Field and Laboratory Tests of Flow-Proportional Passive Samplers for Determining Average Phosphorus and Nitrogen Concentration in Rivers

Flow responsive passive samplers offer considerable potential in nutrient monitoring in catchments; bridging the gap between the intermittency of grab sampling and the high cost of automated monitoring systems. A commercially available passive sampler was evaluated in a number of river systems encapsulating a gradient in storm response, combinations of diffuse and point source pressures, and levels of phosphorus and nitrogen concentrations. Phosphorus and nitrogen are sequestered to a resin matrix in a permeable cartridge positioned in line with streamflow. A salt tracer dissolves in proportion to advective flow through the cartridge. Multiple deployments of different cartridge types were undertaken and the recovery of P and N compared with the flow-weighted mean concentration (FWMC) from high-resolution bank-side analysers at each site. Results from the passive samplers were variable and largely underestimated the FWMC derived from the bank-side analysers. Laboratory tests using ambient river samples indicated good replication of advective throughflow using pumped water, although this appeared not to be a good analogue of river conditions where flow divergence was possible. Laboratory tests also showed good nutrient retention but not elution and these issues appeared to combine to limit the utility in ambient river systems at the small catchment scale.

Improved diffusive gradients in thin films (DGT) measurement of total dissolved inorganic arsenic in waters and soils using a hydrous zirconium oxide binding layer

Abstract Image

A high-capacity diffusive gradients in thin films (DGT) technique has been developed for measurement of total dissolved inorganic arsenic (As) using a long shelf life binding gel layer containing hydrous zirconium oxide (Zr-oxide). Both As(III) and As(V) were rapidly accumulated in the Zr-oxide gel and could be quantitatively recovered by elution using 1.0 M NaOH for freshwater or a mixture of 1.0 M NaOH and 1.0 M H2O2 for seawater. DGT uptake of As(III) and As(V) increased linearly with deployment time and was independent of pH (2.0–9.1), ionic strength (0.01–750 mM), the coexistence of phosphate (0.25–10 mg P L–1), and the aging of the Zr-oxide gel up to 24 months after production. The capacities of the Zr-oxide DGT were 159 μg As(III) and 434 μg As(V) per device for freshwater and 94 μg As(III) and 152 μg As(V) per device for seawater. These values were 5–29 times and 3–19 times more than those reported for the commonly used ferrihydrite and Metsorb DGTs, respectively. Deployments of the Zr-oxide DGT in As-spiked synthetic seawater provided accurate measurements of total dissolved inorganic As over the 96 h deployment, whereas ferrihydrite and Metsorb DGTs only measured the concentrations accurately up to 24 and 48 h, respectively. Deployments in soils showed that the Zr-oxide DGT was a reliable and robust tool, even for soil samples heavily polluted with As. In contrast, As in these soils was underestimated by ferrihydrite and Metsorb DGTs due to insufficient effective capacities, which were likely suppressed by the competing effects of phosphate.

A rapid HPLC protocol for detection of polyols and trehalose

A procedure was developed to extract polyols and trehalose (protectants against stress) from fungal conidia. Conidia were sonicated (120 s) and immersed in a boiling water bath (5.5 min) to optimize extraction of polyols and trehalose, respectively. A rapid method was developed to separate and detect low-molecular-weight polyols and trehalose using high-performance liquid chromatography (HPLC). An ion exchange column designed for standard carbohydrate analysis was used in preference to one designed for sugar alcohol separation. This resulted in rapid elution (less than 5 min), without sacrificing peak resolution. The use of a pulsed electrochemical detector (gold electrode) resulted in limits of reliable quantification as low as 1.6 μg ml-1 for polyols and 2.8 μg ml-1 for trehalose. This is very sensitive and rapid method by which these protectants can be analysed. It avoids polyol derivatization that characterizes analysis by gas chromatography and the long run times (up to 45 min) that typify HPLC analysis using sugar alcohol columns.

