974 resultados para Direct method
Resumo:
CHAPTER 1:FLUID-VISCOUS DAMPERS In this chapter the fluid-viscous dampers are introduced. The first section is focused on the technical characteristics of these devices, their mechanical behavior and the latest evolution of the technology whose they are equipped. In the second section we report the definitions and the guide lines about the design of these devices included in some international codes. In the third section the results of some experimental tests carried out by some authors on the response of these devices to external forces are discussed. On this purpose we report some technical schedules that are usually enclosed to the devices now available on the international market. In the third section we show also some analytic models proposed by various authors, which are able to describe efficiently the physical behavior of the fluid-viscous dampers. In the last section we propose some cases of application of these devices on existing structures and on new-construction structures. We show also some cases in which these devices have been revealed good for aims that lies outside the reduction of seismic actions on the structures. CHAPTER 2:DESIGN METHODS PROPOSED IN LITERATURE In this chapter the more widespread design methods proposed in literature for structures equipped by fluid-viscous dampers are introduced. In the first part the response of sdf systems in the case of harmonic external force is studied, in the last part the response in the case of random external force is discussed. In the first section the equations of motion in the case of an elastic-linear sdf system equipped with a non-linear fluid-viscous damper undergoing a harmonic force are introduced. This differential problem is analytically quite complex and it’s not possible to be solved in a closed form. Therefore some authors have proposed approximate solution methods. The more widespread methods are based on equivalence principles between a non-linear device and an equivalent linear one. Operating in this way it is possible to define an equivalent damping ratio and the problem becomes linear; the solution of the equivalent problem is well-known. In the following section two techniques of linearization, proposed by some authors in literature, are described: the first technique is based on the equivalence of the energy dissipated by the two devices and the second one is based on the equivalence of power consumption. After that we compare these two techniques by studying the response of a sdf system undergoing a harmonic force. By introducing the equivalent damping ratio we can write the equation of motion of the non-linear differential problem in an implicit form, by dividing, as usual, for the mass of the system. In this way, we get a reduction of the number of variables, by introducing the natural frequency of the system. The equation of motion written in this form has two important properties: the response is linear dependent on the amplitude of the external force and the response is dependent on the ratio of the frequency of the external harmonic force and the natural frequency of the system only, and not on their single values. All these considerations, in the last section, are extended to the case of a random external force. CHAPTER 3: DESIGN METHOD PROPOSED In this chapter the theoretical basis of the design method proposed are introduced. The need to propose a new design method for structures equipped with fluid-viscous dampers arises from the observation that the methods reported in literature are always iterative, because the response affects some parameters included in the equation of motion (such as the equivalent damping ratio). In the first section the dimensionless parameterε is introduced. This parameter has been obtained from the definition of equivalent damping ratio. The implicit form of the equation of motion is written by introducing the parameter ε, instead of the equivalent damping ratio. This new implicit equation of motions has not any terms affected by the response, so that once ε is known the response can be evaluated directly. In the second section it is discussed how the parameter ε affects some characteristics of the response: drift, velocity and base shear. All the results described till this point have been obtained by keeping the non-linearity of the behavior of the dampers. In order to get a linear formulation of the problem, that is possible to solve by using the well-known methods of the dynamics of structures, as we did before for the iterative methods by introducing the equivalent damping ratio, it is shown how the equivalent damping ratio can be evaluated from knowing the value of ε. Operating in this way, once the parameter ε is known, it is quite easy to estimate the equivalent damping ratio and to proceed with a classic linear analysis. In the last section it is shown how the parameter ε could be taken as reference for the evaluation of the convenience of using non-linear dampers instead of linear ones on the basis of the type of external force and the characteristics of the system. CHAPTER 4: MULTI-DEGREE OF FREEDOM SYSTEMS In this chapter the design methods of a elastic-linear mdf system equipped with non-linear fluidviscous dampers are introduced. It has already been shown that, in the sdf systems, the response of the structure can be evaluated through the estimation of the equivalent damping ratio (ξsd) assuming the behavior of the structure elastic-linear. We would to mention that some adjusting coefficients, to be applied to the equivalent damping ratio in order to consider the actual behavior of the structure (that is non-linear), have already been proposed in literature; such coefficients are usually expressed in terms of ductility, but their treatment is over the aims of this thesis and we does not go into further. The method usually proposed in literature is based on energy equivalence: even though this procedure has solid theoretical basis, it must necessary include some iterative process, because the expression of the equivalent damping ratio contains a term of the response. This procedure has been introduced primarily by Ramirez, Constantinou et al. in 2000. This procedure is reported in the first section and it is defined “Iterative Method”. Following the guide lines about sdf systems reported in the previous chapters, it is introduced a procedure for the assessment of the parameter ε in the case of mdf systems. Operating in this way the evaluation of the equivalent damping ratio (ξsd) can be done directly without implementing iterative processes. This procedure is defined “Direct Method” and it is reported in the second section. In the third section the two methods are analyzed by studying 4 cases of two moment-resisting steel frames undergoing real accelerogramms: the response of the system calculated by using the two methods is compared with the numerical response obtained from the software called SAP2000-NL, CSI product. In the last section a procedure to create spectra of the equivalent damping ratio, affected by the parameter ε and the natural period of the system for a fixed value of exponent α, starting from the elasticresponse spectra provided by any international code, is introduced.
