Gas boosted solar water heaters : Queensland case studies of installation practices in new homes

Because of the greenhouse gas emissions implications of the market dominating electric hot water systems, governments in Australia have implemented policies and programs to encourage the uptake of solar water heaters (SWHs) in the residential market as part of climate change adaptation and mitigation strategies. The cost-benefit analysis that usually accompanies all government policy and program design could be simplistically reduced to the ratio of expected greenhouse gas reductions of SWH to the cost of a SWH. The national Register of Solar Water Heaters specifies how many renewable energy certificates (RECs) are allocated to complying SWHs according to their expected performance, and hence greenhouse gas reductions, in different climates. Neither REC allocations nor rebates are tied to actual performance of systems. This paper examines the performance of instantaneous gas-boosted solar water heaters installed in new residences in a housing estate in south-east Queensland in the period 2007 – 2010. The evidence indicates systemic failures in installation practices, resulting in zero solar performance or dramatic underperformance (estimated average 43% solar contribution). The paper will detail the faults identified, and how these faults were eventually diagnosed and corrected. The impacts of these system failures on end-use consumers are discussed before concluding with a brief overview of areas where further research is required in order to more fully understand whole of supply chain implications.

A model of organisational leadership development informing succession development : elements and practices

It is noted from observations of Compton (2009), Richards (2008), Taylor and Bennett (2002), and others that succession leadership planning and development fails to receive adequate attention in the corporate sector (see Byham 2002; Richards 2008; Wellins and Byham 2001). This paper acknowledges a marked paucity of systematic succession leadership development in education organisations. The need would seem to be compounded at a time when substantial attrition in the leadership ranks is expected over the next five years, reflecting widespread workforce demographics (Busine and Watt 2005; Jacobzone, Cambois, Chaplain, and Robine 1998; Taylor and Bennett 2002). The Lantern model has been developed in response to a perceived need to offer an integrated, systematic approach to organisational and succession leadership development. The model offers an organising framework for considering succession leadership development in a strategic, integrated way. The concept is based on organisational development and leadership literature which sees leadership development not as a series of 'tacked on' activities but as an organic 'whole of organisation' approach fostering the relevant knowledge, skills and understandings which support and 'grow' leaders as the organisation goes about its business. This paper explores how such an ideal might happen, and it suggests that pursuing such an ideal is timely. The leadership baton is set to shift at an accelerated rate in universities, as for organisations broadly, owing to age-related attrition. Moreover, given the increased complexity and demands of the leadership remit in the education leadership environment, it would seem particularly opportune to explore a framework concentrating on engendering a positive, connected organisational climate capable of growing strategic leadership strength from within. Eight core elements of the model, derived from the literature and practice research, are explored. The Lantern model purports to 'cover the bases' of succession leadership development, with particular reference to the education environment. The model is next described

Enhancing the transition of commencing students into university : an institution-wide approach

The importance of the first year experience (FYE) to success at university is well documented and supported with the transition into university regarded as crucial. While there is also support for the notion that a successful FYE should have a whole-of-institution focus and models have been proposed, many institutions still face challenges in achieving institution-wide FYE program implementation. This paper discusses the origins, theoretical and empirical bases and structure of an institution-wide approach to the FYE. It uses a case study of the Transitions In Project (TIP) at the Queensland University of Technology to illustrate how institution-wide FYE program implementation can be achieved and sustained. TIP had four inter-related projects focussing on at-risk students, first year curriculum, learning resources and staff development. The key aim of TIP was to identify good practice and institutionalise it in a sustainable way. The degree of success in achieving this is evaluated.

