SOI sensing technologies for harsh environment

This paper reviews and addresses certain aspects of Silicon-On-Insulator (SOI) technologies for a harsh environment. The paper first describes the need for specialized sensors in applications such as (i) domestic and other small-scale boilers, (ii) CO2 Capture and Sequestration, (iii) oil & gas storage and transportation, and (iv) automotive. We describe in brief the advantages and special features of SOI technology for sensing applications requiring temperatures in excess of the typical bulk silicon junction temperatures of 150oC. Finally we present the concepts, structures and prototypes of simple and smart micro-hotplate and Infra Red (IR) based emitters for NDIR (Non Dispersive IR) gas sensors in harsh environments. © 2012 IEEE.

Multi-channel effect of condensation flow in a micro triple-channel condenser

Multi-channel effect is important to understand transport phenomenon in phase change systems with parallel channels. In this paper, visualization studies were performed to study the multi-channel effect in a silicon triple-channel condenser with an aspect ratio of 0.04. Saturated water vapor was pumped into the microcondenser, which was horizontally positioned. The condenser was cooled by the air natural convention heat transfer in the air environment. Flow patterns are either the annular flow at high inlet vapor pressures, or a quasi-stable elongated bubble at the microchannel upstream followed by a detaching or detached miniature bubble at smaller inlet vapor pressures. The downstream miniature bubble was detached from the elongated bubble tip induced by the maximum Weber number there. It is observed that either a single vapor thread or dual vapor threads are at the front of the elongated bubble. A miniature bubble is fully formed by breaking up the vapor thread or threads. The transient vapor thread formation and breakup process is exactly symmetry against the centerline of the center channel. In side channels, the Marangoni effect induced by the small temperature variation over the channel width direction causes the vapor thread formation and breakup process deviating from the side channel centerline and approaching the center channel. The Marangoni effect further forces the detached bubble to rotate and approach the center channel, because the center channel always has higher temperatures, indicating the multi-channel effect. 

Two-dimensional numerical simulations of shock waves in micro convergent-divergent nozzles

The steady two-dimensional Navier-Stokes equations with the slip wall boundary conditions were used to simulate the supersonic flow in micro convergent-divergent nozzles. It is observed that shock waves can take place inside or outside of the micronozzles under the earth environment. For the over-expanded flows, there is a boundary layer separation point, downstream of which a wave interface separates the viscous boundary layer with back air flow and the inviscid core flow. The oblique shock wave is followed by the bow shock and shock diamond. The viscous boundary layer thickness relative to the whole nozzle width on the exit plane is increased but attains the maximum value around of 0.5 and oscillates against this value with the continuous increasing of the nozzle upstream pressures. The viscous effect either changes the normal shock waves outside of the nozzle for the inviscid flow to the oblique shock waves inside the nozzle, or transfers the expansion jet flow without shock waves for the inviscid flow to the oblique shock waves outside of the nozzle. 

Thermal performance of a micro-combustor for micro-gas turbine system

Premixed combustion of hydrogen gas and air was performed in a stainless steel based micro-annular combustor for a micro-gas turbine system. Micro-scale combustion has proved to be stable in the micro-combustor with a gap of 2 mm. The operating range of the micro-combustor was measured, and the maximum excess air ratio is up to 4.5. The distribution of the outer wall temperature and the temperature of exhaust gas of the micro-conbustor with excess air ratio were obtained, and the wall temperature of the micro-combustor reaches its maximum value at the excess air ratio of 0.9 instead of 1 (stoichiometric ratio). The heat loss of the micro-combustor to the environment was calculated and even exceeds 70% of the total thermal power computed from the consumed hydrogen mass flow rate. Moreover, radiant hunt transfer covers a large fraction of the total heat loss. Measures used to reduce the heat loss were proposed to improve the thermal performance of the micro-combustor. The optimal operating status of the micro-combustor and micro-gas turbine is analyzed and proposed by analyzing the relationship of the temperature of the exhaust gas of the micro-combustor with thermal power and excess air ratio. The investigation of the thermal performance of the micro-combustor is helpful to design an improved microcombustor.

