Avaliação da adição de cargas inorgânicas em EVA-18 e estudo do efeito de agentes interfaciais nas propriedades dos compósitos

Neste trabalho foi realizada a preparação de compósitos tendo como base o uso de poli(etileno-co-acetato de vinila) (EVA) a 18 mol% de acetato de vinila, com cinco tipos diferentes de carga (carbonato de cálcio, sílica, xisto retortado, xisto calcinado e argila sódica), sendo elas usadas naturalmente, funcionalizadas com silano ou tratadas termicamente. As misturas foram processadas durante 15 minutos em câmara de mistura a 160ºC com velocidade dos rotores de 50rpm. Foi verificado que o processamento do EVA não acarretou processos de degradação ou reticulação do polímero. Propriedades mecânicas, calorimetria diferencial de varredura e análises morfológicas foram realizadas para avaliar o efeito da adição de diferentes cargas em distintas concentrações. Os compósitos EVA-18/argila sódica silanizada e EVA-18/xisto calcinado silanizado foram os sistemas que apresentaram os melhores resultados em relação às propriedades mecânicas quando comparado com a matriz polimérica e as demais cargas ensaiadas. O silano teve um papel fundamental na melhoria das propriedades mecânicas. Com apenas 1% (m/m) de argila sódica silanizada obteve-se um aumento de 13% na tensão no ponto de ruptura. Ambos são melhores que o EVA-18/carbonato de cálcio e o EVA-18/sílica comumente utilizados na indústria. Baseando-se nos resultados obtidos, conclui-se que tanto a argila sódica silanizada quanto o xisto calcinado silanizado são alternativas econômicas e eficientes a serem aplicadas como uma possibilidade de escolha de carga para melhorar as propriedades mecânicas do EVA.

Síntese e caracterização de ferrita ni-zn pelo método dos precursores poliméricos calcinada por energia de microondas

Magnetic ceramics have been widely investigated, especially with respect to intrinsic and extrinsic characteristics of these materials. Among the magnetic ceramic materials of technological interest, there are the ferrites. On the other hand, the thermal treatment of ceramic materials by microwave energy has offered various advantages such as: optimization of production processes, high heat control, low consumption of time and energy among others. In this work were synthesized powders of Ni-Zn ferrite with compositions Ni1- xZnxFe2O4 (0.25 ≤ x ≤ 0.75 mols) by the polymeric precursor route in two heat treatment conditions, conventional oven and microwave energy at 500, 650, 800 and 950°C and its structural, and morphological imaging. The materials were characterized by thermal analysis (TG/ DSC), X-ray diffraction (XRD), absorption spectroscopy in the infrared (FTIR), scanning electron microscopy (SEM), X-ray spectroscopy and energy dispersive (EDS) and vibrating sample magnetometry (VSM). The results of X-ray diffraction confirmed the formation of ferrite with spinel-type cubic structure. The extrinsic characteristics of the powders obtained by microwave calcination and influence significantly the magnetic behavior of ferrites, showing particles ferrimagnéticas characterized as soft magnetic materials (soft), is of great technological interest. The results obtained led the potential application of microwave energy for calcining powders of Ni-Zn ferrite

Avaliação do efeito da adição de resíduo de borracha de pneu e brita calcária na formulação de compósitos cimentíceos

