Estudo de anomalias eletromagnéticas de um condutor tabular vertical sob camadas parcialmente condutiva em multifrequência e multiseparação através de modelamento analógico

A resposta eletromagnética (EM) de um corpo condutivo envolvido por uma zona parcialmente condutiva, torna-se bastante diferente daquela de um corpo condutivo em um meio altamente resistivo. As zonas parcialmente condutivas, como por exemplo, rocha encaixante, halo de sulfetos disseminados ou manto de intemperismo, que envolvem o corpo condutivo, afetam a resposta EM de diferentes maneiras, dependendo de suas características físicas e geométricas e, em particular, do sistema de prospecção EM utilizado. Neste trabalho em modelamento analógico, foi feita uma análise de anomalias EM provocadas por corpos condutivos tabulares verticais sob manto de intemperismo, em levantamentos terrestres para diferentes sistemas de bobinas - horizontal coplanar, vertical coplanar e vertical coaxial - em oito frequências na faixa de 250 Hz a 35 kHz e separações entre as bobinas de 0,15; 0,20 e 0,25m. O manto de intemperismo foi simulado por folhas de aço finas dispostas horizontalmente e o corpo condutor principal por folhas de alumínio finas colocadas verticalmente. As dimensões das folhas foram determinadas de acordo com as condições de modelamento para o plano e o semi-plano. Foram utilizados três corpos e três mantos com diferentes espessuras e condutividades, simulando, deste modo, diversas situações geológicas. Os resultados mostraram que cada sistema de bobinas é afetado diferentemente pela presença do manto de intemperismo. Para a análise dos resultados foi plotado um conjunto de diagramas considerando os valores pico-a-pico das anomalias em fase e em quadratura. Um outro conjunto de diagramas mostra as amplitudes máximas em fase, que ocorrem quando a componente em quadratura se anula em uma frequência relativamente baixa para um conjunto de corpo-manto, e as amplitudes máximas em quadratura, que ocorrem quando a resposta em fase atinge um mínimo próximo de zero, em frequências relativamente altas. Com isto foi possível conhecer a faixa de frequências para cada sistema de bobinas, onde a resposta EM se encontra o mínimo afetada pela presença do manto de intemperismo. A maior amplitude na resposta é obtida no sistema horizontal coplanar e a menor no sistema vertical coplanar. Um aumento na separação entre as bobinas é acompanhado por um deslocamento da anomalia para baixas frequências. A faixa de frequências, onde a presença do manto tem pouca influência na resposta do corpo condutivo, e maior para o sistema vertical coaxial e menor para o sistema horizontal coplanar. Esses resultados dão uma luz para o conhecimento da posição e da largura da banda de frequências utilizável, assim como as melhores separações entre transmissor-receptor, para auxiliar no planejamento de sistemas de prospecção EM, de modo que a resposta fique o mais livre possível de sinais indesejáveis, tais como os causados pela presença do manto de intemperismo.

Hydrogen sulphide removal from air by biotrickling filter using open-pore polyurethane foam as a carrier

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise estrutural e microtectônica da inflexão do jordino e depósitos de ouro associados no greenstone belt de Pilar de Goiás

The study area is included in the geological context of the Goias Median Massif, a region where there are associations of Archean granite-gneiss complex (Block Moquém) and a Paleoproterozoic metavolcano-sedimentary sequence ( Pilar greenstone belt ). At the south of area, the greenstone sequence is partially overlain by Neopreoterozoic metasediments of the Araxá Group. The lithostratigraphic units of the Pilar greenstone belt define a shift from about N30W direction (north of the deposit) to N60 and 70W in the region south of the Jordino deposit, where are truncated by the Araxá Group rocks. Mineralogical associations described in this paper allow to indicate that the regional metamorphism that affected the rocks of the greenstone belt and Araxá Group, in the mapped area, reached the upper greenschist facies (garnet zone). Data obtained during mapping and by microtectonics analysis allow to indicate the existence of at least four deformational events that acted on the rocks of the Guarinos greenstone belt and Araxá Group, represented by the phases called Dn-1, Dn, Dn + 1 and Dn+2. It was observed that the pattern of sulphide porfitoblasts in mineralized levels is similar to garnet, biotite and muscovite porfiroblasts (tardi to post Dn) that marks the metamorphic peak of the area

Single precursor route to efficient cobalt sulphide counter electrodes for dye sensitized solar cells

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Study of ceramic block manufacture with the addition of waste from iron ore extraction

