Series combination of a switched dc-dc converter and a linear regulator for high frequency RF envelope amplifier

Classical linear amplifiers such as A, AB and B offer very good linearity suitable for RF power amplifiers. However, its inherent low efficiency limits its use especially in base-stations that manage tens or hundreds of Watts. The use of linearization techniques such as Envelope Elimination and Restoration (EER) allow an increase of efficiency keeping good linearity. This technique requires a very fast dc-dc power converter to provide variable voltage supply to the power amplifier. In this paper, several alternatives are analyzed to implement the envelope amplifier based on a cascade association of a switched dc-dc converter and a linear regulator. A simplified version of this approach is also suitable to operate with Envelope Tracking technique.

Simulation of AC, DC, and AC-DC coupled mini-grids. In search of the most efficient system

Renewable energy hybrid systems and mini-grids for electrification of rural areas are known to be reliable and more cost efficient than grid extension or only-diesel based systems. However, there is still some uncertainty in some areas, for example, which is the most efficient way of coupling hybrid systems: AC, DC or AC-DC? With the use of Matlab/Simulink a mini-grid that connects a school, a small hospital and an ecotourism hostel has been modelled. This same mini grid has been coupled in the different possible ways and the system’s efficiency has been studied. In addition, while keeping the consumption constant, the generation sources and the consumption profile have been modified and the effect on the efficiency under each configuration has also been analysed. Finally different weather profiles have been introduced and, again, the effect on the efficiency of each system has been observed.

Loss model for a high frequency and low load DC/DC synchronous buck converter

This work presents a behavioral-analytical hybrid loss model for a buck converter. The model has been designed for a wide operating frequency range up to 4MHz and a low power range (below 20W). It is focused on the switching losses obtained in the power MOSFETs. Main advantages of the model are the fast calculation time and a good accuracy. It has been validated by simulation and experimentally with one Ga, power transistor and two Si MOSFETs. Results show good agreement between measurements and the model.

Hybrid behavioral-analytical loss model for a high frequency and low load DC/DC buck converter

This work presents a behavioral-analytical hybrid loss model for a buck converter. The model has been designed for a wide operating frequency range up to 4MHz and a low power range (below 20W). It is focused on the switching losses obtained in the power MOSFETs. Main advantages of the model are the fast calculation time (below 8.5 seconds) and a good accuracy, which makes this model suitable for the optimization process of the losses in the design of a converter. It has been validated by simulation and experimentally with one GaN power transistor and three Si MOSFETs. Results show good agreement between measurements and the model

Bidirectional multiple port dc/dc transformer based on a series resonant converter

In this paper a novel bidirectional multiple port dc/dc transformer topology is presented. The novel concept for dc/dc transformer is based on the Series Resonant Converter (SRC)topology operated at its resonant frequency point. This allows for higher switching frequency to be adopted and enables high efficiency/high power density operation. The feasibility of the proposed concept is verified on a 300W, 700 kHz three port prototype with 390V input voltage and 48V and 12V output voltages. A peak overall efficiency of 93% is measured at full load. A very good load and cross regulation characteristic of the converter is observed in the whole load range, from full load to open circuit. The sensitivity analysis of the resonant capacitance is also performed showing very slight deterioration in the converter performances when a resonant capacitor is changed ±30% of its nominal value.

Power Converter Topologies for a High Performance Transformer Rectifier Unit in Aircraft Applications

This paper presents some power converter architectures and circuit topologies, which can be used to achieve the requirements of the high performance transformer rectifier unit in aircraft applications, mainly as: high power factor with low THD, high efficiency and high power density. The voltage and the power levels demanded for this application are: three-phase line-to-neutral input voltage of 115 or 230V AC rms (360 – 800Hz), output voltage of 28V DC or 270V DC(new grid value) and the output power up to tens of kilowatts.

Full Bridge MMC Converter Optimal Design to HVDC Operational Requirements

This project is funded by RTE, Paris, France

Practical aspects of the use of AC-DC transfer instruments. /

Mode of access: Internet.

Analecta Güstroviensia, h. d., De inclyta Meclenburgensium civitate Güstrovia urbium in vetustissimo Venedorum Principatu principe : quædam ad notitiam antiquariam ac literariam facientia, memoriamque illustrium ac clarissimorum virorum resuscitantia momenta : et variis editorum pariter ac ineditorum documentorum documentorum latebris studiose conquista, & continuo rerum annorumque nexu ita disposita : ut seriem Historiæ Güstroviensis per DC. annos summatin exhibere, rebusq[ue] Meclenburgicis lucem aliquam afferre possint /

Cuts: head and tail pieces, initials.

Operator, organizational, direct support, and general support maintenance manual : motor generator, power supply generator, 60 kw, 120/208, 240/416 volt, 3-phase, 4 wire service, 400 hertz, DC component output, 28 volt, 10 amp, motor input AC, 416 volt, 3-phase, 60 hertz, portable skid mounted (General Dynamics Corp. model 14105008), FSN 6125-917-2244.

"June 1971."

Direct support, general support, and depot maintenance repair parts and special tools lists : welding machine, arc, AC/DC, 300 amp, transformer rectifier, constant current, base mounted (Eutectic Corp. model MD301 FED), FSN 3431-235-4728.

"October 1971."

Operator's manual : grinding kit, valve seat, electric 35 degree angle type concentric drive, 1/4 horsepower, AC/DC, single phase, 115-volt, 14000 RPM rated no load speed (K.O. Lee Company model P300BB) (4910-060-9983) and (K.O. Lee Company model P300BB-M2) (4910-473-6437).

"February 1965."

Operator's manual : grinding kit, valve seat, electric, 35 degree angle, concentric drive, driver, AC/DC, 115-volt, 7,500 RPM rated no load speed (Albertson and Company model 1712-M) (4910-060-9983).

"June 1965."

Operator and organizational maintenance manual (including repair parts and special tool lists) : test stand, automotive generator, alternator, and starter, floor mounted, 10 to 50-V, 500-amp, DC, and 25 to 50-V, 100 to 400 amp, AC, testing ranges, w/800 to 11,000-RPM ... (United Manufacturing Company model AGARTS type II, part number 7336-1 ....

"November 1966."

Operator's manual : grinding machine, machine tool attachment, internal and external grinding, 5" maximum external diameter wheel, 1/4" minimum internal diameter wheel, 4,600 to 42,400 rpm spindle speed, 1/2 hp, AC/DC, 115 V, 60-C, single phase (Dumore series 5) ...

"October 1967."