钠原子激光增强电离光谱研究—以石墨杯为原子化器 原子吸收光谱法对发样中Zn、Cu、Mn、Ap的测定

、I钠原子激光增强电离光谱(LEIS)方法的研究-以石墨杯为原子化器在LEIS方法中，最常见的原子化器是火焰。但由于火焰背景噪声严重且难以克服，在火焰原子化过程中，雾化和热离解不充分，仅有10~(-2)%的分析溶液参与吸收以及火焰气体使测定元素受到高度稀释等不利因素的影响，火焰原子化限制了LEIS方法灵敏度的进一步提高。考虑到石墨炉原子化器较火焰具有取样量少，绝对灵敏度高；样品（包括固态、液态）可直接引入石墨炉内；不会发生如同火焰中所存在的干扰效应；蒸发效率和原子化效率较高，几乎全部样品都能参与吸收等优点，本工作在已建立火焰LEIS方法的实验基础上，将原子化器改换为石墨杯进行了钠原子LEIS方法的研究。到目前为止，国内外仅有的几篇有关石黑炉LEIS的研究报告中，都报导了该方法对钠原子的检出限估计可达到10~(-14)-10~(-15)克，由于此项研究尚处于探索性研究阶段，故有关方法性的系统研究几乎还未见报导。本工作在未使用任何放大器的情况下（实验条件限制）对影响钠原子LEIS信号强度的诸因互进行了实验观察。主要包括：钠原子化条件；激光束位置、阳极电压、激光输出能量、电极位置以及激光脉冲重复率对LEIS信号强度的影响等。并绘制了校准曲线，统计方法的相对标准偏差分别为11%（高浓度）18.2%（低浓度），在现有仪器条件下，还不能测出检出限，测定下限为3*10~(-9)克。对固体粉末直接进行了尝试，检测下限为5*10~(-8)克，进样是为5毫克。在进一步的研究工作中，如有条件使用低噪声的放大器及Bxear积分器，选择门检时间窗，或采用分步激发等手段，估计本方法定会达到预想的高灵敏度，检敏度至少提高了个数量级。对石墨炉原子化LEIS法来说，似比较详细的研究报告，截至实验停止时还未见报导。II原子吸收光谱法对发样中Zn、Cu、Mn、Al的测定发中微量元素ZN、Cu、Mn均属人体必需元素，与人体的生长发育和多种生理功能，临床医学等方面有着极为密切的关系，而Al则被认为是异致某种疾病的元素之一。本工作报告了用火焰法测定Zn、Cu；石墨炉法测定Al、Mn的结果，其中，对Al的测定，为摆脱基体干扰，加入改进剂Mg(NO_3)_2，并采用平台石墨炉进行试验，得到了线性较好的工作曲线，但在实际测定时，由于实验条件的限制，只能采用一般石墨管加基体改进剂对少娄样品中Al含量进行测定。Zn、Cu、Al三种元素由标准曲线法测定；而Mn由于Fe的干扰无法消除而采用标准加入法测定，并因此限制了测定样品数。Cu、ZN、Mn三种元素的回收率分别为102.8%, 99.7%, 102.5%，变异系数为9.6%, 11.3%, 9.7%，对本地居民发中（30个发样）Zn、Cu含量进行测定，Zn、Cu的含量范围为148-318ppm，7.2-15ppm，并计算了Zn/Cu比。本方法对发样中四种元素的测定结果与ICP法进行对照。两种方法测定结果吻合得较好。

Theoretical studies on the reaction mechanism of oxidation of primary alcohols by Zn/Cu(II)-phenoxyl radical catalyst

The catalytic mechanism for the oxidation of primary alcohols catalyzed by the two functional models of galactose oxidase (GOase), M-II L (M = Cu, Zn; L = N,N'-bis(3,5-di-tert-butyl-2-hydroxyphenyl)1-2-diiminoquinone)), has been studied by use of the density functional method B3LYP The catalytic cycle of Cu- and Zn-catalysts consists of two parts, namely, substrate oxidation (primary alcohol oxidation) and O-2 reduction (catalyst regeneration). The catalytic mechanisms have been studied for the two reaction pathways (route 1 and route 2). The calculations indicate that the hydrogen atom transfer within the substrate oxidation part is the rate-determining step for both catalysts, in agreement with the experimental observation.