Researches have shown that the introduction of rubber in concrete improves the features of its deformability, as well as contributes to environmental disposal of waste generated in the tire retreading process. Furthermore, there is a high availability of limestone within RN and CE country. Ignorance about this stone, does not allow its wide use as aggregate, leaving, this abundant supply idle. A composite of limestone gravel, with proportions of tire rubber waste which could be used as concrete would be an alternative to concrete for low applications. Therefore, this research aims to evaluate the characteristics of concrete containing limestone gravel and proportions of little aggregate replacement (sand) by tire rubber waste. To this goal, the material components of the concrete were characterized, concrete specimens with limestone gravel were made, from the dash 1.0: 2.5: 3.5, varying the water/cement ratio, and inserting a commercial plasticizer, without a proportion of residue, known as reference. From this, concrete with and without the presence of the additive in the same proportions were chosen, as well as these with the use of granite gravel, for being the most used. Selected the references, to these, replacements of little aggregate (sand) were added replaced by rubber waste from the tire retreading process, treated with 1M NaOH in proportions from 5.0 to 20.0 % by mass, cured and exposed to the semiarid environment. The results indicate the possibility of using limestone gravel in the concrete composition with workability correction using plasticizer. There was a decrease in the mechanical properties of the concrete with increments of waste rubber, but there is an improvement in toughness and deformability of the composite, which makes it interesting for the construction of non-structural concrete floors, as well as, the rubber waste delayed the hardening process, continuing to gain resistance after 28 days

Avaliação dos marcadores celulares por citometria de fluxo nos portadores de leucemia mieloide aguda atendidos no Hemocentro do Rio Grande do Norte-Hemonorte

The acute myeloid leukemia (AML) is a disease in which malignant myeloblasts expand, build up and suppress normal hematopoietic activity would represent a major diagnostic challenge. With the advent of immunophenotyping by flow cytometry, the diagnosis of these tumors have become more faithful, facilitating the treatment and monitoring of patients. The objectives of this study: diagnosis and classification of AML based on immunophenotyping by flow cytometry with a panel of AcMo specific for acute leukemias, set the frequency of AML in samples from patients with acute leukemias sent to the Department of Hematology Blood Center of Rio Grande do Norte - HEMONORTE, establish standards of antigen expression for different subtypes of acute leukemia and its correlation with the newly diagnosed cases refractory to treatment and recurrence of the disease, standardization of methods for detection and labeling of surface antigens by flow cytometry and intracytoplasmic flow, and observe the frequency of acute leukemia with aberrant phenotypes rare. During the study, 351 were diagnosed acute leukemia, and 179 (51%) classified as AML and 172 (49%) and ALL, which were excluded from the present work. Of the 179 AML, 92 (51.4%) were female and 87 (48.6%) were male, with ages ranging from 3 to 95 years of ag, with higher incidence in individuals in the age group of 41 to 65. Splenomegaly was the clinical finding more present, a total of 147 cases (82.1%), followed by hepatomegaly present in 132 cases (73.7%). The hemorrhagic events were observed in 55 cases (30.7%). Lymphadenopathy in turn was detected in 20 of 179 cases (11.2%). In order to classify subtypes of AML, we used a large panel of monoclonal antibodies, obtaining the following results: AML M0, 02 (1.1%) AML M1, 40 (22.3) AML M2, 60 (33.5) AML M3, 22 (12.3%) AML M4, 10 (5.6) AML M5, 13 (7.3%) AML M6 06 (3.4%) and AML M7 01 (0.6%). We observed some cases with aberrant expression of some antigens such as CD7, CD4, CD19, CD3, CD5 and TdT, CD 7 was present in 30 (16.8%), CD4 in 5 (2.8%), the CD 3 in 5 (2.8%), the CD19 in 3 (1.7%), the CD5 in 3 (1.7%) and TDT was in 7 (3.9%) cases of AML .the CD8 and CD79a was present in only a 1 case.