Resumo:
The hierarchical organisation of biological systems plays a crucial role in the pattern formation of gene expression resulting from the morphogenetic processes, where autonomous internal dynamics of cells, as well as cell-to-cell interactions through membranes, are responsible for the emergent peculiar structures of the individual phenotype. Being able to reproduce the systems dynamics at different levels of such a hierarchy might be very useful for studying such a complex phenomenon of self-organisation. The idea is to model the phenomenon in terms of a large and dynamic network of compartments, where the interplay between inter-compartment and intra-compartment events determines the emergent behaviour resulting in the formation of spatial patterns. According to these premises the thesis proposes a review of the different approaches already developed in modelling developmental biology problems, as well as the main models and infrastructures available in literature for modelling biological systems, analysing their capabilities in tackling multi-compartment / multi-level models. The thesis then introduces a practical framework, MS-BioNET, for modelling and simulating these scenarios exploiting the potential of multi-level dynamics. This is based on (i) a computational model featuring networks of compartments and an enhanced model of chemical reaction addressing molecule transfer, (ii) a logic-oriented language to flexibly specify complex simulation scenarios, and (iii) a simulation engine based on the many-species/many-channels optimised version of Gillespie’s direct method. The thesis finally proposes the adoption of the agent-based model as an approach capable of capture multi-level dynamics. To overcome the problem of parameter tuning in the model, the simulators are supplied with a module for parameter optimisation. The task is defined as an optimisation problem over the parameter space in which the objective function to be minimised is the distance between the output of the simulator and a target one. The problem is tackled with a metaheuristic algorithm. As an example of application of the MS-BioNET framework and of the agent-based model, a model of the first stages of Drosophila Melanogaster development is realised. The model goal is to generate the early spatial pattern of gap gene expression. The correctness of the models is shown comparing the simulation results with real data of gene expression with spatial and temporal resolution, acquired in free on-line sources.
Resumo:
1.Ricostruzione mandibolare La ricostruzione mandibolare è comunemente eseguita utilizzando un lembo libero perone. Il metodo convenzionale (indiretto) di Computer Aided Design e Computer Aided Manifacturing prevede il modellamento manuale preoperatorio di una placca di osteosintesi standard su un modello stereolitografico della mandibola. Un metodo innovativo CAD CAM diretto comprende 3 fasi: 1) pianificazione virtuale 2) computer aided design della dima di taglio mandibolari, della dima di taglio del perone e della placca di osteosintesi e 3) Computer Aided Manufacturing dei 3 dispositivi chirurgici personalizzati. 7 ricostruzioni mandibolari sono state effettuate con il metodo diretto. I risultati raggiunti e le modalità di pianificazione sono descritte e discusse. La progettazione assistita da computer e la tecnica di fabbricazione assistita da computer facilita un'accurata ricostruzione mandibolare ed apporta un miglioramento statisticamente significativo rispetto al metodo convenzionale. 2. Cavità orale e orofaringe Un metodo ricostruttivo standard per la cavità orale e l'orofaringe viene descritto. 163 pazienti affetti da cancro della cavità orale e dell'orofaringe, sono stati trattati dal 1992 al 2012 eseguendo un totale di 175 lembi liberi. La strategia chirurgica è descritta in termini di scelta del lembo, modellamento ed insetting. I modelli bidimensionali sono utilizzati per pianificare una ricostruzione tridimensionale con il miglior risultato funzionale ed estetico. I modelli, la scelta del lembo e l' insetting sono descritti per ogni regione. Complicazioni e risultati funzionali sono stati valutati sistematicamente. I risultati hanno mostrato un buon recupero funzionale con le tecniche ricostruttive descritte. Viene proposto un algoritmo ricostruttivo basato su template standard.
