Pirólise termoquímica de pós da fibra de coco seco em um reator de cilindro rotativo para produção de bio-óleo

This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.

Use of Sludge as Ceramic Materials

Nowadays, with increase amounts of sludge derived from the treatment of domestic sewage put pressure into research on systems for the adequate use of these materials. The aim of the present work is to study the use of sludge ash, from sintering and calcinated process, as a raw material for the ceramic industry. Using the sewage sludge ashes as ceramic raw material there will be no contamination of soil and underground water. Metals and toxic compounds like Al, Fe, Ba, Cr, Cu, Mn and Zn oxides were analyzed and characterized by X-ray fluorescence (XRF), scanning electron microscopy (SEM) and plasma emission spectroscopy (ICP-OES). The leached material was chemically analyzed where the integration of oxides into the ceramic matrix of sludge ash was observed. Residual decomposition was analyzed by TG, DTG and DTA curves.

Cultivo de Ankistrodesmus gracilis (Reisch) Korsikov (Chlorophyta) em laboratório utilizando meio CHU12 e de macrófita com NPK

Two different culture media, namely CHU12 and inorganic fertilizer NPK (20-5-20) associated with macrophyte (Eichhornia crassipes) extract, were used to evaluate the development of A. gracilis. Growth rate, development, nutritional value and medium water quality were analyzed. A. gracilis in macrophyte+NPK medium had mean cell density (333x10(5) cells/mL) higher than medium CHU12 (302x10(5) cells/mL). Protein rate (12.52% PS), dry weight (397x10(7) pg/cell) and ashes (4.08x10(7) pg/cell) in A. gracilis was higher (p<0.05) than medium macrophyte+NPK. on the other hand, lipids, carbohydrates and fibers had the same rate (p>0.05) in both media. When hydrological variables in the culture medium of A. gracilis are taken into account, dissolved oxygen and free CO2 alone failed to have any significant difference (p>0.05) between the media employed. A. gracilis in the macrophyte+NPK medium had the same nutritional rate as the commercial medium CHU12, with excellent results for alga growth. Macrophyte medium may be used for large scale alga culture in the feed of fish larvae.

Growth and body nutrient deposition of two broiler commercial genetic lines

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação microbiológica e bromatológica da silagem ácida obtida de resíduos da indústria de filetagem de tilápia do Nilo (Oreochromis niloticus)

The experiment constituted in evaluating the acid silage prepared from Nile tilapia (Oreochromis niloticus) filletage industry residues. This silage was prepared in a filetage industry through the residues milling and 5% of ascetic acid addition and stock piling in a period up to until 201 days. Storaged silages in a period of 7, 12, 22, 27, 41, 48, 61, 75, 84, 91, 96, 110, 140, 151, 181, 187 and 201dias were evaluated. Bromatologics analyses of rude protein(PB), etereal extract (EE), humidity (UM), ashes (CZ) and microbiological analyses of Salmonella, total coliforms, faecals and Escherichia coli of the storaged silages in a period of 7, 91 and 201 days were realized. The pH was evaluated in all the storaged periods. Differences (P > 0.05) in the substance of PB, EE, UM and CZ were not observed. A linear increase in PH was observed, being stabilizing in plateau of 4.74. In relation to the microbiological analysis the presence of Salmonella, total coliforms, faecals and E. Coli were not found. Was concluded that the acid silage gotten from tilapia filetage residues produced with the use of 5% ascetic acid can be stored during 201 days without having Salmonella, total coliforms and faecals proliferation.