Extracção supercrítica de óleo de grainha de uva combinada com pré-tratamentos enzimáticos

Neste trabalho estudou-se a extracção supercrítica do óleo de grainha de uva, usando dióxido de carbono, e combinou-se este processo com um prétratamento enzimático da semente para aumentar o rendimento global da extracção. A qualidade dos extractos obtidos foi avaliada pelo seu conteúdo em triacilglicerídeos, perfil de ácidos gordos e capacidade antioxidante. Realizaram-se também alguns estudos exploratórios sobre a aplicação de um pré-tratamento de alta pressão (HPP) à grainha da uva. Adicionalmente, efectuou-se o estudo da extracção, fraccionamento e caracterização estrutural das procianidinas da grainha da uva, bem como a avaliação da sua capacidade antioxidante. A extracção de procianidinas da grainha da uva foi efectuada sequencialmente com metanol e acetona/água, tendo sido posteriormente fraccionadas por adição sucessiva de misturas metanol/clorofórmio progressivamente mais concentradas em clorofórmio. A caracterização das procianidinas foi feita por HPLC-UV e LC–MS, antes e depois de sujeitar as amostras a uma tiólise, e também por ESI-MS e ESI-MS/MS. Este estudo permitiu reportar, pela primeira vez, a ocorrência de procianidinas do tipo-A galoiladas na grainha da uva. Os resultados de HPLC-UV permitiram determinar o grau médio de polimerização das procianidinas e a sua composição monomérica em (+)- catequina, (-)-epicatequina e (-)-epicatequina-O-galato. Mostrou-se que a (+)- catequina é o flavan-3-ol terminal mais abundante e a (-)-epicatequina predomina largamente como unidade de extensão. No caso de procianidinas do tipo A, a ligação interflavânica C2-C7 encontra-se essencialmente nas unidades terminais. O grau médio de polimerização das diversas fracções varia entre 1.0 e 10.8. A sua capacidade antioxidante, medida pelo método espectrofotométrico de DPPH•, mostrou-se ser equivalente à de uma amostra comercial de (+)-catequina usada como referência. A partir dos graus médios de polimerização experimentais e das análises de FTIR das fracções correspondentes foi possível obter um modelo preditivo O-PLS com apenas uma variável latente. O pré-tratamento enzimático justificou-se pelo conhecimento existente acerca do uso de enzimas específicas que destroem parcialmente as paredes celulares. Atendendo à composição das paredes celulares da grainha da uva preparou-se uma suspensão contendo protease, xilanase, pectinase e celulase. Para determinar as condições experimentais do pré-tratamento que maximizam o rendimento da extracção, estudou-se o efeito do tempo de reacção, temperatura, pH, diâmetro médio das partículas de grainha moída e a concentração das enzimas. Os incrementos do rendimento da extracção de óleo observados atingiram 163.2%. O estudo da extracção supercrítica (SFE) do óleo da grainha de uva tratada e não-tratada permitiu obter as curvas de extracção correspondentes, bem com analisar a influência das condições operatórias sobre o seu andamento. Montou-se uma instalação laboratorial onde se realizaram experiências com dióxido de carbono a 160, 180, 200 e 220 bar e temperaturas de 313.15 e 323.15 K. Os rendimentos obtidos por SFE foram semelhantes aos de Soxhlet com n-hexano. As curvas de extracção medidas compreendem um primeiro período de extracção, onde se remove cerca de 92-97% do óleo disponível, e um segundo período, essencialmente difusional, com pouco impacto no rendimento final. Os vários extractos recolhidos e o óleo global obtido foram caracterizados para avaliar a sua qualidade e relacioná-la com as condições operatórias de SFE. Determinaram-se o conteúdo total em triacilglicerídeos, o seu perfil de ácidos gordos e a capacidade antioxidante (AOC). Os resultados mostraram que a AOC aumenta com a elevação da pressão e, acentuadamente, com o acréscimo da temperatura. Ao longo da curva de extracção, a AOC é mais pronunciada nos extractos iniciais, nomeadamente nos primeiros 30 a 40% da extracção. A modelação efectuada considerou que o óleo extractável se reparte entre células rompidas, predominantes na periferia da semente, e células intactas, mais interiores. Admitiu-se que o transporte de massa ocorre em série, i.e. das células intactas para as rompidas e destas para o solvente; mostrou-se que a dispersão axial era desprezável. Os balanços materiais à fase fluida e aos volumes de células rompidas e intactas, combinados com os fluxos interno, externo e a relação de equilíbrio foram resolvidos numericamente pelo método das linhas combinado com diferenças finitas atrasadas. O modelo reproduziu bem as curvas experimentais e permitiu simular curvas de eluição e os três perfis de concentração no leito.

Production and characterisation of gilthead sea bream (Sparus auratus) recombinant parathyroid hormone related protein.