Resumo:
Conjugated polymers and conjugated polymer blends have attracted great interest due to their potential applications in biosensors and organic electronics. The sub-100 nm morphology of these materials is known to heavily influence their electromechanical properties and the performance of devices they are part of. Electromechanical properties include charge injection, transport, recombination, and trapping, the phase behavior and the mechanical robustness of polymers and blends. Electrical scanning probe microscopy techniques are ideal tools to measure simultaneously electric (conductivity and surface potential) and dielectric (dielectric constant) properties, surface morphology, and mechanical properties of thin films of conjugated polymers and their blends.rnIn this thesis, I first present a combined topography, Kelvin probe force microscopy (KPFM), and scanning conductive torsion mode microscopy (SCTMM) study on a gold/polystyrene model system. This system is a mimic for conjugated polymer blends where conductive domains (gold nanoparticles) are embedded in a non-conductive matrix (polystyrene film), like for polypyrrole:polystyrene sulfonate (PPy:PSS), and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). I controlled the nanoscale morphology of the model by varying the distribution of gold nanoparticles in the polystyrene films. I studied the influence of different morphologies on the surface potential measured by KPFM and on the conductivity measured by SCTMM. By the knowledge I gained from analyzing the data of the model system I was able to predict the nanostructure of a homemade PPy:PSS blend.rnThe morphologic, electric, and dielectric properties of water based conjugated polymer blends, e.g. PPy:PSS or PEDOT:PSS, are known to be influenced by their water content. These properties also influence the macroscopic performance when the polymer blends are employed in a device. In the second part I therefore present an in situ humidity-dependence study on PPy:PSS films spin-coated and drop-coated on hydrophobic highly ordered pyrolytic graphite substrates by KPFM. I additionally used a particular KPFM mode that detects the second harmonic electrostatic force. With this, I obtained images of dielectric constants of samples. Upon increasing relative humidity, the surface morphology and composition of the films changed. I also observed that relative humidity affected thermally unannealed and annealed PPy:PSS films differently. rnThe conductivity of a conjugated polymer may change once it is embedded in a non-conductive matrix, like for PPy embedded in PSS. To measure the conductivity of single conjugated polymer particles, in the third part, I present a direct method based on microscopic four-point probes. I started with metal core-shell and metal bulk particles as models, and measured their conductivities. The study could be extended to measure conductivity of single PPy particles (core-shell and bulk) with a diameter of a few micrometers.
Resumo:
The glucose transporter IICB of the Escherichia coli phosphotransferase system (PTS) consists of a polytopic membrane domain (IIC) responsible for substrate transport and a hydrophilic C-terminal domain (IIB) responsible for substrate phosphorylation. We have overexpressed and purified a triple mutant of IIC (mut-IIC), which had recently been shown to be suitable for crystallization purposes. Mut-IIC was homodimeric as determined by blue native-PAGE and gel-filtration, and had an eyeglasses-like structure as shown by negative-stain transmission electron microscopy (TEM) and single particle analysis. Glucose binding and transport by mut-IIC, mut-IICB and wildtype-IICB were compared with scintillation proximity and in vivo transport assays. Binding was reduced and transport was impaired by the triple mutation. The scintillation proximity assay allowed determination of substrate binding, affinity and specificity of wildtype-IICB by a direct method. 2D crystallization of mut-IIC yielded highly-ordered tubular crystals and made possible the calculation of a projection structure at 12Å resolution by negative-stain TEM. Immunogold labeling TEM revealed the sidedness of the tubular crystals, and high-resolution atomic force microscopy the surface structure of mut-IIC. This work presents the structure of a glucose PTS transporter at the highest resolution achieved so far and sets the basis for future structural studies.
Resumo:
Structural analyses of heterologously expressed mammalian membrane proteins remain a great challenge given that microgram to milligram amounts of correctly folded and highly purified proteins are required. Here, we present a novel method for the expression and affinity purification of recombinant mammalian and in particular human transport proteins in Xenopus laevis frog oocytes. The method was validated for four human and one murine transporter. Negative stain transmission electron microscopy (TEM) and single particle analysis (SPA) of two of these transporters, i.e., the potassium-chloride cotransporter 4 (KCC4) and the aquaporin-1 (AQP1) water channel, revealed the expected quaternary structures within homogeneous preparations, and thus correct protein folding and assembly. This is the first time a cation-chloride cotransporter (SLC12) family member is isolated, and its shape, dimensions, low-resolution structure and oligomeric state determined by TEM, i.e., by a direct method. Finally, we were able to grow 2D crystals of human AQP1. The ability of AQP1 to crystallize was a strong indicator for the structural integrity of the purified recombinant protein. This approach will open the way for the structure determination of many human membrane transporters taking full advantage of the Xenopus laevis oocyte expression system that generally yields robust functional expression.
Resumo:
Noise and vibration has long been sought to be reduced in major industries: automotive, aerospace and marine to name a few. Products must be tested and pass certain levels of federally regulated standards before entering the market. Vibration measurements are commonly acquired using accelerometers; however limitations of this method create a need for alternative solutions. Two methods for non-contact vibration measurements are compared: Laser Vibrometry, which directly measures the surface velocity of the aluminum plate, and Nearfield Acoustic Holography (NAH), which measures sound pressure in the nearfield, and using Green’s Functions, reconstructs the surface velocity at the plate. The surface velocity from each method is then used in modal analysis to determine the comparability of frequency, damping and mode shapes. Frequency and mode shapes are also compared to an FEA model. Laser Vibrometry is a proven, direct method for determining surface velocity and subsequently calculating modal analysis results. NAH is an effective method in locating noise sources, especially those that are not well separated spatially. Little work has been done in incorporating NAH into modal analysis.
