A simple approach to numerical modelling of propane combustion in fluidized beds

A mathematical model is proposed for the evolution of temperature, chemical composition, and energy release in bubbles, clouds, and emulsion phase during combustion of gaseous premixtures of air and propane in a bubbling fluidized bed. The analysis begins as the bubbles are formed at the orifices of the distributor, until they explode inside the bed or emerge at the free surface of the bed. The model also considers the freeboard region of the fluidized bed until the propane is thoroughly burned. It is essentially built upon the quasi-global mechanism of Hautman et al. (1981) and the mass and heat transfer equations from the two-phase model of Davidson and Harrison (1963). The focus is not on a new modeling approach, but on combining the classical models of the kinetics and other diffusional aspects to obtain a better insight into the events occurring inside a fluidized bed reactor. Experimental data are obtained to validate the model by testing the combustion of commercial propane, in a laboratory-scale fluidized bed, using four sand particle sizes: 400–500, 315–400, 250–315, and 200–250 µm. The mole fractions of CO2, CO, and O2 in the flue gases and the temperature of the fluidized bed are measured and compared with the numerical results.

Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

Kuplivan leijukerroksen poltto- ja lämpötekninen tarkastelu

Työn tavoitteena oli luoda menetelmä leijukerroskattilan petin lämpötilojen ja toiminta-alueen arvioimiseksi annetuilla lähtötiedoilla. Toimintatapana oli tutkia polttoaineen ominaisuuksien ja kattilan geometrian vaikutuksia petin energiataseeseen ja tätä kautta petin lämpötilaan kattilan ajotapa huomioiden. Työn teoriaosassa esitellään aluksi biopolttoaineiden ominaisuuksia ja leijukerroskattilan toimintaa petin toimintaympäristön selvittämiseksi. Teoriaosan lopussa käsitellään perusteellisesti petin hydrodynamiikkaa ja reaktiokinettikkaa sekä petin alueen mekaanista mitoitusta. Lisäksi polttoaineen syöttötapa ja palaminen petissä tuodaan esille. Tutkimusosassa selvitetään petin energiatasemallin määrittämistä teoriaan ja diplomityön aikana eri kattiloilla suoritettuihin mittauksiin perustuen. Mittauksista on erillinen selvitys seitsemännessä kappaleessa. Lopuksi kuvaillaan petin energiatasetta mallintavan menetelmän toimintaa sekä siihen syötettäviä lähtötietoja. Tuloksena on saatu suppealla alueella toimiva laajennettavissa oleva petin energiataseen malli. Menetelmän testaamiseen käytetään mittaustietoa kahdelta kattilalta, joita ei olla käytetty petin energiatasemallin virityksessä.

Polttoaineen reaktiivisuuden määrittäminen kiertoleijupoltossa

Kehitettäessä leijupolttotekniikkaa entistä ympäristöystävällisemmäksi ja tehokkaammaksi tarvitaan lisää tietoa polttoaineen käyttäytymisestä tulipesässä. Polttoaineen palamisprofiili ja reaktiivisuus vaikuttavat oleellisesti esimerkiksi voimalaitoskattilan lämmönsiirtopintojen sijoitteluun ja suunnitteluun sekä ohjausjärjestelmän toteutukseen. Varsinkin monipolttoainekattiloilla ohjausjärjestelmän toimivuus joutuu koetukselle esimerkiksi kuormanmuutostilanteissa ja äkillisissä polttoaineen syöttöhäiriöissä. Tässä työssä on aluksi tutustuttu kiertoleijupolton ilmiöihin ja niiden matemaattiseen mallintamiseen. Lisäksi esitetään katsaus eri prosessiolosuhteiden vaikutuksesta palamiseen kiertoleijuolosuhteissa. Työn tutkimusosassa kehitettiin menetelmä polttoaineen reaktiivisuuden määrittämiseksi kiertoleijupoltossa. Kehitetty menetelmä koostuu koesarjasta ja matemaattisesta simulointimallista. Koetoiminta suoritettiin VTT Energian laboratoriokokoluokan kiertoleijukoelaitteella. Koesarja polttoaineen reaktiivisuuden määrittämiseksi sisältää eri kaasukomponenttien profiilimittauksia ja dynaamisia muutoskokeita. Menetelmän avulla voidaan tutkia eri polttoaineiden reaktiivisuuksia sekä polttoaineen reaktiivisuuden ja tietyn prosessiolosuhteen välistä riippuvuutta. Suorittamalla koeajomatriisin mukaiset kokeet tietyissä prosessiolosuhteissa voidaan polttoaineen reaktiivisuus selvittää koetulosten ja simulointimallin perusteella.

