Simulation of wind powered hydraulic heating system

The objective of this master’s thesis was to design and simulate a wind powered hydraulic heating system that can operate independently in remote places where the use of electricity is not possible. Components for the system were to be selected in such a way that the conditions for manufacture, use and economic viability are the as good as possible. Savonius rotor was chosen for wind turbine, due to its low cut in speed and robust design. Savonius rotor produces kinetic energy in wide wind speed range and it can withstand high wind gusts. Radial piston pump was chosen for the flow source of the hydraulic heater. Pump type was selected due to its characteristics in low rotation speeds and high efficiency. Volume flow from the pump is passed through the throttle orifice. Pressure drop over the orifice causes the hydraulic oil to heat up and, thus, creating thermal energy. Thermal energy in the oil is led to radiator where it conducts heat to the environment. The hydraulic heating system was simulated. For this purpose a mathematical models of chosen components were created. In simulation wind data gathered by Finnish meteorological institute for 167 hours was used as input. The highest produced power was achieved by changing the orifice diameter so that the rotor tip speed ratio follows the power curve. This is not possible to achieve without using electricity. Thus, for the orifice diameter only one, the optimal value was defined. Results from the simulation were compared with investment calculations. Different parameters effecting the investment profitability were altered in sensitivity analyses in order to define the points of investment profitability. Investment was found to be profitable only with high average wind speeds.

Ilmajohtojen laserkeilaus Suomessa 2014

Tässä kandidaatintyössä on tarkoituksena selvittää ilmajohtojen lentokuvauksen käyttömahdollisuuksia sähköverkkoyhtiöiden toiminnassa. Ilmajohtojen lentokuvaus on Suomessa ja koko maailmassa vielä varsin vähän hyödynnetty keino esimerkiksi sähköverkkojen huolto- ja kunnossapito tarkastuksissa. Lentokuvauksella tarkoitetaan vielä nykyään vuonna 2014 yleensä helikopterista tehtävää johtokadun 3D-kuvausta ja laserkeilausta. Tulevaisuudessa se voi kuitenkin olla mahdollista tehdä myös muista lentävistä aluksista. Työssä on erityisesti keskitytty lentokuvauksessa tehtävään laserkeilukseen ja 3D-kuvaus on jätetty pienemmälle huomiolle. Lisäksi työssä selvitetään lentokuvauksen taloudellista kannattavuutta sähköverkkoyhtiöille sekä pohditaan lentokuvauksen tulevaisuuden näkymiä.

Iron(III) as Lewis acid catalyst in organosilicon and carbonyl chemistry

Iron is one of the most common elements in the earth’s crust and thus its availability and economic viability far exceed that of metals commonly used in catalysis. Also the toxicity of iron is miniscule, compared to the likes of platinum and nickel, making it very desirable as a catalyst. Despite this, prior to the 21st century, the applicability of iron in catalysis was not thoroughly investigated, as it was considered to be inefficient and unselective in desired transformations. In this doctoral thesis, the application of iron catalysis in combination with organosilicon reagents for transformations of carbonyl compounds has been investigated together with insights into iron catalyzed chlorination of silanes and silanols. In the first part of the thesis, the synthetic application of iron(III)-catalyzed chlorination of silanes (Si-H) and the monochlorination of silanes (SiH2) using acetyl chloride as the chlorine source is described. The reactions proceed under ambient conditions, although some compounds need to be protected from excess moisture. In addition, the mechanism and kinetics of the chlorination reaction are briefly adressed. In the second part of this thesis a versatile methodology for transformation of carbonyl compounds into three different compound classes by changing the conditions and amounts of reagents is discussed. One pot reductive benzylation, reductive halogenation and reductive etherification of ketones and aldehydes using silanes as the reducing agent, halide source or cocatalyst, were investigated. Also the reaction kinetics and mechanism of the reductive halogenation of acetophenone are briefly discussed.