Resumo:
Electrical Power Assisted Steering system (EPAS) will likely be used on future automotive power steering systems. The sinusoidal brushless DC (BLDC) motor has been identified as one of the most suitable actuators for the EPAS application. Motor characteristic variations, which can be indicated by variations of the motor parameters such as the coil resistance and the torque constant, directly impart inaccuracies in the control scheme based on the nominal values of parameters and thus the whole system performance suffers. The motor controller must address the time-varying motor characteristics problem and maintain the performance in its long service life. In this dissertation, four adaptive control algorithms for brushless DC (BLDC) motors are explored. The first algorithm engages a simplified inverse dq-coordinate dynamics controller and solves for the parameter errors with the q-axis current (iq) feedback from several past sampling steps. The controller parameter values are updated by slow integration of the parameter errors. Improvement such as dynamic approximation, speed approximation and Gram-Schmidt orthonormalization are discussed for better estimation performance. The second algorithm is proposed to use both the d-axis current (id) and the q-axis current (iq) feedback for parameter estimation since id always accompanies iq. Stochastic conditions for unbiased estimation are shown through Monte Carlo simulations. Study of the first two adaptive algorithms indicates that the parameter estimation performance can be achieved by using more history data. The Extended Kalman Filter (EKF), a representative recursive estimation algorithm, is then investigated for the BLDC motor application. Simulation results validated the superior estimation performance with the EKF. However, the computation complexity and stability may be barriers for practical implementation of the EKF. The fourth algorithm is a model reference adaptive control (MRAC) that utilizes the desired motor characteristics as a reference model. Its stability is guaranteed by Lyapunov’s direct method. Simulation shows superior performance in terms of the convergence speed and current tracking. These algorithms are compared in closed loop simulation with an EPAS model and a motor speed control application. The MRAC is identified as the most promising candidate controller because of its combination of superior performance and low computational complexity. A BLDC motor controller developed with the dq-coordinate model cannot be implemented without several supplemental functions such as the coordinate transformation and a DC-to-AC current encoding scheme. A quasi-physical BLDC motor model is developed to study the practical implementation issues of the dq-coordinate control strategy, such as the initialization and rotor angle transducer resolution. This model can also be beneficial during first stage development in automotive BLDC motor applications.
Resumo:
We investigate a class of optimal control problems that exhibit constant exogenously given delays in the control in the equation of motion of the differential states. Therefore, we formulate an exemplary optimal control problem with one stock and one control variable and review some analytic properties of an optimal solution. However, analytical considerations are quite limited in case of delayed optimal control problems. In order to overcome these limits, we reformulate the problem and apply direct numerical methods to calculate approximate solutions that give a better understanding of this class of optimization problems. In particular, we present two possibilities to reformulate the delayed optimal control problem into an instantaneous optimal control problem and show how these can be solved numerically with a stateof- the-art direct method by applying Bock’s direct multiple shooting algorithm. We further demonstrate the strength of our approach by two economic examples.
Resumo:
The most direct method of investigating past variations of the atmospheric CO2 concentration before 1958, when continuous direct atmospheric CO2 measurements started, is the analysis of air extracted from suitable ice cores. Here we present a new detailed CO2 record from the Dronning Maud Land (DML) ice core, drilled in the framework of the European Project for Ice Coring in Antarctica (EPICA) and some new measurements on a previously drilled ice core from the South Pole. The DML CO2 record shows an increase from about 278 to 282 parts per million by volume (ppmv) between ad 1000 and ad 1200 and a fairly continuous decrease to a mean value of about 277 ppmv around ad 1700. While the new South Pole measurements agree well with DML at the minimum at ad 1700 they are on average about 2 ppmv lower during the period ad 1000-1500. Published measurements from the coastal high-accumulation site Law Dome are considered as very reliable because of the reproducibility of the measurements, high temporal resolution and an accurate time scale. Other Antarctic ice cores could not, or only partly, reproduce the pre-industrial measurements from Law Dome. A comparison of the trends of DML and Law Dome shows a general agreement. However we should be able to rule out co-variations caused by the same artefact. Two possible effects are discussed, first production of CO2 by chemical reactions and second diffusion of dissolved air through the ice matrix into the bubbles. While the first effect cannot be totally excluded, comparison of the Law Dome and DML record shows that dissolved air diffusing to bubbles cannot be responsible for the pre-industrial variation. Therefore, the new record is not a proof of the Law Dome results but the first very strong support from an ice core of the Antarctic plateau.
