Effectiveness of intraoral suction systems and aspirating tips for evacuation of aluminum oxide particles during use of air-abrasion

Aim: The purpose of this study was to compare the effectiveness of a high-volume evacuation and a conventional intraoral suction system and aspirating tips for capturing aluminum oxide particles during use of an air-abrasion device. Methods: A phantom head was fixed at the dental chair head with secured a metallic device with 5 horizontal shafts, corresponding to operator's clockrelated working positions, and one vertical shaft to simulate the operator's nasal cavity. Petri plates were fixed to the shafts at distances of 20, 40 and 60 cm from the center of the oral cavity of the phantom head to collect the aluminum oxide particles spread over during air abrasion. The dust was aspirated with two types of suction tips used with both suction systems: a conventional saliva ejector and a saliva ejector customized by the adaptation of a 55-mm-diameter funnel. Results: The amount of particles showed that the greatest abrasive particle deposition occurred at a distance of 20 cm from the center of the oral cavity of the phantom head at 9 o'clock operatory position with the conventional saliva ejector attached to high-volume evacuation system. Conclusions: The greatest deposition of aluminum oxide particles occurred at the shortest distance between the operator and the center of the oral cavity, while using the high-volume evacuation system associated to the conventional suction tip.

Bonding all-ceramic restorations with two resins cement techniques: A clinical report of three-year follow-up

Ceramics have been widely used for esthetic and functional improvements. The resin cement is the material of choice for bonding ceramics to dental substrate and it can also dictate the final esthetic appearance and strength of the restoration. The correct use of the wide spectrum of resin luting agents available depends on the dental tooth substrate. This article presents three-year clinical results of a 41 years old female patient B.H.C complaining about her unattractive smile. Two all-ceramic crowns and two laminates veneers were placed in the maxillary incisors and cemented with a self-adhesive resin luting cement and conventional resin luting cement, respectively. After a three-year follow-up, the restorations and cement/teeth interface were clinically perfect with no chipping, fractures or discoloration. Proper use of different resin luting cements shows clinical appropriate behavior after a three-year follow-up. Self-adhesive resin luting cement may be used for cementing all-ceramic crowns with high predictability of success, mainly if there is a large dentin surface available for bonding and no enamel at the finish line. Otherwise, conventional resin luting agent should be used for achieving an adequate bonding strength to enamel.

Development and validation of a D-loop mtDNA SNP assay for the screening of specimens in forensic casework

Mitochondrial DNA (mtDNA) analysis is usually a last resort in routine forensic DNA casework. However, it has become a powerful tool for the analysis of highly degraded samples or samples containing too little or no nuclear DNA, such as old bones and hair shafts. The gold standard methodology still constitutes the direct sequencing of polymerase chain reaction (PCR) products or cloned amplicons from the HVS-1 and HVS-2 (hypervariable segment) control region segments. Identifications using mtDNA are time consuming, expensive and can be very complex, depending on the amount and nature of the material being tested. The main goal of this work is to develop a less labour-intensive and less expensive screening method for mtDNA analysis, in order to aid in the exclusion of non-matching samples and as a presumptive test prior to final confirmatory DNA sequencing. We have selected 14 highly discriminatory single nucleotide polymorphisms (SNPs) based on simulations performed by Salas and Amigo (2010) [1] to be typed using SNaPShotTM (Applied Biosystems, Foster City, CA, USA). The assay was validated by typing more than 100 HVS-1/HVS-2 sequenced samples. No differences were observed between the SNP typing and DNA sequencing when results were compared, with the exception of allelic dropouts observed in a few haplotypes. Haplotype diversity simulations were performed using 172 mtDNA sequences representative of the Brazilian population and a score of 0.9794 was obtained when the 14 SNPs were used, showing that the theoretical prediction approach for the selection of highly discriminatory SNPs suggested by Salas and Amigo (2010) [1] was confirmed in the population studied. As the main goal of the work is to develop a screening assay to skip the sequencing of all samples in a particular case, a pair-wise comparison of the sequences was done using the selected SNPs. When both HVS-1/HVS-2 SNPs were used for simulations, at least two differences were observed in 93.2% of the comparisons performed. The assay was validated with casework samples. Results show that the method is straightforward and can be used for exclusionary purposes, saving time and laboratory resources. The assay confirms the theoretic prediction suggested by Salas and Amigo (2010) [1]. All forensic advantages, such as high sensitivity and power of discrimination, as also the disadvantages, such as the occurrence of allele dropouts, are discussed throughout the article. © 2013 Elsevier B.V.