Production of magnesium carbonates from serpentinites for CO2 mineral sequestration : optimisation towards industrial application

Global warming is one of the most alarming problems of this century. Initial scepticism concerning its validity is currently dwarfed by the intensification of extreme weather events whilst the gradual arising level of anthropogenic CO2 is pointed out as its main driver. Most of the greenhouse gas (GHG) emissions come from large point sources (heat and power production and industrial processes) and the continued use of fossil fuels requires quick and effective measures to meet the world’s energy demand whilst (at least) stabilizing CO2 atmospheric levels. The framework known as Carbon Capture and Storage (CCS) – or Carbon Capture Utilization and Storage (CCUS) – comprises a portfolio of technologies applicable to large‐scale GHG sources for preventing CO2 from entering the atmosphere. Amongst them, CO2 capture and mineralisation (CCM) presents the highest potential for CO2 sequestration as the predicted carbon storage capacity (as mineral carbonates) far exceeds the estimated levels of the worldwide identified fossil fuel reserves. The work presented in this thesis aims at taking a step forward to the deployment of an energy/cost effective process for simultaneous capture and storage of CO2 in the form of thermodynamically stable and environmentally friendly solid carbonates. R&D work on the process considered here began in 2007 at Åbo Akademi University in Finland. It involves the processing of magnesium silicate minerals with recyclable ammonium salts for extraction of magnesium at ambient pressure and 400‐440⁰C, followed by aqueous precipitation of magnesium in the form of hydroxide, Mg(OH)2, and finally Mg(OH)2 carbonation in a pressurised fluidized bed reactor at ~510⁰C and ~20 bar PCO2 to produce high purity MgCO3. Rock material taken from the Hitura nickel mine, Finland, and serpentinite collected from Bragança, Portugal, were tested for magnesium extraction with both ammonium sulphate and bisulphate (AS and ABS) for determination of optimal operation parameters, primarily: reaction time, reactor type and presence of moisture. Typical efficiencies range from 50 to 80% of magnesium extraction at 350‐450⁰C. In general ABS performs better than AS showing comparable efficiencies at lower temperature and reaction times. The best experimental results so far obtained include 80% magnesium extraction with ABS at 450⁰C in a laboratory scale rotary kiln and 70% Mg(OH)2 carbonation in the PFB at 500⁰C, 20 bar CO2 pressure for 15 minutes. The extraction reaction with ammonium salts is not at all selective towards magnesium. Other elements like iron, nickel, chromium, copper, etc., are also co‐extracted. Their separation, recovery and valorisation are addressed as well and found to be of great importance. The assessment of the exergetic performance of the process was carried out using Aspen Plus® software and pinch analysis technology. The choice of fluxing agent and its recovery method have a decisive sway in the performance of the process: AS is recovered by crystallisation and in general the whole process requires more exergy (2.48–5.09 GJ/tCO2sequestered) than ABS (2.48–4.47 GJ/tCO2sequestered) when ABS is recovered by thermal decomposition. However, the corrosive nature of molten ABS and operational problems inherent to thermal regeneration of ABS prohibit this route. Regeneration of ABS through addition of H2SO4 to AS (followed by crystallisation) results in an overall negative exergy balance (mainly at the expense of low grade heat) but will flood the system with sulphates. Although the ÅA route is still energy intensive, its performance is comparable to conventional CO2 capture methods using alkanolamine solvents. An energy‐neutral process is dependent on the availability and quality of nearby waste heat and economic viability might be achieved with: magnesium extraction and carbonation levels ≥ 90%, the processing of CO2‐containing flue gases (eliminating the expensive capture step) and production of marketable products.