The production and puriWcation of gilthead sea bream recombinant parathyroid hormone related protein [sbPTHrP(1–125)] using an Escherichia coli system and one step puriWcation process with continuous elution gel electrophoresis is reported. The cDNA encoding sbPTHrP(1–125) was cloned into a prokaryotic expression vector pET-11a. The recombinant plasmid was used to transfect E. coli BL21(DE3) pLysS and sbPTHrP(1–125) synthesis was induced by addition of 1mM isopropyl- -D-thiogalactopyranoside. The rapid one step isolation method gave pure sbPTHrP(1–125) as judged by SDS–PAGE and yielded up to 40mg/L of culture medium (3.3mg protein/g of bacteria). The bioactivity of recombinant sbPTHrP(1–125) assessed using an in vitro scale bioassay was found to be equipotent to PTHrP(1–34) in stimulating cAMP accumulation. Assessment of the immunological reactivity of the isolated protein by Western blot revealed it cross-reacts with antisera speciWc for the N-terminal and C-terminal region of PTHrP. In a radioimmunoassay speciWc for piscine N-terminal (1–34 aa) PTHrP, the recombinant sbPTHrP(1–125) was equipotent with PTHrP(1–34) in displacing labelled 125I-PTHrP(1–36) PTHrP from the antisera. The availability of recombinant sbPTHrP will allow the development of region speciWc assays and studies aimed at deWning post-secretory processing of this protein and its biological activity in Wsh.

Validação de um método de cromatografia de alta eficiência para determinação de conservantes em géneros alimentícios

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química e Biológica

Carcinoembryonic antigen (CEA) in non digestive cancerous and normal tissues.

Carcinoembryonic antigen (CEA), immunologically identical to CEA derived from colonic carcinoma, was identified and purified from perchloric acid (PCA) extracts of bronchial and mammary carcinoma. CEA extracted from bronchial and mammary carcinoma was quantitated by single radial immunodiffusion and was found to be in average about 50-75 times less abundant in these tumors than in colonic carcinoma. CEA could also be detected in one normal breast in lactation and at lower concentrations in normal lung (1000-4000 times lower than in colonic carcinoma). The small amounts of CEA present in normal tissues are distinct from the glycoprotein of small mol. wt showing only partial identity with CEA, that we recently identified and extracted in much larger quantities from normal lung and spleen. The demonstration of the presence of CEA in non digestive carcinoma by classical gel precipitation analysis suggests that the CEA detected in the plasma of such patients by radioimmunoassay is also identical to colonic carcinoma CEA. Our comparative study of plasma CEA from bronchial and colonic carcinoma, showing that CEA from both types of patient has the same elution pattern on Sephadex G-200 and gives parallel inhibition curves in the radioimmunoassay, is in favor of this hypothesis. However, it should not be concluded that all positive CEA radioimmunoassay indicate the presence of an antigen identical to colonic carcinoma CEA. A word of warning concerning the interpretation of radioimmunoassay is required by the observation that the addition of mg amounts of PCA extract of normal plasma, cleared of CEA by Sephadex filtration, could interfere in the test and mimic the presence of CEA.

Rapid high-performance liquid chromatographic determination with fluorescence detection of furosemide in human body fluids and its confirmation by gas chromatography-mass spectrometry.

Furosemide (FD: Lasix) is a loop diuretic which strongly increases both urine flow and electrolyte urinary excretion. Healthy volunteers were administered 40 mg orally (dissolved in water) and concentrations of FD were determined in serum and urine for up to 6 h for eight subjects, who absorbed water at a rate of 400 ml/h. Quantification was performed by HPLC with fluorescence detection (excitation at 233 nm, emission at 389 nm) with a limit of detection of 5 ng/ml for a 300-microliters sample. The elution of FD was completed within 4 min using a gradient of acetonitrile concentration rising from 30 to 50% in 0.08 M phosphoric acid. The delay to the peak serum concentration ranged from 60 to 120 min. FD was still easily measurable in the sera from all subjects 6 h after administration. In urine, the excretion rates reached their maximum between 1 and 3 h. The total amount of FD excreted in the urine averaged 11.2 mg (range 7.6-14.0 mg), with a mean urine volume of 3024 ml (range 2620-3596 ml). Moreover, the urine density was lower than 1.010 (recommended as an upper limit in doping analysis to screen diuretics) only for 2 h. An additional volunteer was administered 40 mg of FD and his urine was collected over a longer period. FD was still detectable 48 h after intake. Gas chromatography-mass spectrometry with different types of ionization was used to confirm the occurrence of FD after permethylation of the extract. Negative-ion chemical ionization, with ammonia as reactant gas, was found to be the most sensitive method of detection.

