Dynamic wet etching of silicon through isopropanol alcohol evaporation

In this paper, Isopropanol (IPA) availability during the anisotropic etching of silicon in Potassium Hydroxide (KOH) solutions was investigated. Squares of 8 to 40 m were patterned to (100) oriented silicon wafers through DWL (Direct Writing Laser) photolithography. The wet etching process was performed inside an open HDPE (High Density Polyethylene) flask with ultrasonic agitation. IPA volume and evaporation was studied in a dynamic etching process, and subsequent influence on the silicon etching was inspected. For the tested conditions, evaporation rates for water vapor and IPA were determined as approximately 0.0417 mL/min and 0.175 mL/min, respectively. Results demonstrate that IPA availability, and not concentration, plays an important role in the definition of the final structure. Transversal SEM (Scanning Electron Microscopy) analysis demonstrates a correlation between microloading effects (as a consequence of structure spacing) and the angle formed towards the (100) plane.

Macroinvertebrates under stochastic hydrological disturbance in Cerrado streams of Central Brazil

In the Cerrado vegetation, where the seasonal is well defined, rainfall has an important role in controlling the flow of streams and consequently on the structure of macroinvertebrates community. Despite the effects of rainfall associated with seasonality are well studied, little is known about the effects of stochastic rains on the community. In the present study we evaluated the structure and faunal composition of four first-order streams in Central Brazil during the dry season in two years, with and without stochastic rains. Community sampling was done by colonization of boards of high density polyethylene (HDPE), removed after one month submerged in streams. Analysis of Variance (ANOVA) performed indicated no difference in rarefied richness between the two periods, different from numeric density of organisms that was higher in the period without disturbance; moreover, the Detrended Correspondence Analysis (DCA) revealed differences in faunal composition between the two periods. Our results indicate that stochastic rainfall is an important factor in structuring the macroinvertebrates community in studied region.

The Use of Passive Samplers to Reveal Industrial and Agricultural Pollution Trends in Swiss Rivers

This study shows the efficiency of passive sampling to reveal industrial and agricultural pollution trends. Two practical applications for nonpolar and polar contaminants are presented. Low-density polyethylene (LDPE) samplers were deployed for one year in the Venoge River (VD) to monitor indicator PCBs (iPCBs, IUPAC nos. 28, 52, 101, 138, 153 and 180). The results showed that the impact of PCB emissions into the river is higher in summer than in other seasons due to the low flow rate of the river during this period. P,olar organic chemical integrative samplers (POCIS) were deployed for 4 months in the Sion-Riddes canal (VS) to investigate herbicides (terbuthylazine, diuron and linuron). Desisopropylatrazine-d5 (DIA-d5) was tested as a performance reference compound (PRC) to estimate aqueous concentration. The results showed an increase of water contamination due to the studied agricultural area. The maximal contamination was observed in April and corresponds to the period of herbicide application on the crops.

Caution on the storage of waters and aqueous solutions in plastic containers for hydrogen and oxygen stable isotope analysis

RATIONALE The choice of containers for storage of aqueous samples between their collection, transport and water hydrogen (2H) and oxygen (18O) stable isotope analysis is a topic of concern for a wide range of fields in environmental, geological, biomedical, food, and forensic sciences. The transport and separation of water molecules during water vapor or liquid uptake by sorption or solution and the diffusive transport of water molecules through organic polymer material by permeation or pervaporation may entail an isotopic fractionation. An experiment was conducted to evaluate the extent of such fractionation. METHODS Sixteen bottle-like containers of eleven different organic polymers, including low and high density polyethylene (LDPE and HDPE), polypropylene (PP), polycarbonate (PC), polyethylene terephthalate (PET), and perfluoroalkoxy-Teflon (PFA), of different wall thickness and size were completely filled with the same mineral water and stored for 659?days under the same conditions of temperature and humidity. Particular care was exercised to keep the bottles tightly closed and prevent loss of water vapor through the seals. RESULTS Changes of up to +5 parts per thousand for d2H values and +2.0 parts per thousand for d18O values were measured for water after more than 1?year of storage within a plastic container, with the magnitude of change depending mainly on the type of organic polymer, wall thickness, and container size. The most important variations were measured for the PET and PC bottles. Waters stored in glass bottles with Polyseal (TM) cone-lined PP screw caps and thick-walled HDPE or PFA containers with linerless screw caps having an integrally molded inner sealing ring preserved their original d2H and d18O values. The carbon, hydrogen, and oxygen stable isotope compositions of the organic polymeric materials were also determined. CONCLUSIONS The results of this study clearly show that for precise and accurate measurements of the water stable isotope composition in aqueous solutions, rigorous sampling and storage procedures are needed both for laboratory standards and for unknown samples. Copyright (c) 2012 John Wiley & Sons, Ltd.