Macro-Micro Modelling Analysis for High Density Packaged Flip Chips

A wide range of flip chip technologies with solder or adhesives have become dominant solutions for high density packaging applications due to the excellent electrical performance, high I/O density and good thermal performance. This paper discusses the use of modeling technique to predict the reliability of high density packaged flip chips in the humid environment. Reliability assessment is discussed for flip chip package at ultra-fine pitch with anisotropic conductive film (ACF). The purpose of this modeling work is to understand the role that moisture plays in the failure of ACF flip chips. A macro-micro 3D finite element modeling technique was used in order to make the multi-length-scale modeling of the ACF flip chip possible. Modeling results are consistent with the findings in the experimental work

Macro-micro modelling of moisture induced stresses in an ACF flip chip assembly

Purpose – This paper discusses the use of modelling techniques to predict the reliability of an anisotropic conductive film (ACF) flip chip in a humid environment. The purpose of this modelling work is to understand the role that moisture plays in the failure of ACF flip chips. Design/methodology/approach – A 3D macro-micro finite element modelling technique was used to determine the moisture diffusion and moisture-induced stresses inside the ACF flip chip. Findings – The results show that the ACF layer in the flip chip can be expected to be fully saturated with moisture after 3?h at 121°C, 100%RH, 2?atm test conditions. The swelling effect of the adhesive due to this moisture absorption causes predominately tensile stress at the interface between the adhesive and the metallization, which could cause a decrease in the contact area, and therefore an increase in the contact resistance. Originality/value – This paper introduces a macro-micro modelling technique which enables more detailed 3D modelling analysis of an ACF flip chip than previously.

Fine scale variability in methanol uptake and oxidation in the micro-layer and near-surface waters of the Atlantic

The aim of this research was to make the first depth profiles of the microbial assimilation of methanol carbon and its oxidation to carbon dioxide and use as an energy source from the microlayer to 1000 m. Some of the highest reported methanol oxidation rate constants of 0.5–0.6 d−1 were occasionally found in the microlayer and immediately underlying waters (10 cm depth), albeit these samples also showed the greatest heterogeneity compared to other depths down to 1000 m. Methanol uptake into the particulate phase was exceptionally low in microlayer samples, suggesting that any methanol utilised by microbes in this environment is for energy generation. The sea surface microlayer and 10 cm depth also showed a higher proportion of bacteria with a low DNA content, and bacterial leucine uptake rates in surface microlayer samples were either less than or the same as those in the underlying 10 cm layer. The average methanol oxidation and particulate rates were however statistically the same throughout the depths sampled, although the latter were highly variable in the near-surface 0.25–2 m compared to deeper depths. The statistically significant relationship demonstrated between uptake of methanol into particles and bacterial leucine incorporation suggests that many heterotrophic bacteria could be using methanol carbon for cellular growth. On average, methanol bacterial growth efficiency (BGEm) in the top 25 m of the water column is 6% and decreases with depth. Although, for microlayer and 10 cm-depth samples, BGEm is less than the near-surface 25–217 cm, possibly reflecting increased environmental UV stress resulting in increased maintenance costs, i.e. energy required for survival. We conclude that microbial methanol uptake rates, i.e. loss from seawater, are highly variable, particularly close to the seawater surface, which could significantly impact upon seawater concentrations and hence the air–sea flux.

Temporal variability in total, micro- and nano-phytoplankton primary production at a coastal site in the Western English Channel

Primary productivity and subsequent carbon cycling in the coastal zone have a significant impact on the global carbon budget. It is currently unclear how anthropogenic activity could alter these budgets but long term coastal time series of hydrological, biogeochemical and biological measurements represent a key means to better understand past drivers, and hence to predicting future seasonal and inter-annual variability in carbon fixation in coastal ecosystems. An 8-year time series of primary production from 2003 to 2010, estimated using a recently developed absorption-based algorithm, was used to determine the nature and extent of change in primary production at a coastal station (L4) in the Western English Channel (WEC). Analysis of the seasonal and inter-annual variability in production demonstrated that on average, nano- and pico-phytoplankton account for 48% of the total carbon fixation and micro-phytoplankton for 52%. A recent decline in the primary production of nano- and pico-phytoplankton from 2005 to 2010 was observed, corresponding with a decrease in winter nutrient concentrations and a decrease in the biomass of Phaeocystis sp. Micro-phytoplankton primary production (PPM) remained relatively constant over the time series and was enhanced in summer during periods of high precipitation. Increases in sea surface temperature, and decreases in wind speeds and salinity were associated with later spring maxima in PPM. Together these trends indicate that predicted increases in temperature and decrease in wind speeds in future would drive later spring production whilst predicted increases in precipitation would also continue these blooms throughout the summer at this site.

