Effect of temperature on the shear strength of aluminium single lap bonded joints for high temperature applications

An experimental and numerical investigation into the shear strength behaviour of adhesive single lap joints (SLJs) was carried out in order to understand the effect of temperature on the joint strength. The adherend material used for the experimental tests was an aluminium alloy in the form of thin sheets, and the adhesive used was a high-strength high temperature epoxy. Tensile tests as a function of temperature were performed and numerical predictions based on the use of a bilinear cohesive damage model were obtained. It is shown that at temperatures below Tg, the lap shear strength of SLJs increased, while at temperatures above Tg, a drastic drop in the lap shear strength was observed. Comparison between the experimental and numerical maximum loads representing the strength of the joints shows a reasonably good agreement.

Numerical and Experimental Analysis of Balanced and Unbalanced Adhesive Single-Lap Joints between Aluminium Adherends

The single-lap joint is the most commonly used, although it endures significant bending due to the non-collinear load path, which negatively affects its load bearing capabilities. The use of material or geometric changes is widely documented in the literature to reduce this handicap, acting by reduction of peel and shear peak stresses or alterations of the failure mechanism emerging from local modifications. In this work, the effect of using different thickness adherends on the tensile strength of single-lap joints, bonded with a ductile and brittle adhesive, was numerically and experimentally evaluated. The joints were tested under tension for different combinations of adherend thickness. The effect of the adherends thickness mismatch on the stress distributions was also investigated by Finite Elements (FE), which explained the experimental results and the strength prediction of the joints. The numerical study was made by FE and Cohesive Zone Modelling (CZM), which allowed characterizing the entire fracture process. For this purpose, a FE analysis was performed in ABAQUS® considering geometric non-linearities. In the end, a detailed comparative evaluation of unbalanced joints, commonly used in engineering applications, is presented to give an understanding on how modifications in the bonded structures thickness can influence the joint performance.

Visible range plasmonic effect produced by aluminium nanoparticles embedded in amorphous silicon

We present results, obtained by means of an analytic study and a numerical simulation, about the resonant condition necessary to produce a Localized Surface Plasmonic Resonance (LSPR) effect at the surface of metal nanospheres embedded in an amorphous silicon matrix. The study is based on a Lorentz dispersive model for a-Si:H permittivity and a Drude model for the metals. Considering the absorption spectra of a-Si:H, the best choice for the metal nanoparticles appears to be aluminium, indium or magnesium. No difference has been observed when considering a-SiC:H. Finite-difference time-domain (FDTD) simulation of an Al nanosphere embedded into an amorphous silicon matrix shows an increased scattering radius and the presence of LSPR induced by the metal/semiconductor interaction under green light (560 nm) illumination. Further results include the effect of the nanoparticles shape (nano-ellipsoids) in controlling the wavelength suitable to produce LSPR. It has been shown that is possible to produce LSPR in the red part of the visible spectrum (the most critical for a-Si:H solar cells applications in terms of light absorption enhancement) with aluminium nano-ellipsoids. As an additional results we may conclude that the double Lorentz-Lorenz model for the optical functions of a-Si:H is numerically stable in 3D simulations and can be used safely in the FDTD algorithm. A further simulation study is directed to determine an optimal spatial distribution of Al nanoparticles, with variable shapes, capable to enhance light absorption in the red part of the visible spectrum, exploiting light trapping and plasmonic effects. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Historically accurate reconstructions and characterisation of chrome yellow pigments

Dissertation presented at the Faculty of Sciences and Technology of the New University of Lisbon in fulfillment of the requirements for the Master degree in Conservation Science

Metals in proteins from sulphate-reducing bacteria: adenylate kinase and ATP sulfurylase. Proteins containing cobalt, zinc, iron (II) ions

A Thesis submitted at the Faculty Science and Technology of the New University of Lisbon for a degree in Doctor of Philosophy in Biochemistry with specialization in Physical Biochemistry

Staining of intestinal protozoa with heidenhain's iron Hematoxylin

Due to its unique properties, iron hematoxylin has been traditionally recommended for staining intestinal protozoa. This process can be simplified by reducing the number of steps and periods of permanence of the slides in some of the liquids used, without detriment to the quality of the results. Thus iron hematoxylin becomes adequate for routine use. Hematoxylin is a natural dye extracted from Haematoxylon campechianum, of the family Leguminosae. It must first be 'ripened', i.e. oxidized to hematein, which reacts with ferric ammonium sulphate to produce the ferric lake (iron hematoxylin), a basic dye. Iron hematoxylin most frequently stains regressively, i.e. the slides are first overstained and then differentiated.