Caracterização dos marcadores químicos e avaliação de atividades biológicas do extrato de Spondias mombim

Spondias mombin is a fruitful species dispersed in tropical regions of America, Africa and Asia. In Brazil, the species can be found mainly in the northern and northeastern regions. Scarce chemical and pharmacological studies have been reported for S. mombin and until this moment studies about chemical markers were not developed. In this context, the aims of this study were to characterize the chemical markers from S. mombin leaves and evaluate their anti-inflammatory, antioxidant and antiproliferative potentials. The chemical profile of the hydroethanolic extract from S. mombin leaves analyzed by HPLC-DAD, through a validated method, allowed the identification and quantification of ellagic acid and chlorogenic acid. This extract showed anti-inflammatory potential in acute peritonitis model induced by carrageenan. The hydroethanolic extract from S. mombin leaves was subjected to a liquid-liquid partition with the solvents: n-hexane, dichloromethane, ethyl acetate and n-butanol. Regarding the anti-inflammatory potential of the fractions obtained they were active; however, ethyl acetate fraction at 200 mg/kg showed highlighted results. The compounds ellagic acid and chlorogenic acid also inhibited the leukocyte migration to the site of inflammation at 2.5, 5 and 10 mg/kg. The hydroethanolic extract, fractions and the chemical markers showed significant antioxidant potential when evaluated in different assays: DPPH Free-Radical Scavenging, Superoxide Radical Scavenging, Hydroxyl Radicals Scavenging and Reducing Power. Taken together our results showed that hydroethanolic extract of S. mombin leaves has ellagic acid and chlorogenic acid as bioactive markers and it demonstrated antiinflammatory and antioxidant properties besides no cytotoxicity against 3T3 cells. It enables us to suggest S. mombin as an important species to develop herbal drugs

AVALIAÇÃO DE PLANTAS MATRIZES DE ABACAXIZEIRO CULTIVAR SMOOTH CAYENNE UTILIZANDO MARCADORES RAPD E PADRÕES ISOENZIMÁTICOS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Obtenção de compósitos cerâmicos baseados em Al2O3/TiC através dos precursores poliméricos

The obtaining of ceramic materials from polymeric precursors is subject of numerous studies due to lower energy costs compared to conventional processing. The aim of this study is to investigate and improve the mechanism for obtaining ceramic matrix composite (CMC) based on SiOC/Al2O3/TiC by pyrolysis of polysiloxane in the presence of an active filler and inert filler in the pyrolysis temperature lower than the usually adopted for this technique, with greater strength. It also investigates the influence of pyrolysis temperature, the content of Alas active filler, the presence of infiltrating agents (Al, glass and polymer) after pyrolysis, temperature and infiltration time on some physical and mechanical properties. Alumina is used as inert filler and Al and Ti as active filler in the pyrolysis. Aluminum, glass and polysiloxane are used as agents infiltrating the post-pyrolysis. The results are analyzed with respect to porosity and bulk density by the Archimedes method, the presence of crystalline phases by X-ray diffraction (XRD) and microstructure by scanning electron microscopy (SEM). The ceramic pyrolyzed between 850 °C 1400 °C contain porosity 15% to 33%, density 2.34 g/cm3 and flexural strength at 4 points from 30 to 42 MPa. The microstructure features are porous, with an array of Al2O3 reinforced by TiC particles and AlTi3. The infiltration post-pyrolysis reveals decrease in porosity and increase density and strength. The composites have potential applications where thermal stability is the main requirement

Fabricação de malha de trama utilizada como pré-formas na indústria de compósitos e avaliação das propriedades mecânicas

In the manufacture of composite, textile materials are being used as reinforcement. Generally, the combination of the matrix with the textile material in the form of fibres or yarns is used depending on their distribution in the web. In the present work, in place of fibres or yarns, a knitted structure in the form of the final product which is defined as preform. The preform is weft knit manufactured with polyester filaments. In the manufacture of composite, polyester resin was used as matrix. The physical and mechanical properties as well as the formability of the weft knit were analysed. The physical and mechanical properties as well as the formability of the knitted structure were analysed. The results obtained on the analysis show that the courses and wales of the weft knit structure and the tensile properties help the formability of the structure and the impregnation of the resin. It could be clearly observed that composite structure in the direction of the courses support more tension than in the direction of the wales. In relation to the three points flexural tests it was possible to note that there was more flexion in the direction of wales, what was expected. It was also possible to note that there are other advantages such as reduction in the loss of materials used, homogeneity in the distribution of the knitted structure in the mould, reduction in the preparation time and also in the reduction in the cost of manufacture

