Studies in bubble formation — III

Bubble formation from single horizontal orifices submerged in Newtonian liquids has been investigated for such chamber volumes that both the pressure inside the chamber and flow rate into the bubble are time dependent. The data collected show that under these conditions the bubble volume decreases exponentially with increase in orifice submergence. The equations for the generalized two stage model of bubble formation, taking the variation of gas flow rate with time into account, have been derived. These equations reduce to the cases of constant gas flow rate and constant pressure when adequate constraints are imposed. The results obtained under intermediate conditions have been quantitatively explained on the basis of these equations.

Studies in bubble formation—II bubble formation under constant pressure conditions

Bubble formation under constant pressure conditions has been investigated for wide range of variation of liquid properties.Air bubbles were formed from single horizontal orifices submerged in liquids whose viscosity varied from 1·0 to 600 cPs and surface tension from 37 to 72 dyn/cm. Air flow rate was varied from 2 to 250 cm3/sec and the orifice diameter from 0·0515 to 0·4050 cm.

Studies in bubble formation—I bubble formation under constant flow conditions

A model based on two step mechanism of bubble formation is proposed. The resulting equations are used to explain the discrepancies existing in the literature. Data have been collected over a wide range of variables to test the model.

Thermal expansion of caesium bromide

The temperature variation of the coefficient of thermal expansion of caesium bromide has been computed in quasiharmonic approximation and compared with the experimental results.

The effect of viscosity and surface tension on the Taylor instability of the surface of a cavitation bubble*

This paper is devoted to a consideration of the following problem: A spherical mass of fluid of density varrho1, viscosity μ1 and external radius R is surrounded by a fluid of density varrho2 and viscosity μ2.The fluids are immiscible and incompressible. The interface is accelerated radially by g1: to study the effect of viscosity and surface tension on the stability of the interface. By analyzing the problem in spherical harmonics the mathematical problem is reduced to one of solution of the characteristic determinant equation. The particular case of a cavity bubble, where the viscosity μ1 of the fluid inside the bubble is negligible in comparison with the viscosity μ2 of the fluid outside the bubble, is considered in some detail. It is shown that viscosity has a stabilizing role on the interface; and when g1 > T(n − 1) (n + 2)/R2(varrho2 − varrho1) the stabilizing role of both viscosity and surface tension is more pronounced than would result when either of them is taken individually.

Studies in bubble formation - IV: bubble formation at porous discs

Bubble formation from porous discs submerged in liquids of different physical properties has been investigated. It is found the number of sites effective for bubble formation is much smaller than the total potentially available sites. The number of effective sites is found to be a function of the surface tension, viscosity, and density of the liquid and the gas flow rate through the disc. A model proposed on the basis of bubble formation from an isolated nozzle and the close packed arrangement of the formed bubbles, explains the phenomenon adequately. © 1970.

A unified approach to bubble and drop formation

An approach, starting with the bubble formation model of Khurana and Khumar, has been presented, which is found to be reasonably applicable to the formation of both bubbles and drops from single submerged nozzles. The model treats both the phenomena jointly as the formation of a dispersed phase entity resulting from injection, whose size depends upon operating parameters and physical properties.

Agricultural expansion and climate change in the Taita Hills, Kenya: an assessment of potential environmental impacts