Resumo:
La nueva legislación en materia fitosanitaria se dirige hacia una Gestión Integrada de Plagas (GIP). Estos programas dan preferencia a aquellos métodos más respetuosos y sostenibles con el medio ambiente, siendo piezas claves en ellos el control biológico, el físico y otros de carácter no químico. Sin embargo, el uso de insecticidas selectivos es a veces necesario para el adecuado manejo de plagas en cultivos hortícolas. Por ello, el objetivo general de este estudio es aportar conocimientos para mejorar el control de plagas en cultivos hortícolas, mediante la integración de tres estrategias de lucha: biológica, física y química. Una parte de este trabajo ha consistido en el estudio de los posibles efectos que mallas tratadas con insecticida (bifentrin) pudieran provocar mediante diferentes ensayos de laboratorio, invernadero y campo, en los enemigos naturales Orius laevigatus (Fieber) (Hemiptera: Anthocoridae) (depredador de trips), Nesidiocoris tenuis (Reuter) (Hemiptera: Miridae) (depredador de mosca blanca y Tuta absoluta (Meirick) (Lepidoptera: Gelechiidae)), y otros agentes de biocontrol comúnmente usados en cultivos hortícolas protegidos. Este tipo de mallas se han empleado con éxito en entomología médica para controlar mosquitos vectores de la malaria, y actualmente se está trabajando en su desarrollo para uso agrícola como método de exclusión, y método directo de control de plagas. En los ensayos realizados en laboratorio, O. laevigatus y N. tenuis no fueron capaces de detectar la presencia de bifentrin en el ensayo de preferencia. Además, no se produjo mortalidad a corto plazo (72 horas) en ambos chinches depredadores. Por el contrario, se registró una elevada mortalidad cuando se expusieron por contacto a la malla tratada durante 72 horas en cajas de dimensiones reducidas (10 cm de diámetro X 3 cm de altura). En ensayos llevados a cabo bajo condiciones más reales de exposición, en un invernadero experimental con jaulas de 25 X 25 X 60 cm de altura, no se produjo ningún efecto en la mortalidad a corto plazo (72 horas) o en los parámetros reproductivos de O. laevigatus y N. tenuis. Finalmente, en ensayos de campo realizados en túneles semi-comerciales (8 m de largo X 6,5 m de ancho X 2,6 m de altura), ni las condiciones ambientales [temperatura, humedad relativa, radiación ultravioleta (UV) y fotosintéticamente activa (PAR)], ni los enemigos naturales, se vieron afectados por la presencia de la malla tratada con bifentrin en el cultivo. Sin embargo, los resultados no fueron concluyentes, debido al bajo establecimiento de los agentes de biocontrol liberados. Por lo tanto, más estudios son necesarios en invernaderos comerciales para confirmar los resultados preliminares de compatibilidad. Además, en este trabajo se han evaluado los efectos letales (mortalidad) y subletales (parámetros reproductivos) de seis modernos insecticidas sobre los chinches depredadores O. laevigatus y N. tenuis, mediante ensayos de laboratorio y persistencia. Los ensayos se realizaron por contacto residual, aplicando los insecticidas a la dosis máxima de campo sobre placas de cristal (laboratorio) o plantas (persistencia). Los productos fitosanitarios se seleccionaron por representar a un grupo de modernos plaguicidas con modos de acción en principio más selectivos para los enemigos naturales que antiguos plaguicidas como organoclorados, oroganofosforados o carbamatos, y por su uso frecuente en cultivos hortícolas donde O. laevigatus y N. tenuis están presentes. Todos ellos están incluidos o en proceso de inclusión en la lista comunitaria de sustancias activas para uso agrícola, Anexo I de la Directiva 91/414/CEE: abamectina y emamectina (avermectinas neurotóxicas, activadoras del canal del cloro), deltametrina (piretroide neurotóxico, modulador del canal del sodio, control positivo), flubendiamida (neurotóxico, modulador del receptor de rianodina), spinosad (naturalito neurotóxico, agonistas/antagonistas del receptor de nicotínico acetilcolina) y spiromesifen (inhibidor de la acetil CoA carboxilasa). El estudio mostró que O. laevigatus fue más susceptible a los insecticidas que N. tenuis. Además, los resultados revelaron que flubendiamida y spiromesifen fueron compatibles con los dos enemigos naturales estudiados, y por tanto se podrían usar en programas de GIP. Por el contrario, los insecticidas abamectina, deltametrina, emamectina y spinosad no fueron selectivos para ninguno de los chinches depredadores. Sin embargo, los estudios de persistencia demostraron que a pesar de que estos insecticidas no proporcionaron selectividad fisiológica, pueden proporcionar selectividad ecológica en algunos casos. Abamectina, deltametrina, emamectina y spinosad podrían ser compatibles con N. tenuis si el enemigo natural es introducido en el cultivo 4 días después de su aplicación. En el caso de O. laevigatus, abamectina, deltametrina y spinosad se clasificaron como persistentes, por lo tanto es necesario completar el estudio con experimentos de semi-campo y campo que determinen si es posible su uso conjunto en programas de GIP. Por otro lado, emamectina podría ser compatible con O. laevigatus si el enemigo natural es introducido en el cultivo 7 días después de su aplicación. Por último, se ha comprobado la selectividad de tres insecticidas aceleradores de la muda (MACs) (metoxifenocida, tebufenocida y RH-5849) sobre O. laevigatus y N. tenuis. Además de realizar estudios para evaluar la toxicidad en laboratorio de los insecticidas por contacto residual e ingestión (principal modo de acción de los MAC´s), se extrajo RNA de los insectos y con el cDNA obtenido se secuenció y clonó el dominio de unión al ligando (LBD) del receptor de ecdisona correspondiente a O. laevigatus (OlEcR-LBD) y N. tenuis (NtEcR-LBD). Posteriormente, se obtuvo la configuración en tres dimensiones del LBD y se estudió el acoplamiento de las moléculas de los tres insecticidas en la cavidad que forman las 12 α-hélices que constituyen el EcR-LBD. En el caso de N. tenuis se debe mencionar que no fue posible la obtención de la secuencia completa del LBD. Sin embargo, se obtuvo una secuencia parcial (hélice 6-hélice 11), que mostró una alta conservación de aminoácidos con respecto a la obtenida en O. laevigatus. Los ensayos de toxicidad mostraron que metoxifenocida, tebufenocida y RH-5849 no produjeron ningún efecto nocivo en ambos depredadores. Además, los estudios de modelado por homología y acoplamiento molecular llevados a cabo con O. laevigatus, también indicaron que los MACs