Jäännöshiilen ja kalkkikiven reaktiokinetiikan mallinnus kiertoleijukattilan tulipesässä

Työn tavoitteena oli kehittää mallit jäännöshiilen ja kalkkikiven reaktiokinetiikan sekä jäännöshiilen jauhautumisen ennustamiseksi kiertoleijukattilan tulipesässä. Kehitetyt mallit toimivat tulipesämallin osamalleina. Perustuen mallinnettuihin reaktionopeuksiin ja jauhautumiskäyttäytymiseen tulipesämalli ennustaa kalkkikivihiukkasten rikinsidonnan ja jäännöshiilen jakautumisen erikokoisiksi hiukkasiksi tulipesässä ja tuhkissa. Työssä kehitetyt mallit perustuvat olemassa oleviin kalkkikiven ja polttoaineen reaktiivisuustesteihin laboratorio-kokoluokan leijukerrosreaktorissa. Mallit huomioivat myös tulipesän olosuhteet. Menetelmät kelpoistettiin onnistuneesti kaupallisen kokoluokan kiertoleijukattiloista mitattujen ja tulipesämallilla laskettujen taseiden avulla. Mallien kehittämistä tullaan jatkamaan.

Kerrosleijukattilan polttoaineensyötön ja ilmasäätöjen tutkiminen

Tässä tutkimuksessa käsitellään kerrosleijukattilan kiinteän polttoaineen syöttöjärjestelmän toimintaa ja ilmanjaon vaikutusta kattilan toimintaan. Polttoainejärjestelmän tutkimisessa arvioidaan eri tekijöiden merkitystä höyrynkehityksen huojunnan aiheuttajana. Työllä pyritään tuomaan selvyyttä polttoainejärjestelmän toiminnallisiin peruskysymyksiin kuten turpeen ja kuoren väliseen lajittumiseen, ruuvipurkaukseen ja määrämittauksiin. Työssä esitetään parannusehdotus polttoaineensyötön toiminnan tasoittamiseksi. Ilmasäätöjen osalta on keskitytty tutkimaan erityisesti ilmakanavarakenteiden vaikutusta ilman jakautumiseen. Kattilan ongelmana olivat vasemman ja oikean puolen väliset erot savukaasujen O2-pitoisuuksissa, tulistuslämpötiloissa ja lieriön pinnan korkeudessa. Ilmanjakoon tehtyjen muutosten vaikutuksesta kyseiset erot tasoittuivat huomattavasti. Työssä on lisäksi tarkasteltu mahdollisuuksia kattilan ilmapäästöarvojen parantamiseen erityisesti NOx- ja CO- päästöjen osalta.

Influence of mixed fuels combustion on boiler operation

The aim of this work is to study the effect of different fuel mixtures on the operation of circulating fluidized bed (CFB) boiler. The applicability of heat balance modeling software IPSEpro to simulate CFB boiler operation is also investigated. The work discusses various types of boilers and methods of boiler operation. The fuel properties and the possible fuel influence on the boiler efficiency are described. Various biofuel types that are possible to use in combination with other fuels are presented. Some examples of the fuel mixtures use are given. A CFB boiler model has been constructed using IPSEpro and applied to analyze boiler operation outside design conditions. In the simulations, the effect of different load levels and moisture contents for the fuel mixture has been studied.

