Distribution of benthos in late Quaternary turbidite layers of sediment cores from the North-West African continental margin

The CaCO3-contents and the fractions > 40 µm have been analysed from 5 kastenloten, one piston core and two kastengreifer taken between Senegal and Cape Verde Islands. Numerous benthonic and planktonic organisms and different terrigenous components have been distinguished. The four cores off Senegal reach middle Wuerm sediments; cores GIK12329-6 and TAG72-1 reach the V-zone and core GIK12331-4 the X-zone (Eem); the two kastengreifer contain sediments of Holocene age. Correlation of the cores has been made. Holocene sedimentation rates decrease from the shallow cores (6-11 cm/1000 years) to the deep-sea (1-2 cm/1000 years). The following climatic variations could be deduced from the sediments off the Senegal: during Holocene climate was in general as today, the Senegal river transporting fine grained material to the sea. The upper Wuerm was arid with no river influence but with red dune sand transported to the continental slope. During middle Wuerm the climate was humid again. The deep-sea cores have been influenced by eolian material from arid regions during glacial and interglacial periods, indicated by relatively high "Wuestenquarz-numbers". However, during Wuerm "Wuestenquarz-numbers" are higher than during Holocene and Eem, indicating that more intensely red coloured sediment was exposed to wind activity on the continent during this period. Varying amounts of terrigenous material and CaCO3-contents indicate varying wind strengths (lower in Holocene and Eem than during Wuerm). The boundary between humid and arid Wuerm climate was at approximately 20 °N. Influence of upwelling is difficult to establish in the sediments off Senegal, because river influence, while increasing fertility also dilutes the diatoms which are typical for upwelling. High amounts of organic carbon, low plankton/benthos ratios of foraminifers and low plankton foraminifer/radiolarian ratios in Holocene sections might be interpreted as influenced by upwelling. Turbidites occur in cores 72 and 31 and at the Holocene/Pleistocene boundary of core GIK12329-6. Their composition indicates provenance from the continental shelf of the Cape Verde Islands for core 31 and the continental shelf and slope off Senegal for core TAG72-1. Volcanic material, rare in the normal pelagic sediment of core GIK12331-4 is more frequent in the turbidites.

Pollen records from two outcrop profiles in the Kakitu Mountain of Tibet

There is a great similarity between pollen types which occur in the early Holocene NE Tibetan pollen spectra and those which are commonly considered to be typical for the Würm Late Glacial period in Central Europe and for the Würm Pleniglacial period in Southern Europe. Evidently, this similarity is due to a remarkable general conformity of plant taxa growing in cold-arid regions of the northern hemisphere. The improvement of the climate and the retreat of the glaciers that commenced at the end of the Würm period had already terminated definitely before 9500 BP. In addition, the climatic situation as well as the vegetation belts must have remained rather constant during the following 3000 yr, i.e. through most parts of the climatic optimum of the Holocene.

Pollen record and calculated holocene vegetation and climate dynamics from Sihailongwan Maar Lake, NE China

High-resolution palynological analysis on annually laminated sediments of Sihailongwan Maar Lake (SHL) provides new insights into the Holocene vegetation and climate dynamics of NE China. The robust chronology of the presented record is based on varve counting and AMS radiocarbon dates from terrestrial plant macro-remains. In addition to the qualitative interpretation of the pollen data, we provide quantitative reconstructions of vegetation and climate based on the method of biomization and weighted averaging partial least squares regression (WA-PLS) technique, respectively. Power spectra were computed to investigate the frequency domain distribution of proxy signals and potential natural periodicities. Pollen assemblages, pollen-derived biome scores and climate variables as well as the cyclicity pattern indicate that NE China experienced significant changes in temperature and moisture conditions during the Holocene. Within the earliest phase of the Holocene, a large-scale reorganization of vegetation occurred, reflecting the reconstructed shift towards higher temperatures and precipitation values and the initial Holocene strengthening and northward expansion of the East Asian summer monsoon (EASM). Afterwards, summer temperatures remain at a high level, whereas the reconstructed precipitation shows an increasing trend until approximately 4000 cal. yr BP. Since 3500 cal. yr BP, temperature and precipitation values decline, indicating moderate cooling and weakening of the EASM. A distinct periodicity of 550-600 years and evidence of a Mid-Holocene transition from a temperature-triggered to a predominantly moisture-triggered climate regime are derived from the power spectra analysis. The results obtained from SHL are largely consistent with other palaeoenvironmental records from NE China, substantiating the regional nature of the reconstructed vegetation and climate patterns. However, the reconstructed climate changes contrast with the moisture evolution recorded in S China and the mid-latitude (semi-)arid regions of N China. Whereas a clear insolation-related trend of monsoon intensity over the Holocene is lacking from the SHL record, variations in the coupled atmosphere-Pacific Ocean system can largely explain the reconstructed changes in NE China.

