Theoretical investigation of the use of a moving vehicle to identify bridge dynamic parameters

Pavements and bridges are subject to a continuous degradation due to traffic aggressiveness, ageing and environmental factors. A rational transport policy requires the monitoring of this transport infrastructure in order to provide adequate maintenance and guarantee the required levels of transport service and safety. This paper investigates the use of an instrumented vehicle fitted with accelerometers on its axles to monitor the dynamics of bridges. A simplified quarter carbridge interaction model is used in theoretical simulations and the natural frequency of the bridge is extracted from the spectra of the vehicle accelerations. The accuracy is better at lower speeds and for smooth road profiles. The structural damping of the bridge was also monitored for smooth and rough road profiles. The magnitude of peaks in the power spectral density of the vehicle accelerations decreased with increasing bridge damping and this decrease was easier to detect the smoother the road profile.

An indirect bridge inspection method incorporating a wavelet-based damage indicator and pattern recognition

In recent years, there has been a move towards the development of indirect structural health monitoring (SHM)techniques for bridges; the low-cost vibration-based method presented in this paper is such an approach. It consists of the use of a moving vehicle fitted with accelerometers on its axles and incorporates wavelet analysis and statistical pattern recognition. The aim of the approach is to both detect and locate damage in bridges while reducing the need for direct instrumentation of the bridge. In theoretical simulations, a simplified vehicle-bridge interaction model is used to investigate the effectiveness of the approach in detecting damage in a bridge from vehicle accelerations. For this purpose, the accelerations are processed using a continuous wavelet transform as when the axle passes over a damaged section, any discontinuity in the signal would affect the wavelet coefficients. Based on these coefficients, a damage indicator is formulated which can distinguish between different damage levels. However, it is found to be difficult to quantify damage of varying levels when the vehicle’s transverse position is varied between bridge crossings. In a real bridge field experiment, damage was applied artificially to a steel truss bridge to test the effectiveness of the indirect approach in practice; for this purpose a two-axle van was driven across the bridge at constant speed. Both bridge and vehicle acceleration measurements were recorded. The dynamic properties of the test vehicle were identified initially via free vibration tests. It was found that the resulting damage indicators for the bridge and vehicle showed similar patterns, however, it was difficult to distinguish between different artificial damage scenarios.

Experimental validation of a drive-by stiffness identification method for bridge monitoring

An experimental investigation is carried out to verify the feasibility of using an instrumented vehicle to detect and monitor bridge dynamic parameters. The low-cost method consists of the use of a moving vehicle fitted with accelerometers on its axles. In the laboratory experiment, the vehicle–bridge interaction model consists of a scaled two-axle vehicle model crossing a simply supported steel beam. The bridge model also includes a scaled road surface profile. The effects of varying the vehicle model configuration and speed are investigated. A finite element beam model is calibrated using the experimental results, and a novel algorithm for the identification of global bridge stiffness is validated. Using measured vehicle accelerations as input to the algorithm, the beam stiffness is identified with a reasonable degree of accuracy.

Identification of Road Irregularities via Vehicle Accelerations

A periodic monitoring of the pavement condition facilitates a cost-effective distribution of the resources available for maintenance of the road infrastructure network. The task can be accurately carried out using profilometers, but such an approach is generally expensive. This paper presents a method to collect information on the road profile via accelerometers mounted in a fleet of non-specialist vehicles, such as police cars, that are in use for other purposes. It proposes an optimisation algorithm, based on Cross Entropy theory, to predict road irregularities. The Cross Entropy algorithm estimates the height of the road irregularities from vehicle accelerations at each point in time. To test the algorithm, the crossing of a half-car roll model is simulated over a range of road profiles to obtain accelerations of the vehicle sprung and unsprung masses. Then, the simulated vehicle accelerations are used as input in an iterative procedure that searches for the best solution to the inverse problem of finding road irregularities. In each iteration, a sample of road profiles is generated and an objective function defined as the sum of squares of differences between the ‘measured’ and predicted accelerations is minimized until convergence is reached. The reconstructed profile is classified according to ISO and IRI recommendations and compared to its original class. Results demonstrate that the approach is feasible and that a good estimate of the short-wavelength features of the road profile can be detected, despite the variability between the vehicles used to collect the data.