Analysis and validation of space averaged drag model for numerical simulations of gas-solid flows in fluidized beds

This thesis presents an approach for formulating and validating a space averaged drag model for coarse mesh simulations of gas-solid flows in fluidized beds using the two-fluid model. Proper modeling for fluid dynamics is central in understanding any industrial multiphase flow. The gas-solid flows in fluidized beds are heterogeneous and usually simulated with the Eulerian description of phases. Such a description requires the usage of fine meshes and small time steps for the proper prediction of its hydrodynamics. Such constraint on the mesh and time step size results in a large number of control volumes and long computational times which are unaffordable for simulations of large scale fluidized beds. If proper closure models are not included, coarse mesh simulations for fluidized beds do not give reasonable results. The coarse mesh simulation fails to resolve the mesoscale structures and results in uniform solids concentration profiles. For a circulating fluidized bed riser, such predicted profiles result in a higher drag force between the gas and solid phase and also overestimated solids mass flux at the outlet. Thus, there is a need to formulate the closure correlations which can accurately predict the hydrodynamics using coarse meshes. This thesis uses the space averaging modeling approach in the formulation of closure models for coarse mesh simulations of the gas-solid flow in fluidized beds using Geldart group B particles. In the analysis of formulating the closure correlation for space averaged drag model, the main parameters for the modeling were found to be the averaging size, solid volume fraction, and distance from the wall. The closure model for the gas-solid drag force was formulated and validated for coarse mesh simulations of the riser, which showed the verification of this modeling approach. Coarse mesh simulations using the corrected drag model resulted in lowered values of solids mass flux. Such an approach is a promising tool in the formulation of appropriate closure models which can be used in coarse mesh simulations of large scale fluidized beds.

Gas-solid two-phase flow in the riser of circulating fluidized beds: mathematical modelling and numerical simulation

A mathematical model is developed for gas-solids flows in circulating fluidized beds. An Eulerian formulation is followed based on the two-fluids model approach where both the fluid and the particulate phases are treated as a continuum. The physical modelling is discussed, including the formulation of boundary conditions and the description of the numerical methodology. Results of numerical simulation are presented and discussed. The model is validated through comparison to experiment, and simulation is performed to investigate the effects on the flow hydrodynamics of the solids viscosity.

Heterogeneous mass transfer in fluidized beds by computational fluid dynamics

The main objective of this research is to estimate and characterize heterogeneous mass transfer coefficients in bench- and pilot-scale fluidized bed processes by the means of computational fluid dynamics (CFD). A further objective is to benchmark the heterogeneous mass transfer coefficients predicted by fine-grid Eulerian CFD simulations against empirical data presented in the scientific literature. First, a fine-grid two-dimensional Eulerian CFD model with a solid and gas phase has been designed. The model is applied for transient two-dimensional simulations of char combustion in small-scale bubbling and turbulent fluidized beds. The same approach is used to simulate a novel fluidized bed energy conversion process developed for the carbon capture, chemical looping combustion operated with a gaseous fuel. In order to analyze the results of the CFD simulations, two one-dimensional fluidized bed models have been formulated. The single-phase and bubble-emulsion models were applied to derive the average gas-bed and interphase mass transfer coefficients, respectively. In the analysis, the effects of various fluidized bed operation parameters, such as fluidization, velocity, particle and bubble diameter, reactor size, and chemical kinetics, on the heterogeneous mass transfer coefficients in the lower fluidized bed are evaluated extensively. The analysis shows that the fine-grid Eulerian CFD model can predict the heterogeneous mass transfer coefficients quantitatively with acceptable accuracy. Qualitatively, the CFD-based research of fluidized bed process revealed several new scientific results, such as parametrical relationships. The huge variance of seven orders of magnitude within the bed Sherwood numbers presented in the literature could be explained by the change of controlling mechanisms in the overall heterogeneous mass transfer process with the varied process conditions. The research opens new process-specific insights into the reactive fluidized bed processes, such as a strong mass transfer control over heterogeneous reaction rate, a dominance of interphase mass transfer in the fine-particle fluidized beds and a strong chemical kinetic dependence of the average gas-bed mass transfer. The obtained mass transfer coefficients can be applied in fluidized bed models used for various engineering design, reactor scale-up and process research tasks, and they consequently provide an enhanced prediction accuracy of the performance of fluidized bed processes.