Revised calibration of the MBT-CBT paleotemperature proxy

The MBT-CBT proxy for the reconstruction of paleotemperatures and past soil pH is based on the distribution of branched glycerol dialkyl glycerol tetraether (brGDGT) membrane lipids. The Methylation of Branched Tetraether (MBT) and the Cyclisation of Branched Tetraether (CBT) indices were developed to quantify these distributions, and significant empirical relations between these indices and annual mean air temperature (MAT) and/or soil pH were found in a large data set of soils. In this study, we extended this soil dataset to 278 globally distributed surface soils. Of these soils, 26% contains all nine brGDGTs, while in 63% of the soils the seven most common brGDGTs were detected, and the latter were selected for calibration purposes. This resulted in new transfer functions for the reconstruction of pH based on the CBT index: pH = 7.90-1.97 × CBT (r**2 = 0.70; RMSE = 0.8; n = 176), as well as for MAT based on the CBT index and methylation index based on the seven most abundant GDGTs (defined as MBT'): MAT = 0.81-5.67 × CBT + 31.0 × MBT' (r**2 = 0.59; RMSE = 5.0 °C; n = 176). The new transfer function for MAT has a substantially lower correlation coefficient than the original equation (r**2 = 0.77). To investigate possible improvement of the correlation, we used our extended global surface soil dataset to statistically derive the indices that best describe the relations of brGDGT composition with MAT and soil pH. These new indices, however, resulted in only a relatively minor increase in correlation coefficients, while they cannot be explained straightforwardly by physiological mechanisms. The large scatter in the calibration cannot be fully explained by local factors or by seasonality, but MAT for soils from arid regions are generally substantially (up to 20 °C) underestimated, suggesting that absolute brGDGT-based temperature records for these areas should be interpreted with caution. The applicability of the new MBT'-CBT calibration function was tested using previously published MBT-CBT-derived paleotemperature records covering the last deglaciation in Central Africa and East Asia, the Eocene-Oligocene boundary and the Paleocene-Eocene thermal maximum. The results show that trends remain similar in all records, but that absolute temperature estimates and the amplitude of temperature changes are lower for most records, and generally in better agreement with independent proxy data.

Integrated economic-hydrologic analysis of policy responses

Water is a vital resource, but also a critical limiting factor for economic and social development in many parts of the world. The recent rapid growth in human population and water use for social and economic development is increasing the pressure on water resources and the environment, as well as leading to growing conflicts among competing water use sectors (agriculture, urban, tourism, industry) and regions (Gleick et al., 2009; World Bank, 2006). In Spain, as in many other arid and semi-arid regions affected by drought and wide climate variability, irrigated agriculture is responsible for most consumptive water use and plays an important role in sustaining rural livelihoods (Varela-Ortega, 2007). Historically, the evolution of irrigation has been based on publicly-funded irrigation development plans that promoted economic growth and improved the socio-economic conditions of rural farmers in agrarian Spain, but increased environmental damage and led to excessive and inefficient exploitation of water resources (Garrido and Llamas, 2010; Varela-Ortega et al., 2010). Currently, water policies in Spain focus on rehabilitating and improving the efficiency of irrigation systems, and are moving from technocratic towards integrated water management strategies driven by the European Union (EU) Water Framework Directive (WFD).

An economic modelling approach for vulnerability assesment in irrigation farms in Spain

In the last years, vulnerability assessment has emerged as a need for policy making instead of being a pure academic exercise (Hinkel, 2010). In the current context of changing climate, increasing water scarcity threatens economic activities in many arid or semi-arid regions of the World. Climate change (CC) science and policy debates have traditionally focused on CC mitigation and impact assessment (Krysanova et al., 2010). However, even if mitigation policies are successfully enforced some climate change is still expected. Then, adaptation is strongly necessary and, for that, improved knowledge on vulnerability and adaptive capacity is required.