Issues and concerns of microscopic calibration process at different network levels : case study of Pacific Motorway

Calibration process in micro-simulation is an extremely complicated phenomenon. The difficulties are more prevalent if the process encompasses fitting aggregate and disaggregate parameters e.g. travel time and headway. The current practice in calibration is more at aggregate level, for example travel time comparison. Such practices are popular to assess network performance. Though these applications are significant there is another stream of micro-simulated calibration, at disaggregate level. This study will focus on such microcalibration exercise-key to better comprehend motorway traffic risk level, management of variable speed limit (VSL) and ramp metering (RM) techniques. Selected section of Pacific Motorway in Brisbane will be used as a case study. The discussion will primarily incorporate the critical issues encountered during parameter adjustment exercise (e.g. vehicular, driving behaviour) with reference to key traffic performance indicators like speed, lane distribution and headway; at specific motorway points. The endeavour is to highlight the utility and implications of such disaggregate level simulation for improved traffic prediction studies. The aspects of calibrating for points in comparison to that for whole of the network will also be briefly addressed to examine the critical issues such as the suitability of local calibration at global scale. The paper will be of interest to transport professionals in Australia/New Zealand where micro-simulation in particular at point level, is still comparatively a less explored territory in motorway management.

Issues and concerns of microscopic calibration process at different network levels : case study of pacific motorway

Calibration process in micro-simulation is an extremely complicated phenomenon. The difficulties are more prevalent if the process encompasses fitting aggregate and disaggregate parameters e.g. travel time and headway. The current practice in calibration is more at aggregate level, for example travel time comparison. Such practices are popular to assess network performance. Though these applications are significant there is another stream of micro-simulated calibration, at disaggregate level. This study will focus on such micro-calibration exercise-key to better comprehend motorway traffic risk level, management of variable speed limit (VSL) and ramp metering (RM) techniques. Selected section of Pacific Motorway in Brisbane will be used as a case study. The discussion will primarily incorporate the critical issues encountered during parameter adjustment exercise (e.g. vehicular, driving behaviour) with reference to key traffic performance indicators like speed, land distribution and headway; at specific motorway points. The endeavour is to highlight the utility and implications of such disaggregate level simulation for improved traffic prediction studies. The aspects of calibrating for points in comparison to that for whole of the network will also be briefly addressed to examine the critical issues such as the suitability of local calibration at global scale. The paper will be of interest to transport professionals in Australia/New Zealand where micro-simulation in particular at point level, is still comparatively a less explored territory in motorway management.

Hunters & gatherers : strategies for curriculum mapping and data collection for assurance of learning

Assurance of learning is a predominant feature in both quality enhancement and assurance in higher education. Assurance of learning is a process that articulates explicit program outcomes and standards, and systematically gathers evidence to determine the extent to which performance matches expectations. Benefits accrue to the institution through the systematic assessment of whole of program goals. Data may be used for continuous improvement, program development, and to inform external accreditation and evaluation bodies. Recent developments, including the introduction of the Tertiary Education and Quality Standards Agency (TEQSA) will require universities to review the methods they use to assure learning outcomes. This project investigates two critical elements of assurance of learning: 1. the mapping of graduate attributes throughout a program; and 2. the collection of assurance of learning data. An audit was conducted with 25 of the 39 Business Schools in Australian universities to identify current methods of mapping graduate attributes and for collecting assurance of learning data across degree programs, as well as a review of the key challenges faced in these areas. Our findings indicate that external drivers like professional body accreditation (for example: Association to Advance Collegiate Schools of Business (AACSB)) and TEQSA are important motivators for assuring learning, and those who were undertaking AACSB accreditation had more robust assurance of learning systems in place. It was reassuring to see that the majority of institutions (96%) had adopted an embedding approach to assuring learning rather than opting for independent standardised testing. The main challenges that were evident were the development of sustainable processes that were not considered a burden to academic staff, and obtainment of academic buy in to the benefits of assuring learning per se rather than assurance of learning being seen as a tick box exercise. This cultural change is the real challenge in assurance of learning practice.

Evaluation of the skills for preventing injury in youth program : impact on health risk behaviors, injury and school connectedness