Puu- ja turvetuhkan hyötykäyttökelpoisuuteen vaikuttavat tekijät pienillä polttolaitoksilla

Energiantuotannossa syntyvä tuhka voi olla laadultaan hyvin vaihtelevaa ja laadunvaihtelulle on haastavaa löytää yksiselitteistä syy-seuraussuhdetta. Ympäristönsuojelulainsäädäntö ja taloudelliset intressit ohjaavat tuhkantuottajia etsimään tuhkalle sopivia hyötykäyttökohteita, ja sen vuoksi tuhkan laatuun ja hyötykäyttökelpoisuuteen vaikuttavia tekijöitä on tarpeen selvittää. Tässä diplomityössä on tutkittu pienissä, alle 50 MW:n polttolaitoksissa syntyvää tuhkaa. Tavoitteena oli selvittää, kuinka tuhkan hyötykäyttökelpoisuuteen voidaan vaikuttaa. Tutkimuksen kohteena oli polttoainekoostumuksen, poltto-olosuhteiden ja tuhkan jälkikäsittelyn vaikutus tuhkassa olevien haitta-aineiden pitoisuuksiin ja liukoisuuksin. Työhön sisältyi myös aiemmin tehtyjen tuhka-analyysien tarkastelu sekä tuhkakokeet kahdella kohderyhmään kuuluvalla laitoksella. Työssä todettiin lentotuhkan haitta-ainepitoisuuksien ja -liukoisuuksien olevan keskimäärin korkeampia kuin pohjatuhkan vastaavien, ja että tyypillisesti arinakattilan tuhkien haitta-aineet ylittävät useammin hyötykäyttökelpoisuuden raja-arvoja kuin kuplaleijupetikattilan tuhkien. Lisäksi havaittiin metsätähdehaketuhkan kelpaavan useammin hyötykäyttöön kuin rankahaketuhkan.

Reducing auxiliary power of a fluid bed boiler island

The aim of this thesis is to find and analyze different methods which reduce fluid bed boilers’ auxiliary power consumption. The objective is to examine the effects and feasibility of these methods. The literature part explains how fluid bed boilers work and what are the main sources of auxiliary power consumption. Designs and operation of these equipment are presented. The literature part also discusses the basics of auxiliary power consumption reduction and introduces four low pressure drop constructions. The experimental part inspects six different methods. Effects of these methods on the auxiliary power consumption are calculated and their impacts on the operation of the boiler are modeled. Calculations show that reasonable changes can reduce fluid bed boiler’s auxiliary power consumption by 2,1-10,2 %. Biggest reductions come from lower air coefficients, smaller bed a-level pressures and lower primary/secondary air –ratios. Models showed no problems with the smaller bed a-level pressures. With the lower air coefficients and smaller primary/secondary air –ratios the models showed a significant increase in the carbon monoxide levels.

Co-fuelling of peat with meat and bone meal in a pilot scale bubbling bed reactor

Co-combustion performance trials of Meat and Bone Meal (MBM) and peat were conducted using a bubbling fluidized bed (BFB) reactor. In the combustion performance trials the effects of the co-combustion of MBM and peat on flue gas emissions, bed fluidization, ash agglomeration tendency in the bed and the composition and quality of the ash were studied. MBM was mixed with peat at 6 levels between 15% and 100%. Emissions were predominantly below regulatory limits. CO concentrations in the flue gas only exceeded the 100 mg/m3 limit upon combustion of pure MBM. SO2 emissions were found to be over the limit of 50 mg/m3, while in all trials NOx emissions were below the limit of 300 mg/m3. The HCl content of the flue gases was found to vary near the limit of 30 mg/m3. VOCs however were within their limits. The problem of bed agglomeration was avoided when the bed temperature was about 850 °C and only 20% MBM was co-combusted. This study indicates that a pilot scale BFB reactor can, under optimum conditions, be operated within emission limits when MBM is used as a co-fuel with peat. This can provide a basis for further scale-up development work in industrial scale BFB applications