Effect of integrated reservoir tillage for in-situ rainwater harvesting and other tillage practices on soil physical properties

There is a need for in-situ soil moisture conservation in arid and semi-arid regions due to insufficient rainfall for agriculture. For this purpose, a combination implement [integrated reservoir tillage system (RT)] comprised of a single-row chisel plow, single-row spike tooth harrow, modified seeder, and spiked roller was developed and compared to the popular tillage practices, viz., minimum tillage (MT) and conventional tillage (CT) in an arid Mediterranean environment in Egypt. The different tillage practices were conducted at tillage depths of 15, 20, and 25 cm and forward speeds of 0.69, 1, 1.25, and 1.53 m s-1. Some soil physical properties, runoff, soil loss, water harvesting efficiency and yield of wheat were evaluated. The different tillage practices caused significant differences in soil physical properties as the RT increased soil infiltration, producing a rate of 48% and 65% higher than that obtained in MT and CT, respectively. The lowest values of runoff and soil loss were recorded under RT as 4.91 mm and 0.65 t ha-1, whereas the highest values were recorded under CT as 11.36 mm and 1.66 t ha-1, respectively. In conclusion, the RT enhanced the infiltration rate, increased water harvesting efficiency, reduced runoff and achieved the highest yield of wheat. The best tillage operating parameters appeared to be at a tillage depth of 20 cm and speed between 1.00 and 1.25 m s-1.

Selecting crop models for decision making in wheat insurance

In crop insurance, the accuracy with which the insurer quantifies the actual risk is highly dependent on the availability on actual yield data. Crop models might be valuable tools to generate data on expected yields for risk assessment when no historical records are available. However, selecting a crop model for a specific objective, location and implementation scale is a difficult task. A look inside the different crop and soil modules to understand how outputs are obtained might facilitate model choice. The objectives of this paper were (i) to assess the usefulness of crop models to be used within a crop insurance analysis and design and (ii) to select the most suitable crop model for drought risk assessment in semi-arid regions in Spain. For that purpose first, a pre-selection of crop models simulating wheat yield under rainfed growing conditions at the field scale was made, and second, four selected models (Aquacrop, CERES- Wheat, CropSyst and WOFOST) were compared in terms of modelling approaches, process descriptions and model outputs. Outputs of the four models for the simulation of winter wheat growth are comparable when water is not limiting, but differences are larger when simulating yields under rainfed conditions. These differences in rainfed yields are mainly related to the dissimilar simulated soil water availability and the assumed linkages with dry matter formation. We concluded that for the simulation of winter wheat growth at field scale in such semi-arid conditions, CERES-Wheat and CropSyst are preferred. WOFOST is a satisfactory compromise between data availability and complexity when detail data on soil is limited. Aquacrop integrates physiological processes in some representative parameters, thus diminishing the number of input parameters, what is seen as an advantage when observed data is scarce. However, the high sensitivity of this model to low water availability limits its use in the region considered. Contrary to the use of ensembles of crop models, we endorse that efforts be concentrated on selecting or rebuilding a model that includes approaches that better describe the agronomic conditions of the regions in which they will be applied. The use of such complex methodologies as crop models is associated with numerous sources of uncertainty, although these models are the best tools available to get insight in these complex agronomic systems.

Aeolian dust in Colorado Plateau soils: Nutrient inputs and recent change in source

Aeolian dust (windblown silt and clay) is an important component in arid-land ecosystems because it may contribute to soil formation and furnish essential nutrients. Few geologic surfaces, however, have been characterized with respect to dust-accumulation history and resultant nutrient enrichment. We have developed a combination of methods to identify the presence of aeolian dust in arid regions and to evaluate the roles of this dust in ecosystem processes. Unconsolidated sandy sediment on isolated surfaces in the Canyonlands region of the Colorado Plateau differs greatly in mineralogical and chemical composition from associated bedrock, mainly aeolian sandstone. Detrital magnetite in the surficial deposits produces moderately high values of magnetic susceptibility, but magnetite is absent in nearby bedrock. A component of the surficial deposits must be aeolian to account for the abundance of magnetite, which formed originally in far-distant igneous rocks. Particle-size analysis suggests that the aeolian dust component is typically as much as 20–30%. Dust inputs have enriched the sediments in many elements, including P, Mg, Na, K, and Mo, as well as Ca, at sites where bedrock lacks calcite cement. Soil-surface biologic crusts are effective dust traps that apparently record a change in dust sources over the past several decades. Some of the recently fallen dust may result from human disturbance of land surfaces that are far from the Canyonlands, such as the Mojave Desert. Some land-use practices in the study area have the potential to deplete soil fertility by means of wind-erosion removal of aeolian silt.