Injury is the leading cause of death among young people, and involvement in health risk behaviors, such as alcohol use and transport-related risks, is related to increased risk for injury. Effective health promotion programs for adolescents focus on multiple levels, including relationships with peers and parents, student knowledge, behavior and attitudes, and school-level factors such as school connectedness. This study describes the pilot evaluation of a comprehensive, multi-level injury prevention program for 13-14 year old adolescents, targeting change in injury associated with transport and alcohol risks. The program, called Skills for Preventing Injury in Youth (SPIY), incorporates two primary elements: an 8-week, teacher delivered attitude and behavior change curriculum with peer protection and first aid messages; and professional development for program teachers focusing on strategies to increase students’ connectedness to school. Five Australian high schools were recruited for the pilot evaluation research, with three being assigned to receive intervention components and two assigned as curriculum-as-usual controls. In the intervention schools, 118 Year 8 students participated in surveys at baseline, with 105 completing surveys at follow up, six months following the intervention. In the control schools, 196 Year 8 students completed surveys at baseline and 207 at follow up. Survey measures included self-reported injury, risk taking behavior and school connectedness. Results showed that students in the control schools were significantly more likely to report riding bikes without helmets, riding with dangerous drivers, having driven cars on the road, and using alcohol six months after the program, while the intervention group showed no such increase in these behaviors. Additionally, students in the control schools were significantly more likely to report having had pedestrian-related injuries at follow up than they were at the baseline measurement, while intervention school students showed no change. There was also a trend observed in terms of a decrease in bicycle related injuries among intervention school students, compared with a slight increasing trend in bicycle injuries among control students. Overall, scores on the school connectedness scale decreased significantly from baseline to follow up for both intervention and control students, however measurement limitations may have impacted on results relating to students’ connectedness. Overall, the SPIY program has shown promising results in regards to prevention of students’ health risk behavior and injuries. Evidence suggests that the curriculum component was important; however there was limited evidence to suggest that teacher training in school connectedness strategies contributed to these promising results. While school connectedness may be an important factor to target in risk and injury prevention programs, programs may need to incorporate whole-of-school strategies or target a broader range of teachers than were selected for the current research.

An examination of recent taxation amendments, corporate law reforms and Queensland legislative reforms affecting nonprofit organisations

There is a tax amendment bill which will be debated. The Government has promised to outline its plan for the reform of the taxation system sometime this year. The plans appear to go beyond the mere introduction of some sort of goods and services tax to reform of the whole taxation system including fiscal relations with the States. Not for profit organisations will find their taxation environment will change. Governments are reluctant to permit exemptions to a GST style arrangements. GST trade offs such as reduced income tax rates and abolishing indirect taxes are useless to nonprofit organisations, as many are already exempt from such imposts. Administrative changes to tax collections may also have an impact. If the government decides to make an individual PAYE taxpayer return optional in exchange for no or standard deductions, this may have an effect on fundraising. The FBT and salary packaging schemes that not for profit organisations use will be under intense scrutiny. A regionalisation of the ATO along the successful model of the ASC would see discrete areas such as not for profit exemptions being centralised in one regional office for the whole of Australia. For example the Tasmanian ASC Office has the responsibility for much work in respect of corporate charities and not for profit companies.

Impact of opening a new emergency department on healthcare service and patient outcomes : analyses based on linking ambulance, emergency and hospital databases

Background Emergency department (ED) crowding caused by access block is an increasing public health issue and has been associated with impaired healthcare delivery, negative patient outcomes and increased staff workload. Aim To investigate the impact of opening a new ED on patient and healthcare service outcomes. Methods A 24-month time series analysis was employed using deterministically linked data from the ambulance service and three ED and hospital admission databases in Queensland, Australia. Results Total volume of ED presentations increased 18%, while local population growth increased by 3%. Healthcare service and patient outcomes at the two pre-existing hospitals did not improve. These outcomes included ambulance offload time: (Hospital A PRE: 10 min, POST: 10 min, P < 0.001; Hospital B PRE: 10 min, POST: 15 min, P < 0.001); ED length of stay: (Hospital A PRE: 242 min, POST: 246 min, P < 0.001; Hospital B PRE: 182 min, POST: 210 min, P < 0.001); and access block: (Hospital A PRE: 41%, POST: 46%, P < 0.001; Hospital B PRE: 23%, POST: 40%, P < 0.001). Time series modelling indicated that the effect was worst at the hospital furthest away from the new ED. Conclusions An additional ED within the region saw an increase in the total volume of presentations at a rate far greater than local population growth, suggesting it either provided an unmet need or a shifting of activity from one sector to another. Future studies should examine patient decision making regarding reasons for presenting to a new or pre-existing ED. There is an inherent need to take a ‘whole of health service area’ approach to solve crowding issues.

