Maintenance strategy optimization using a continuous-state partially observable semi-Markov decision process

Due to the limitation of current condition monitoring technologies, the estimates of asset health states may contain some uncertainties. A maintenance strategy ignoring this uncertainty of asset health state can cause additional costs or downtime. The partially observable Markov decision process (POMDP) is a commonly used approach to derive optimal maintenance strategies when asset health inspections are imperfect. However, existing applications of the POMDP to maintenance decision-making largely adopt the discrete time and state assumptions. The discrete-time assumption requires the health state transitions and maintenance activities only happen at discrete epochs, which cannot model the failure time accurately and is not cost-effective. The discrete health state assumption, on the other hand, may not be elaborate enough to improve the effectiveness of maintenance. To address these limitations, this paper proposes a continuous state partially observable semi-Markov decision process (POSMDP). An algorithm that combines the Monte Carlo-based density projection method and the policy iteration is developed to solve the POSMDP. Different types of maintenance activities (i.e., inspections, replacement, and imperfect maintenance) are considered in this paper. The next maintenance action and the corresponding waiting durations are optimized jointly to minimize the long-run expected cost per unit time and availability. The result of simulation studies shows that the proposed maintenance optimization approach is more cost-effective than maintenance strategies derived by another two approximate methods, when regular inspection intervals are adopted. The simulation study also shows that the maintenance cost can be further reduced by developing maintenance strategies with state-dependent maintenance intervals using the POSMDP. In addition, during the simulation studies the proposed POSMDP shows the ability to adopt a cost-effective strategy structure when multiple types of maintenance activities are involved.

Multicast traffic filtering for sampled value process bus networks

Ethernet is a key component of the standards used for digital process buses in transmission substations, namely IEC 61850 and IEEE Std 1588-2008 (PTPv2). These standards use multicast Ethernet frames that can be processed by more than one device. This presents some significant engineering challenges when implementing a sampled value process bus due to the large amount of network traffic. A system of network traffic segregation using a combination of Virtual LAN (VLAN) and multicast address filtering using managed Ethernet switches is presented. This includes VLAN prioritisation of traffic classes such as the IEC 61850 protocols GOOSE, MMS and sampled values (SV), and other protocols like PTPv2. Multicast address filtering is used to limit SV/GOOSE traffic to defined subsets of subscribers. A method to map substation plant reference designations to multicast address ranges is proposed that enables engineers to determine the type of traffic and location of the source by inspecting the destination address. This method and the proposed filtering strategy simplifies future changes to the prioritisation of network traffic, and is applicable to both process bus and station bus applications.

Does venture opportunity variation matter? Investigating systemic process differences between innovative and imitative new ventures

The central thesis in the article is that the venture creation process is different for innovative versus imitative ventures. This holds up; the pace of the process differs by type of venture as do, in line with theory-based hypotheses, the effects of certain human capital (HC) and social capital (SC) predictors. Importantly, and somewhat unexpectedly, the theoretically derived models using HC, SC, and certain controls are relatively successful explaining progress in the creation process for the minority of innovative ventures, but achieve very limited success for the imitative majority. This may be due to a rationalistic bias in conventional theorizing and suggests that there is need for considerable theoretical development regarding the important phenomenon of new venture creation processes. Another important result is that the building up of instrumental social capital, which we assess comprehensively and as a time variant construct, is important for making progress with both types of ventures, and increasingly, so as the process progresses. This result corroborates with stronger operationalization and more appropriate analysis method what previously published research has only been able to hint at.

Online retailing versus traditional stores in the purchasing decision making process

Due to proliferation of online stores prior expectations that retailing would move completely online were not fulfilled. Previous research about consumers’ preference of retailing channels suggested that online sales are driven by the convenience of online shopping, or as a natural extension of online searches. This paradigm has changed over the years. Changes in consumer behaviour are indicating that while consumers are searching online using various information sources to learn about products, ultimately when purchasing, consumers are shifting between online and offline retailing channels depending on various factors. Online shopping is still considered to be a convenient way to purchase goods, but the convenience is not the key factor. This qualitative research is based on 22 in-depth interviews with shoppers in Australia.