School as ‘Micro-city’ for the Autism Spectrum Disorder (ASD) Pupil

As architects and designers we have a responsibility to provide an inclusive built environment. For the person with Autistic Spectrum Disorder (ASD) however, the built environment can be a frightening and confusing place, difficult to negotiate and tolerate. The challenge of integrating more fully into society is denied by both having difficulty in communication and in an alienating built environment. The following paper therefore firstly outlines the challenge when designing for those with ASD. It then illustrates, by critically examining the school as a 'micro-city' (Hertzberger 2008) that a voice can be given to those with ASD. It then goes onto highlight, through two case studies in an Irish context, some of the lessons that can be learnt from pupils with ASD that are applicable to the city beyond. Finally in conclusion it suggests some of the benefits for an enriched built environment for all, when listening to the pupil with ASD. The objective is twofold; firstly to gain a better understanding of the needs of those with ASD and secondly, to ascertain what can be learnt from those with ASD that can challenge our perception of not just school, but also of the city.

Micro-organic compounds in the Humber rivers

The concentrations of a range of micro-organic compounds in the Humber rivers have been measured at weekly intervals over a period of 1 year. The compounds include the triazine herbicides (simazine, atrazine, propazine, desmetryn and prometryn), selected organophosphorus insecticides (fenitrothion, malathion and parathion), phenylurea (chlorotoluron, diuron, isoproturon and linuron) and phenoxyacid herbicides (2,4-D, MCPA, MCPB and mecoprop), phenol derivatives (phenol, 2-ethylphenol, 2-chlorophenol, 4-nitrophenol, 2-methylphenol, 4-ethylphenol and 2,4-dichlorophenol), organochlorine insecticides (HEOD, DDT, TDE, DDE, HCB, alpha-BHC and lindane), PCB's and some synthetic pyrethroid insecticides (cis/trans-permethrin, fenvalerate and cypermethrin). The results indicate the high frequency of occurrence of many compounds in the southern Humber rivers Aire, Calder, Trent and Don compared with the more occasional concentrations found in the upland rivers with catchments dominated by low intensity agriculture. The more water soluble herbicides, atrazine, simazine, isoproturon and diuron are detected frequently in the southern rivers with the highest concentrations and abundance in the rivers Aire, Calder and Trent. The most abundant phenolic compound is 2,4-dichlorophenol usually occurring at concentrations <1 mu g/l. The organochlorine insecticides and PCB's are generally at concentrations <0.01 mu g/l, cis/trans-permethrin are the only synthetic pyrethroids detected and these are found in the rivers Aire and Calder at about equal concentrations of between 0.01 and 0.11 mu g/l. The results of the occurrence of simazine and atrazine in the rivers Trent, Don and Aire illustrate peaks in concentration in the spring and then later in the year during the early autumn coinciding with the first major storm after the summer. In the rivers Trent and Don, the annual exports (March 1994-95) of atrazine are lower than for simazine whereas in the R. Calder the yield of atrazine is higher than for simazine suggesting differences in use in these catchments. The maximum triazine concentration observed, i.e. 8 mu g/l of atrazine in the R. Calder, could have inhibiting effects on the phytoplankton and algal growth, although because of the transient nature of the peaks, recovery is expected to be rapid. The only other compounds measured at concentrations likely to produce detrimental ecotoxicological effects are cis/trans permethrin in the rivers Aire and Calder. (C) 1997 Elsevier Science B.V.