Efeitos da suplementação de fitase sobre a disponibilidade aparente de Mg, Ca, Zn, Cu, Mn e Fe em alimentos vegetais para a tilápia-do-nilo

Cem juvenis de tilápia-do-nilo (Oreochromis niloticus; PV = 100.0 ± 5.0 g) foram distribuídos em 10 tanques-rede com o objetivo de avaliar o efeito da suplementação da enzima fitase (0, 1.000 e 2.000 UFA/kg) sobre a disponibilidade de minerais em alguns alimentos energéticos (milho, milho extrusado, farelo de trigo, farelo de arroz e farelo de sorgo) e protéicos (farelo de soja extrusado, farelo de soja, farelo de girassol, farelo de algodão e glúten de milho) utilizados na alimentação de tilápia-do-nilo (Oreochromis niloticus). Para determinação dos coeficientes de disponibilidade aparente (CDA) do cálcio (Ca), magnésio (Mg), zinco (Zn), cobre (Cu), ferro (Fe) e manganês (Mn), foram confeccionadas 31 rações, marcadas com 0,10% de óxido de crômio III uma referência (ração purificada) e 30 contendo os dez alimentos e os diferentes níveis de suplementação da enzima fitase. O CDA dos nutrientes foi calculado com base no teor de crômio da ração e das fezes. A fitase aumenta, nos vegetais, a disponibilidade do Mg, Cu, Zn e Mn, os quais apresentam tendência diferenciada, em razão do seu valor biológico e do nível de suplementação de enzima.

Local Electrochemical Investigation of Single Grains of Polycrystalline Cu-16%Zn-8%Al Alloy

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

On the electrochemical behavior of Cu-16%Zn-6.5%Al alloy containing the β'-phase (martensite) in borate buffer

In this work, the electrochemical behavior of Cu-16(wt.%)Zn-6.5(wt.%)Al alloy containing the β'-phase (martensite) was studied in borate buffer solution (pH 8.4) by means of open-circuit potential (EOC), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The alloy EOC was -0.29 V vs. Hg/HgO/OH-, similar to that of pure copper in this medium, indicating that the processes which occur on the alloy surface are mainly governed by copper. EIS response was related to the dielectric and transmission properties of the complex oxide layer. The CVs showed peaks concerning the redox reactions for copper and zinc. These peaks were assigned to the formation and reduction of copper and zinc species. Furthermore, they showed that the copper oxidation was suppressed by the presence of zinc and aluminum in the alloy composition. The copper and zinc oxidation to form complex oxide layers and the reduction of the different metallic oxides generated in the anodic potential scan suggest that a solid state reaction could determine the metallic oxide formation. © 2013 Elsevier Ltd. All rights reserved.

Determinação de Cd, Cu, Ni, Pb e Zn em águas marinhas oriundas da Bacia Potiguar utilizando a técnica de difusão em filmes finos por gradiente de concentração (DGT)

The DGT technique has been used to determine and better understand the dynamics and bioavailability of metals in the sea near to marine outfalls. In this work, the DGT was assessed for the determination of Cd, Pb, Cu, Zn and Ni in marine water samples from Potiguar Basin in its conventional aspect (binding agent, Chelex-100 and diffusive agent: Diffusive polyacrylamide gel (D) and restrictive (R)) and determination of Pb and Cd through its alternative aspect (binding agent: Saccharomyces cerevisiae immobilized in agarose gels and diffusive agent: 3MM Chromatography Paper). The deployment curves for long periods of immersion in the sample, showed a good linear correlation for the conventional aspect to Zn (D: R²=0.9586, R: R²=0.9444), Ni (D: R²=0.9789, R: R²=0.9286) and Cu (D: R²=0.764, R: R²=0.8143), and alternative to Pb (R²=0.9228) and Cd (R²=0.9673). The results of the organic and inorganic composition analysis in conventional aspect, showed that for every element there is no significant fraction of organic compounds in the sample. In addition, considering the alternative aspect, the comparison of obtained and expected masses suggests that some of the Pb is not labile and that the main retention mechanism of Pb for S. Cerevisiae occurs through ion exchange