Public participation in infrastructure and construction projects in China: From an EIA-based to a whole-cycle process

Many governments world-wide are increasingly encouraging the involvement of interested individuals, groups and organisations in their publicinfrastructure and construction (PIC) projects as a means of improving the openness, transparency and accountability of the decision-making process and help improve the projects’ long-term viability and benefits to the community. In China, however, the current participatory mechanism at the project level exists only as part of the environmental impact assessment (EIA) process. With an increasing demand for PIC projects and social equality in China, this suggests a need to bring the participatory process into line with international practice. The aim of this paper, therefore, is to identify the weaknesses of EIA-basedpublicparticipation in China and the means by which it may be improved for the whole lifecycle of PIC schemes. To do this, the results of a series of interviews with a diverse group of experts is reported which analyse the nature and extent of existing problems of publicparticipation in EIA and suggestions for improvement. These indicate that the current level of participation in PIC projects is quite limited, particularly in the crucial earlier stages, primarily due to traditional culture and values, uneven progress in the adoption of participatory mechanisms, the risk of not meeting targets and lack of confidence in public competence. Finally, aprocess flowchart is proposed to guide construction practitioners and the community in general.

Visual support for work assignment in process-aware information systems : framework formalisation and implementation

Process-aware information systems, ranging from generic workflow systems to dedicated enterprise information systems, use work-lists to offer so-called work items to users. In real scenarios, users can be confronted with a very large number of work items that stem from multiple cases of different processes. In this jungle of work items, users may find it hard to choose the right item to work on next. The system cannot autonomously decide which is the right work item, since the decision is also dependent on conditions that are somehow outside the system. For instance, what is “best” for an organisation should be mediated with what is “best” for its employees. Current work-list handlers show work items as a simple sorted list and therefore do not provide much decision support for choosing the right work item. Since the work-list handler is the dominant interface between the system and its users, it is worthwhile to provide an intuitive graphical interface that uses contextual information about work items and users to provide suggestions about prioritisation of work items. This paper uses the so-called map metaphor to visualise work items and resources (e.g., users) in a sophisticated manner. Moreover, based on distance notions, the work-list handler can suggest the next work item by considering different perspectives. For example, urgent work items of a type that suits the user may be highlighted. The underlying map and distance notions may be of a geographical nature (e.g., a map of a city or office building), but may also be based on process designs, organisational structures, social networks, due dates, calendars, etc. The framework proposed in this paper is generic and can be applied to any process-aware information system. Moreover, in order to show its practical feasibility, the paper discusses a full-fledged implementation developed in the context of the open-source workflow environment YAWL, together with two real examples stemming from two very different scenarios. The results of an initial usability evaluation of the implementation are also presented, which provide a first indication of the validity of the approach.

Hospital outpatient responses to potential driving impairment due to prescribed medications