Avaliação do comportamento tribológico de compósitos poliéster/fibra de vidro utilizando resíduos de poliéster/fibra de vidro e carbonato de cálcio como carga

The use of composite materials and alternative is being increased every day, as it becomes more widespread awareness that the use of renewable and not harmful to the environment is part of a new environmentally friendly model. Since its waste (primarily fiberglass) can not be easily recycled by the difficulty that still exists in this process, since they have two phases mixed, a polymeric matrix thermoset difficult to recycle because it is infusible and phase of fiber reinforcements. Thermoset matrix composites like Polyester + fiberglass pose a threat due to excessive discharge. Aiming to minimize this problem, aimed to reuse the composite Polyester + fiber glass, through the wastes obtained by the grinding of knifes and balls. These residues were incorporated into the new composite Polyester/Fiberglass for hot compression mold and compared tribological to composites with filler CaCO3, generally used as filler, targeting a partial replacement of CaCO3 by such waste. The composites were characterized by thermal analysis (TGA, DSC and DMA), by the surface integrity (roughness determination, contact angle and surface energy), mechanical properties (hardness) and tribological tests (wear and coefficient of dynamic friction) in order to evaluate the effect of loads and characterize these materials for applications that can take, in the tribological point of view since waste Polyester + fiberglass has great potential for replacement of CaCO3

Obtenção de compósitos cerâmicos reforçados com carbetos refratários a partir de precursores poliméricos

In this work, were produced ceramic matrix composites based in SiCxOy e Al2O3 reinforced with NbC, by hydrosilylation reaction between D4Vi and poly(methylhydrosiloxane) mixtured with Al2O3 as inert filler, Nb and Al as reactive filler. After the mixture and compactation at 80ºC (warm pressing), the samples were pyrolised at 1200 and 1400ºC and infiltred with ICZ and LZSA respectively, and thermically, physical and structurally characterized by X-ray diffraction, density and porosity, flexural mechanical strength and fracture surface by scanning electron microscopy. The yield ceramic obtained after pyrolysis for studied composition at 1200ºC was 95%. The obtained phases had been identified as being Al3Nb, NbSi2 and NbC. The composite material presented apparent porosity varying of 15 up to 32% and mechanical flexural strenght of 32 up to 37,5MPa. After the fracture surface analysis, were observed a phases homogeneous dispersion, with some domains of amorphous and crystalline aspect. The samples that were submitted the infiltration cycle presented a layer next the surface with reduced pores number in relation to the total volume

Avaliação mecânica e microestrutural de compósitos de poliéster com adição de cargas minerais e resíduos industriais

With the current growth in consumption of industrialized products and the resulting increase in garbage production, their adequate disposal has become one of the greatest challenges of modern society. The use of industrial solid residues as fillers in composite materials is an idea that emerges aiming at investigating alternatives for reusing these residues, and, at the same time, developing materials with superior properties. In this work, the influence of the addition of sand, diatomite, and industrial residues of polyester and EVA (ethylene vinyl acetate), on the mechanical properties of polymer matrix composites, was studied. The main objective was to evaluate the mechanical properties of the materials with the addition of recycled residue fillers, and compare to those of the pure polyester resin. Composite specimens were fabricated and tested for the evaluation of the flexural properties and Charpy impact resistance. After the mechanical tests, the fracture surface of the specimens was analyzed by scanning electron microscopy (SEM). The results indicate that some of the composites with fillers presented greater Young s modulus than the pure resin; in particular composites made with sand and diatomite, where the increase in modulus was about 168 %. The composites with polyester and EVA presented Young s modulus lower than the resin. Both strength and maximum strain were reduced when fillers were added. The impact resistance was reduced in all composites with fillers when compared to the pure resin, with the exception of the composites with EVA, where an increase of about 6 % was observed. Based on the mechanical tests, microscopy analyses and the compatibility of fillers with the polyester resin, the use of industrial solid residues in composites may be viable, considering that for each type of filler there will be a specific application