Pk-yrityksen aurinkovoimalainvestointiin vaikuttavat tekijät

Tutkielman tavoitteena on selvittää pienten ja keskisuurten yritysten aurinkovoimalainvestointiin liittyviä tekijöitä sekä erityispiirteitä. Tutkielmassa pk-yritykset on rajattu alueellisesti Etelä-Suomeen ja tekijöitä tarkastellaan investoinnin sekä päätöksenteon näkökulmasta. Keskeisenä asiana tutkielmassa on aurinkosähkömarkkinoiden nykytila sekä mahdollisuudet. Osatavoitteena on tutkia aurinkosähkön hyödyntämistä ja käyttöönottoa Suomessa sekä luoda aurinkosähkön mahdollisuuksista selkeämpi kokonaiskuva. Tutkielman tutkimusmenetelmänä käytetään laadullista tutkimusta. Tutkielma koostuu teoreettisesta katsauksesta sekä empiirisestä osuudesta. Teoreettinen osuus tarkastelee investointeja ja rahoitusvaihtoehtoja. Empiirinen osuus pitää sisällään kolmen kohdeyrityksen haastattelut. Haastattelut toteutettiin marraskuussa 2015 aurinkosähkömarkkinoilla toimiville ratkaisuntarjoajille. Haastatteluiden avulla kartoitettiin alalla toteutettujen aurinkovoimalainvestointien taustatekijöitä ja erityispiirteitä. Tutkimustuloksina havaittiin selkeitä aurinkovoimalainvestointiin vaikuttavia tekijöitä sekä muutamia erityispiirteitä. Taloudellista kannattavuutta voidaan pitää investointien lähtökohtana. Tähän vaikuttaa uusiutuvan energian investointeihin saatavilla oleva energiatuki, jolla on merkittävä vaikutus pk-yrityksen päätöksentekoon. Lisäksi ekologinen sähkön tuotanto sekä omavaraisuus nousivat haastatteluissa esiin. Johtopäätöksinä voidaan todeta aurinkosähkön sisältävän useita tekijöitä ja erityispiirteitä, joita investoijien sekä ratkaisuntarjoajien tulee ottaa huomioon. Aurinkosähkömarkkinoiden suurta potentiaalia voidaan hyödyntää tehokkaammin kehittämällä alan tiedonjakoa esille nousseiden tekijöiden ja erityispiirteiden osalta.

Les répercussions du plan Marshall sur les comportements économiques du Canada durant la période de l'après-guerre

La période de l’après-guerre posa d’importants défis commerciaux à l’économie canadienne. Les années entre 1945 et 1950 furent effectivement marquées par la rupture de son système commercial traditionnel et la recherche d’une stratégie alternative. Le pays dut composer avec un déficit commercial croissant à l’égard des États-Unis, ainsi qu’une chute de ses exportations à destination du Royaume-Uni, ruiné par les années de guerre. Ce déséquilibre commercial qui menaçait d’épuiser les réserves canadiennes de dollars américains reflétait l’écart entre les capacités productives des deux rives de l’Atlantique. Le programme de reconstruction des économies européennes, ou plan Marshall, fut accueilli avec enthousiasme à Ottawa puisqu’il devait non seulement rétablir les marchés du Vieux Continent, mais également faciliter la mise en place d’un réseau multilatéral d’échanges et la libéralisation du commerce international. Les tensions de la guerre froide limitèrent toutefois l’ouverture de ces marchés aux marchandises canadiennes, puisque l’endiguement du communisme commanda une consolidation européenne qui privilégia le démantèlement des entraves aux échanges intra-européens, aux dépens du commerce transatlantique. Les préoccupations de Washington en matière de sécurité collective devaient néanmoins laisser place à une stratégie alternative pour le Canada, en poussant la coopération économique des deux pays, dans le but d’optimiser une production de défense destinée aux pays membres de l’OTAN, dont la demande était soutenue par l’aide Marshall. L’incorporation du Canada dans ce dispositif de défense élargie à la communauté atlantique permit ainsi d’assurer un accès privilégié à ses marchandises sur le marché américain, et par conséquent de progresser vers l’équilibre commercial.