Driving and using prescription medicines that have the potential to impair driving is an emerging research area. To date it is characterised by a limited (although growing) number of studies and methodological complexities that make generalisations about impairment due to medications difficult. Consistent evidence has been found for the impairing effects of hypnotics, sedative antidepressants and antihistamines, and narcotic analgesics, although it has been estimated that as many as nine medication classes have the potential to impair driving (Alvarez & del Rio, 2000; Walsh, de Gier, Christopherson, & Verstraete, 2004). There is also evidence for increased negative effects related to concomitant use of other medications and alcohol (Movig et al., 2004; Pringle, Ahern, Heller, Gold, & Brown, 2005). Statistics on the high levels of Australian prescription medication use suggest that consumer awareness of driving impairment due to medicines should be examined. One web-based study has found a low level of awareness, knowledge and risk perceptions among Australian drivers about the impairing effects of various medications on driving (Mallick, Johnston, Goren, & Kennedy, 2007). The lack of awareness and knowledge brings into question the effectiveness of the existing countermeasures. In Australia these consist of the use of ancillary warning labels administered under mandatory regulation and professional guidelines, advice to patients, and the use of Consumer Medicines Information (CMI) with medications that are known to cause impairment. The responsibility for the use of the warnings and related counsel to patients primarily lies with the pharmacist when dispensing relevant medication. A review by the Therapeutic Goods Administration (TGA) noted that in practice, advice to patients may not occur and that CMI is not always available (TGA, 2002). Researchers have also found that patients' recall of verbal counsel is very low (Houts, Bachrach, Witmer, Tringali, Bucher, & Localio, 1998). With healthcare observed as increasingly being provided in outpatient conditions (Davis et al., 2006; Vingilis & MacDonald, 2000), establishing the effectiveness of the warning labels as a countermeasure is especially important. There have been recent international developments in medication categorisation systems and associated medication warning labels. In 2005, France implemented a four-tier medication categorisation and warning system to improve patients' and health professionals' awareness and knowledge of related road safety issues (AFSSAPS, 2005). This warning system uses a pictogram and indicates the level of potential impairment in relation to driving performance through the use of colour and advice on the recommended behaviour to adopt towards driving. The comparable Australian system does not indicate the severity level of potential effects, and does not provide specific guidelines on the attitude or actions that the individual should adopt towards driving. It is reliant upon the patient to be vigilant in self-monitoring effects, to understand the potential ways in which they may be affected and how serious these effects may be, and to adopt the appropriate protective actions. This thesis investigates the responses of a sample of Australian hospital outpatients who receive appropriate labelling and counselling advice about potential driving impairment due to prescribed medicines. It aims to provide baseline data on the understanding and use of relevant medications by a Queensland public hospital outpatient sample recruited through the hospital pharmacy. It includes an exploration and comparison of the effect of the Australian and French medication warning systems on medication user knowledge, attitudes, beliefs and behaviour, and explores whether there are areas in which the Australian system may be improved by including any beneficial elements of the French system. A total of 358 outpatients were surveyed, and a follow-up telephone survey was conducted with a subgroup of consenting participants who were taking at least one medication that required an ancillary warning label about driving impairment. A complementary study of 75 French hospital outpatients was also conducted to further investigate the performance of the warnings. Not surprisingly, medication use among the Australian outpatient sample was high. The ancillary warning labels required to appear on medications that can impair driving were prevalent. A subgroup of participants was identified as being potentially at-risk of driving impaired, based on their reported recent use of medications requiring an ancillary warning label and level of driving activity. The sample reported previous behaviour and held future intentions that were consistent with warning label advice and health protective action. Participants did not express a particular need for being advised by a health professional regarding fitness to drive in relation to their medication. However, it was also apparent from the analysis that the participants would be significantly more likely to follow advice from a doctor than a pharmacist. High levels of knowledge in terms of general principles about effects of alcohol, illicit drugs and combinations of substances, and related health and crash risks were revealed. This may reflect a sample specific effect. Emphasis is placed in the professional guidelines for hospital pharmacists that make it essential that advisory labels are applied to medicines where applicable and that warning advice is given to all patients on medication which may affect driving (SHPA, 2006, p. 221). The research program applied selected theoretical constructs from Schwarzer's (1992) Health Action Process Approach, which has extended constructs from existing health theories such as the Theory of Planned Behavior (Ajzen, 1991) to better account for the intention-behaviour gap often observed when predicting behaviour. This was undertaken to explore the utility of the constructs in understanding and predicting compliance intentions and behaviour with the mandatory medication warning about driving impairment. This investigation revealed that the theoretical constructs related to intention