Estudo comparativo entre a lubri-refrigeração convencional e a MQL no processo de retificação cilíndrica externa de mergulho

Pós-graduação em Engenharia Mecânica - FEB

Diagnose de trincas em sistemas rotativos, utilizando modelos de falhas através da metodologia dos observadores de estados

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito de material cimentante e do tempo na resistência adesiva de pinos de fibra de vidro

Pós-graduação em Ciências Odontológicas - FOAR

Eficiência energética em sistemas de aeração de silos de armazenagem de grãos, utilizando inversores de freqüência

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Revestimento de sementes de milho superdoce

Pós-graduação em Agronomia - FCAV

Opalas gemológicas do Piauí: gênese revelada por microtermometria e minerais associados

As opalas de Pedro II e Buriti dos Montes, no estado do Piauí, constituem as mais importantes ocorrências brasileiras dessa gema, tanto em termos de volume quanto pela qualidade gemológica, que é comparável à das famosas opalas australianas. No entanto, a informalidade na extração e comercialização destas opalas, assim como a falta de informações quanto à gênese destes depósitos não permitem a prospecção por novas jazidas e o estabelecimento de um certificado de procedência para as opalas do Piauí que permitisse sua inserção formal no mercado gemológico internacional. Alguns autores têm se dedicado ao estudo dessas opalas, revelando fortes evidências de sua origem hidrotermal, mas até então, nenhum trabalho abordou as características físico-químicas dos fluidos que teriam originado esses depósitos de opalas. Diante disso, o principal objetivo deste trabalho foi entender o sistema hidrotermal responsável pela gênese das opalas do Piauí, ou seja, caracterizar os fluidos que originaram a mineralização e mostrar sua relação com o contexto geológico da região. Os municípios de Pedro II e Buriti dos Montes se localizam na porção nordeste do estado do Piauí, a aproximadamente 230 km a leste da capital Teresina, e as ocorrências de opala se encontram na porção basal da Bacia do Parnaíba, constituindo veios e vênulas nos arenitos dos grupos Serra Grande (Buriti dos Montes) e Canindé (Pedro II), os quais são seccionados por soleiras e diques de diabásio da Formação Sardinha. Elas também ocorrem cimentando brechas e como depósitos coluvionares e de paleocanal. Associados às opalas, localmente encontram-se veios de quartzo, calcedônia, barita e hematita (ou goethita). De maneira geral, as opalas de Pedro II apresentam jogo de cores, são predominantemente brancas ou azuladas com aspecto leitoso, semitranslúcidas a opacas e com inclusões sólidas pouco aparentes. Em contrapartida, as opalas de Buriti dos Montes não apresentam jogo de cores, a cor varia entre amarelo claro e vermelho amarronzado, são semitransparentes a translúcidas e contêm grande variedade de inclusões sólidas. Os dados obtidos revelam que as opalas de Pedro II são tipicamente do tipo amorfo (opala-A), enquanto as opalas de Buriti dos Montes variam entre amorfas e cristobalita-tridimita (opala-CT). Na opala preciosa, o típico jogo de cores é causado pelo arranjo regular das esferas de sílica que as constituem. A ausência de cimento opalino entre as esferas reforça a beleza desse efeito. Em contrapartida, as opalas laranja não apresentam jogo de cores, mas têm maior transparência devido ao diminuto tamanho das esferas. As inclusões sólidas também produzem belos efeitos nas opalas estudadas, principalmente na variedade laranja, que é mais transparente. Além disso, o conjunto de inclusões sólidas revela características intrínsecas aos processos hidrotermais que originaram as opalas estudadas. Agregados botrioidais, dendríticos e nodulares são exemplos de inclusões formadas por fragmentos dos arenitos hospedeiros carreados pelos fluidos hidrotermais que geraram as opalas. As inclusões sólidas também têm relação direta com a cor das opalas. Nas opalas de Buriti dos Montes, os tons de vermelho, laranja e amarelo são produzidos pela dissolução parcial das inclusões constituídas por oxihidróxidos de Fe. De maneira semelhante, a cor verde nas opalas preciosas está relacionada aos microcristais de Co-pentlandita inclusos nas mesmas. O conjunto de minerais associados às opalas conduz a uma assinatura mineralógicogeoquímica marcada pelos elevados teores de Fe e Al nas opalas com inclusões de hematita/goethita e caulinita, e assim também com aumento considerável dos teores de elementos terras raras nas opalas em que se concentram as inclusões de caulinita e apatita. Entre os elementos-traço, Ba é o mais abundante, e provavelmente foi incorporado pelo fluido hidrotermal, tendo em vista que veios de barita são encontrados com frequência nessa região da Bacia do Parnaíba. Várias feições como estruturas de fluxo nas opalas, corrosão e dissolução parcial dos cristais de quartzo hialino e de inclusões mineralógicas, vênulas de quartzo hidrotermal sobrecrescidas aos grãos detríticos, e zoneamento dos cristais de quartzo confirmam que essas opalas têm origem hidrotermal. A ruptura do Gondwana teria provocado um vasto magmatismo básico fissural, que por sua vez foi responsável pelo aporte de calor que gerou as primeiras células convectivas de fluidos quentes. A água contida nos arenitos certamente alimentou o sistema e se enriqueceu em sílica através da dissolução parcial ou total dos próprios grãos de quartzo dos arenitos. Este fluido hidrotermal foi posteriormente aprisionado em sistemas de fraturas e nelas se resfriou, precipitando a opala e minerais associados.

