Technical note : modelling a complex micro-multileaf collimator using the standard BEAMnrc distribution

Purpose: The component modules in the standard BEAMnrc distribution may appear to be insufficient to model micro-multileaf collimators that have tri-faceted leaf ends and complex leaf profiles. This note indicates, however, that accurate Monte Carlo simulations of radiotherapy beams defined by a complex collimation device can be completed using BEAMnrc's standard VARMLC component module.---------- Methods: That this simple collimator model can produce spatially and dosimetrically accurate micro-collimated fields is illustrated using comparisons with ion chamber and film measurements of the dose deposited by square and irregular fields incident on planar, homogeneous water phantoms.---------- Results: Monte Carlo dose calculations for on- and off-axis fields are shown to produce good agreement with experimental values, even upon close examination of the penumbrae.--------- Conclusions: The use of a VARMLC model of the micro-multileaf collimator, along with a commissioned model of the associated linear accelerator, is therefore recommended as an alternative to the development or use of in-house or third-party component modules for simulating stereotactic radiotherapy and radiosurgery treatments. Simulation parameters for the VARMLC model are provided which should allow other researchers to adapt and use this model to study clinical stereotactic radiotherapy treatments.

Use of micro-ATR/FTIR imaging to study heterogeneous polymer oxidation by direct solvent casting onto the ATR IRE

A technique is described whereby micro-ATR/FTIR imaging can be used to follow polymer degradation reactions in situ in real time. The internal reflection element (IRE) assembly is removed from the ATR objective and polymer is solvent cast directly onto the IRE surface. The polymer is then subjected to degradation conditions and molecular structural changes monitored by periodically replacing the IRE assembly back in the ATR objective and collecting spectra which can be used to construct images. This approach has the benefit that the same part of the sample is always studied, and that contact by pressure which might damage the polymer surface is not required. The technique is demonstrated using the polymer Topas which was degraded by exposure to UVC light in air.

Micro-family-owned business : transitory survival mechanism or long term wealth creator?