The indigenous cloud forests in the Taita Hills have suffered substantial degradation for several centuries due to agricultural expansion. Currently, only 1% of the original forested area remains preserved in this region. Furthermore, climate change imposes an imminent threat for local economy and environmental sustainability. In such circumstances, elaborating tools to conciliate socioeconomic growth and natural resources conservation is an enormous challenge. This dissertation tackles essential aspects for understanding the ongoing agricultural activities in the Taita Hills and their potential environmental consequences in the future. Initially, alternative methods were designed to improve our understanding of the ongoing agricultural activities. Namely, methods for agricultural survey planning and to estimate evapotranspiration were evaluated, taking into account a number of limitations regarding data and resources availability. Next, this dissertation evaluates how upcoming agricultural expansion, together with climate change, will affect the natural resources in the Taita Hills up to the year 2030. The driving forces of agricultural expansion in the region were identified as aiming to delineate future landscape scenarios and evaluate potential impacts from the soil and water conservation point of view. In order to investigate these issues and answer the research questions, this dissertation combined state of the art modelling tools with renowned statistical methods. The results indicate that, if current trends persist, agricultural areas will occupy roughly 60% of the study area by 2030. Although the simulated land use changes will certainly increase soil erosion figures, new croplands are likely to come up predominantly in the lowlands, which comprise areas with lower soil erosion potential. By 2030, rainfall erosivity is likely to increase during April and November due to climate change. Finally, this thesis addressed the potential impacts of agricultural expansion and climate changes on Irrigation Water Requirements (IWR), which is considered another major issue in the context of the relations between land use and climate. Although the simulations indicate that climate change will likely increase annual volumes of rainfall during the following decades, IWR will continue to increase due to agricultural expansion. By 2030, new cropland areas may cause an increase of approximately 40% in the annual volume of water necessary for irrigation.

Thermal expansion of triglycine sulphate

Matthias, Miller and Remeika1 were the first to observe that triglycine sulphate becomes ferroelectric below 47°C. The dielectric properties and the specific heat of this crystal have been studied through the transition temperature by Hoshino, Mitsui, Jona and Pepinsky2. The observed variation of the dielectric properties as a function of temperature in this crystal shows that the transition is of second order. Hoshino et al. concluded that the anomaly is not of the λ-type, since their specific heat - temperature curve showed only a hump. It was decided to investigate the thermal expansion of this crystal as it might throw some light on the nature of the transition.

A note on the observed anisotropy in linear compressibility and thermal expansion of quasicrystals

The linear compressibility and the thermal expansion of Al-Fe and Al-Mn quasicrystals have been reported to be anisotropic. The authors suggest that the observed anisotropy in these properties could be due to the presence of decagonal quasicrystals rather than icosahedral quasicrystals.

Thermal expansion and phase transition in NaVO3

The present x-ray study has been undertook in order to correlate the phase transition in sodium metavanadate NaVO3 crystal with its structural aspects. The thermal expansion behaviour of NaVO3 was studied from room temperature up to 500 C, well beyond the transition temperature.

Thermal expansion of doped lanthanum gallates

Thermal expansion of several compositions of Sr and Mg-doped LaGaO3 including an A-site deficient composition (La0.9Sr0.1)(0.98)(Ga0.8Mg0.2)O-2.821 were measured in the temperature range from 298 to 1273 K. The effect of doping on thermal expansion was studied by varying the composition at one site of the perovskite structure (either A or B), while keeping the composition at the other site invariant. Thermal expansion varied nonlinearly with temperature and exhibited an inflexion between 550 and 620 K, probably related to the change in crystal structure from orthorhombic to rhombohedral. The dependence of average thermal expansion coefficient (alpha (av)) on the dopant concentration on either A or B site of the perovskite structure was found to be linear, when the composition at the other site was kept constant. Mg doping on the B-site had a greater effect on the average thermal expansion coefficient than Sr doping on the A-site. Cation deficiency at the A-site decreases thermal expansion when compositions at both sites are held constant.

Effect of wall thickness on the end corrections of the extended inlet and outlet of a double-tuned expansion chamber

Simple expansion chambers, the simplest of the muffler configurations, have very limited practical application due to the presence of periodic troughs in the transmission loss spectrum which drastically lower the overall transmission loss of the muffler. Tuned extended inlet and outlet can be designed to nullify three-fourths of these troughs, making use of the plane wave theory. These cancellations would not occur unless one altered the geometric lengths for the extended tube in order to incorporate the effect of evanescent higher-order modes (multidimensional effect) through end corrections or lumped inertance approximation at the area discontinuities or junctions. End corrections of the extended inlet and outlet have been studied by several researchers. However the effect of wall thickness of the inlet/outlet duct on end correction has not been studied explicitly. This has significant effect on the tuning of an extended inlet/outlet expansion chamber. It is investigated here experimentally as well as numerically (through use of 3-D FEM software) for stationary medium. Crown Copyright (C) 2010 Published by Elsevier Ltd. All rights reserved.