Economics of Ornamental Fisheries in Kerala

Comprehensive studies integrating production, consumption and marketing of ornamental fishes were never conducted in the past in Kerala and this study is an attempt to highlight the dynamics in a systematic manner by making a primary empirical study. The advantages of such an approach are many. First, the study entails detailed empirical data under a given time frame on various inter linked economic activities in ornamental fisheries sector. Second, the study tries to improve upon the previous discipline-bound studies by adopting an integrated approach. As Kerala has diverse ecological and climatic conditions, case studies on various ornamental fish production systems help identifying suitable culture practice for selected environmental conditions. One of the major conclusions of this study as explained in the concluding chapter is that although Kerala is blessed with favourable geographic and climatic conditions needed for developing ornamental fishery, diverse local conditions and requirements contain adopting modern methods of enterprise development.Consumer studies conducted would help to identify the demand of ornamental fishes and the factors leading to it. Market studies would help in understanding the forces behind domestic market, which is very promising, but neglected. Viability studies throw light on the economic performance of both the production systems and the trading units of ornamental fishes. Despite the economic significance of ornamental fisheries industry, its development has been constrained due to various bio-technical, cultural, socio-economic, organisational and above all, institutional and policy failures. The outcome of the study would identify constraints facing the industry and institutional arrangements for development.

The power of taxation under the indian constitution

The Power Of Taxation Under The lndian Constitution, the subject of the present thesis has a wide ambit covering the entire federal field end deep constitutional significance traversing many of the principles like pith and substance, colourability, severebility etc. However, considerations of time, space and areas already investigated have indicated that the present study may be confined to the fundamental constitutional limitations end the federal problem. Thus the effect of fundamental rights, the commerce clause, immunity of instrumentalitis and the principle limiting the power of legislative delegation on the power of taxation has been studied. The distribution of taxes between the Union and units of the Indian federation leans so much over to the former and that part of this study has been directed to discover what devices can help the units to gain economic viability

Energetics 0f A Few Marine Crustaceans

Success achieved in seed production and culture of prawns induced researchers to explore the feasibiltiy of culture of other important crustaceans like lobsters and crabs. The CMFRI initiated a project to study the prospects of spiny lobster’ culture and I was associated with this project from the beginning. Compared to shrimp farming, culture of spiny lobsters is an entirely different proposition due to inherent problems in producing their seeds. The emphasis on .obster culture, therefore, shifted to rearing of juvenile lobsters, which form a major portion in commercial lobster landings in India. Commendable success was achieved in enhancing growth rate of four important speices of spiny lobsters by bilateral eyestalk ablation. But due to strong reservations expressed against the "blinding" of lobsters by people from all walks of life, this technique could not be tested commercially for its economic viability. As in prawns, energetics of reproduction and egg development have not yet been documented in spiny lobsters and so these aspects were included in this study. Though some limited informations on food conversion efficiency are availble in spiny lobster, a detailed study on the effect of size and sexual maturity on food conversion was wanting and this also was included in this investigation. The most dominant spiny lobster in south east and south west coast of India, Panulirus homarus (Linnaeus) was selected for this study. Uptake, accumulation and utilization of minerals and trace elements are important events during embryogenesis of aquatic invertebrates. The scope of this study was widened to include these aspects also in order to understand how specific requirements of minerals and trace elements are met in the developing eggs of these two species of crustaceans.

Plan de negocios para la creación de una empresa dedicada a la atención, entrenamiento, estética y cuidado de los perros como mascota, ubicada en un centro comercial de la ciudad de Bogotá