This work is intended to study the possibility of adding an amount of waste from iron mining in the ceramic mass. Clay and coal, from Vale do Paraiba, Sao Paulo, Brazil, were used in this research. These raw materials are used in the ceramic block manufacture. Clay and waste were analyzed by X-ray fluorescence and X-ray diffraction, particle size, differential thermal and thermogravimetric analysis. Liquid limit and plasticity index tests were performed in order to determine the amount of waste that which should be used in the ceramic mass. After determining the amount of waste, all samples were uniaxially pressed and sintered at 900 degrees C. Surface roughness measurements, apparent porosity and bulk density technique and three-point flexural tests were also performed to characterize the samples. The results showed that by adding the exact amount of waste, which was determined by the essays, it is possible to manufacture solid bricks.

Operational and environmental assessment on the use of charcoal in iron ore sinter production

A study was carried out into the use of charcoal as a supplementary fuel in the iron-ore sintering process. The primary fuel was coke breeze and anthracite with 0, 10, 25, 50 and 100% replacement of the energy input with charcoal to produce sinter. This was achieved by considering the carbon content of each fuel and its corresponding participation on fuel blending, in order to have the same carbon input in each test run. An extensive analysis of the environmental impact was carried out regarding the atmospheric pollutants characterization (dust, sulphur dioxide, nitrogen oxides, carbon monoxide, carbon dioxide, methane, total hydrocarbons, and dioxins and furans). Experimental results indicate that fuel blending where 50% of the heat input was provided by charcoal may be comparable with those using 100% coke, under normal sintering conditions, and may result in a 50% reduction on greenhouse gas emission. It was also observed that while dust, methane and hydrocarbons emissions increased, the total dioxins and furans, expressed as polychlorinated dibenzodioxins/furans, decreased approximately 50% when compared with operation with 100% coke.

Dissolução redutiva de minério de ferro por Acidithiobacillus ferrooxidans para a recuperação de metais de interesse econômico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Carbothermal Reduction of Iron Ore Applying Microwave Energy

This paper presents the results of a study on carbothermal reduction of iron ore made under the microwave field in equipment specially developed for this purpose. The equipment allows the control of radiated and reflected microwave power, and therefore measures the microwave energy actually applied to the load in the reduction process. It also allows performing energy balances and determining the reaction rate with high levels of confidence by simultaneously measuring temperature and mass of the material upon reduction with high reproducibility. We used a microwave generator of 2.45?GHz with variable power up to 3000?W. Self-reducing pellets under argon atmosphere, containing iron ore and petroleum coke, with 3.5?g of mass and 15?mm of diameter were declined. We obtained the kinetic curves of reduction of iron ore and of energy consumption to the process in the maximum electric field, in the maximum magnetic field and at different values of power/mass. The data allow analyzing how the microwave energy was actually consumed in the reduction of ore.

Copper ore type definition from Sossego Mine using X-ray diffraction and cluster analysis technique

This paper presents the classification of 110 copper ore samples from Sossego Mine, based on X-ray diffraction and cluster analysis. The comparison based on the position and the intensity of the diffracted peaks allowed the distinction of seven ore types, whose differences refer to the proportion of major minerals: quartz, feldspar, actinolite, iron oxides, mica and chlorite. There was a strong correlation between the grouping and the location of the samples in Sequeirinho and Sossego orebodies. This relationship is due to different types and intensities of hydrothermal alteration prevailing in each body, which reflect the mineralogical composition and thus the X-ray diffractograms of samples.

Disintegration on heating of a Brazilian manganese lump ore

This pioneering study characterized the chemical, physical and mineralogical aspects of the Urucum Standard manganese ore typology, and evaluated some of its metallurgical characteristics, such as the main mineral heat decompositions, and the particle disintegration at room temperature and under continuous heating. A one-ton sample of ore was received, homogenized and quartered. Representative samples were collected and characterized with the aid of techniques, such as ICP-AES, XRD, SEM-EDS, BET and OM. Representative samples with particle sizes between 9.5 mm and 15.9 mm were separated to perform tumbling tests at room temperature, and thermogravimetry tests for both air and nitrogen constant flow at different temperatures. After each heating cycle, the mechanical strength of the orewas evaluated by means of screening and tumbling procedures. The Urucum Standard typology was classified as an oxidized anhydrous ore, with a high manganese content (~47%). This typology ismainly composed of cryptomelane and pyrolusite; however there is a significantamount of hematite. The Urucum Standard particles presented low susceptibility to disintegration at room temperature, but as temperature increased, susceptibility increased. No significant differences were observed between the tests done with the air or nitrogen injections.