Performance analysis of IEC 61850 sampled value process bus networks

Process bus networks are the next stage in the evolution of substation design, bringing digital technology to the high voltage switchyard. Benefits of process buses include facilitating the use of Non-Conventional Instrument Transformers, improved disturbance recording and phasor measurement and the removal of costly, and potentially hazardous, copper cabling from substation switchyards and control rooms. This paper examines the role a process bus plays in an IEC 61850 based Substation Automation System. Measurements taken from a process bus substation are used to develop an understanding of the network characteristics of "whole of substation" process buses. The concept of "coherent transmission" is presented and the impact of this on Ethernet switches is examined. Experiments based on substation observations are used to investigate in detail the behavior of Ethernet switches with sampled value traffic. Test methods that can be used to assess the adequacy of a network are proposed, and examples of the application and interpretation of these tests are provided. Once sampled value frames are queued by an Ethernet switch the additional delay incurred by subsequent switches is minimal, and this allows their use in switchyards to further reduce communications cabling, without significantly impacting operation. The performance and reliability of a process bus network operating with close to the theoretical maximum number of digital sampling units (merging units or electronic instrument transformers) was investigated with networking equipment from several vendors, and has been demonstrated to be acceptable.

Community interventions for physical activity : the role of a new Cochrane systematic review

Introduction: Systematic reviews are essential in summarising the results of a range of research studies on a specific topic into a single report. They serve as a key source of evidence-based information to support and develop policy and practice for healthy communities. This presentation will examine a new review of community-wide strategies to increase population levels of physical activity and compare it to an earlier Community Guide Review (CGR) of Community-wide campaigns to increase physical activity which recommended community wide interventions. Methods: We registered a Cochrane Systematic Review (CSR) title, published a protocol and recently completed the review of Community-wide interventions to increase physical activity. We compared the definitions, design and findings of the CSR to the CGR. Results: The two reviews differed remarkably in their conclusions with the CGR recommending “strong evidence exists that community-wide campaigns are effective in increasing levels of physical activity”, and the new CSR stating “The body of evidence in this review does not support the hypothesis that multi-component community wide interventions effectively increase population levels of physical activity”. We observed that both reviews examined multi-component interventions as a “combined package”. Possible explanations for the different conclusions may be due to the definition of community (CSR defined community as “comprising those persons residing in a geographically defined community, such as a village, town, or city”, excluding interventions which were whole of state or country, and CGR as “a group of individuals who share one or more characteristics. The CSR utilised a logic model at various stages of the review process and explicitly defined a combination of strategies encompassed within the intervention. The CSR included 25 and CGR 10 studies, respectively. Six of the 10 studies that were included in CGR were excluded from the CSR due to issues relating to study design, intervention definition or duration. The two reviews also differ in function as the CSR seeks to summarise global evidence and included 7 studies in low-income countries, where as the CGR contained only studies deemed relevant to the USA context. Discussion: Differences in the findings between older and newer reviews can be due to a variety of factors. For example, in updating a review the definition of an intervention can be changed. Further, differences may also be due to improvements in the standards and methodologies for systematic reviews as well as the inclusion of newer studies. These factors need to be understood whenever differences between newer and older reviews are considered.

Modelling the flow of cane constituents through the milling process of a raw sugar factory