Investigation of Plastic Pipes for Highway Applications, HR-373A, Phase II, 1997

It is generally accepted that high density polyethylene pipe (HDPE) performs well under live loads with shallow cover, provided the backfill is well compacted. Although industry standards require carefully compacted backfill, poor inspection and/or faulty construction may result in soils that provide inadequate restraint at the springlines of the pipes thereby causing failure. The objectives of this study were: 1) to experimentally define a lower limit of compaction under which the pipes perform satisfactorily, 2) to quantify the increase in soil support as compaction effort increases, 3) to evaluate pipe response for loads applied near the ends of the buried pipes, 4) to determine minimum depths of cover for a variety of pipes and soil conditions by analytically expanding the experimental results through the use of the finite element program CANDE. The test procedures used here are conservative especially for low-density fills loaded to high contact stresses. The failures observed in these tests were the combined effect of soil bearing capacity at the soil surface and localized wall bending of the pipes. Under a pavement system, the pipes' performance would be expected to be considerably better. With those caveats, the following conclusions are drawn from this study. Glacial till compacted to 50% and 80% provides insufficient support; pipe failureoccurs at surface contact stresses lower than those induced by highway trucks. On the other hand, sand backfill compacted to more than 110 pcf (17.3 kN/m3) is satisfactory. The failure mode for all pipes with all backfills is localized wall bending. At moderate tire pressures, i.e. contact stresses, deflections are reduced significantly when backfill density is increased from about 50 pcf (7.9 kN/m^3) to 90 pcf (14.1 kN/m^3). Above that unit weight, little improvement in the soil-pipe system is observed. Although pipe stiffness may vary as much as 16%, analyses show that backfill density is more important than pipe stiffness in controlling both deflections at low pipe stresses and at the ultimate capacity of the soil-pipe system. The rate of increase in ultimate strength of the system increases nearly linearly with increasing backfill density. When loads equivalent to moderate tire pressures are applied near the ends of the pipes, pipe deflections are slighly higher than when loaded at the center. Except for low density glacial till, the deflections near the ends are not excessive and the pipes perform satisfactorily. For contact stresses near the upper limit of truck tire pressures and when loaded near the end, pipes fail with localized wall bending. For flowable fill backfill, the ultimate capacity of the pipes is nearly doubled and at the upper limit of highway truck tire pressures, deflections are negligible. All pipe specimens tested at ambient laboratory room temperatures satisfied AASHTO minimum pipe stiffness requirements at 5% deflection. However, nearly all specimens tested at elevated pipe surface temperatures, approximately 122°F (50°C), failed to meet these requirements. Some HDPE pipe installations may not meet AASHTO minimum pipe stiffness requirements when installed in the summer months (i.e. if pipe surface temperatures are allowed to attain temperatures similar to those tested here). Heating of any portion of the pipe circumference reduced the load carrying capacity of specimens. The minimum soil cover depths, determined from the CANOE analysis, are controlled by the 5% deflection criterion. The minimum soil cover height is 12 in. (305 mm). Pipes with the poor silt and clay backfills with less than 85% compaction require a minimum soil cover height of 24 in. (610 mm). For the sand at 80% compaction, the A36 HDPE pipe with the lowest moment of inertia requires a minimum of 24 in. (610 mm) soil cover. The C48 HDPE pipe with the largest moment of inertia and all other pipes require a 12 in. (305 mm) minimum soil cover.