and planning to avoid driving if an effect from the medication was noticed were useful. Not all the theoretical model constructs that had been demonstrated to be significant predictors in previous research on different health behaviours were significant in the present analyses. Positive outcome expectancies from avoiding driving were found to be important influences on forming the intention to avoid driving if an effect due to medication was noticed. In turn, intention was found to be a significant predictor of planning. Other selected theoretical constructs failed to predict compliance with the Australian warning label advice. It is possible that the limited predictive power of a number of constructs including risk perceptions is due to the small sample size obtained at follow up on which the evaluation is based. Alternately, it is possible that the theoretical constructs failed to sufficiently account for issues of particular relevance to the driving situation. The responses of the Australian hospital outpatient sample towards the Australian and French medication warning labels, which differed according to visual characteristics and warning message, were examined. In addition, a complementary study with a sample of French hospital outpatients was undertaken in order to allow general comparisons concerning the performance of the warnings. While a large amount of research exists concerning warning effectiveness, there is little research that has specifically investigated medication warnings relating to driving impairment. General established principles concerning factors that have been demonstrated to enhance warning noticeability and behavioural compliance have been extrapolated and investigated in the present study. The extent to which there is a need for education and improved health messages on this issue was a core issue of investigation in this thesis. Among the Australian sample, the size of the warning label and text, and red colour were the most visually important characteristics. The pictogram used in the French labels was also rated highly, and was salient for a large proportion of the sample. According to the study of French hospital outpatients, the pictogram was perceived to be the most important visual characteristic. Overall, the findings suggest that the Australian approach of using a combination of visual characteristics was important for the majority of the sample but that the use of a pictogram could enhance effects. A high rate of warning recall was found overall and a further important finding was that higher warning label recall was associated with increased number of medication classes taken. These results suggest that increased vigilance and care are associated with the number of medications taken and the associated repetition of the warning message. Significantly higher levels of risk perception were found for the French Level 3 (highest severity) label compared with the comparable mandatory Australian ancillary Label 1 warning. Participants' intentions related to the warning labels indicated that they would be more cautious while taking potentially impairing medication displaying the French Level 3 label compared with the Australian Label 1. These are potentially important findings for the Australian context regarding the current driving impairment warnings about displayed on medication. The findings raise other important implications for the Australian labelling context. An underlying factor may be the differences in the wording of the warning messages that appear on the Australian and French labels. The French label explicitly states "do not drive" while the Australian label states "if affected, do not drive", and the difference in responses may reflect that less severity is perceived where the situation involves the consumer's self-assessment of their impairment. The differences in the assignment of responsibility by the Australian (the consumer assesses and decides) and French (the doctor assesses and decides) approaches for the decision to drive while taking medication raises the core question of who is most able to assess driving impairment due to medication: the consumer, or the health professional? There are pros and cons related to knowledge, expertise and practicalities with either option. However, if the safety of the consumer is the primary aim, then the trend towards stronger risk perceptions and more consistent and cautious behavioural intentions in relation to the French label suggests that this approach may be more beneficial for consumer safety. The observations from the follow-up survey, although based on a small sample size and descriptive in nature, revealed that just over half of the sample recalled seeing a warning label about driving impairment on at least one of their medications. The majority of these respondents reported compliance with the warning advice. However, the results indicated variation in responses concerning alcohol intake and modifying the dose of medication or driving habits so that they could continue to drive, which suggests that the warning advice may not be having the desired impact. The findings of this research have implications for current countermeasures in this area. These have included enhancing the role that prescribing doctors have in providing warnings and advice to patients about the impact that their medication can have on driving, increasing consumer perceptions of the authority of pharmacists on this issue, and the reinforcement of the warning message. More broadly, it is suggested that there would be benefit in a wider dissemination of research-based information on increased crash risk and systematic monitoring and publicity about the representation of medications in crashes resulting in injuries and fatalities. Suggestions for future research concern the continued investigation of the effects of medications and interactions with existing medical conditions and other substances on driving skills, effects of variations in warning label design, individual behaviours and characteristics (particularly among those groups who are dependent upon prescription medication) and validation of consumer self-assessment of impairment.