Strength improvement of adhesively-bonded scarf repairs in aluminium structures with external reinforcements

Adhesively bonded techniques are an attractive option to repair aluminium structures, compared to more traditional methods. Actually, as a result of the improvement in the mechanical characteristics of adhesives, adhesive bonding has progressively replaced the traditional joining methods. There are several bonded repair configurations, as single-strap, double-strap and scarf. Compared with strap repairs, scarf repairs have the advantages of a higher efficiency and the absence of aerodynamic disturbance. The higher efficiency is caused by the elimination of the significant joint eccentricities of strap repairs. Moreover, stress distributions along the bond length are more uniform, due to tapering of the scarf edges. The main disadvantages of this technique are the difficult machining of the surfaces, associated costs and requirement of specialised labour. This work reports on an experimental and numerical study of the tensile behaviour of two-dimensional (2D) scarf repairs of aluminium structures bonded with the ductile epoxy adhesive Araldite® 2015. The numerical analysis, by Finite Elements (FE), was performed in Abaqus® and used cohesive zone models (CZM) for the simulation of damage onset and growth in the adhesive layer, thus enabling the strength prediction of the repairs. A parametric study was performed on the scarf angle (α) and different configurations of external reinforcement (applied on one or two sides of the repair, and also different reinforcement lengths). The obtained results allowed the establishment of design guidelines for repairing, showing that the use of external reinforcements enables increasing α for equal strength recovery, which makes the repair procedure easier. The numerical technique was accurate in predicting the repairs’ strength, enabling its use for design and optimisation purposes.

Speech as the basic interface for assistive technology

Speech interfaces for Assistive Technologies are not common and are usually replaced by others. The market they are targeting is not considered attractive and speech technologies are still not well spread. Industry still thinks they present some performance risks, especially Speech Recognition systems. As speech is the most elemental and natural way for communication, it has strong potential for enhancing inclusion and quality of life for broader groups of users with special needs, such as people with cerebral palsy and elderly staying at their homes. This work is a position paper in which the authors argue for the need to make speech become the basic interface in assistive technologies. Among the main arguments, we can state: speech is the easiest way to interact with machines; there is a growing market for embedded speech in assistive technologies, since the number of disabled and elderly people is expanding; speech technology is already mature to be used but needs adaptation to people with special needs; there is still a lot of R&D to be done in this area, especially when thinking about the Portuguese market. The main challenges are presented and future directions are proposed.

Development and implementation of strategies for the incorporation of reinforcing elements in aluminium alloys by solid state processing

Dissertação para obtenção do Grau de Mestre em Engenharia Mecânica

Factors associated to infection by Toxoplasma gondii in pregnant women attended in Basic Health Units in the city of Rolândia, Paraná, Brazil

The aim of the present work was to determine the prevalence of IgG and IgM anti-Toxoplasma gondii antibodies and the factors associated to the infection in pregnant women attended in Basic Health Units in Rolândia, Paraná, Brazil. The sample was divided in two groups: group I (320 pregnant women who were analyzed from July 2007 to February 2008) and group II (287 pregnant women who were analyzed from March to October 2008). In group I, it was found 53.1% of pregnant women with IgG reactive and IgM non-reactive, 1.9% with IgG and IgM reactive, 0.3% with IgG non-reactive and IgM reactive and 44.7% with IgG and IgM non-reactive. In group II, it was found 55.1% with IgG reactive and IgM non-reactive and 44.9% with IgG and IgM non-reactive. The variables associated to the presence of IgG antibodies were: residence in rural areas, pregnant women between 35-40 years old, low educational level, low family income, more than one pregnancy, drinking water which does not originate from the public water supply system and the habit of handling soil or sand. Guidance on primary prevention measures and the quarterly serological monitoring of the pregnant women in the risk group are important measures to prevent congenital toxoplasmosis.