Potassium permanganate effects in postharvest conservation of the papaya cultivar Sunrise Golden

The objective of this work was to evaluate the effects of KMnO4 on the extension of postharvest life of 'Sunrise Golden' papaya, stored under modified atmosphere and refrigeration. Fruit with up to 10% yellow peel were harvested in a commercial orchard in Linhares, state of Espírito Santo, Brazil. Sets of three fruit (unit mass of 289.9±18.5 g) were wrapped in low-density polyethylene films (28 ¼m thick) containing sachets of KMnO4 at 0, 0.5, 1, 1.5, and 2 g per bag. The bags were sealed and stored at 10.4±0.9°C and 90±5% relative humidity for 25 days. After this period, the fruit were removed from the bags and maintained at 21±0.8°C and 90±5% relative humidity until complete ripening. Four days after bag sealing, CO2 concentration stabilized in all treatments, and was higher in bags without KMnO4. In all treatments, fruit reached the climacteric respiratory peak on the third day after bag removal, coinciding with peel color index of 3.5. Increasing the KMnO4 dose reduced the losses in fruit fresh matter, consistency and pulp electrolyte leakage. Potassium permanganate was effective in maintaining the fruit at the pre-climacteric stage during the 25-day storage, and did not interfere with normal ripening after bag removal.

Effects of packaging and temperature on postharvest of atemoya

Effects of refrigerated storage and different packages on postharvest behaviour of fruits of atemoya (Annona cherimola x A. squamosa) cv. PR3 were investigated. Fruits were individually sealed in copolymer (PD-955) and low-density polyethylene (LDPE) bags and stored for 21 days at 15°C or 25°C. Then they were unwrapped and maintained at 25°C, for ripening. Weight loss and firmness of fruits were both affected by storage time, temperature and packaging. Weight loss in packaged atemoyas was lower than in the control, non-wrapped fruits. A non-trained panel scored the atemoyas for overall eating quality and appearance. Fruits sealed in LDPE did not ripen, probably due to an injurious atmosphere developed inside the package. Atemoyas packaged in PD-955 film had a shelf-life of 17 days against 13 days of the control ones, both stored at 15°C, an increase of 30% on shelf-life.

Modified atmosphere packaging extending the storage life of 'douradão' peach

'Douradão' peach is a perishable product and when cold stored is subject to chilling injury. The objective of the experiment was to evaluate the effect of modified atmosphere packaging (MAP) and cold storage on quality and storage life of these peaches. Fruits were packed in polypropylene (PP) trays and placed inside low density polyethylene (LDPE) bags (30, 50, 60, 75 μm thickness) with active modified atmosphere (10 kPa CO2 + 1.5kPa O2, balance N2). The control was made with peaches held in nonwrapped PP trays. Fruits were kept at 1 ± 1 °C and 90 ± 5% relative humidity (RH) for 28 days and CO2 and O2 within packages was monitored every two days. After 14, 21 and 28 days, samples were withdrawn from MAP and kept in air at 25 ± 1 °C and 90 ± 5% RH for ripening. On the day of removal from the cold storage and after 4 days, peaches were evaluated for weight loss, decay incidence, flesh firmness, woolliness incidence, soluble solids content (SSC), titratable acidity (TA) and juice content. The results showed that MAP had influence on reducing weight loss and prevented postharvest decay. MAP of 1-2 kPa O2 and 3-6 kPa CO2 at 1 °C (from 50 and 60 μm LDPE films) were effective for keeping good quality of 'Douradão' peaches during 28 days of storage, the ripe fruits showed reduced incidence of woolliness, adequate juiciness and flesh firmness. Packages of 30 and 75 μm LDPE films were ineffective for reducing woolliness during cold storage. MAP fruits showed lower SSC and no relevant effect on TA. Control fruits did not present marketable conditions after 14 days of cold storage.