Detection of Bridge Dynamic Parameters using an Instrumented Vehicle

Highway structures such as bridges are subject to continuous degradation primarily due to ageing and environmental factors. A rational transport policy requires the monitoring of this transport infrastructure to provide adequate maintenance and guarantee the required levels of transport service and safety. In Europe, this is now a legal requirement - a European Directive requires all member states of the European Union to implement a Bridge Management System. However, the process is expensive, requiring the installation of sensing equipment and data acquisition electronics on the bridge. This paper investigates the use of an instrumented vehicle fitted with accelerometers on its axles to monitor the dynamic behaviour of bridges as an indicator of its structural condition. This approach eliminates the need for any on-site installation of measurement equipment. A simplified half-car vehicle-bridge interaction model is used in theoretical simulations to test the possibility of extracting the dynamic parameters of the bridge from the spectra of the vehicle accelerations. The effect of vehicle speed, vehicle mass and bridge span length on the detection of the bridge dynamic parameters are investigated. The algorithm is highly sensitive to the condition of the road profile and simulations are carried out for both smooth and rough profiles

Monitoring Bridge Dynamic Behaviour using an Instrumented Two Axle Vehicle

Highway structures such as bridges are subject to continuous degradation primarily due to ageing, loading and environmental factors. A rational transport policy must monitor and provide adequate maintenance to this infrastructure to guarantee the required levels of transport service and safety. Increasingly in recent years, bridges are being instrumented and monitored on an ongoing basis due to the implementation of Bridge Management Systems. This is very effective and provides a high level of protection to the public and early warning if the bridge becomes unsafe. However, the process can be expensive and time consuming, requiring the installation of sensors and data acquisition electronics on the bridge. This paper investigates the use of an instrumented 2-axle vehicle fitted with accelerometers to monitor the dynamic behaviour of a bridge network in a simple and cost-effective manner. A simplified half car-beam interaction model is used to simulate the passage of a vehicle over a bridge. This investigation involves the frequency domain analysis of the axle accelerations as the vehicle crosses the bridge. The spectrum of the acceleration record contains noise, vehicle, bridge and road frequency components. Therefore, the bridge dynamic behaviour is monitored in simulations for both smooth and rough road surfaces. The vehicle mass and axle spacing are varied in simulations along with bridge structural damping in order to analyse the sensitivity of the vehicle accelerations to a change in bridge properties. These vehicle accelerations can be obtained for different periods of time and serve as a useful tool to monitor the variation of bridge frequency and damping with time.

Using Instrumented Vehicles To Detect Damage in Bridges

Bridge structures are subject to continuous degradation due to the environment, ageing and excess loading. Monitoring of bridges is a key part of any maintenance strategy as it can give early warning if a bridge is becoming unsafe. This paper will theoretically assess the ability of a vehicle fitted with accelerometers on its axles to detect changes in damping of bridges, which may be the result of damage. Two vehicle models are used in this investigation. The first is a two degree-of-freedom quarter-car and the second is a four degree-of-freedom halfcar. The bridge is modelled as a simply supported beam and the interaction between the vehicle and the bridge is a coupled dynamic interaction algorithm. Both smooth and rough road profiles are used in the simulation and results indicate that changes in bridge damping can be detected by the vehicle models for a range of vehicle velocities and bridge spans.

Using Instrumented Vehicles to Detect Damage in Bridges

This paper describes a ‘drive-by’ method of bridge inspection using an instrumented vehicle. Accelerometers on the vehicle are proposed as a means of detecting damage on the bridge in the time it takes for the vehicle to cross the bridge at full highway speed. For a perfectly smooth road profile, the method is shown to be feasible. Changes in bridge damping, which is an indicator of damage, are clearly visible in the acceleration signal of a quarter-car vehicle on a smooth road surface modelled using MatLab. When road profile is considered, the influence of changes in bridge damping on the vehicle acceleration signal is much less clear. However, when a half-car model is used on a road with a rough profile, it is again possible to detect changes in bridge damping, provided the vehicle has two identical axles.