Arsenic speciation by ion-exchange chromatography with on- line determination by hydride generation: electronic modification of the D.C. plasma by photon counting

A method using L-cysteine for the determination of arsenous acid (As(III)), arsenic acid (As(V)), monomethylarsonic acid (MMAA), and dimethylarsinic acid (DMAA) by hydride generation was demonstrated. The instrument used was a d.c. plasma atomic emission spectrometer (OCP-AES). Complete recovery was reported for As(III), As(V), and DMAA while 86% recovery was reported for MMAA. Detection limits were determined, as arsenic for the species listed previously, to be 1.2, 0.8, 1.1, and 1.0 ngemL-l, respectively. Precision values, at 50 ngemL-1 arsenic concentration, were f.80/0, 2.50/0, 2.6% and 2.6% relative standard deviation, respectively. The L-cysteine reagent was compared directly with the conventional hydride generation technique which uses a potassium iodide-hydrochloric acid medium. Recoveries using L-cysteine when compared with the conventional method provided the following results: similar recoveries were obtained for As(III), slightly better recoveries were obtained for As(V) and MMAA, and significantly better recoveries for DMAA. In addition, tall and sharp peak shapes were observed for all four species when using L-cysteine. The arsenic speciation method involved separation by ion exchange .. high perfonnance liquid chromatography (HPLC) with on-line hydride generation using the L.. cysteine reagent and measurement byOCP-AES. Total analysis time per sample was 12 min while the time between the start of subsequent runs was approximately 20 min. A binary . gradient elution program, which incorporated the following two eluents: 0.01 and 0.5 mM tri.. sodium citrate both containing 5% methanol (v/v) and both at a pH of approximately 9, was used during the separation by HPLC. Recoveries of the four species which were measured as peak area, and were normalized against As(III), were 880/0, 290/0, and 40% for DMAA, MMAA and As(V), respectively. Resolution factors between adjacent analyte peaks of As(III) and DMAA was 1.1; DMAA and MMAA was 1.3; and MMAA and As(V) was 8.6. During the arsenic speciation study, signals from the d.c. plasma optical system were measured using a new photon-signal integrating device. The_new photon integrator developed and built in this laboratory was based on a previously published design which was further modified to reflect current available hardware. This photon integrator was interfaced to a personal computer through an AID convertor. The .photon integrator has adjustable threshold settings and an adjustable post-gain device.

Investigation of the composition of linear alkylbenzenes with emphasis on the identification and quantitation of some trace compounds using GS/MS system in both electron impact and chemical ionization modes

Linear alkylbenzenes, LAB, formed by the Alel3 or HF catalyzed alkylation of benzene are common raw materials for surfactant manufacture. Normally they are sulphonated using S03 or oleum to give the corresponding linear alkylbenzene sulphonates In >95 % yield. As concern has grown about the environmental impact of surfactants,' questions have been raised about the trace levels of unreacted raw materials, linear alkylbenzenes and minor impurities present in them. With the advent of modem analytical instruments and techniques, namely GCIMS, the opportunity has arisen to identify the exact nature of these impurities and to determine the actual levels of them present in the commercial linear ,alkylbenzenes. The object of the proposed study was to separate, identify and quantify major and minor components (1-10%) in commercial linear alkylbenzenes. The focus of this study was on the structure elucidation and determination of impurities and on the qualitative determination of them in all analyzed linear alkylbenzene samples. A gas chromatography/mass spectrometry, (GCIMS) study was performed o~ five samples from the same manufacturer (different production dates) and then it was followed by the analyses of ten commercial linear alkylbenzenes from four different suppliers. All the major components, namely linear alkylbenzene isomers, followed the same elution pattern with the 2-phenyl isomer eluting last. The individual isomers were identified by interpretation of their electron impact and chemical ionization mass spectra. The percent isomer distribution was found to be different from sample to sample. Average molecular weights were calculated using two methods, GC and GCIMS, and compared with the results reported on the Certificate of Analyses (C.O.A.) provided by the manufacturers of commercial linear alkylbenzenes. The GC results in most cases agreed with the reported values, whereas GC/MS results were significantly lower, between 0.41 and 3.29 amu. The minor components, impurities such as branched alkylbenzenes and dialkyltetralins eluted according to their molecular weights. Their fragmentation patterns were studied using electron impact ionization mode and their molecular weight ions confirmed by a 'soft ionization technique', chemical ionization. The level of impurities present i~ the analyzed commercial linear alkylbenzenes was expressed as the percent of the total sample weight, as well as, in mg/g. The percent of impurities was observed to vary between 4.5 % and 16.8 % with the highest being in sample "I". Quantitation (mg/g) of impurities such as branched alkylbenzenes and dialkyltetralins was done using cis/trans-l,4,6,7-tetramethyltetralin as an internal standard. Samples were analyzed using .GC/MS system operating under full scan and single ion monitoring data acquisition modes. The latter data acquisition mode, which offers higher sensitivity, was used to analyze all samples under investigation for presence of linear dialkyltetralins. Dialkyltetralins were reported quantitatively, whereas branched alkylbenzenes were reported semi-qualitatively. The GC/MS method that was developed during the course of this study allowed identification of some other trace impurities present in commercial LABs. Compounds such as non-linear dialkyltetralins, dialkylindanes, diphenylalkanes and alkylnaphthalenes were identified but their detailed structure elucidation and the quantitation was beyond the scope of this study. However, further investigation of these compounds will be the subject of a future study.