Effects of modified atmosphere packaging on ripening of 'Douradão' peach related to pectolytic enzymes activities and chilling injury symptoms

The present study evaluated the effects of modified atmosphere packaging on inhibition of the development of chilling injury symptoms in 'Douradão' peach after cold storage and the possible involvement of cell wall enzymes. Fruits were harvested at the middle stadium of ripening, packed in polypropylene trays and placed inside low density polyethylene (LDPE) bags (30, 50, 60 and 75 µm of thickness) with active modified atmosphere (10 kPa CO2 + 1.5 kPa O2, balance N2). The following treatments were tested: Control: peaches held in nonwrapped trays; MA30: LDPE film - 30 µm; MA50: LDPE film - 50 µm; MA60: LDPE film - 60 µm and MA75: LDPE film - 75 µm. Fruits were kept at 1±1ºC and 90±5% relative humidity (RH) for 28 days. After 14, 21 and 28 days, samples were withdrawn from MAP and kept in air at 25±1ºC and 90±5% RH for ripening. On the day of removal and after 4 days, peaches were evaluated for woolliness incidence, pectolytic enzymes activities. The respiratory rate and ethylene synthesis were monitored during 6 days of ripening. The results showed that MA50 and MA60 treatments had positive effect on the inhibition of the development of woolly texture and reduced pectin methylesterase activity on the ripe fruits, keeping good quality of 'Douradão' peach during 28 days of cold storage. The treatments Control, MA30 and MA75 showed higher woolliness incidence and did not present marketable conditions after 14 days of cold storage.

Avaliação da fotodegradação de poliolefinas através de exposição natural e artificial

Samples of polypropylene (PP) and low-density polyethylene (LDPE) were submitted to ultraviolet radiation, in the natural environment and also in the laboratory. Chemical modifications were quantified by the carbonyl index (CI), mechanical properties and melt flow index. The degradation in the laboratory was comparatively faster than in the environment for both types of polymers. The accelerating factor was determined for the various properties investigated. This parameter, however, showed a large variation with the degradation criteria and the type of polymer. The existence of a "universal accelerating factor", therefore, was not observed in the current study.

Estudo da resposta termicamente estimulada do compósito LDPE/CB por meio da técnica de corrente de despolarização termicamente estimulada (TSDC)

The thermally stimulated depolarization current (TSDC) in a range of temperature from 84 to 373 K, has been applied to study the depolarization current of polyethylene and polyethylene composites in form of film and filled with commercial or oxidative surface treatment carbon black. The diagrams of TSDC obtained show that the composite in which the carbon black had received oxidative surface treatment reducing on an average depolarization current intensity in a magnitude order if compared to the composite with commercial carbon black. Therefore in the area between α and β transitions the difference is accentuated by reaching a peak 55 times in a temperature of 240 K. The difference in results is explained in terms of molecular interactions neighboring of carbon black particles.

Creating carbon footprint calculating tool for plastic packaging products

The environmental challenges of plastic packaging industry have increased remarkably along with climate change debate. The interest to study carbon footprints of packaging has increased in packaging industry to find out the real climate change impacts of packaging. In this thesis the greenhouse gas discharges of plastic packaging during their life cycle is examined. The carbon footprint is calculated for food packaging manufactured from plastic laminate. The structure of the laminate is low density polyethylene (PE-LD) and oriented polypropylene (OPP), which have been joined together with laminating adhesive. The purpose is to find out the possibilities to create a carbon footprint calculating tool for plastic packaging and its usability in a plastic packaging manufacturing company. As a carbon footprint calculating method PAS 2050 standard has been used. In the calculations direct and indirect greenhouse gas discharges as well as avoided discharges are considered. Avoided discharges are born for example in packaging waste utilization as energy. The results of the calculations have been used to create a simple calculating tool to be used for similar laminate structures. Although the utilization of the calculating tool is limited to one manufacturing plant because the primary activity data is dependent of geographical location and for example the discharges of used energy in the plant. The results give an approximation of the climate change potential caused by the laminate. It is although noticed that calculations do not include all environmental impacts of plastic packaging´s life cycle.