Dynamic axle force and road profile identification using a moving vehicle

The axle forces applied by a vehicle through its wheels are a critical part of the interaction between vehicles, pavements and bridges. Therefore, the minimisation of these forces is important in order to promote long pavement life spans and ensure that bridge loads are small. Moreover, as the road surface roughness affects the vehicle dynamic forces, the monitoring of pavements for highways and bridges is an important task. This paper presents a novel algorithm to identify these dynamic interaction forces which involves direct instrumentation of a vehicle with accelerometers. The ability of this approach to predict the pavement roughness is also presented. Moving force identification theory is applied to a vehicle model in theoretical simulations in order to obtain the interaction forces and pavement roughness from the measured accelerations. The method is tested for a range of bridge spans in simulations and the influence of road roughness level on the accuracy of the results is investigated. Finally, the challenge for the real-world problem is addressed in a laboratory experiment.

A Parametric Study of a Drive by Bridge Inspection System Based on the Morlet Wavelet

Many of the bridges currently in use worldwide are approaching the end of their design lives. However, rehabilitating and extending the lives of these structures raises important safety issues. There is also a need for increased monitoring which has considerable cost implications for bridge management systems. Existing structural health monitoring (SHM) techniques include vibration-based approaches which typically involve direct instrumentation of the bridge and are important as they can indicate the deterioration of the bridge condition. However, they can be labour intensive and expensive. In the past decade, alternative indirect vibration-based approaches which utilise the response of a vehicle passing over a bridge have been developed. This paper investigates such an approach; a low-cost approach for the monitoring of bridge structures which consists of the use of a vehicle fitted with accelerometers on its axles. The approach aims to detect damage in the bridge while obviating the need for direct instrumentation of the bridge. Here, the effectiveness of the approach in detecting damage in a bridge is investigated using a simplified vehicle-bridge interaction (VBI) model in theoretical simulations and a scaled VBI model in a laboratory experiment. In order to identify the existence and location of damage, the vehicle accelerations are recorded and processed using a continuous Morlet wavelet transform and a damage index is established. A parametric study is carried out to investigate the effect of parameters such as the bridge span length, vehicle speed, vehicle mass, damage level and road surface roughness on the accuracy of results.

A wavelet based drive-by bridge inspection system

This paper investigates a low-cost wavelet-based approach for the preliminary monitoring of bridge structures, consisting of the use of a vehicle fitted with accelerometers on its axles. The approach aims to reduce the need for direct instrumentation of the bridge. A time-frequency analysis is carried out in order to identify the existence and location of damage from vehicle accelerations. Firstly, in theoretical simulations, a simplified vehicle-bridge interaction model is used to investigate the effectiveness of the approach. A number of damage indicators are evaluated and compared. A range of parameters such as the bridge span, vehicle speed, damage level and location, signal noise and road roughness are varied in simulations. Secondly, a scaled laboratory experiment is carried out to validate the results of the theoretical analysis and assess the ability of the selected damage indicators to detect changes in the bridge response from vehicle accelerations. 

Sensores ópticos para monitorização dinâmica de estruturas

O presente trabalho centra-se no desenvolvimento e aplicação de sensores de aceleração ópticos, baseados em redes de Bragg gravadas em fibras ópticas, para monitorização da integridade estrutural de estruturas de engenharia civil. Foram implementados dois acelerómetros uniaxiais e um acelerómetro biaxial. Recorreu-se a uma ferramenta de simulação baseada no método dos elementos finitos que permitiu optimizar, sem custos de produção, as características dos sensores, nomeadamente a sua frequência de ressonância. A caracterização dos sensores foi realizada em ambiente laboratorial e a sua resposta comparada com os resultados de simulação, de modo a validar os modelos numéricos. A aplicabilidade e demonstração de conceito foram realizadas na monitorização de estruturas com testes de campo. Foi monitorizado um teste destrutivo de uma parede de adobe, construída à escala real no Departamento de Engenharia Civil da Universidade de Aveiro, onde foram utilizados sensores estáticos e dinâmicos baseados em redes de Bragg gravadas em fibra óptica. Foram realizadas medidas dinâmicas na ponte pedonal do Campus Universitário da Universidade de Aveiro, onde se compararam os resultados obtidos com os sensores ópticos com resultados de sensores electrónicos comerciais. O acelerómetro biaxial foi testado na monitorização de estruturas esbeltas, nomeadamente na monitorização de duas torres de telecomunicações móveis, onde se demonstrou a possibilidade da utilização de sensores ópticos na caracterização dinâmica deste tipo de estruturas. Outro tipo de estruturas de engenharia civil onde foi demonstrada a aplicabilidade dos sensores ópticos desenvolvidos na monitorização estrutural foram os reservatórios de água elevados. Foi realizada a monitorização dinâmica de um exemplo deste tipo de estruturas, localizado no Campus Universitário da Universidade de Aveiro. A monitorização foi realizada recorrendo ao sensor biaxial desenvolvido e a um sismógrafo, ficando o sensor óptico instalado na estrutura de modo a permitir futuras leituras e assim a monitorização periódica da estrutura. Foi ainda desenvolvido um sensor de humidade relativa do ar, com um material sol-gel, que permitiu registar o nível de humidade relativa no interior de blocos de betão, durante um ano. Este sensor pode ser incluído numa rede de sensores multiplexados, na caracterização e monitorização da integridade estrutural de certas estruturas de engenharia civil.