Wspomagana fitoekstrakcja metali śladowych: Cu, Cd, Zn, Pb

Wydział Biologii

Characterization of precursors to methanol synthesis catalysts Cu/ZnO system

The composition of a series of hydroxycarbonate precursors to copper/zinc oxide methanol synthesis catalysts prepared under conditions reported as optimum for catalytic activity has been studied. Techniques employed included thermogravimetry (TG), temperature-programmed decomposition (TPD), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), and Raman and FTIR spectroscopies. Evidence was obtained for various structural phases including hydrozincite, copper hydrozincite, aurichalcite, zincian malachite and malachite (the concentrations of which depended upon the exact Cu/Zn ratio used). Significantly, previously reported phases such as gerhardite and rosasite were not identified when catalysts were synthesized at optimum solution pH and temperature values, and after appropriate aging periods. Calcination of the hydroxycarbonate precursors resulted in the formation of catalysts containing an intimate mixture of copper and zinc oxides. Temperature-programmed reduction (TPR) revealed that a number of discrete copper oxide species were present in the catalyst, the precise concentrations of which were determined to be related to the structure of the catalyst precursor. Copper hydrozincite decomposed to give zinc oxide particles decorated by highly dispersed, small copper oxide species. Aurichalcite appeared to result ultimately in the most intimately mixed catalyst structure whereas zincian malachite decomposed to produce larger copper oxide and zinc oxide grains. The reason for the stabilization of small copper oxide and zinc oxide clusters by aurichalcite was investigated by using carefully selected calcination temperatures. It was concluded that the unique formation of an 'anion-modified' oxide resulting from the initial decomposition stage of aurichalcite was responsible for the 'binding' of copper species to zinc moieties.

On-line voltammetric monitoring of dissolved Cu and Ni in the Gulf of Cadiz, south-west Spain

Geochemical processes in estuarine and coastal waters often occur on temporally and spatially small scales, resulting in variability of metal speciation and dissolved concentrations. Thus, surveys, which are aimed to improve our understanding of metal behaviour in such systems, benefit from high-resolution, interactive sampling campaigns. The present paper discusses a high-resolution approach to coastal monitoring, with the application of an automated voltammetric metal analyser for on-line measurements of dissolved trace metals in the Gulf of Cadiz, south-west Spain. This coastal sea receives metal-rich inputs from a metalliferous mining area, mainly via the Huelva estuary. On-line measurements of dissolved Cu, Zn, Ni and Co were carried out on-board ship during an eight-day sampling campaign in the study area in June 1997. A pumping system operated continuously underway and provided sampled water from a depth of ca. 4 m. Total dissolved metal concentrations measured on-line in the Gulf of Cadiz ranged between <5 nM Cu (<3 nM Ni) ca. 50 km off-shore and 60–90 nM Cu (5–13 nM Ni) in the vicinity of the Huelva estuary. The survey revealed steep gradients and strong tidal variability in the dissolved metal plume extending from the Huelva estuary into the Gulf of Cadiz. Further on-line measurements were carried out with the automatic metal monitor from the bank of the Odiel estuary over a full tidal cycle, at dissolved metal concentrations in the μM range. The application confirmed the suitability of the automated metal monitor for coastal sampling, and demonstrated its adaptability to a wide range of environmental conditions in the dynamic waters of estuaries and coastal seas. The near-real time acquisition of dissolved metal concentrations at high resolution enabled an interactive sampling campaign and therefore the close investigation of tidal variability in the development of the Huelva estuary metal plume.

Síntesi, estructura i reactivitat de nous complexos de Cu, Ag i Ni contenint lligands triazamacrocíclics. Aplicacions en l'activació d'enllaços