Isolation and partial characterization of a complementary protein from the mycoparasite, Piptocephalis virginiana, which specifically binds to two glycoproteins b and c of the host cell surface

Presence of surface glycoprotein in Piptocephalis virginiana that recognizes the host glycoproteins band c, reported earlier from our laboratory, was detected by immunofluorescence microscopy. Germinated spores of P. virginiana treated with Mortierella pusilla cell wall protein extract, primary antibodies prepared against glycoproteins band c and FITC-goat anti-rabbit IgG conjugate showed fluorescence. This indicated that on the surfaces of the biotrophic mycoparasite P. virginiana , there might be a complementary molecule which recognizes the glycoproteins band c from M. pusilla. Immunobinding analysis identified a glycoprotein of Mr 100 kDa from the mycoparasite which binds with the host glycoproteins band c, separately as well as collectively. Purification of this glycoprotein was achieved by (i) 60% ammonium sulfate precipitation, (ii) followed by heat treatment, and (iii) Sephadex G-IOO gel filtration. The glycoprotein was isolated by preparative polyacrylamide gel electrophoresis by cutting and elution. The purity of the protein ·was ascertained by SDS-PAGE and Western blot analysis. Positive reaction to periodic acid-Schiff reagent revealed the glycoprotein nature of this 100 kDa protein. Mannose was identified as a major sugar component of this glycoprotein by using a BoehringerMannheim Glycan Differentiation Kit. Electrophoretically purified glycoprotein was used to raIse polyclonal antibody in rabbit. The specificity of the antibody was determined by dot-immunobinding test and western-blot analysis. Immunofluorescence mIcroscopy revealed surface localization of the protein on the germ tube of Piptocephalis virginiana. Fluorescence was also observed at the surfaceJ of the germinated spores and hyphae of the host, M. pusilla after treatment with complementary protein from P. virginiana, primary antibody prepared against the complementary protein and FITC-goat anti-rabbit IgG conjugate.

The isolation, partial purification and preliminary characterization of a growth factor from chick embryo brains

Chicl( brain growth factor (CBGF) is a mitogen isolated from embryonic chick brains thought to have a potential role as a trophic factor involved in nerve dependent amphibian limb regeneration. In addition, CBGF stimulates 3H-thymidine incorporation in chick embryo brain astrocytes in vitro. In this study, cultured chick embryo brain non-neuronal cells were employed in a bioassay to monitor CBGF activity throughout various stages of its pllrification. Cell culture and assay conditions were optimized. Nonneuronal cells grew best on collagen-coated culture dishes in complete medium, were most responsive to a growth stimulus [10% fetal bovine serum (FBS)] at the second and third subcultures, and were healthiest when rendered "quiescent" in medium supplemented with 1% FBS. The most effective bioassay conditions consisted of a minimum 14.5 hour "quiescence" time (24 hours was used), a 6 hour "prestimulation" time, and a 24 hour 3H-thymidine labeling time. Four-day subconfluent primary non-neuronal cells consisted of 6.63% GFAP positive cells; as a result cultures were thought to be mainly composed of astroblasts. CBGF was purified from 18-day chick embryo brains by ultrafiltration through Amicon PM-30 and YM-2 membranes, size exclusion chromatography through a Biogel P6 column, and analytical reverse-phase high-performance liquid chromatography (rp-HPLC). The greatest activity resided in rp-HPLC fraction #7 (10 ng/ml) which was as effective as 10% FBS at stimulating 3H-thymidine incorporation in chick embryo brain nonneuronal cells. Although other researchers report the isolation of a mitogenic fraction consisting of 5'-GMP from the embryonic chick brain, UV absorbance spectra, rp-HPLC elution profiles, and fast atom bombardment (FAB) mass spectra indicated that CBGF is neither 5'-GMP nor 51-AMP. 2 Moreover, commercially available 5t-GMP was inhibitory to 3H-thymidine incorporation in the chick non-neuronal cells, while Sf-AMP had no effect. Upon treatment with pronase, the biological activity of fraction P6-3 increased; this increase was nearly 30% greater than what would be expected from a simple additive effect of any mitogenic activity of pronase alone together with P6-3 alone. This may suggest the presence of an inhibitor protein. The bioactive component may be a protein protected by a nucleoside/nucleotide or simply a nucleoside/nucleotide acting alone. While the FAB mass spectrum of rp-HPLC fraction #7 did not reveal molecular weight or sequence information, the ion of highest molecular weight was observed at m/z 1610; this is consistent with previous estimations of CBGF's size. 3