Avaliação da efetividade de cimentos resinosos auto-adesivos aplicados sob diferentes pré-tratamentos da dentina radicular na resistência adesiva de pinos de fibra de vidro

Pós-graduação em Ciências Odontológicas - FOAR

Bond Strength of Different Resin Cement and Ceramic Shades Bonded to Dentin

Purpose: To evaluate the microtensile bond strength (MTBS) of ceramic cemented to dentin varying the resin cement and ceramic shades.Materials and Methods: Two VITA VM7 ceramic shades (Base Dentine 0M1 and Base Dentine 5M3) were used. A spectrophotometer was used to determine the percentage translucency of ceramic (thickness: 2.5 mm). For the MTBS test, 80 molar dentin surfaces were etched and an adhesive was applied. Forty blocks (7.2 x 7.2 x 2.5 mm) of each ceramic shade were produced and the ceramic surface was etched (10% hydrofluoric acid) for 60 s, followed by the application of silane and resin cement (A3 yellow and transparent). The blocks were cemented to dentin using either A3 or transparent cement. Specimens were photoactivated for 20 s or 40 s, stored in distilled water (37 degrees C/24 h), and sectioned. Eight experimental groups were obtained (n = 10). Specimens were tested for MTSB using a universal testing machine. Data were statistically analyzed using ANOVA and Tukey's post-hoc tests (alpha <= 0.05).Results: The percentage translucency of 0M1 and 5M3 ceramics were 10.06 (+/- 0.25)% and 1.34 (+/- 0.02)%, respectively. The lowest MTBS was observed for the ceramic shade 5M3. For the 0M1 ceramic, the A3 yellow cement that was photocured for 20 s exhibited the lowest MTBS, while the transparent cement that was photocured for 40 s presented the highest MTBS.Conclusions: For the 2.5-mm-thick 5M3 ceramic restorations, the MTBS of ceramic cemented to dentin significantly increased. The dual-curing cement Variolink II photocured for 40 s is not recommended for cementing the Base Dentine 5M3 feldspathic ceramic to dentin.

Análise histopatológica do comportamento pulpar, pós cimentação de coroas totais metálicas com cimentos de ionômero vítreo e fosfato de zinco

Pós-graduação em Odontologia Restauradora - ICT

Discrepâncias de assentamento ocorrido em coroas totais metálicas, com e sem alívio interno, variando-se os términos cervicais e os agentes cimentantes

Pós-graduação em Odontologia Restauradora - ICT

Otimização dinâmica de rotores com eixos em compósito

Pós-graduação em Engenharia Mecânica - FEG

A MICROSTRAIN COMPARISON OF PASSIVELY FITTING SCREW-RETAINED AND CEMENTED TITANIUM FRAMEWORKS

Statement of problem. An imprecise fit between frameworks and supporting dental implants in loaded protocols increases the strain transferred to the periimplant bone, which may impair healing or generate microgaps.Purpose. The purpose of this study was to investigate the microstrain between premachined 1-piece screw-retained frameworks (group STF) and screw-retained frameworks fabricated by cementing titanium cylinders to the prefabricated framework (group CTF). This procedure was developed to correct the misfit between frameworks and loaded implants.Material and methods. Four internal hexagon cylindrical implants were placed 10 mm apart in a polyurethane block by using the surgical guides of the corresponding implant system. Previously fabricated titanium frameworks (n=10) were divided into 2 groups. In group STF, prefabricated machined frameworks were used (n=5), and, in group CTF, the frameworks were fabricated by using a passive fit procedure, which was developed to correct the misfit between the cast titanium frameworks and supporting dental implants (n=5). Both groups were screw-retained under torque control (10 Ncm). Six strain gauges were placed on the upper surface of the polyurethane block, and 3 strain measurements were recorded for each framework. Data were analyzed with the Student t test (alpha=.05).Results. The mean microstrain values between the framework and the implants were significantly higher for group STF (2517 me) than for group CTF (844 me) (P<.05).Conclusions. Complete-arch implant frameworks designed for load application and fabricated by using the passive fit procedure decreased the strain between the frameworks and implants more than 1 piece prefabricated machined frameworks.