no produjeron ningún efecto deletéreo en este enemigo natural. Por lo tanto, estos compuestos pueden ser aplicados de manera segura en programas de GIP en los cuales O. laevigatus y N. tenuis estén presentes. ABSTRACT The new pesticide legislation on pest control is aimed at integrated pest management (IPM). These programs are based on the most environmentally sustainable approaches, where biological, physical control and other non-chemical methods are the cornerstone. However, selective pesticides are often required for pest management on horticultural crops. Therefore, the main goal of this study is to provide knowledge to improve pest control on horticultural crops through the integration of three strategies: biological, physical and chemical. Firstly, the effects of insecticide treated nets (bifenthrin) were evaluated in different laboratory, greenhouse and field experiments on the natural enemies Orius laevigatus (Fieber) (Hemiptera: Anthocoridae) (predator of thrips), Nesidiocoris tenuis (Reuter) (Hemiptera: Miridae) (predator of whiteflies and Tuta absoluta (Meirick) (Lepidoptera: Gelechiidae)), and other biocontrol agents commonly used on protected horticultural crops. These types of nets have been successfully used in medical entomology to control mosquito malaria vectors, and work is currently being done on their use as exclusion barriers and as a direct method of pest control in agriculture. In experiments made under laboratory conditions, O. laevigatus and N. tenuis were not able to detect the presence of bifenthrin in a dual-choice test. Furthermore, no shortterm mortality (72 hours) was recorded on both predatory bugs. In contrast, a high mortality rate was found when they were exposed by contact to the bifenthrin-treated net for 72 hours in small cages (10 cm diameter X 3 cm high). In assays carried out under more realistic conditions of exposure, in an experimental greenhouse with cages of 25 X 25 X 60 cm high, short-term mortality (72 hours) and reproductive parameters were not affected. Lastly, in field experiments carried out in semi-commercial tunnels (8 m long X 6.5 m width X 2.6 m high), neither environmental conditions [temperature, relative humidity, ultraviolet (UV) and photosynthetically active radiation (PAR)] nor natural enemies were affected by the presence of the bifenthrin-treated net on the crop. However, results were not conclusive, mainly due to a low settlement of the released biocontrol agents, and further studies are needed in commercial greenhouses to confirm our preliminary results of compatibility. Secondly, the lethal (mortality) and sublethal effects (reproductive parameters) of six modern pesticides on the predatory bugs O. laevigatus and N. tenuis has been evaluated through laboratory and persistence experiments. Trials were carried out by residual contact, applying the insecticides to the maximum field recommended concentration on glass plates (laboratory) or plants (persistence). Insecticides were chosen as representatives of modern pesticides with a more selective mode of action on natural enemies than organochlorine, organophosphorus and carbamate insecticides. Moreover, they were also chosen because of their frequent use on horticultural crops where O. laevigatus and N. tenuis are present. All of them have been included or have been requested for inclusion in the community list of active substances on the agricultural market, Annex I of the European Directive 91/414/EEC: abamectin and emamectin (neurotoxic avermectins, chloride channel activators), deltamethrin (neutotoxic pyrethroid, sodium channel modulator, positive commercial standard), flubendiamide (neurotoxic, rianodine receptor modulator), spinosad (neurotoxic naturalyte, nicotinic acetylcholine receptor allosteric activator) and spiromesifen (inhibitors of acetyl CoA carboxylase). The study showed that O. laevigatus was more susceptible to all the studied pesticides than N. tenuis. In addition, the research results indicated no impact of flubendiamide and spiromesifen on the two natural enemies studied under laboratory conditions. Consequently, both pesticides are candidates to be included in IPM programmes where these biocontrol agents are present. On the other hand, abamectin, deltamethrin, emamectin and spinosad were not selective for both predatory bugs in laboratory experiments. However, persistence test demonstrated that in spite of the lack of physiological selectivity, these pesticides can provide ecological selectivity in some cases. Abamectin, deltamethrin, emamectin and spinosad could be compatible with N. tenuis if the mirid bug is released 4 days after the insecticide treatment on the crop. With regard to O. laevigatus, abamectin, deltamethrin and spinosad were classified as persistent in our assays, thus the study should be completed with semi-field and field experiments in order to ascertain their possible joint use in IPM programs. In contrast, emamectin could be compatible with O. laevigatus if the pirate bug is released 7 days after the insecticide treatment on the crop. Finally, the selectivity of three moulting accelerating compounds (MACs) (methoxyfenozide, tebufenozide and RH-5849) has also been evaluated on O. laevigatus and N. tenuis. In addition to laboratory experiments to evaluate the toxicity of the insecticides by residual contact and ingestion, molecular approaches were used as well. RNA of both insects was isolated, cDNA was subsequently synthesized and the complete sequence of the ligand binding domain (LBD) of the ecdysone receptor of O. laevigatus (OlEcR-LBD) and N. tenuis (NtEcR-LBD) were determined. Afterwards, the three dimensional structure of LBD was constructed. Finally, the docking of the insecticide molecules in the cavity delineated by the 12 α-helix that composed the EcRLBD was performed. In the case of N. tenuis, it should be noted that in spite of intensive efforts, we did not manage to complete the sequence for the LBD.However, a partial sequence of the LBD was obtained (helix 6-helix 11), and a strong conservation between the amino acids of N. tenuis and O. laevigatus was observed. Results showed no biological activity of methoxyfenozide, tebufenozide and RH-5849, on both predatory bugs. Moreover, modeling of the OlEcR-LBD and docking experiments also suggested that MACs were devoid of any deleterious effect on O. laevigatus. Therefore, our results indicate that these compounds could be safely applied in IPM programs in which O. laevigatus and N. tenuis are present.