Principal Topic: Entrepreneurship is key to employment, innovation and growth (Acs & Mueller, 2008), and as such, has been the subject of tremendous research in both the economic and management literatures since Solow (1957), Schumpeter (1934, 1943), and Penrose (1959). The presence of entrepreneurs in the economy is a key factor in the success or failure of countries to grow (Audretsch and Thurik, 2001; Dejardin, 2001). Further studies focus on the conditions of existence of entrepreneurship, influential factors invoked are historical, cultural, social, institutional, or purely economic (North, 1997; Thurik 1996 & 1999). Of particular interest, beyond the reasons behind the existence of entrepreneurship, are entrepreneurial survival and good ''performance'' factors. Using cross-country firm data analysis, La Porta & Schleifer (2008) confirm that informal micro-businesses provide on average half of all economic activity in developing countries. They find that these are utterly unproductive compared to formal firms, and conclude that the informal sector serves as a social security net ''keep[ing] millions of people alive, but disappearing over time'' (abstract). Robison (1986), Hill (1996, 1997) posit that the Indonesian government under Suharto always pointed to the lack of indigenous entrepreneurship , thereby motivating the nationalisation of all industries. Furthermore, the same literature also points to the fact that small businesses were mostly left out of development programmes because they were supposed less productive and having less productivity potential than larger ones. Vial (2008) challenges this view and shows that small firms represent about 70% of firms, 12% of total output, but contribute to 25% of total factor productivity growth on average over the period 1975-94 in the industrial sector (Table 10, p.316). ---------- Methodology/Key Propositions: A review of the empirical literature points at several under-researched questions. Firstly, we assess whether there is, evidence of small family-business entrepreneurship in Indonesia. Secondly, we examine and present the characteristics of these enterprises, along with the size of the sector, and its dynamics. Thirdly, we study whether these enterprises underperform compared to the larger scale industrial sector, as it is suggested in the literature. We reconsider performance measurements for micro-family owned businesses. We suggest that, beside productivity measures, performance could be appraised by both the survival probability of the firm, and by the amount of household assets formation. We compare micro-family-owned and larger industrial firms' survival probabilities after the 1997 crisis, their capital productivity, then compare household assets of families involved in business with those who do not. Finally, we examine human and social capital as moderators of enterprises' performance. In particular, we assess whether a higher level of education and community participation have an effect on the likelihood of running a family business, and whether it has an impact on households' assets level. We use the IFLS database compiled and published by RAND Corporation. The data is a rich community, households, and individuals panel dataset in four waves: 1993, 1997, 2000, 2007. We now focus on the waves 1997 and 2000 in order to investigate entrepreneurship behaviours in turbulent times, i.e. the 1997 Asian crisis. We use aggregate individual data, and focus on households data in order to study micro-family-owned businesses. IFLS data covers roughly 7,600 households in 1997 and over 10,000 households in 2000, with about 95% of 1997 households re-interviewed in 2000. Households were interviewed in 13 of the 27 provinces as defined before 2001. Those 13 provinces were targeted because accounting for 83% of the population. A full description of the data is provided in Frankenberg and Thomas (2000), and Strauss et alii (2004). We deflate all monetary values in Rupiah with the World Development Indicators Consumer Price Index base 100 in 2000. ---------- Results and Implications: We find that in Indonesia, entrepreneurship is widespread and two thirds of households hold one or several family businesses. In rural areas, in 2000, 75% of households run one or several businesses. The proportion of households holding both a farm and a non farm business is higher in rural areas, underlining the reliance of rural households on self-employment, especially after the crisis. Those businesses come in various sizes from very small to larger ones. The median business production value represents less than the annual national minimum wage. Figures show that at least 75% of farm businesses produce less than the annual minimum wage, with non farm businesses being more numerous to produce the minimum wage. However, this is only one part of the story, as production is not the only ''output'' or effect of the business. We show that the survival rate of those businesses ranks between 70 and 82% after the 1997 crisis, which contrasts with the 67% survival rate for the formal industrial sector (Ter Wengel & Rodriguez, 2006). Micro Family Owned Businesses might be relatively small in terms of production, they also provide stability in times of crisis. For those businesses that provide business assets figures, we show that capital productivity is fairly high, with rates that are ten times higher for non farm businesses. Results show that households running a business have larger family assets, and households are better off in urban areas. We run a panel logit model in order to test the effect of human and social capital on the existence of businesses among households. We find that non farm businesses are more likely to appear in households with higher human and social capital situated in urban areas. Farm businesses are more likely to appear in lower human capital and rural contexts, while still being supported by community participation. The estimation of our panel data model confirm that households are more likely to have higher family assets if situated in urban area, the higher the education level, the larger the assets, and running a business increase the likelihood of having larger assets. This is especially true for non farm businesses that have a clearly larger and more significant effect on assets than farm businesses. Finally, social capital in the form of community participation also has a positive effect on assets. Those results confirm the existence of a strong entrepreneurship culture among Indonesian households. Investigating survival rates also shows that those businesses are quite stable, even in the face of a violent crisis such as the 1997 one, and as a result, can provide a safety net. Finally, considering household assets - the returns of business to the household, rather than profit or productivity - the returns of business to itself, shows that households running a business are better off. While we demonstrate that uman and social capital are key to business existence, survival and performance, those results open avenues for further research regarding the factors that could hamper growth of those businesses in terms of output and employment.

Corruption and political interest : empirical evidence at the micro level

The topic of corruption has recently attracted a great deal of attention, yet there is still a lack of micro level empirical evidence regarding the determinates of corruption. Furthermore, the present literature has not investigated the effects of political interest on corruption despite the interesting potential of this link. We address these deficiencies by analysing a cross-section of individuals, using the World Values Survey. We explore the determinants of corruption through two dependant variables (perceived corruption and the justifiability of corruption). The impact of political interest on corruption is explored through three different proxies presenting empirical evidence at both the cross-country level and the within-country level.The results of the multivariate analysis suggest that political interest has an impact on corruption controlling for a huge number of factors.