Avaliação da expressão imuno-histoquímica de marcadores de hipóxia em carcinoma epidermóide de língua

The tumor hypoxia modulates a series of genetic changes related to adaptive development, invasion and metastasis of various human cancers, among which squamous cell carcinoma of the tongue (SCCT). The objective of this study was to analyze clinical, morphological and immunohistochemical expression by HIF-1α, GLUT-1 and CA-IX in 57 cases of CEL and correlated this expression to clinical parameters and morphological. After a descriptive analysis of data on gender, age, race, and habits of patients, it was found that the results were consistent with the literature. The clinical and morphological parameters analyzed and the expression of these markers of hypoxia were subjected to statistical analysis (Qui2 test), verifying that they can be used as indicators of the biological behavior of CEL. Among the results of this study, we observed that the intensity of expression for HIF-1α, in most cases located in the cytoplasm and nucleus, statistically correlated with clinical staging (p = 0.011) and histological grading (p = 0.002). As for the relationship between the distribution of labeling for HIF-1α and metastasis, the chi-square (Qui2) showed that there was statistically significant differences between the groups (p = 0.040). 75.8% of the sample who had metastases, there was the predominance of diffuse marking. The immunoexpression cytoplasmic/membrane GLUT-1 showed a statistically significant correlation with the clinical stage (p = 0.002) and histological grading (p = 0.000). Concerning the location of markings for GLUT-1 tumor on the island, there was a predominance of peripheral marking specimens in most low-grade (78.6%). In the sample of high-grade, prevailed the location center/periphery (55.8%). According to the chi-square (Qui2), the location on the island of the tumor (p = 0.025) showed statistically significant difference in histological grading. The immunoreactivity of CA-IX, in most cases located in the membrane and cytoplasm, exhibited a statistically significant correlation with histological grading (p = 0.005). Based on these results, we can conclude a broad participation of these markers of hypoxia in oral carcinogenesis and its possible use as markers of biological behavior and tumor progression in CEL

Avaliação de Diferentes Compósitos na Resistência à Fratura de Núcleos de Preenchimento

Objective: To evaluate and compare the fracture strength of different composite resins used for core buildup. Method: Thirty-six bovine teeth were decoronated at the cervical third to standardize the length of specimens at 20 mm. Under constant irrigation, the canals were prepared with #5 Largo drills corresponding to the size and diameter of #3 Reforpost fiberglass post. The posts were cemented with Enforce resin sealer, being 16 mm inside the root canal and 4 mm outside the root canal, and the material was light-activated for 30 seconds at each side. The specimens were divided into 3 groups (n=12), in which cores (4 mm diameter and 5 mm high) were prepared from a prefabricated standard with three types of composite resins: Group 1: Z100 (3M), Group 2: Z250 (3M) and Group 3: P60 (3M). The specimens were fixed in a cylindrical device with an adaptor at 45o inclination. This device was adapted to a universal testing machine (EMIC) to simulate the force until fracture of the specimen. Data were subjected to ANOVA (p<0.05). Results: The Z250 resin cores presented the highest mean fracture strength (45.453 kgf), while the mean fracture strengths in Group 1 and Group 3 were 38.014 and 39.506 kgf, respectively. P60 caused the largest number of root fractures. Conclusion: Considering the characteristics and properties of the tested resins, Z250 appears as the most indicated for core buildup.

Avaliação clínica, laboratorial e dos marcadores bioquímicos do estresse oxidativo hepatocelular em ratos diabéticos induzidos pela aloxana

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação de candidatos a marcadores moleculares envolvidos no carcinoma renal de células claras

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)