· S'ha preparat i caracteritzat una família de complexos de Cu(III) contenint lligands triazamacrocíclics, estudiant-se les seves propietats estructurals, espectroscòpiques i redox. Aquesta àmplia família de complexos tenen un gran interès perquè permeten descriure les propietats dels complexos de Cu en un estat d'oxidació poc habitual i a més ens han permès mesurar de manera quantitativa l'efecte Meyerstein. · Una nova família de complexos de Cu(I) amb els lligands triazamacrocíclics es sintetitzada i caracteritzada per tècniques espectroscòpiques i estructurals, demostrant que aquests complexos presenten diferents estructures a l'estat sòlid i en dissolució. Així doncs, mentre que en dissolució es demostra per RMN que es tracta d'una espècie monomèrica, la determinació estructural per difracció de raigs X d'aquests complexos de Cu(I), ens confirma la formació d'espècies polimèriques. Per altra banda, s'ha estudiat la seva reactivitat; a) la seva implicació en la formació de lligands deuterats mitjançant l'intercanvi H/D en condicions suaus i b) la formació de complexos bisfenoxo a partir de la reactivitat entre els corresponents complexos de Cu(I) i oxigen molecular. De la mateixa manera, s'ha preparat el corresponent anàleg de Ag(I) en estat sòlid, obtenint la formació d'un polímer de Ag(I), el qual presenta a l'estat sòlid una estructura en forma de ziga-zaga, diferent a l'estructura del polímer de Cu(I), que és lineal. · S'ha determinat i proposat el mecanisme que té lloc en l'activació de l'enllaç C-H i posterior reacció de transferència per tal d'estabilitzar els productes finals mitjançant una reacció de desproporció. El seguiment de la reacció té lloc mitjançant tècniques espectroscòpiques com UV-vis. Dit seguiment, ens permet determinar les diferents influències electròniques sobre la reacció de formació dels complexos organometàl·lics de Cu(III). A més a més, el seguiment de la reacció a baixa temperatura ens permet determinar espectroscòpica i teòricament la formació d'un intermedi de Cu(II), i mitjançant la determinació dels paràmetres cinètics i termodinàmics es proposa un mecanisme de reacció. Posteriorment, s'ha assajat la reactivitat d'una sal de Cu(II) amb un lligand macrocíclic que conté un grup metil en el carboni orientat cap al centre del macrocicle, implicant la formació d'un intermedi agòstic. De la determinació estructural d'aquest intermedi de CuII i del lligand protonat, s'extreuen una sèrie de conclusions molt interessants, com són la demostració estructural de l'activació de l'enllaç C-C en la primera etapa de formació i de manera anàloga poder comparar-ho amb els sistemes macrocíclics HL2-HL6, demostrant la possible formació d'un intermedi agòstic, on es produeix l'activació de l'enllaç C-H. Aquesta similitud estaria d'acord amb els sistemes HL2-HL6, els quals espectroscòpica i teòricament s'havia detectat la presència d'un intermedi de característiques similars. Degut a l'acidesa d'aquest protó, i gràcies a la presència d'una base com és el propi lligand, aquest podia ésser extret donant lloc a la formació dels corresponents organometàl·lics de Cu(III). Dita estructura també representa un dels pocs exemples d'un organometàl·lic de CuII, un estat d'oxidació poc conegut dins d'aquest camp. · S'ha descrit la reactivitat dels nous complexos organometàl·lics de Cu(III), els quals sota medi pròtic i en condicions àcides o neutres són espècies totalment estables, però en condicions bàsiques o reductores aquestes espècies reaccionen donant lloc a la formació de noves espècies de tipus bisfenoxo, on el Cu es troba en estat d'oxidació +2. S'han caracteritzat mitjançant difracció de RX, on es s'observa l'entorn químic del Cu, la geometria del complex bisfenoxo i l'hidroxilació de l'anell aromàtic. · Finalment, s'ha descrit per primera vegada la síntesi i caracterització d'uns nous complexos organometàl·lics de Ni. Aquests són sintetitzats en base als càlculs teòrics realitzats sobre els nostres sistemes macrocíclics. Per aquests complexos hem investigat l'efecte del metall, canviant el coure per altres metalls de la primera sèrie de transició (Mn, Fe, Co, Ni, Cu, Zn) i de la segona sèrie de transició (Ru, Rh, Pd, Ag). Els resultats demostren que el Ni(II), és el metall que presenta una major capacitat de l'activació de l'enllaç C-H en aquests sistemes aromàtics. Aquests compostos s'oxiden lentament cap a complexos de Ni(III). Per altra banda, l'addició d'una sal de clor sobre una solució d'un complex de Ni(II) permet aïllar el corresponent complex de Ni(III), caracteritzat per ressonància de spin electrònic

A NEW CU-BASED SMA WITH EXTREMELY HIGH MARTENSITIC-TRANSFORMATION TEMPERATURES

A new series of high temperature copper based shape memory alloys has recently been patented. These alloys contain 8-20 wt% Al, 1-20 wt% Ag, 0-2 wt% of a minor element (preferably Co), balance copper. The martensitic start transformation temperatures of these alloys are above 200 degrees C and, in some cases, they have good high temperature stability and may be useful in commercial applications where higher operating temperatures than those obtained from Cu-Zn-Al and Cu-Al-Ni shape memory alloys are required.

Obtenção e avaliação das potencialidades biológicas de complexos metálicos de 'ZN' e 'CO' contendo proteínas hidrolisadas do soro do leite