Chemical functionalities of high and low sulfur Australian coals : a case study using micro attenuated total reflectance–fourier transform infrared (ATR–FTIR) spectrometry

The macerals in bituminous coals with varying organic sulfur content from the Early Permian Greta Coal Measures at three locations (Southland Colliery, Drayton Colliery and the Cranky Corner Basin), in and around the Sydney Basin (Australia), have been studied using light-element electron microprobe (EMP) analysis and micro-ATR–FTIR. Electron microprobe analysis of individual macerals reveals that the vitrinite in both the Cranky Corner Basin and Drayton Colliery (Puxtrees seam) samples have similar carbon contents (ca. 78% C in telocollinite), suggesting that they are of equivalent rank. However, the Cranky Corner coals have anomalously low vitrinite reflectance (down to 0.45%) vs. the Drayton materials (ca. 0.7%). They also have very high organic S content (3–6.5%) and lower O content (ca. 10%) than the equivalent macerals in the Drayton sample (0.7% S and 15.6% O). A study was carried out to investigate the impacts of the high organic S on the functional groups of the macerals in these two otherwise iso-rank, stratigraphically-equivalent seams. An iso-rank low-S coal from the overlying Wittingham Coal Measures near Muswellbrook and coals of slightly higher rank from the Greta Coal Measures at Southland Colliery near Cessnock were also evaluated using the same techniques to extend the data set. Although the telocollinite in the Drayton and Cranky Corner coals have very similar carbon content (ca.78% C), the ATR–FTIR spectra of the vitrinite and inertinite macerals in these respectively low S and high S coals show some distinct differences in IR absorbance from various aliphatic and aromatic functional groups. The differences in absorbance of the aliphatic stretching bands (2800–3000 cm−1) and the aromatic carbon (CC) peak at 1606 cm−1 are very obvious. Compared to that of the Drayton sample (0.7% S and 15% O), the telocollinite of the Cranky Corner coal (6% S and 10% O) clearly shows: (i) less absorbance from OH groups, represented by a broad region around 3553 cm−1, (ii) much stronger aliphatic C–H absorbance (stretching modes around 3000–2800 cm−1 and bending modes around 1442 cm−1) and (iii) less absorbance from aromatic carbon functional groups (peaking at 1606 cm−1). Evaluation of the iso-rank Drayton and Cranky Corner coals shows that: (i) the aliphatic C–H absorbances decrease with increasing oxygen content but increase with increasing organic S content and (ii) the aromatic H to aliphatic H ratio (Har/Hali) for the telocollinite increases with (organic) O%, but decreases progressively with increasing organic S. The high organic S content in the maceral appears to be accompanied by a greater proportion of aliphatic functional groups, possibly as a result of some of the O within maceral ring structures in the high S coal samples being replaced.

Development of a multi-scale finite element model of the osteoporotic lumbar vertebral body for the investigation of apparent level vertebra mechanics and micro-level trabecular mechanics.

Osteoporotic spinal fractures are a major concern in ageing Western societies. This study develops a multi-scale finite element (FE) model of the osteoporotic lumbar vertebral body to study the mechanics of vertebral compression fracture at both the apparent (whole vertebral body) and micro-structural (internal trabecular bone core)levels. Model predictions were verified against experimental data, and found to provide a reasonably good representation of the mechanics of the osteoporotic vertebral body. This novel modelling methodology will allow detailed investigation of how trabecular bone loss in osteoporosis affects vertebral stiffness and strength in the lumbar spine.

Application of micro CT and computation modeling in bone tissue engineering

Computer aided technologies, medical imaging, and rapid prototyping has created new possibilities in biomedical engineering. The systematic variation of scaffold architecture as well as the mineralization inside a scaffold/bone construct can be studied using computer imaging technology and CAD/CAM and micro computed tomography (CT). In this paper, the potential of combining these technologies has been exploited in the study of scaffolds and osteochondral repair. Porosity, surface area per unit volume and the degree of interconnectivity were evaluated through imaging and computer aided manipulation of the scaffold scan data. For the osteochondral model, the spatial distribution and the degree of bone regeneration were evaluated. In this study the versatility of two softwares Mimics (Materialize), CTan and 3D realistic visualization (Skyscan) were assessed, too.