Descripción del Negocio Kinderpup es una guardería para perros como mascota ubicada en el centro comercial Unicentro en la ciudad de Bogotá, creada para atender las necesidades de las personas propietarias de éstas mascotas, las cuales presentan inconvenientes al dar un paseo por varios lugares en los cuales no es permitido el acceso de estos animales. Los lugares más comunes son los centros comerciales, y es precisamente por esto que el proyecto se concentra en este tipo de establecimientos. El objetivo es ofrecer tranquilidad y comodidad a los usuarios de nuestros servicios, brindando atención y cariño a sus mascotas y entendiéndolas como parte importante de las familias. Para cumplir con nuestro objetivo, Kinderpup contará con personal calificado siempre dispuesto a prestar servicios de guardería, veterinaria, peluquería y entrenamiento, esenciales para mantener a las mascotas saludables, hermosas y felices. El servicio de peluquería incluye corte de pelo, arreglo de uñas y dientes; entrenamiento, incluye salida a pasear alrededor del centro comercial y adiestramiento por un entrenador capacitado. El servicio veterinario incluye diagnostico, historia clínica del canino, revisión general y recomendaciones. También se cuenta con artículos para la venta, concentrado y productos de estética animal, que podrán ser adquiridos por los usuarios de las mascotas en la sede de Kinderpup. Mercado En Colombia actualmente no existe un espacio adecuado para atender a las mascotas en los centros comerciales, aún se mantiene prohibido el acceso de animales a estos establecimientos y las personas propietarias de mascotas que frecuentan estos lugares plantean la necesidad de proporcionar un espacio para que puedan dejar sus animales allí. Dado a lo que sugiere el mercado potencial y a la localización central del centro comercial Unicentro, se da la oportunidad de ofrecer diferentes servicios además de guardería a las personas de estratos 4, 5 y 6 que frecuentan los centros comerciales y que necesitan un lugar de confianza para dejar a sus mascotas cuando tengan que salir y no los puedan llevar, quieran peluquear a su perro o adiestrarlo. De igual manera, este servicio es muy beneficioso para las personas que viven alrededor del centro comercial debido a que durante la semana tienen la preocupación de dejar a su mascota sola en casa o con una persona inexperta. Según el estudio de mercados, existe un porcentaje interesante de personas que visitan los establecimientos comerciales en fines de semana, el 26% de 100 personas encuestadas asisten al centro comercial entre 2 y 3 veces al mes y el 22%, van 4 veces al mes, además el 44% de los encuestados dicen que el centro comercial de su preferencia es Unicentro y una cifra todavía más significativa es que el 78% de las personas llevarían a su perro al centro comercial si esto no fuera prohibido. Operaciones El ciclo de servicio comienza a partir de que el cliente se acerca a solicitar información en la recepción de Kinderpup, al recibir un volante publicitario o comunicándose con nosotros por teléfono o email. A partir del momento en que las personas deseen dejar su mascota a nuestro cuidado, se procede a un acercamiento con la mascota que le proporcione tranquilidad tanto a la mascota como a su amo y, a continuación se ejecuta el servicio indicado según el caso. Equipo de Gestión El equipo gestor de Kinderpup estará formado por los siguientes integrantes:  Silvia Valencia: Veterinaria, responsable de asesorar sobre el cuidado de las mascotas, las normas de higiene y protección y administrar la guardería.  José Segura: Promotor de ventas encargado de hacer los contactos con las empresas proveedoras, agencias de publicidad y Unicentro.  Ana María Romero: Directora encargada de dirigir a los empleados y de planear las estrategias de mercadeo y competitividad. Viabilidad económica La inversión a realizar es de $47’599.463, financiados en un 60% por una entidad financiera, se asume un incremento en ventas del 4% según la investigación de mercados, además un aumento de los costos y precios en un 3%. Tras este análisis podemos identificar los principales indicadores financieros que nos guiaran en la toma de decisión acerca de la viabilidad del mismo: Los flujos de caja que tenemos para obtener los anteriores indicativos son los siguientes: 2008 2009 2010 2011 2012 2013 $ -47.599.463,20 $ 17.056.542,57 $ 13.744.893,02 $ 25.924.959,20 $ 39.316.390,43 $ 52.499.868,67

Potential for clean yam minisett production by resource-poor farmers in the middle-belt of Nigeria

Yarn minisett technique (YMT) has been promoted throughout West Africa since the 1980s as a sustainable means of producing clean yarn planting material, but adoption of the technique is Often reported as being patchy at best. While there has been much research Oil the factors that influence adoption of the technique, there have been no attempts to assess its economic viability under 'farmer-managed' as distinct from 'on station' conditions. The present paper describes the results of farmer-managed trials employing the YMT (white yarn: Dioscorea rotundata) at two villages in Igalaland, Kogi State, Nigeria. One of the villages (Edeke) is on the banks of the River Niger and represents it specialist yarn environment, whereas the other village (Ekwuloko) is inland, where farmers employ a more general cropping system. Four farmers were selected in each of the two villages and asked to plant a trial comprising two varieties of yam, their popular local variety its well its another variety grown in other parts of Igalaland, and to treat yarn setts (80-100 g) with either woodash or insecticide/nematicide + fungicide mix (chemical treatment). Results suggest that while chemical sett treatment increased yield and hence gross margin compared with woodash, if household labour is costed then YMT is not economically viable. However, the specialist yarn growers of Edeke were far more positive about the use of YMT as they tended to keep the yarn seed tubers for planting rather than sell them. Thus, great care needs to be taken with planning adoption surveys on the assumption that all farmers should adopt a technology.