Pós-graduação em Química - IQ

Thin films of Cu, In and Sb chalcogenides as photovoltaic absorbers

Many different photovoltaic technologies are being developed for large-scale solar energy conversion such as crystalline silicon solar cells, thin film solar cells based on a-Si:H, CIGS and CdTe. As the demand for photovoltaics rapidly increases, there is a pressing need for the identification of new visible light absorbing materials for thin-film solar cells. Nowadays there are a wide range of earth-abundant absorber materials that have been studied around the world by different research groups. The current thin film photovoltaic market is dominated by technologies based on the use of CdTe and CIGS, these solar cells have been made with laboratory efficiencies up to 19.6% and 20.8% respectively. However, the scarcity and high cost of In, Ga and Te can limit in the long-term the production in large scale of photovoltaic devices. On the other hand, quaternary CZTSSe which contain abundant and inexpensive elements like Cu, Zn, Sn, S and Se has been a potential candidate for PV technology having solar cell efficiency up to 12.6%, however, there are still some challenges that must be accomplished for this material. Therefore, it is evident the need to find the alternative inexpensive and earth abundant materials for thin film solar cells. One of these alternatives is copper antimony sulfide(CuSbS2) which contains abundant and non-toxic elements which has a direct optical band gap of 1.5 eV, the optimum value for an absorber material in solar cells, suggesting this material as one among the new photovoltaic materials. This thesis work focuses on the preparation and characterization of In6Se7, CuSbS2 and CuSb(S1-xSex)2 thin films for their application as absorber material in photovoltaic structures using two stage process by the combination of chemical bath deposition and thermal evaporation.

Characterisation of soluble components and PAH in PM10 atmospheric particulate matter in Brisbane

Fours sets of PM10 samples were collected in three sites in SEQ from December 2002 to August 2004. Three of these sets of samples were collected by QLD EPA as a part of their regular air monitoring program at Woolloongabba, Rocklea and Eagle Farm. Half of the samples were used in this study for the analysis of water-soluble ions, which are Na+, K+, Mg2+, Ca2+, NH4 +, Cl-, NO3 -, SO4 2-, F-, Br-, NO2 -, PO4 -3 and the other half was retained by QLD EPA. The fourth set of samples was collected at Rocklea, specifically for this study. A quarter of the samples obtained from this set of samples were used to analyse water-soluble ions; a quarter of the sample was used to analyse Pb, Cu, Al, Fe, Mn and Zn; and the rests were used to analyse US EPA 16 priority PAHs. The water-soluble ions were extracted ultrasonically with water and the major watersoluble anions as well as NH4 + were analysed using IC. Na+, K+, Mg2+, Ca2+ Pb, Cu, Al, Fe, Mn and Zn were analysed using ICP-AES while PAHs were extracted by acetonitrile and analysed using HPLC. Of the analysed water-soluble ions, Cl-, NO3 -, SO4 2-, Na+, K+, Mg2+ and Ca2+ were high in concentration and determined in all the samples. F-, Br-, NO2 -, PO4 -3 and NH4 + ions were lower in concentration and determined only in some samples. Na+ and Cl- were high in all samples indicating the importance of a marine source. Principal Component Analysis (PCA) was used to examine the temporal variations of the water-soluble ions at the three sites. The results indicated that there was no major difference between the three sites. However, comparing the average concentrations of ions and Cl-/Na+ it was concluded that Woolloongabba had more marine influence than the other sites. Al, Fe and Zn were detected in all samples. Al and Fe were high in all samples indicating the significance of a source of crustal matter. Cu, Mn and Pb were in low concentrations and were determined only in some samples. The lower Pb concentrations observed in the study than in previous studies indicate that the phasing-out of leaded petrol had an appreciable impact on Pb levels in SEQ. This study reports for the first time, simultaneous data on the water-soluble, metal ion and PAH levels of PM10 aerosols in Brisbane, and provides information on the most likely sources of these chemical species. Such information can be used alongside those that already exist to formulate PM10 pollution reduction strategies for SEQ in order to protect the community from the adverse effects of PM pollution.

Spectroscopy of selected copper group minerals : Ktenasite, orthoserpierite and Kipushite

The near-infrared (NIR) and infrared (IR) spectroscopy has been applied for characterisation of three complex Cu-Zn sulphate/phosphate minerals, namely ktenasite, orthoserpierite and kipushite. The spectral signatures of the three minerals are quite distinct in relation to their composition and structure. The effect of structural cations substitution (Zn2+ and Cu2+) on band shifts is significant both in the electronic and vibrational spectra of these Cu-Zn minerals. The variable Cu:Zn ratio between Zn-rich and Cu-rich compositions shows a strong effect on Cu(II) bands in the electronic spectra. The Cu(II) spectrum is most significant in kipushite (Cu-rich) with bands displayed at high wavenumbers at11390 and 7545 cm-1. The isomorphic substitution of Cu2+ for Zn2+ is reflected in the NIR and IR spectroscopic signatures. The multiple bands for 3 and 4 (SO4)2- stretching vibrations in ktenasite and orthoserpierite are attributed to the reduction of symmetry to the sulphate ion from Td to C2V. The IR spectrum of kipushite is characterised by strong (PO4)3- vibrational modes at 1090 and 990 cm-1. The range of IR absorption is higher in Ktenasite than in kipushite while it is intermediate in orthoserpierite.