Comparison among monitoring strategies to assess water flow dynamic and soil hydraulic properties in agricultural soils

Irrigated agriculture is usually performed in semi-arid regions despite scarcity of water resources. Therefore, optimal irrigation management by monitoring the soil is essential, and assessing soil hydraulic properties and water flow dynamics is presented as a first measure. For this purpose, the control of volumetric water content, θ, and pressure head, h, is required. This study adopted two types of monitoring strategies in the same experimental plot to control θ and h in the vadose zone: i) non-automatic and more time-consuming; ii) automatic connected to a datalogger. Water flux was modelled with Hydrus-1D using the data collected from both acquisition strategies independently (3820 daily values for the automatic; less than 1000 for the non-automatic). Goodness-of-fit results reported a better adjustment in case of automatic sensors. Both model outputs adequately predicted the general trend of θ and h, but with slight differences in computed annual drainage (711 mm and 774 mm). Soil hydraulic properties were inversely estimated from both data acquisition systems. Major differences were obtained in the saturated volumetric water content, θs, and the n and α van Genuchten model shape parameters. Saturated hydraulic conductivity, Ks, shown lower variability with a coefficient of variation range from 0.13 to 0.24 for the soil layers defined. Soil hydraulic properties were better assessed through automatic data acquisition as data variability was lower and accuracy was higher.

Detailing for a research centre in Antarctica: An experiment to force students to be creative instead of copying standard solutions

In order to equip architecture students with ambitious detail designing ability, related courses of the architecture programs should deal with subjects which are rather rare and unusual for real life practices in order to prevent students copying standard details. In 2015 an innovative project brief has been given to architecture students of Istanbul Technical University. The scenario given in the brief is to design a research station for the first group of Turkish scientist, to be built in one of the coldest and most arid regions on earth; the Antarctica. The performance requirements given in the brief were determined to prevent the students from copying details from any kind of resources as the total number of details generated in real life for those conditions are very limited and specific. The method used has demonstrated a great success and creative detail solutions were generated by the students. In the paper, the innovative coursework brief for bettering the detail design ability of architecture students is explained and the output of the studio is presented.

Water harvesting by catchments /

Mode of access: Internet.

Evolution of plant water relations research in Australia

Ecophysiological research in Australia has focussed, at different times, on the fundamental similarities in function between all plant species, and on the peculiarity of Australian species with respect to their survival in stressful environments. Early work on plant water relations emphasised the differences between species, and indicated that diverse structural and functional attributes occurred in species from the same water-limited environment. Most recent research has emphasised processes that optimise rates of carbon dioxide exchange, but the understanding of functioning in plants with different morphological arrangements is incomplete. Variation in functions between individual plants and geographic populations in wild species has been examined to a lesser extent. The great variety within and between populations of wild plant species warrants further study for both understanding and more effective management of this biological resource.

Ross River virus disease in Australia, 1886-1998, with analysis of risk factors associated with outbreaks

Ross River virus (RE) is a mosquito-borne arbovirus responsible for outbreaks of polyarthritic disease throughout Australia. To better understand human and environmental factors driving such events, 57 historical reports oil RR Outbreaks between 1896 and 1998 were examined collectively. The magnitude, regularity, seasonality, and locality of outbreaks were found to be wide ranging; however, analysis of climatic and tidal data highlighted that environmental conditions let differently ill tropical, arid, and temperate regions. Overall, rainfall seems to be the single most important risk factor, with over 90% of major outbreak locations receiving higher than average rainfall in preceding mouths. Many temperatures were close to average, particularly in tropical populations; however, in arid regions, below average maximum temperatures predominated, and ill southeast temperate regions, above average minimum temperatures predominated. High spring tides preceded coastal Outbreaks, both in the presence and absence of rainfall, and the relationship between rainfall and the Southern Oscillation Index and Lit Nina episodes suggest they may be useful predictive tools, but only ill southeast temperate regions. Such heterogeneity predisposing outbreaks supports the notion that there are different RE epidemiologies throughout Australia but also Suggests that generic parameters for the prediction and control of outbreaks are of limited use at a local level.

A solar-powered reverse osmosis system for high recovery of freshwater from saline groundwater

Desalination of groundwater is essential in arid regions that are remote from both seawater and freshwater resources. Desirable features of a groundwater desalination system include a high recovery ratio, operation from a sustainable energy source such as solar, and high water output per unit of energy and land. Here we propose a new system that uses a solar-Rankine cycle to drive reverse osmosis (RO). The working fluid such as steam is expanded against a power piston that actuates a pump piston which in turn pressurises the saline water thus passing it through RO membranes. A reciprocating crank mechanism is used to equalise the forces between the two pistons. The choice of batch mode in preference to continuous flow permits maximum energy recovery and minimal concentration polarisation in the vicinity of the RO membrane. This study analyses the sizing and efficiency of the crank mechanism, quantifies energy losses in the RO separation and predicts the overall performance. For example, a system using a field of linear Fresnel collectors occupying 1000 m2 of land and raising steam at 200 °C and 15.5 bar could desalinate 350 m3/day from saline water containing 5000 ppm of sodium chloride with a recovery ratio of 0.7.