cuts, in the transverse momentum range 2 < P-T < 12 GeV/c. The results are compared with predictions from models based on perturbative QCD. The ratios of the cross sections of four D meson species (namely D-0, D+, D*+ and D-s(+)) were determined both as a function of p(T) and integrated over p(T)after extrapolating to full p(T) range, together with the strangeness suppression factor in charm fragmentation. The obtained values are found to be compatible within uncertainties with those measured by other experiments in e(+)e(-), ep and pp interactions at various centre-of-mass energies. (C) 2012 CERN. Published by Elsevier By. All rights reserved.
Resumo:
Numerose evidenze dimostrano che le proprietà dei materiali compositi sono strettamente legate ai processi produttivi, alle tipologie di fibra e resina impiegate nel materiale stesso. Proprietà caratterizzate anche dai difetti contenuti nel materiale stesso. Nella tesi si presta particolare attenzione al processo produttivo con prepreg e autoclave trattando anche il tema della stesura di un ply-book. Si valutano in modo teorico e critico alcuni tra i metodi N.D.T. più avanzati tra cui: P.T.(Penetrant Test), Rx(Radiography Test), UT (Ultrasound Test in Phased Array) e IRT (InfraRed Termography - Pulsata). Molteplici sono i componenti testati che variano tra loro per: tipologia di resina e fibra impiegata, processo produttivo e geometria. Tutti questi componenti permettono di capire come i singoli parametri influenzino la visualizzazione e l'applicabilità delle tecniche N.D.T. sopra citate. Su alcuni provini è stata eseguita la prova meccanica Drop Weight Test secondo ASTM D7136 per correlare le aree di delaminazione indotte e la sensibilità di ogni singolo metodo, visualizzando così la criticità indotta dagli urti con bassa energia di impatto (BVID Barely Invisible Impact)di cui i materiali compositi soffrono durante la "service life". A conclusione del lavoro si potrà comprendere come solo l'analisi con più metodi in parallelo permetta di ottenere una adeguata Probability Of Detection.
Resumo:
von einem Proletarier [d.i. Fritz Kemper]
Resumo:
geh. von Horatius Cocles [d.i. Karl Christian Ernst Graf von Benzel-Sternau]
Resumo:
[Tsarphati, d.i. Olry Terquem]
Resumo:
von Maximilian Parmod [d.i. Max Apt]
Resumo:
von Leo Rauchmann [d.i. Jakob Stern]
Resumo:
von e. Offizier a. D. [d.i. von Henle]
Resumo:
skizziert von O. Lenhard [d.i. Leonhard Freund]
Resumo:
von Ed. Mund [d.i. Edmund Lichtenstein]
Resumo:
napisał C. Omega [d. i. Celestin Zyblikiewicz]
Resumo:
von Sally Simon Tille [d.i. Paul Heichen]
Resumo:
von Sally Simon Tilles [d.i. Paul Heichen]
Resumo:
vom Verf. d. Behemoth [d.i. Andreas Riem]