This thesis reports on an investigation to develop an advanced and comprehensive milling process model of the raw sugar factory. Although the new model can be applied to both, the four-roller and six-roller milling units, it is primarily developed for the six-roller mills which are widely used in the Australian sugar industry. The approach taken was to gain an understanding of the previous milling process simulation model "MILSIM" developed at the University of Queensland nearly four decades ago. Although the MILSIM model was widely adopted in the Australian sugar industry for simulating the milling process it did have some incorrect assumptions. The study aimed to eliminate all the incorrect assumptions of the previous model and develop an advanced model that represents the milling process correctly and tracks the flow of other cane components in the milling process which have not been considered in the previous models. The development of the milling process model was done is three stages. Firstly, an enhanced milling unit extraction model (MILEX) was developed to access the mill performance parameters and predict the extraction performance of the milling process. New definitions for the milling performance parameters were developed and a complete milling train along with the juice screen was modelled. The MILEX model was validated with factory data and the variation in the mill performance parameters was observed and studied. Some case studies were undertaken to study the effect of fibre in juice streams, juice in cush return and imbibition% fibre on extraction performance of the milling process. It was concluded from the study that the empirical relations developed for the mill performance parameters in the MILSIM model were not applicable to the new model. New empirical relations have to be developed before the model is applied with confidence. Secondly, a soluble and insoluble solids model was developed using modelling theory and experimental data to track the flow of sucrose (pol), reducing sugars (glucose and fructose), soluble ash, true fibre and mud solids entering the milling train through the cane supply and their distribution in juice and bagasse streams.. The soluble impurities and mud solids in cane affect the performance of the milling train and further processing of juice and bagasse. New mill performance parameters were developed in the model to track the flow of cane components. The developed model is the first of its kind and provides some additional insight regarding the flow of soluble and insoluble cane components and the factors affecting their distribution in juice and bagasse. The model proved to be a good extension to the MILEX model to study the overall performance of the milling train. Thirdly, the developed models were incorporated in a proprietary software package "SysCAD’ for advanced operational efficiency and for availability in the ‘whole of factory’ model. The MILEX model was developed in SysCAD software to represent a single milling unit. Eventually the entire milling train and the juice screen were developed in SysCAD using series of different controllers and features of the software. The models developed in SysCAD can be run from macro enabled excel file and reports can be generated in excel sheets. The flexibility of the software, ease of use and other advantages are described broadly in the relevant chapter. The MILEX model is developed in static mode and dynamic mode. The application of the dynamic mode of the model is still under progress.

Quantification of ebullitive and diffusive methane release to atmosphere from a water storage

Accurately quantifying total freshwater storage methane release to atmosphere requires the spatial–temporal measurement of both diffusive and ebullitive emissions. Existing floating chamber techniques provide localised assessment of methane flux, however, significant errors can arise when weighting and extrapolation to the entire storage, particularly when ebullition is significant. An improved technique has been developed that compliments traditional chamber based experiments to quantify the storage-scale release of methane gas to atmosphere through ebullition using the measurements from an Optical Methane Detector (OMD) and a robotic boat. This provides a conservative estimate of the methane emission rate from ebullition along with the bubble volume distribution. It also georeferences the area of ebullition activity across entire storages at short temporal scales. An assessment on Little Nerang Dam in Queensland, Australia, demonstrated whole storage methane release significantly differed spatially and throughout the day. Total methane emission estimates showed a potential 32-fold variation in whole-of-dam rates depending on the measurement and extrapolation method and time of day used. The combined chamber and OMD technique showed that 1.8–7.0% of the surface area of Little Nerang Dam is accounting for up to 97% of total methane release to atmosphere throughout the day. Additionally, over 95% of detectable ebullition occurred in depths less than 12 m during the day and 6 m at night. This difference in spatial and temporal methane release rate distribution highlights the need to monitor significant regions of, if not the entire, water storage in order to provide an accurate estimate of ebullition rates and their contribution to annual methane emissions.

Placement Trajectory : mapping the journeys of children and young people in out-of-home care

Significant problems confront our child protection out-of-home care system including: high costs; increasing numbers of children and young people entering and remaining in care longer; high frequency of placement movement; and, negative whole-of-life outcomes for children and young people who have exited care. National policy and research agendas recognise the importance of enhancing the evidence base in out-of-home care to inform the development of policy, programs and practice, and improve longitudinal outcomes of children and young people. The authors discuss the concept of placement trajectory as a framework for research and systems analysis in the out-of-home context. While not without limitations, the concept of placement trajectory is particularly useful in understanding the factors influencing placement movement and stability. Increasing the evidence base in this area can serve to enhance improved outcomes across the lifespan for children and young people in the out-of-home care system.