Modulation du cytochrome P450 dans un modèle murin d'insuffisance rénale chronique

Introduction : Les modèles murins sont grandement utilisés dans l’étude des maladies rénales et des pathologies associées. La concentration de la créatinine sérique est un bon indicateur de la filtration glomérulaire et en présence d’insuffisance rénale chronique (IRC), les concentrations de créatinine sérique (et la clairance) reflètent la sévérité de l’IRC. De plus, il a été démontré que l’IRC modifie le métabolisme des médicaments en diminuant l’activité et l’expression des enzymes hépatiques du cytochrome P450 (CYP450). Afin d’étudier la modulation du P450 par l’IRC avec un modèle murin et de confirmer nos résultats chez le rat, nous devons 1) développer un modèle d’IRC chez la souris, 2) mettre au point une technique de dosage des marqueurs de l’IRC et, 3) évaluer l’expression protéique du CYP450 en présence IRC. Matériel et Méthode : Trois modèles chirurgicaux d’IRC chez la souris ont été développés. Une méthode du dosage de la créatinine par chromatographie liquide à haute performance (CLHP) a été mise au point chez la souris et l’expression protéique du P450 a été mesurée par immunobuvardage de type Western. Résultats : Plusieurs paramètres de CLHP comme le pH, la concentration et le débit de la phase mobile modifient le pic d’élution et le temps de rétention de la créatinine. Concernant le modèle expérimental, on observe une perte de poids et une augmentation de la concentration plasmatique de la créatinine chez les souris avec une IRC. De plus, l’expression protéique de plusieurs isoformes du cytochrome P450 est modulée par l’IRC. Nous observons une diminution du CYP 2D de 42% (p < 0,01), du CYP 3A11 de 60% et du CYP 1A de 37% (p <0,01) par rapport aux souris témoins. On ne dénote aucun changement significatif au niveau de l’isoforme 2E1. Conclusion : Il est possible d’induire une insuffisance rénale chronique chez la souris suite à une néphrectomie. La technique de dosage de la créatinine par CLHP est précise et exacte et permet de caractériser la sévérité de l’IRC chez la souris. L’expression protéique du CYP450 est régulée à la baisse dans le foie des souris atteintes d’IRC.

Identification de biomarqueurs protéiques prédictifs et diagnostiques des maladies coronariennes pour une population de souche canadienne-française