Flowback of solids through distribution plates of gas fluidized beds and associated phenomena

This work is concerned with a study of certain phenomena related to the performance and design of distributors in gas fluidized beds with particular regard to flowback of solid particles. The work to be described is divided into two parts. I. In Part one, a review of published material pertaining to distribution plates, including details from the patent specifications, has been prepared. After a chapter on the determination of the incipient fluidizing velocity, the following aspects of multi-orifice distributor plates in gas fluidized beds have been studied: (i) The effect of the distributor on bubble formation related to the way in which even distribution of bubbles on the top surface of the fluidized bed is obtained, e.g. the desirable pressure drop ratio ?PD/?PB for the even distribution of gas across the bed. Ratios of distributor pressure drop ?PD to bed pressure drop at which stable fluidization occurs show reasonable agreement with industrial practice. There is evidence that larger diameter beds tend to be less stable than smaller diameter beds when these are operated with shallow beds. Experiments show that in the presence of the bed the distributor pressure drop is reduced relative to the pressure drop without the bed, and this pressure drop in the former condition is regarded as the appropriate parameter for the design of the distributor. (ii) Experimental measurements of bubble distribution at the surface has been used to indicate maldistribution within the bed. Maldistribution is more likely at low gas flow rates and with distributors having large fractional free area characteristics (i.e. with distributors having low pressure drops). Bubble sizes obtained from this study, as well as those of others, have been successfully correlated. The correlation produced implies the existence of a bubble at the surface of an orifice and its growth by the addition of excess gas from the fluidized bed. (iii) For a given solid system, the amount of defluidized particles stagnating on the distributor plate is influenced by the orifice spacing, bed diameter and gas flow rate, but independent of the initial bed height and the way the orifices are arranged on the distributor plate. II. In Part two, solids flowback through single and multi-orifice distributors in two-dimensional and cylindrical beds of solids fluidized with air has been investigated. Distributors equipped with long cylindrical nozzles have also been included in the study. An equation for the prediction of free flowback of solids through multi-orifice distributors has been derived. Under fluidized conditions two regimes of flowback have been differentiated, namely Jumping and weeping. Data in the weeping regime have been successfully correlated. The limiting gas velocity through the distributor orifices at which flowback is completely excluded is found to be indepnndent of bed height, but a function of distributor design and physical properties of gas and solid used. A criterion for the prediction of this velocity has been established. The decisive advantage of increasing the distributor thickness or using nozzles to minimize solids flowback in fluidized beds has been observed and the opportunity taken to explore this poorly studied subject area. It has been noted, probably for the first time, that with long nozzles, there exists a critical nozzle length above which uncontrollable downflow of solids occurs. A theoretical model for predicting the critical length of a bundle of nozzles in terms of gas velocity through the nozzles has been set up. Theoretical calculations compared favourably with experiments.

Total solution of Gibilaro and Rowe model for a segregating fluidised bed

This study re-examines the one-dimensional equilibrium model of Gibilaro and Rowe (1974) for a segregating gas fluidized bed. The model was based on volumetric jetsam concentration and divided the bed contents into bulk and wake phases, taking account of bulk and wake flux, segregation, exchange between the bulk and wake phases, and axial mixing. Due to the complex nature of the model and its unstable solution, the lack of computing power at the time prevented the authors from doing little more than the analytical solutions to specific cases of this model. This paper provides a numerical total solution and allows the effect of the respective parameters to be compared for the first time. There is also a comparison with experimental results, which showed a reasonable agreement.