Strength and damage analysis of composite-aluminium adhesively-bonded single-lap joints

With the need to find an alternative way to mechanical and welding joints, and at the same time to overcome some limitations linked to these traditional techniques, adhesive bonds can be used. Adhesive bonding is a permanent joining process that uses an adhesive to bond the components of a structure. Composite materials reinforced with fibres are becoming increasingly popular in many applications as a result of a number of competitive advantages. In the manufacture of composite structures, although the fabrication techniques reduce to the minimum by means of advanced manufacturing techniques, the use of connections is still required due to the typical size limitations and design, technological and logistical aspects. Moreover, it is known that in many high performance structures, unions between composite materials with other light metals such as aluminium are required, for purposes of structural optimization. This work deals with the experimental and numerical study of single lap joints (SLJ), bonded with a brittle (Nagase Chemtex Denatite XNRH6823) and a ductile adhesive (Nagase Chemtex Denatite XNR6852). These are applied to hybrid joints between aluminium (AL6082-T651) and carbon fibre reinforced plastic (CFRP; Texipreg HS 160 RM) adherends in joints with different overlap lengths (LO) under a tensile loading. The Finite Element (FE) Method is used to perform detailed stress and damage analyses allowing to explain the joints’ behaviour and the use of cohesive zone models (CZM) enables predicting the joint strength and creating a simple and rapid design methodology. The use of numerical methods to simulate the behaviour of the joints can lead to savings of time and resources by optimizing the geometry and material parameters of the joints. The joints’ strength and failure modes were highly dependent on the adhesive, and this behaviour was successfully modelled numerically. Using a brittle adhesive resulted in a negligible maximum load (Pm) improvement with LO. The joints bonded with the ductile adhesive showed a nearly linear improvement of Pm with LO.

Friction surfacing of aluminium alloys

Dissertação para a obtenção do grau de Mestre em Engenharia Mecânica

Production of aluminium based composites reinforced with embedded NiTi by friction stir welding

Dissertação para a obtenção do grau de Mestre em Engenharia Mecânica

The influence of the regional basic diet from northeast Brazil on health and nutritional conditions of mice infected with Schistosoma mansoni

Protein nutritionalstatus indicators were studied in weanling albino Swiss mice infected with S. mansoni andfed the Regional Basic Diet (RBD)from Northeast Brazil, a multideficient diet of low-protein content. Each mouse was infected percutaneously with 80 cercariae. The experiment lasted 63 days. The growth curve, food consumption, protein intake, weight gain, Protein Efficiency Ratio (PER) and Net Protein Ratio (NPR) were the parameters investigated. RBD-fed mice showed a marked weight loss, a lower food and protein intake, a slower body weight gain and lower rates of food protein utilization when compared to casein-fed animals. Differences between infected and non-infected mice were not consistent. The present results suggest that the effects of RBD-induced malnutrition on health and nutritional conditions of the mice are more severe than those of Manson's schistosomiasis, in the initial phase of the disease.

Re-evaluation of the basic procedures involved in the storage of measles vaccine in public health units of the municipality of Niterói, state of Rio de Janeiro, Brazil

Four years after the first visit seventeen public health units were visited again and evaluated as to standards of storage recommended by the Brazilian Immunization Programme. In 100% of the units, refrigerators and proper inside location of vaccines in the refrigerator were adequatety or regularfy maintained and checked, respectively. However, when control of temperature was checked, onfy 64.7% presented adequate storage conditions. In 94.1 % of the units, health workers complained of lack of immediate technical support in emergency situations. In 55.2 % the titers vaccine samples of were under the minimal recommended potency. It is necessary that the factors concerning the cold chain be continualfy evaluated so that the quality of the vaccines that will be used is not affected.