Les biomarqueurs plasmatiques constituent des outils essentiels, mais rares, utilisés pour diagnostiquer les maladies, comme les maladies cardiovasculaires (MCV), et stratifier le niveau de risque associé. L’identification de nouveaux biomarqueurs plasmatiques susceptibles d’améliorer le dépistage et le suivi des MCV représente ainsi un enjeu majeur en termes d’économie et de santé publique. Le projet vise à identifier de nouveaux biomarqueurs plasmatiques prédictifs ou diagnostiques des MCV, à déterminer le profil protéomique plasmatique de patients atteints de MCV et à développer des méthodes innovantes d’analyse d’échantillon plasmatique. L’étude a été effectuée sur une large banque de plasma provenant de 1006 individus de souche Canadienne-Française recrutés à différents stades de la MCV et qui ont été suivis sur une période de 5 ans. Des séries de déplétions ont été réalisées afin de dépléter les 14 protéines majoritaires (colonne IgY14TM) de l’échantillon avant son analyse par trois approches effectuées en parallèle: 1) Une chromatographie liquide (LC) en 2 dimensions qui fractionne les protéines selon le point isoélectrique puis selon le degré d’hydrophobicité, via le système PF2D, suivie par une chromatographie liquide couplée avec une spectrométrie de masse en tandem (LC-MS/MS). 2) Une séparation classique sur gel 1D-SDS-PAGE suivie d’une LC-MS/MS; 3) Par une déplétion plus poussée du plasma avec l’utilisation en tandem avec la colonne IgY14TM d’une colonne SupermixTM permettant de dépléter également les protéines de moyenne abondance, suivie d’une séparation sur gel 1D-SDS-PAGE et d’une analyse LC-MS/MS de la portion déplétée (3a) et de la portion liée à la SupermixTM (3b). Les résultats montrent que le système PF2D permet d’identifier plusieurs profils protéiques spécifiques au groupe MCV. Sur un total de 1156 fractions (équivalent à 1172 pics protéiques pour le groupe contrôle et 926 pics pour le groupe MCV) recueillies, 15 fractions (23 pics protéiques) présentaient des différences quantitativement significatives (p<0,05) entre les 2 groupes. De plus, 6 fractions (9 pics) sont uniquement présentes dans un groupe, représentant d’autres signatures protéomiques et biomarqueurs potentiellement intéressants. Les méthodes 2, 3a et 3b ont permis l’identification de 108, 125 et 91 protéines respectivement avec des chevauchements partiels (31% entre la méthode 2 et 3a, 61% entre 2 et 3b et 19% entre 3a et 3b). Les méthodes 2 et 3 ont permis l’identification de 12 protéines qui présentaient des différences quantitatives significatives entre les 2 groupes. L’utilisation de plusieurs approches protéomiques complémentaires nous ont d’ores et déjà permis d’identifier des candidats biomarqueurs des angines instables avec récidive d’infarctus du myocarde (IM).

β-glucosidases from Aspergillus unguis NII 08123: Molecular characterization, properties and applications