Demographic, Physical, and Behavioral Characteristics Associated with TV Parenting Practices Among Latino Parents of Preschool Children

Thesis (Master's)--University of Washington, 2015

A repeated measures experiment of school playing environment to increase physical activity and enhance self esteem in UK school children

School playtime provides daily opportunities for children to be active outdoors, but only makes small contributions to physical activity (PA) requirements. Natural environments facilitate unstructured PA and children report a preference for play in nature. Thus, play on the school field might encourage children to be more active during playtime. The primary aim of this study was to examine the impact of the school playing environment on children's PA. Descriptive data and fitness were assessed in 25 children aged 8–9 years from a single primary school. Over two consecutive weeks participants were allocated to either play on the school field or playground during playtime. The order of play in the two areas was randomised and counterbalanced. Moderate to vigorous PA (MVPA) was assessed during playtime on the last two days of each week using accelerometers. There was a significant interaction of environment and sex on MVPA during morning play (F(1,22) = 6.27; P<0.05; np2 = 0.222), but not during lunch (P>0.05; np2 = 0.060) or all of playtime combined (P>0.05; np2 = 0.140). During morning play boys were significantly more active than girls on the playground (t(23) = 1.32; P<0.01; n2 = 0.291), but not on the field (P>0.05; n2 = 0.071). For lunch (F(1,22) = 24,11; P<0.001; np2 = 0.523) and all of playtime combined (F(1,22) = 33.67; P<0.001; np2 = 0.616) there was a significant effect of environment. There was also a significant main effect of sex during lunch (F(1,22) = 11.56; P<0.01; np2 = 0.344) and all of playtime combined (F(1,22) = 12.37; P<0.01; np2 = 0.371). MVPA was higher on the field and boys were more active than girls. Play on the field leads to increases in MVPA, particularly in girls. The promising trend for the effect of the natural environment on MVPA indicates that interventions aimed at increasing MVPA should use the natural environment and that schools should encourage greater use of their natural areas to increase PA.

The effect of playground and nature-based interventions on physical activity and self-esteem in UK school children

School playtime provides opportunities for children to engage in physical activity (PA). Playground playtime interventions designed to increase PA have produced differing results. However, nature can also promote PA, through the provision of large open spaces for activity. The purpose of this study is to determine which playtime interventions are most effective at increasing moderate-to-vigorous physical activity (MVPA) and if this varies by school location. Fifty-two children from an urban and rural school participated in a playground sports (PS) and nature-based orienteering intervention during playtime for one week. MVPA was assessed the day before and on the final day of the interventions using accelerometers. Intervention type (p < 0.05) and school location (p < 0.001) significantly influenced MVPA; with PS increasing MVPA more than nature-based orienteering. Urban children seemed to respond to the interventions more positively; however, differences in baseline MVPA might influence these changes. There was a positive correlation for fitness and MVPA during PS (r = 0.32; p < 0.05), but not nature-based orienteering (p > 0.05). The provision of PS influences PA the most; however, a variety of interventions are required to engage less fit children in PA.