Influence of micro and macro cracks due to sustained loading on chloride-induced corrosion of reinforced concrete beams

Chloride-induced corrosion of steel is one of the most commonly found problems affecting the durability of reinforced concrete structures in both marine environment and where de-icing salt is used in winter. As the significance of micro-cracks on chloride induced corrosion is not well documented, 24 reinforced concrete beams (4 different mixes - one containing Portland cement and another containing 35% ground granulated blastfurnace slag at 0.45 and 0.65 water-binder ratios) were subjected to three levels of sustained lateral loading (0%, 50% and 100% of the load that can induce 0.1 mm wide cracks on the tension surface of beam - F_0.1) in this work. The beams were then subjected to weekly cycles of wetting with 10% NaCl solution for 1 day followed by 6 days of drying at 20 (±1) °C up to an exposure period of 60 weeks. The progress of corrosion of steel was monitored using half-cell potential apparatus and linear polarisation resistance (LPR) test. These results have shown that macro-cracks (at load F_0.1) and micro-cracks (at 50% of F_0.1) greatly accelerated both the initiation and propagation stages of the corrosion of steel in the concrete beams. Lager crack widths for the F_0.1 load cases caused higher corrosion rates initially, but after about 38 weeks of exposure, there was a decrease in the rate of corrosion. However, such trends could not be found in 50% F _0.1 group of beams. The extent of chloride ingress also was influenced by the load level. These findings suggest that the effect of micro-cracking at lower loads are very important for deciding the service life of reinforced concrete structures in chloride exposure environments. © 2014 4th International Conference on the Durability of Concrete Structures.

Productividad, innovación y uso de tecnologías de información y las comunicaciones (tic) como factores de desarrollo de la micro, pequeña y mediana empresa (mipyme) en Bogotá.

Las TIC han impactado en el funcionamiento de las organizaciones y han aportado a su proceso evolutivo, generando diversos efectos de acuerdo a la función que estas cumplen dentro de la organización. Las TIC como consecuencia se convierten en una estrategia de gestión en un entorno complejo donde permiten alcanzar mejoras en la organización social, la actividad económica, el bienestar y el acceso a la información y el conocimiento. (Cáceres Carrasco & Aceytuno Pérez, 2008)Con el fin de entender los beneficios de las TIC, se deben brindar a los directores herramientas que permitan formular modelos de negocios efectivos de cara a los mercados y enfocadas a la satisfacción de los clientes. Adicionalmente, para las organizaciones el añadir valor, no sólo hace referencia al servicio que están prestando; hay otros factores diferentes al uso de herramientas TIC y la innovación que también son igual de importantes como: los procesos de apoyo, de gestión que se encuentran de fondo y que hacen posible brindar un servicio al mercado, en estos procesos se encuentran aplicaciones de procedimientos amigables y fáciles de articular, temas como la responsabilidad empresarial, relación y comunicación con competidores dentro del mismo sector, es justamente en las relaciones con los clientes, que las TIC y el uso de Internet puede tener incidencia en los modelos de negocios a través de actividades como el comercio electrónico, el mercadeo electrónico, el mercadeo en línea entre otros. Existen investigaciones acerca de estos temas: innovación, TI, pero no se han establecido relaciones entre ellos, debido a su novedad. Diferentes experiencias laborales de los investigadores en el uso de las TIC como herramienta en la organización de información permiten que surja la idea de llevar a cabo este proyecto abarcando la realidad bogotana de las MiPyme. La presente investigación con un enfoque cualitativo hace una revisión bibliográfica, y bajo la mirada teórica se analiza la relación que tienen los factores de desarrollo que se evidenciaron como son la innovación y el uso de herramientas TIC, como variables dependientes de la productividad de las MiPyme en Bogotá, Colombia, involucrando temas que se relacionan con distintos campos como la tecnología, políticas gubernamentales, y economía.

Pesticides and other micro-organic contaminants in freshwater sedimentary environments - a review

A wide range of issues relating to the presence and fate of pesticides and other micro-organic contaminants (MOCs) in surface freshwater sedimentary environments is reviewed. These issues include the sources, transport and occurrence of MOCs in freshwater environments; their ecological effects; their interaction with sedimentary material; and a range of processes related to their fate, including degradation, diffusion in bed sediments, bioturbation and slow contaminant release. An emphasis is placed on those processes-chemical, physical or biological-in which sediments play a role in determining the fate of micro-organics in freshwater environments. The issues of occurrence, source and transport, and the ecological effects of micro-organics are introduced more briefly, the focus where these aspects are concerned being largely on pesticides. In the concluding section, key points and issues relating to the study of micro-organics in freshwater environments are summarised and areas where initial or further research would be welcome are highlighted. It is hoped that this paper will both form a useful reference for workers in the field of micro-organic contaminants, and also stimulate new work in the freshwater environment and beyond. (C) 2003 Elsevier Science Ltd. All rights reserved.