Wayfinding : a simple concept, a complex process

Wayfinding is the process of finding your way to a destination in a familiar or unfamiliar setting using any cues given by the environment. Due to its ubiquity in everyday life, wayfinding appears on the surface to be a simply characterised and understood process, however this very ubiquity and the resulting need to refine and optimise wayfinding has lead to a great number of studies that have revealed that it is in fact a deeply complex exercise. In this paper we examine the motivations for investigating wayfinding, with particular attention being paid to the unique challenges faced in transportation hubs, and discuss the associated principles and factors involved as they have been perceived from different research perspectives.We also review the approaches used to date in the modelling of wayfinding in various contexts. We attempt to draw together the different perspectives applied to wayfinding and postulate the importance of wayfinding and the need to understand this seemingly simple, but concurrently complex, process.

Reaching high-risk adolescents : a process evaluation of a school based injury prevention program

High-risk adolescents are a population most vulnerable to harm from injury due to increased engagement in risk taking behaviour. There is a gap in the literature regarding how universal school based injury prevention programs apply to high-risk adolescents. This study involves a component of the process evaluation of a school based injury prevention program, as it relates to high-risk adolescents (13-14 years)...

Editorial : Learning, teaching and disseminating knowledge in business process management

Process-oriented thinking has become the major paradigm for managing companies and other organizations. The push for better processes has been even more intense due to rapidly evolving client needs, borderless global markets and innovations swiftly penetrating the market. Thus, education is decisive for successfully introducing and implementing Business Process Management (BPM) initiatives. However, BPM education has been an area of challenge. This special issue aims to provide current research on various aspects of BPM education. It is an initial effort for consolidating better practices, experiences and pedagogical outcomes founded with empirical evidence to contribute towards the three pillars of education: learning, teaching, and disseminating knowledge in BPM.

Assessment of real-time networks and timing for process bus applications

Widespread adoption by electricity utilities of Non-Conventional Instrument Transformers, such as optical or capacitive transducers, has been limited due to the lack of a standardised interface and multi-vendor interoperability. Low power analogue interfaces are being replaced by IEC 61850 9 2 and IEC 61869 9 digital interfaces that use Ethernet networks for communication. These ‘process bus’ connections achieve significant cost savings by simplifying connections between switchyard and control rooms; however the in-service performance when these standards are employed is largely unknown. The performance of real-time Ethernet networks and time synchronisation was assessed using a scale model of a substation automation system. The test bed was constructed from commercially available timing and protection equipment supplied by a range of vendors. Test protocols have been developed to thoroughly evaluate the performance of Ethernet networks and network based time synchronisation. The suitability of IEEE Std 1588 Precision Time Protocol (PTP) as a synchronising system for sampled values was tested in the steady state and under transient conditions. Similarly, the performance of hardened Ethernet switches designed for substation use was assessed under a range of network operating conditions. This paper presents test methods that use a precision Ethernet capture card to accurately measure PTP and network performance. These methods can be used for product selection and to assess ongoing system performance as substations age. Key findings on the behaviour of multi-function process bus networks are presented. System level tests were performed using a Real Time Digital Simulator and transformer protection relay with sampled value and Generic Object Oriented Substation Events (GOOSE) capability. These include the interactions between sampled values, PTP and GOOSE messages. Our research has demonstrated that several protocols can be used on a shared process bus, even with very high network loads. This should provide confidence that this technology is suitable for transmission substations.

Optimisation of bio-oil extraction process from Beauty Leaf (Calophyllum inophyllum) oil seed as a second generation biodiesel source