Seedlings of Acrocomia aculeata in diferent substrates and protected environments

The seedling production stage is the key to achieve uniformity in tree breeding stage. This study evaluated "bocaiúva" (Acrocomia aculeata) seedling formation, with pre-germinated seeds in different substrates and protected environments, in the University of Mato Grosso do Sul State, Aquidauana, MS. As substrates, we used 100% cattle manure (M), 100% cassava branches (CB), 100% vermiculite (V), 50% cattle manure + 50% cassava branches, 50 % cattle manure + 50% vermiculite, 50% cassava branches + 50% vermiculite and ⅓ cattle manure + ⅓ cassava branches + ⅓ vermiculite. These substrates were tested in a greenhouse covered with 150 µm low density polyethylene (LDPE) film under thermo-reflective screen with 50% shading under film; black screen with 50% shading on the sides; black monofilament screen with 50% shading set on roof and sides; and aluminized thermo- reflective screen with 50% shading set on roof and sides. The completely randomized experimental design with 5 replications of 5 plants each was adopted. Initially, data were submitted to analysis of substrate individual variance in each growing environment, then performing the waste mean square evaluation and their environment joint analysis for comparison. The best growing environment is the thermo-reflective screen compared to LDPE greenhouse and black screen set. All substrates containing manure are recommended for bocaiúva seedlings formation. The pure cassava branch is not indicated for seedling, even using chemical fertilizer.

‘Sweet grape’ tomato post harvest packaging

ABSTRACT This paper aims at evaluating the shelf life of mini tomatoes (Lycopersicum esculentum Mill.) cultivar ‘Sweet Grape’, grown in hydroponics, and stored under environmental and refrigerated conditions inside different packages. We adopted a completely randomized design, in which treatments were combinations of storage conditions: environment (e) and refrigerated (r) with packaging: polyvinyl chloride film (PVC); low-density polyethylene (LDPE); biofilm of tomato fruit of Solanum lycocarpum A.St.-Hil (lobeira) (TFB); cassava starch biofilm (CSB); carnauba wax (Copernicia prunifera) (CW), and without packaging - control (C). Physicochemical and sensory tests were carried out at the beginning (day zero), and at 8, 19, and 33 days of storage (DS). Fruit stored inside PVCr, LDPEe, LDPEr, and CWr had an acceptable shelf life of 33 days. The use of cassava and tomato starches were not effective in controlling fruit fresh weight loss. ‘Sweet Grape’ tomato postharvest conservation was enhanced under refrigerated conditions. The sensory evaluation results revealed that CWr treatment most pleased appraisers, while PCV had the highest rejection rate.

Soursop seedlings: biomasses and biometric relations in different farming environments and substrates – Part II

ABSTRACT The quality of seedling is critical to obtain vigorous plants in the field. The present study aimed to assess biomasses and biometric relations of soursop seedlings. We used different substrates in protected environments. The experiment was performed at the Universidade Estadual do Mato Grosso do Sul (UFMS) (State University of Mato Grosso do Sul). Five farming environments were developed in greenhouses: one covered with low-density polyethylene film (LDPE), another with with polyethylene and heat-reflective cloth under film under 50% shading in aluminized color, monofilament cloth under 50% shading in black, thermo-reflective cloth under 50% shading in aluminized color, and an environment covered with bacuri coconut straw. Substrates were made of manure, humus, cassava branches and vermiculite at different proportions. Each of them varying from 25%, 33.3%, 50% and 75% in mixture combination. Each environment was considered an experiment. A completely randomized design was adopted and later a joint analysis of them. Agricultural greenhouse covered with LDPE and thermo-reflective cloths under 50% of shading, proportionated seedlings with greater biomass. Substrates containing manure are the most suitable for soursop seedlings. High percentages of earthworm humus produce low quality soursop seedlings. Soursop seedlings had a Dickson’s quality index around 0.335. The greenhouse covered only with LDPE film did not produce high quality seedlings.