A comparison of energy use in conventional and integrated arable farming systems in the UK

The LINK Integrated Farming Systems (LINK-IFS) Project (1992-1997) was setup to compare conventional and integrated arable farming systems (IAFS), concentrating on practical feasibility and economic viability, but also taking into account the level of inputs used and environmental impact. As part of this, an examination into energy use within the two systems was also undertaken. This paper presents the results from that analysis. The data used is from the six sites within the LINK-IFS Project, spread through the arable production areas of England and from the one site in Scotland, covering the 5 years of the project. The comparison of the energy used is based on the equipment and inputs used to produce I kg of each crop within the conventional and integrated rotations, and thereby the overall energy used for each system. The results suggest that, in terms of total energy used, the integrated system appears to be the most efficient. However, in terms of energy efficiency, energy use per kilogram of output, the results are less conclusive. (C) 2003 Elsevier Science B.V. All rights reserved.

Saving the planet but losing the landscape: the impact of renewable energy policies on rural Britain

The main instrument of the Government's renewable energy policy is to promote wind power through regulation and subsidy. This gives rise to anomalies in rural planning when turbines are erected in sensitve areas in which other forms of development are strictly controlled. The situation is reviewed in the context of economic viability and considered also against the alternative of growing fuel crops. The latter are currently hampered by lack of Government support but could fulfil a useful secondary role of sustaining the agricultural sector and with it the management of lowland landscapes.

The role of conventional generation in managing variability

As electricity systems incorporate increasing levels of variable renewable generation, conventional plant will be required to operate more flexibly, with potential impacts for economic viability and reliability. Northern Ireland is pursuing an ambitious target of 40% of electricity to be supplied from renewable sources by 2020. The dominant source of this energy is anticipated to come from inherently variable wind power, one of the most mature renewable technologies. Conventional thermal generators will have a significant role to play in maintaining security of supply. However, running conventional generation more flexibly in order to cater for a wind led regime can reduce its efficiency, as well as shortening its lifespan and increasing O&M costs. This paper examines the impacts of variable operation on existing fossil fuel based generators, with a particular focus on Northern Ireland. Access to plant operators and industry experts has provided insight not currently evident in the energy literature. Characteristics of plant operation and the market framework are identified that present significant challenges in moving to the proposed levels of wind penetration. Opportunities for increasing flexible operation are proposed and future research needs identified.

Landscape and farm scale management to enhance biodiversity conservation in the cocoa producing region of southern Bahia, Brazil

In southern Bahia, Brazil, large land areas are used for the production of cocoa (Theobroma cacao), which is predominantly grown under the shade of native trees in an agroforestry system locally known as cabruca. As a dominant forest-like landscape element of the cocoa region, the cabrucas play an important role in the conservation of the region`s biodiversity. The purpose of this review is to provide the scientific basis for an action plan to reconcile cocoa production and biodiversity conservation in southern Bahia. The available research collectively highlights the diversity of responses of different species and biological groups to both the habitat quality of the cabrucas themselves and to the general characteristics of the landscape, such as the relative extent and spatial configuration of different vegetation types within the landscape mosaic. We identify factors that influence directly or indirectly the occurrence of native species in the cabrucas and the wider landscape of the cocoa region and develop recommendations for their conservation management. We show that the current scientific knowledge already provides a good basis for a biodiversity friendly management of the cocoa region of southern Bahia, although more work is needed to refine some management recommendations, especially on shade canopy composition and density, and verify their economic viability. The implementation of our recommendations should be accompanied by appropriate biological and socioeconomic monitoring and the findings should inform a broad program of adaptive management of the cabrucas and the wider cocoa landscape.