Características físico-qímicas da carne de caprinos submetidos a diferentes níveis de substituição do leite por soro de queijo durante o aleitamento

Fifty six crossbred kids Parda Alpina x Gurgueia were separeted into four groups of 14 (seven male and seven female) and submited to four treatments with different levels of milk goat substitution by cheese serum. The treatments were : T1=milk goat (testify); T2=15% serum at 23 days and 33% at 55 days; T3=15% serum starting from 16 days, 33% on 23 days and 51% on 72 days of age; and T4=33% on 16 days and 69% of liquid diet in the final fase. At 92 days of age, all animals were slaughtered for carcass evaluation. Pallete were separeted from 20 male animals (five by treatment) and the physical and chemical analysis of the meat were realized using these materials. The studied characteristics were: total weight (TW), meat weight (MW), bone weigth (BW) of the pallete, and percentage of umidity (U), ashes (A), protein (P), fat (F) and pH of the pallete meat. There was significant effect of the treatment over F. Means of PW, A and BW were, respectively 491, 342 and 149.8 g. The meal represented 69,6% of total pallete weight. Means of U, A, P and F were 73, 1.0, 19 and 1.95%, respectively. The pH was 6.7. Results allow to conclude that only the fat percentage of the meat was modified, due to the administration of serun milk on the liquid diet of the kids, during the milking fase.

Análise de Argamassas Com Substituição Parcial do Cimento Portland Por Cinza Residual de Lenha de Algaroba

With the increase in cement consumption, it has quickly become one of the inputs most consumed by mankind over the last century. This has caused an increase in CO2 emissions, as cement production releases large quantities of this gas into the atmosphere. Adding this fact to the growing consciousness of environmental preservation, it has led to a search for alternatives to cement to complement its derivatives, in the form of waste materials like the ashes. This research aimed to analyze the properties of mortars in fresh and hardened state with partial replacement of Portland cement by residual algaroba wood ash (CRLA) potteries produced by the state of Rio Grande do Norte. The CRLA was collected and sieved, where part of it was ground and characterized in comparison with that just sifted, being characterized according to its chemical composition, grain size, fineness, density, bulk density and index of pozzolanic activity. It was found that the wood ash does not act as pozzolan, and grinding it has not changed its characteristics compared to those just sifted, not justifying its use. Two traces were adopted for this research: 1:3 (cement: fine sand) and 1:2:8 (cement: hydrated lime: medium sand); both in volume, using as materials the CRLA just sifted, CP II F-32 Portland cement, CH-I hydrated lime, river sand and water from the local utility. For each trace were adopted six percentages of partial replacement of cement for wood ash: 0% (control) 5%, 7%, 10%, 12% and 15%. In the fresh state, the mortars were tested towards their consistency index and mass density. In the hardened state, they were tested towards their tensile strength in bending, compressive strength and tensile adhesion strength, and its mass density in the hardened state. The mortar was also analyzed by scanning electron microscopy and X-ray diffraction. Furthermore, it was classified according to NBR 13281 (2005). The results showed that up to a content of 5% substitution and for both traces, the residual algaroba wood ash can replace Portland cement without compromising the mortars microstructure and its fresh and hardened state

Rendimento de carcaça e composição química da carne da perdiz nativa (Rhynchotus rufescens)

A composição química da carne e o rendimento de carcaça de perdizes (Rhynchotus rufescens) adultas, com 12 meses, criadas em cativeiro com rações balanceadas, foram determinadas neste trabalho. Para rendimento de carcaça, após o abate e evisceração, foram feitos dois cortes: peito e coxa+sobrecoxa+dorso. Para análise química, foram retiradas três amostras de cada corte para determinação da composição centesimal da umidade, proteínas totais, lipídeos totais, cinzas e colesterol. Os valores observados mostraram um rendimento médio de carcaça de 74,4% com 36,6% de carne de peito. Os componentes químicos apresentaram para os cortes de coxa-sobrecoxa e peito, respectivamente, umidade 62,4 e 55,9%; proteínas 25,2 e 29,1%; lipídeos 1,6 e 5,6%; cinzas 1,4 e 1,2% e colesterol 234 e 70mg/100g. O excelente rendimento de carcaça, somado à composição química de sua carne, mostra o potencial desta espécie para a produção de carnes especiais.