The Beauty Leaf tree (Calophyllum inophyllum) is a potential source of non-edible vegetable oil for producing future generation biodiesel because of its ability to grow in a wide range of climate conditions, easy cultivation, high fruit production rate, and the high oil content in the seed. This plant naturally occurs in the coastal areas of Queensland and the Northern Territory in Australia, and is also widespread in south-east Asia, India and Sri Lanka. Although Beauty Leaf is traditionally used as a source of timber and orientation plant, its potential as a source of second generation biodiesel is yet to be exploited. In this study, the extraction process from the Beauty Leaf oil seed has been optimised in terms of seed preparation, moisture content and oil extraction methods. The two methods that have been considered to extract oil from the seed kernel are mechanical oil extraction using an electric powered screw press, and chemical oil extraction using n-hexane as an oil solvent. The study found that seed preparation has a significant impact on oil yields, especially in the screw press extraction method. Kernels prepared to 15% moisture content provided the highest oil yields for both extraction methods. Mechanical extraction using the screw press can produce oil from correctly prepared product at a low cost, however overall this method is ineffective with relatively low oil yields. Chemical extraction was found to be a very effective method for oil extraction for its consistence performance and high oil yield, but cost of production was relatively higher due to the high cost of solvent. However, a solvent recycle system can be implemented to reduce the production cost of Beauty Leaf biodiesel. The findings of this study are expected to serve as the basis from which industrial scale biodiesel production from Beauty Leaf can be made.

Empirical investigation of the usefulness of Gateway constructs in process models

Process modeling grammars are used to create scripts of a business domain that a process-aware information system is intended to support. A key grammatical construct of such grammars is known as a Gateway. A Gateway construct is used to describe scenarios in which the workflow of a process diverges or converges according to relevant conditions. Gateway constructs have been subjected to much academic discussion about their meaning, role and usefulness, and have been linked to both process-modeling errors and process-model understandability. This paper examines perceptual discriminability effects of Gateway constructs on an individual's abilities to interpret process models. We compare two ways of expressing two convergence and divergence patterns – Parallel Split and Simple Merge – implemented in a process modeling grammar. On the basis of an experiment with 98 students, we provide empirical evidence that Gateway constructs aid the interpretation of process models due to a perceptual discriminability effect, especially when models are complex. We discuss the emerging implications for research and practice, in terms of revisions to grammar specifications, guideline development and design choices in process modeling.

The use of an electrostatic lens to enhance the efficiency of the electrospinning process

Electrospun scaffolds manufactured using conventional electrospinning configurations have an intrinsic thickness limitation, due to a charge build-up at the collector. To overcome this limitation, an electrostatic lens has been developed that, at the same relative rate of deposition, focuses the polymer jet onto a smaller area of the collector, resulting in the fabrication of thick scaffolds within a shorter period of time. We also observed that a longer deposition time (up to 13 h, without the intervention of the operator) could be achieved when the electrostatic lens was utilised, compared to 9–10 h with a conventional processing set-up and also showed that fibre fusion was less likely to occur in the modified method. This had a significant impact on the mechanical properties, as the scaffolds obtained with the conventional process had a higher elastic modulus and ultimate stress and strain at short times. However, as the thickness of the scaffolds produced by the conventional electrospinning process increased, a 3-fold decrease in the mechanical properties was observed. This was in contrast to the modified method, which showed a continual increase in mechanical properties, with the properties of the scaffold finally having similar mechanical properties to the scaffolds obtained via the conventional process at longer times. This “focusing” device thus enabled the fabrication of thicker 3-dimensional electrospun scaffolds (of thicknesses up to 3.5 mm), representing an important step towards the production of scaffolds for tissue engineering large defect sites in a multitude of tissues.

Does Venture Opportunity Variation Matter? Investigating Systematic Process Differences Between Innovative and Imitative New Ventures

The central thesis in the article is that the venture creation process is different for innovative versus imitative ventures. This holds up; the pace of the process differs by type of venture as do, in line with theory-based hypotheses, the effects of certain human capital (HC) and social capital (SC) predictors. Importantly, and somewhat unexpectedly, the theoretically derived models using HC, SC, and certain controls are relatively successful explaining progress in the creation process for the minority of innovative ventures, but achieve very limited success for the imitative majority. This may be due to a rationalistic bias in conventional theorizing and suggests that there is need for considerable theoretical development regarding the important phenomenon of new venture creation processes. Another important result is that the building up of instrumental social capital, which we assess comprehensively and as a time variant construct, is important for making progress with both types of ventures, and increasingly, so as the process progresses. This result corroborates with stronger operationalization and more appropriate analysis method what previously published research has only been able to hint at.