Lignocellulosic biomass is probably the best alternative resource for biofuel production and it is composed mainly of cellulose, hemicelluloses and lignin. Cellulose is the most abundant among the three and conversion of cellulose to glucose is catalyzed by the enzyme cellulase. Cellulases are groups of enzymes act synergistically upon cellulose to produce glucose and comprise of endoglucanase, cellobiohydrolase and β-glucosidase. β -glucosidase assumes great importance due to the fact that it is the rate limiting enzyme. Endoglucanases (EG) produces nicks in the cellulose polymer exposing reducing and non reducing ends, cellobiohydrolases (CBH) acts upon the reducing or non reducing ends to liberate cellobiose units, and β - glucosidases (BGL) cleaves the cellobiose to liberate glucose completing the hydrolysis. . β -glucosidases undergo feedback inhibition by their own product- β glucose, and cellobiose which is their substrate. Few filamentous fungi produce glucose tolerant β - glucosidases which can overcome this inhibition by tolerating the product concentration to a particular threshold. The present study had targeted a filamentous fungus producing glucose tolerant β - glucosidase which was identified by morphological as well as molecular method. The fungus showed 99% similarity to Aspergillus unguis strain which comes under the Aspergillus nidulans group where most of the glucose tolerant β -glucosidase belongs. The culture was designated the strain number NII 08123 and was deposited in the NII culture collection at CSIR-NIIST. β -glucosidase multiplicity is a common occurrence in fungal world and in A.unguis this was demonstrated using zymogram analysis. A total 5 extracellular isoforms were detected in fungus and the expression levels of these five isoforms varied based on the carbon source available in the medium. Three of these 5 isoforms were expressed in higher levels as identified by the increased fluorescence (due to larger amounts of MUG breakdown by enzyme action) and was speculated to contribute significantly to the total _- β glucosidase activity. These isoforms were named as BGL 1, BGL3 and BGL 5. Among the three, BGL5 was demonstrated to be the glucose tolerant β -glucosidase and this was a low molecular weight protein. Major fraction was a high molecular weight protein but with lesser tolerance to glucose. BGL 3 was between the two in both activity and glucose tolerance.121 Glucose tolerant .β -glucosidase was purified and characterized and kinetic analysis showed that the glucose inhibition constant (Ki) of the protein is 800mM and Km and Vmax of the enzyme was found to be 4.854 mM and 2.946 mol min-1mg protein-1respectively. The optimumtemperature was 60°C and pH 6.0. The molecular weight of the purified protein was ~10kDa in both SDS as well as Native PAGE indicating that the glucose tolerant BGL is a monomeric protein.The major β -glucosidase, BGL1 had a pH and temperature optima of 5.0 and 60 °C respectively. The apparent molecular weight of the Native protein is 240kDa. The Vmax and Km was 78.8 mol min-1mg protein-1 and 0.326mM respectively. Degenerate primers were designed for glycosyl hydrolase families 1, 3 and 5 and the BGL genes were amplified from genomic DNA of Aspergillus unguis. The sequence analyses performed on the amplicons results confirmed the presence of all the three genes. Amplicon with a size of ~500bp was sequenced and which matched to a GH1 –BGL from Aspergillus oryzae. GH3 degenerate primers producing amplicons were sequenced and the sequences matched to β - glucosidase of GH3 family from Aspergillus nidulans and Aspergillus acculateus. GH5 degenerate primers also gave amplification and sequencing results indicated the presence of GH5 family BGL gene in the Aspergillus unguis genomic DNA.From the partial gene sequencing results, specific as well as degenerate primers were designed for TAIL PCR. Sequencing results of the 1.0 Kb amplicon matched Aspergillus nidulans β -glucosidase gene which belongs to the GH1 family. The sequence mainly covered the N-Terminal region of the matching peptide. All the three BGL proteins ie. BGL1, BGL3 and BGL5 were purified by chromatography an electro elution from Native PAGE gels and were subjected to MALDI-TOF mass spectrometric analysis. The results showed that BGL1 peptide mass matched to . β -glucosidase-I of Aspergillus flavus which is a 92kDa protein with 69% protein coverage. The glucose tolerant β -glucosidase BGL5 mass matched to the catalytic C-terminal domain of β -glucosidase-F from Emericella nidulans, but the protein coverage was very low compared to the size of the Emericella nidulans protein. While comparing the size of BGL5 from Aspergillus unguis, the protein sequence coverage is more than 80%. BGL F is a glycosyl hydrolase family 3 protein.The properties of BGL5 seem to be very unique, in that it is a GH3 β -glucosidase with a very low molecular weight of ~10kDa and at the same time having catalytic activity and glucose 122 tolerance which is as yet un-described in GH β -glucosidases. The occurrence of a fully functional 10kDA protein with glucose tolerant BGL activity has tremendous implications both from the points of understanding the structure function relationships as well as for applications of BGL enzymes. BGL-3 showed similarity to BGL1 of Aspergillus aculateus which was another GH3 β -glucosidase. It may be noted that though PCR could detect GH1, GH3 and GH5 β-glucosidases in the fungus, the major isoforms BGL1 BGL3 and BGL5 were all GH3 family enzymes. This would imply that β-glucosidases belonging to other families may also co-exist in the fungus and the other minor isoforms detected in zymograms may account for them. In biomass hydrolysis, GT-BGL containing BGL enzyme was supplemented to cellulase and the performances of blends were compared with a cocktail where commercial β- glucosidase was supplemented to the biomass hydrolyzing enzyme preparation. The cocktail supplemented with A unguis BGL preparation yielded 555mg/g sugar in 12h compared to the commercial enzyme preparation which gave only 333mg/g in the same period and the maximum sugar yield of 858 mg/g was attained in 36h by the cocktail containing A. unguis BGL. While the commercial enzyme achieved almost similar sugar yield in 24h, there was rapid drop in sugar concentration after that, indicating probably the conversion of glucose back to di-or oligosaccharides by the transglycosylation activity of the BGl in that preparation. Compared this, the A.unguis enzyme containing preparation supported peak yields for longer duration (upto 48h) which is important for biomass conversion to other products since the hydrolysate has to undergo certain unit operations before it goes into the next stage ie – fermentation in any bioprocesses for production of either fuels or chemicals.. Most importantly the Aspergillus unguis BGL preparation yields approximately 1.6 fold increase in the sugar release compared to the commercial BGL within 12h of time interval and 2.25 fold increase in the sugar release compared to the control ie. Cellulase without BGL supplementation. The current study therefore leads to the identification of a potent new isolate producing glucose tolerant β - glucosidase. The organism identified as Aspergillus unguis comes under the Aspergillus nidulans group where most of the GT-BGL producers belong and the detailed studies showed that the glucose tolerant β -glucosidase was a very low molecular weight protein which probably belongs to the glycosyl hydrolase family 3. Inhibition kinetic studies helped to understand the Ki and it is the second highest among the nidulans group of Aspergilli. This has promoted us for a detailed study regarding the mechanism of glucose tolerance. The proteomic 123 analyses clearly indicate the presence of GH3 catalytic domain in the protein. Since the size of the protein is very low and still its active and showed glucose tolerance it is speculated that this could be an entirely new protein or the modification of the existing β -glucosidase with only the catalytic domain present in it. Hydrolysis experiments also qualify this BGL, a suitable candidate for the enzyme cocktail development for biomass hydrolysis