The Implications of Activity Based Funding for Emergency Departments : A Comprehensive Literature Review

Executive Summary Emergency Departments (EDs) locally, nationally and internationally are becoming increasingly busy. Within this context, it can be challenging to deliver a health service that is safe, of high quality and cost-effective. Whilst various models are described within the literature that aim to measure ED ‘work’ or ‘activity’, they are often not linked to a measure of costs to provide such activity. It is important for hospital and ED managers to understand and apply this link so that optimal staffing and financial resourcing can be justifiably sought. This research is timely given that Australia has moved towards a national Activity Based Funding (ABF) model for ED activity. ABF is believed to increase transparency of care and fairness (i.e. equal work receives equal pay). ABF involves a person-, performance- or activity-based payment system, and thus a move away from historical “block payment” models that do not incentivise efficiency and quality. The aim of the Statewide Workforce and Activity-Based Funding Modelling Project in Queensland Emergency Departments (SWAMPED) is to identify and describe best practice Emergency Department (ED) workforce models within the current context of ED funding that operates under an ABF model. The study is comprised of five distinct phases. This monograph (Phase 1) comprises a systematic review of the literature that was completed in June 2013. The remaining phases include a detailed survey of Queensland hospital EDs’ resource levels, activity and operational models of care, development of new resource models, development of a user-friendly modelling interface for ED mangers, and production of a final report that identifies policy implications. The anticipated deliverable outcome of this research is the development of an ABF based Emergency Workforce Modelling Tool that will enable ED managers to profile both their workforce and operational models of care. Additionally, the tool will assist with the ability to more accurately inform adequate staffing numbers required in the future, inform planning of expected expenditures and be used for standardisation and benchmarking across similar EDs. Summary of the Findings Within the remit of this review of the literature, the main findings include: 1. EDs are becoming busier and more congested Rising demand, barriers to ED throughput and transitions of care all contribute to ED congestion. In addition requests by organisational managers and the community require continued broadening of the scope of services required of the ED and further increases in demand. As the population live longer with more lifestyle diseases their propensity to require ED care continues to grow. 2. Various models of care within EDs exist Models often vary to account for site specific characteritics to suit staffing profile, ED geographical location (e.g. metropolitan or rural site), and patient demographic profile (e.g. paediatrics, older persons, ethnicity). Existing and new models implemented within EDs often depend on the target outcome requiring change. Generally this is focussed on addressing issues at the input, throughput or output areas of the ED. Even with models targeting similar demographic or illness, the structure and process elements underpinning the model can vary, which can impact on outcomes and variance to the patient and carer experience between and within EDs. Major models of care to manage throughput inefficiencies include: A. Workforce Models of Care focus on the appropriate level of staffing for a given workload to provide prompt, timely and clinically effective patient care within an emergency care setting. The studies reviewed suggest that the early involvement of senior medical decision maker and/or specialised nursing roles such as Emergency Nurse Practitioners and Clinical Initiatives Nurse, primary contact or extended scope Allied Health Practitioners can facilitate patient flow and improve key indicators such as length of stay and reducing the number of those who did not wait to be seen amongst others. B. Operational Models of Care within EDs focus on mechanisms for streaming (e.g. fast-tracking) or otherwise grouping patient care based on acuity and complexity to assist with minimising any throughput inefficiencies. While studies support the positive impact of these models in general, it appears that they are most effective when they are adequately resourced. 3. Various methods of measuring ED activity exist Measuring ED activity requires careful consideration of models of care and staffing profile. Measuring activity requires the ability to account for factors including: patient census, acuity, LOS, intensity of intervention, department skill-mix plus an adjustment for non-patient care time. 4. Gaps in the literature Continued ED growth calls for new and innovative care delivery models that are safe, clinically effective and cost effective. New roles and stand-alone service delivery models are often evaluated in isolation without considering the global and economic impact on staffing profiles. Whilst various models of accounting for and measuring health care activity exist, costing studies and cost effectiveness studies are lacking for EDs making accurate and reliable assessments of care models difficult. There is a necessity to further understand, refine and account for measures of ED complexity that define a workload upon which resources and appropriate staffing determinations can be made into the future. There is also a need for continued monitoring and comprehensive evaluation of newly implemented workforce modelling tools. This research acknowledges those gaps and aims to: • Undertake a comprehensive and integrated whole of department workforce profiling exercise relative to resources in the context of ABF. • Inform workforce requirements based on traditional quantitative markers (e.g. volume and acuity) combined with qualitative elements of ED models of care; • Develop a comprehensive and validated workforce calculation tool that can be used to better inform or at least guide workforce requirements in a more transparent manner.