Influência da interação fósforo disponível × fitase da dieta sobre o desempenho, os níveis plasmáticos de fósforo e os parâmetros ósseos de poedeiras comerciais

Dois experimentos foram realizados para avaliar a interação fósforo disponível (Pd) × fitase (UF) da dieta sobre o desempenho, os níveis plasmáticos de fósforo e os parâmetros ósseos de poedeiras. No experimento 1, utilizaram-se 240 aves com 40 semanas de idade distribuídas em esquema fatorial 5 × 2, composto de cinco níveis de fósforo disponível (0,094; 0,194; 0,294; 0,394 e 0,494%) e dois de fitase (0 e 300 unidades de fitase - UF). No experimento 2, utilizaram-se 288 aves com 44 semanas de idade, distribuídas também em esquema fatorial 3 × 4, composto de três níveis de fósforo disponível (0,094; 0,294 e 0,494%) e quatro de fitase (0; 300; 600 e 1.200 UF). No experimento 1, não houve interação fósforo disponível × fitase, mas o nível de fósforo disponível influenciou, de forma quadrática, a produção (PR) e a massa (MO) de ovos, os níveis plasmáticos de fósforo e a conversão por massa de ovos (CMO) e, de forma linear, o teor de cinzas na tíbia (CT) e a resistência óssea (RO). A adição de 300 UF elevou a disponibilidade do fósforo (de 4,034 para 4,784 mg/dL), o teor de CT (de 41,55 para 42,90%) e a resistência óssea (de 9,678 para 11,135 kgf/mm). No experimento 2, a produção aumentou de forma linear com os níveis de fósforo disponível da ração, que aumentaram linearmente com o aumento do nível de fitase. Os teores de cinzas na tíbia aumentaram até o nível de 567 UF. O aumento do fósforo disponível no nível de 600 UF melhorou de forma linear a massa de ovos, a conversão por massa de ovos e a conversão por dúzia de ovos. A suplementação da ração com menor teor de fósforo disponível (0,094%) com 300 a 1.200 UF melhorou a resistência óssea das aves. Poedeiras exigem em média 0,31 a 0,34% Pd. A adição de 300 UF ou o aumento do fósforo disponível em rações com 600 UF melhora a conversão por massa de ovos. A suplementação de rações deficientes em fósforo disponível com pelo menos 300 UF aumenta os níveis plasmáticos de fósforo, os teores de cinzas na tíbia e a resistência óssea de poedeiras comerciais.

Crescimento e deposição de nutrientes nos órgãos de frangos de corte de duas linhagens comerciais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Crescimento e deposição de nutrientes nas penas, músculo, ossos e pele de frangos de corte de duas linhagens comerciais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Características agronômicas e composição química de oito híbridos de sorgo [Sorghum bicolor (L.) Moench]

O experimento foi conduzido com o objetivo de avaliar as características agronômicas, composição química das frações e da planta inteira de oito híbridos de sorgo, semeados em março de 2000, no sentido de contribuir para os programas de seleção de germoplamas resistentes aos efeitos das estiagens prolongadas e, ao mesmo tempo, apropriados ao processo de ensilagem. Utilizou-se o delineamento em blocos ao acaso com oito tratamentos e três repetições, para avaliar os híbridos AG-2005, BR-700, MASSA-03, 498111, 65E3, 698005, 698007 e 699005. Não houve diferenças significativas entre produção de matéria seca (PMS) e proporção de folhas dos híbridos avaliados. A maior proporção de colmo (41,3%) foi observada no 498111 e a menor no MASSA-03 (28,9%). O híbrido 65E3 apresentou a maior proporção de panícula (43,2%) e o 498111 a menor (28,9%). Quanto à composição química da planta inteira, não foram observadas diferenças significativas entre os híbridos quanto aos teores de matéria seca, matéria mineral, hemicelulose, nitrogênio insolúvel em detergente neutro, nitrogênio insolúvel em detergente ácido e nutrientes digestíveis totais (NDT). Os teores de proteína bruta variaram de 6,5 a 8,8%, fibra em detergente neutro de 57,0 a 70,3%, fibra em detergente ácido de 29,8 a 36,2%, celulose de 25,3 a 31,2% e lignina de 3,6 a 5,5%, sendo estatisticamente diferentes entre os híbridos. O 699005 apresentou o maior teor de carboidratos solúveis (14,5%), diferindo estatisticamente apenas do híbrido 698007 (9,6%). Os híbridos também mostraram diferenças na composição química das frações folhas, colmo e panícula. de forma geral, todos os híbridos apresentaram teores de matéria seca e carboidratos solúveis adequados ao processo de ensilagem. As produções médias de matéria seca dos híbridos (6,2 t/ha), foram altas considerando-se a baixa precipitação ocorrida durante o período experimental. A análise de Cluster sugeriu o agrupamento dos híbridos de maior PMS e menores porcentagens de panícula e NDT e híbridos de menor PMS, porém com maiores porcentagens de panícula e NDT.