Adapting a generic BEAMnrc model of the BrainLAB m3 micro-multileaf collimator to simulate a local collimation device

This work is focussed on developing a commissioning procedure so that a Monte Carlo model, which uses BEAMnrc’s standard VARMLC component module, can be adapted to match a specific BrainLAB m3 micro-multileaf collimator (μMLC). A set of measurements are recommended, for use as a reference against which the model can be tested and optimised. These include radiochromic film measurements of dose from small and offset fields, as well as measurements of μMLC transmission and interleaf leakage. Simulations and measurements to obtain μMLC scatter factors are shown to be insensitive to relevant model parameters and are therefore not recommended, unless the output of the linear accelerator model is in doubt. Ultimately, this note provides detailed instructions for those intending to optimise a VARMLC model to match the dose delivered by their local BrainLAB m3 μMLC device.

Mathematically defined tissue engineering scaffold architectures prepared by stereolithography

The technologies employed for the preparation of conventional tissue engineering scaffolds restrict the materials choice and the extent to which the architecture can be designed. Here we show the versatility of stereolithography with respect to materials and freedom of design. Porous scaffolds are designed with computer software and built with either a poly(d,l-lactide)-based resin or a poly(d,l-lactide-co-ε-caprolactone)-based resin. Characterisation of the scaffolds by micro-computed tomography shows excellent reproduction of the designs. The mechanical properties are evaluated in compression, and show good agreement with finite element predictions. The mechanical properties of scaffolds can be controlled by the combination of material and scaffold pore architecture. The presented technology and materials enable an accurate preparation of tissue engineering scaffolds with a large freedom of design, and properties ranging from rigid and strong to highly flexible and elastic.

Organ printing

Organ printing techniques offer the potential to produce living 3D tissue constructs to repair or replace damaged or diseased human tissues and organs. Using these techniques, spatial variations along multiple axes with high geometric complexity can be obtained.. The level of control offered by these technologies to develop printed tissues will allow tissue engineers to better study factors that modulate tissue formation and function, and provide a valuable tool to study the effect of anatomy on graft performance. In this chapter we discuss the history behind substrate patterning and cell and organ printing, and the rationale for developing organ printing techniques with respect to limitations of current clinical tissue engineering strategies to effectively repair damaged tissues. We discuss current 2-dimensional and 3-dimesional strategies for assembling cells as well as the necessary support materials such as hydrogels, bioinks and natural and synthetic polymers adopted for organ printing research. Furthermore, given the current state-of-the-art in organ printing technologies, we discuss some of their limitations and provide recommendations for future developments in this rapidly growing field.

A review of rapid prototyping techniques for tissue engineering purposes

Rapid prototyping (RP) is a common name for several techniques, which read in data from computer-aided design (CAD) drawings and manufacture automatically threedimensional objects layer-by-layer according to the virtual design. The utilization of RP in tissue engineering enables the production of three-dimensional scaffolds with complex geometries and very fine structures. Adding micro- and nanometer details into the scaffolds improves the mechanical properties of the scaffold and ensures better cell adhesion to the scaffold surface. Thus, tissue engineering constructs can be customized according to the data acquired from the medical scans to match the each patient’s individual needs. In addition RP enables the control of the scaffold porosity making it possible to fabricate applications with desired structural integrity. Unfortunately, every RP process has its own unique disadvantages in building tissue engineering scaffolds. Hence, the future research should be focused into the development of RP machines designed specifically for fabrication of tissue engineering scaffolds, although RP methods already can serve as a link between tissue and engineering.

Is providing micro-credit social responsible?

Micro-finance, which includes micro-credit as one it its services, has become big business with a range of models – from those that operate on a strictly business basis to those who come from a philanthropic base, through Non Government organisations (NGOs). Success is often measured by the numbers involved and the repayment rates – which are very high, largely because of the lending models used. The purpose of this paper is to identify whether the means used to deliver micro-credit services to the poor are socially responsible. This paper will explore the range of models currently used and propose a model that addresses some of the social responsibility issues that appear to plague delivery. The model is being developed in Beira, the second largest city in Mozambique. Mozambique exhibits many of the characteristics found in other African countries, so the model, if successful, may have implications for other poor African nations.