Resumo:
In this chapter we will introduce the reader to the techniques of the Boundary Element Method applied to simple Laplacian problems. Most classical applications refer to electrostatic and magnetic fields, but the Laplacian operator also governs problems such as Saint-Venant torsion, irrotational flow, fluid flow through porous media and the added fluid mass in fluidstructure interaction problems. This short list, to which it would be possible to add many other physical problems governed by the same equation, is an indication of the importance of the numerical treatment of the Laplacian operator. Potential theory has pioneered the use of BEM since the papers of Jaswon and Hess. An interesting introduction to the topic is given by Cruse. In the last five years a renaissance of integral methods has been detected. This can be followed in the books by Jaswon and Symm and by Brebbia or Brebbia and Walker.In this chapter we shall maintain an elementary level and follow a classical scheme in order to make the content accessible to the reader who has just started to study the technique. The whole emphasis has been put on the socalled "direct" method because it is the one which appears to offer more advantages. In this section we recall the classical concepts of potential theory and establish the basic equations of the method. Later on we discuss the discretization philosophy, the implementation of different kinds of elements and the advantages of substructuring which is unavoidable when dealing with heterogeneous materials.
Resumo:
La observación de la Tierra es una herramienta de gran utilidad en la actualidad para el estudio de los fenómenos que se dan en la misma. La observación se puede realizar a distintas escalas y por distintos métodos dependiendo del propósito. El actual Trabajo Final de Grado persigue exponer la observación del territorio mediante técnicas de Teledetección, o Detección Remota, y su aplicación en la exploración de hidrocarburos. Desde la Segunda Guerra Mundial el capturar imágenes aéreas de regiones de la Tierra estaba restringido a usos cartográficos en el sentido estricto. Desde aquellos tiempos, hasta ahora, ha acontecido una serie de avances científicos que permiten deducir características intrínsecas de la Tierra mediante mecanismos complejos que no apreciamos a simple vista, pero que, están configurados mediante determinados parámetros geométricos y electrónicos, que permiten generar series temporales de fenómenos físicos que se dan en la Tierra. Hoy en día se puede afirmar que el aprovechamiento del espectro electromagnético está en un punto máximo. Se ha pasado del análisis de la región del espectro visible al análisis del espectro en su totalidad. Esto supone el desarrollo de nuevos algoritmos, técnicas y procesos para extraer la mayor cantidad de información acerca de la interacción de la materia con la radiación electromagnética. La información que generan los sistemas de captura va a servir para la aplicación directa e indirecta de métodos de prospección de hidrocarburos. Las técnicas utilizadas en detección por sensores remotos, aplicadas en campañas geofísicas, son utilizadas para minimizar costes y maximizar resultados en investigaciones de campo. La predicción de anomalías en la zona de estudio depende del analista, quien diseña, calcula y evalúa las variaciones de la energía electromagnética reflejada o emitida por la superficie terrestre. Para dicha predicción se revisarán distintos programas espaciales, se evaluará la bondad de registro y diferenciación espectral mediante el uso de distintas clasificaciones (supervisadas y no supervisadas). Por su influencia directa sobre las observaciones realizadas, se realiza un estudio de la corrección atmosférica; se programan distintos modelos de corrección atmosférica para imágenes multiespectrales y se evalúan los métodos de corrección atmosférica en datos hiperespectrales. Se obtendrá temperatura de la zona de interés utilizando los sensores TM-4, ASTER y OLI, así como un Modelo Digital del Terreno generado por el par estereoscópico capturado por el sensor ASTER. Una vez aplicados estos procedimientos se aplicarán los métodos directos e indirectos, para la localización de zonas probablemente afectadas por la influencia de hidrocarburos y localización directa de hidrocarburos mediante teledetección hiperespectral. Para el método indirecto se utilizan imágenes capturadas por los sensores ETM+ y ASTER. Para el método directo se usan las imágenes capturadas por el sensor Hyperion. ABSTRACT The observation of the Earth is a wonderful tool for studying the different kind of phenomena that occur on its surface. The observation could be done by different scales and by different techniques depending on the information of interest. This Graduate Thesis is intended to expose the territory observation by remote sensing acquiring data systems and the analysis that can be developed to get information of interest. Since Second World War taking aerials photographs of scene was restricted only to a cartographic sense. From these days to nowadays, it have been developed many scientific advances that make capable the interpretation of the surface behavior trough complex systems that are configure by specific geometric and electronic parameters that make possible acquiring time series of the