Perfil de ácidos graxos, composição centesimal e valor calórico de moluscos crus e cozidos com leite de coco da cidade de Maceió-Al

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Aproveitamento de resíduos de cinza da cana de açúcar em massas cerâmicas

This study aimed to investigate the use of cane sugar ashes from small-scale stills of Eunápolis region, state of Bahia, in pottery mass that can be developed as porcelain stoneware. Bahia is the second largest producer of rum distillery in Brazil. In the production of rum is produced residue called bagasse, which is used to generate electricity in Power plants and in the distillery itself, generating ashes as residue, which is played in nature, causing environmental damage. We studied 5 (five) formulations of 0% 10% 20%, 30% and 40% by weight of the ash, without ignition and 3 (three) formulations of 10%, 20% and 30% with gray ash temperature of 1250ºC. The formulation at 0% by weight of ash was used for a comparison between the traditional mass of porcelain stoneware and the masses with the addition of ash calcined, replacing feldspar. The percentage by weight of kaolin and of Clay was kept the same, 30%, and all raw materials were derived from the state of Bahia. The samples were made in uniaxial array with dimensions of (60 x 20 x 5) mm and compressed to a pressure of 45 MPa. Assays were performed to characterize the raw by X-ray fluorescence, X-ray diffraction, ATD and ATG and Dilatometric analysis. The samples were sintered at temperatures of 1100°C, 1150°C, 1200°C and 1250°C, for the specimens with the ashes without ash and 1150° C and 1200° C for specimens with the gray level of calcined 60 minutes. and then we made a cooling ramp with the same rate of warming until reach ambient temperature. The sintered bodies were characterized by water absorption, porosity, linear shrinkage, bending strength and XRD of the fracture surface and the results analyzed. It was proven, after results of tests performed, that it is possible to use the ash residue of sugar cane bagasse on ceramic coating with the addition of up to 10% wt of the residue ash

Incorporação de cinzas da casca de café na produção de placas cerâmicas para revestimento

Brazil is the world s leading coffee producer. In 2008, 45.99 million of 60 kg bags of benefited coffee were produced. In the process of improvement 50% is grain and 50% is husk, thus, 1.38 million tons of coffee husk are produced annually. The husk is used as combustible in the drying and improvement ovens in the coffee farms, generating ash as residue. These ashes contain a high concentration of alkaline metals and earth metals, mainly K2O and CaO. This work studies the use of this residue in the ceramic tiles industry, as fluxing agents in substitution to the feldspar. Ten mixtures with equal ratios of clay and kaolin, proceeding from Bahia and the residue (varying from 30 to 5%) were defined and produced in uniaxial tool die of 60x20mm with approximately 5 mm of thickness and 45MPa compacting pressure. The samples were fired in four different temperatures: 1100 °C, 1150 °C, 1185 °C and 1200 °C during 60 minutes and characterized by means of X-ray fluorescence, X-ray diffraction, gravimetric thermal analysis and differential thermal analysis. The results of water absorption, apparent porosity, linear shrinkage, XRD, dilatometry, flexural strength and SEM were also analysed. The test specimen with addition of 10% of ash fired in 1200 °C resulted in 0.18% water absorption and 40.77 MPa flexural strength, being classified as porcelain stoneware tiles according to ABNT, UNI and ISO norms