phenomena that manifest on the earth’s surface. Today it is possible to affirm that the exploitation of the electromagnetic spectrum is on a maxim value. In the past, analysis of the electromagnetic spectrum was carry in a narrow part of it, today it is possible to study entire. This implicates the development of new algorithms, process and techniques for the extraction of information about the interaction of matter with electromagnetic radiation. The information that has been acquired by remote sensing sensors is going to be a helpful tool for the exploration of hydrocarbon through direct and vicarious methods. The techniques applied in remote sensing, especially in geophysical campaigns, are employed to minimize costs and maximize results of ground-based geologic investigations. Forecasting of anomalies in the region of interest depends directly on the expertise data analyst who designs, computes and evaluates variations in the electromagnetic energy reflected or emanated from the earth’s surface. For an optimal prediction a review of the capture system take place; assess of the goodness in data acquisition and spectral separability, is carried out by mean of supervised and unsupervised classifications. Due to the direct influence of the atmosphere in the register data, a study of the minimization of its influence has been done; a script has been programed for the atmospheric correction in multispectral data; also, a review of hyperspectral atmospheric correction is conducted. Temperature of the region of interest is computed using the images captured by TM-4, ASTER and OLI, in addition to a Digital Terrain Model generated by a pair of stereo images taken by ASTER sensor. Once these procedures have finished, direct and vicarious methods are applied in order to find altered zones influenced by hydrocarbons, as well as pinpoint directly hydrocarbon presence by mean of hyperspectral remote sensing. For this purpose ETM+ and ASTER sensors are used to apply the vicarious method and Hyperion images are used to apply the direct method.
Resumo:
(SPA) En este trabajo, se propone un nuevo índice basado en el método directo de Lyapunov para el diseño de un algoritmo de reprogramación en tiempo real para líneas de metro. En este estudio se utiliza una versión modificada de un modelo de espacio de estados en tiempo real discreto, que considera los efectos de saturación en la línea de metro. Una vez que el modelo de espacio de estados se ha obtenido, el método directo de Lyapunov se aplica con el fin de analizar la estabilidad del sistema de la línea de metro. Como resultado de este análisis no sólo se propone un nuevo índice de estabilidad, sino también la creación de tres zonas de estabilidad para indicar el estado actual del sistema. Finalmente, se presenta un nuevo algoritmo que permite la reprogramación del calendario de los trenes en tiempo real en presencia de perturbaciones medianas. (ENG) A new Lyapunov-based index for designing a rescheduling algorithm in real time for metro lines has been proposed in this paper. A modified real time discrete space state model which considers saturation effects in the metro line has been utilized in this study. Once the space state model has been obtained, the direct method of Lyapunov is applied in order to analyze the stability of the metro line system. As a result of this analysis not only a new stability index is proposed, but also the establishment of three stability zones to indicate the current state of the system. Finally, a new algorithm which allows the rescheduling of the timetable in the real time of the trains under presence of medium disturbances has been presented.
Resumo:
Studies of molecular structures at or near their equilibrium configurations have long provided information on their geometry in terms of bond distances and angles. Far-from-equilibrium structures are relatively unknown—especially for complex systems—and generally, neither their dynamics nor their average geometries can be extrapolated from equilibrium values. For such nonequilibrium structures, vibrational amplitudes and bond distances play a central role in phenomena such as energy redistribution and chemical reactivity. Ultrafast electron diffraction, which was developed to study transient molecular structures, provides a direct method for probing the nature of complex molecules far from equilibrium. Here we present our ultrafast electron diffraction observations of transient structures for two cyclic hydrocarbons. At high internal energies of ≈4 eV, these molecules display markedly different behavior. For 1,3,5-cycloheptatriene, excitation results in the formation of hot ground-state structures with bond distances similar to those of the initial structure, but with nearly three times the average vibrational amplitude. Energy is redistributed within 5 ps, but with a negative temperature characterizing the nonequilibrium population. In contrast, the ring-opening reaction of 1,3-cyclohexadiene is shown to result in hot structures with a C—C bond distance of over 1.7 Å, which is 0.2 Å away from any expected equilibrium value. Even up to 400 ps, energy remains trapped in large-amplitude motions comprised of torsion and asymmetric stretching. These studies promise a new direction for studying structural dynamics in nonequilibrium complex systems.