Thixotropic studies of lead-based solder, lead-free solder and conductive adhesive pastes

The stencil printing process is an important process in the assembly of Surface Mount Technology (SMT)devices. There is a wide agreement in the industry that the paste printing process accounts for the majority of assembly defects. Experience with this process has shown that typically over 60% of all soldering defects are due to problems associated with the flow properties of solder pastes. Therefore, the rheological measurements can be used as a tool to study the deformation or flow experienced by the pastes during the stencil printing process. This paper presents results on the thixotropic behaviour of three pastes; lead-based solder paste, lead-free solder paste and isotropic conductive adhesive (ICA). These materials are widely used as interconnect medium in the electronics industry. Solder paste are metal alloys suspended in a flux medium while the ICAs consist of silver flakes dispersed in an epoxy resin. The thixotropy behaviour was investigated through two rheological test; (i) hysteresis loop test and (ii) steady shear rate test. In the hysteresis loop test, the shear rate were increased from 0.001 to 100s-1 and then decreased from 100 to 0.001s-1. Meanwhile, in the steady shear rate test, the materials were subjected to a constant shear rate of 0.100, 100 and 0.001s-1 for a period of 240 seconds. All the pastes showed a high degree of shear thinning behaviour with time. This might be due to the agglomeration of particles in the flux or epoxy resin that prohibits pastes flow under low shear rate. The action of high shear rate would break the agglomerates into smaller pieces which facilitates the flow of pastes, thus viscosity is reduced at high shear rate. The solder pastes exhibited a higher degree of structural breakdown compared to the ICAs. The area between the up curve and down curve in the hysteresis curve is an indication of the thixotropic behavior of the pastes. Among the three pastes, lead-free solder paste showed the largest area between the down curve and up curve, which indicating a larger structural breakdown in the pastes, followed by lead-based solder paste and ICA. In a steady shear rate test, viscosity of ICA showed the best recovery with the steeper curve to its original viscosity after the removal of shear, which indicating that the dispersion quality in ICA is good because the high shear has little effect on the microstructure of ICA. In contrast, lead-based paste showed the poorest recovery which means this paste undergo larger structural breakdown and dispersion quality in this paste is poor because the microstructure of the paste is easily disrupted by high shear. The structural breakdown during the application of shear and the recovery after removal of shear is an important characteristic in the paste printing process. If the paste’s viscosity can drop low enough, it may contribute to the aperture filling and quick recovery may prevent slumping.

Low power field programmable gate array implementation of fast digital signal processing algorithms: characterisation and manipulation of data locality

Dynamic power consumption is very dependent on interconnect, so clever mapping of digital signal processing algorithms to parallelised realisations with data locality is vital. This is a particular problem for fast algorithm implementations where typically, designers will have sacrificed circuit structure for efficiency in software implementation. This study outlines an approach for reducing the dynamic power consumption of a class of fast algorithms by minimising the index space separation; this allows the generation of field programmable gate array (FPGA) implementations with reduced power consumption. It is shown how a 50% reduction in relative index space separation results in a measured power gain of 36 and 37% over a Cooley-Tukey Fast Fourier Transform (FFT)-based solution for both actual power measurements for a Xilinx Virtex-II FPGA implementation and circuit measurements for a Xilinx Virtex-5 implementation. The authors show the generality of the approach by applying it to a number of other fast algorithms namely the discrete cosine, the discrete Hartley and the Walsh-Hadamard transforms.

Using smart people to form future mobile wireless networks

The concept of a body-to-body network, where smart communicating devices carried or worn by a person are used to form a wireless network with devices situated on other nearby persons. New innovations in this area will see the form factor of smart devices being modified, so that they may be worn on the human body or integrated into clothing, in the process creating a new generation of smart people. Applications of body-to-body networking will extend well beyond the support of cellular and Wi-Fi networks. They will also be used in short-range covert military applications, first responder applications, team sports and used to interconnect body area networks (BAN). Security will be a major issue as routing between multiple nodes will increase the risk of unauthorized access and compromise sensitive data. This will add complexity to the medium access layer (MAC) and network management. Antennas designed to operate in body centric communications systems may be broadly categorized as on- or off-body radiators, according to their radiation pattern characteristics when mounted on the human body.

Efficient advanced encryption standard implementation using lookup and normal basis

A new type of advanced encryption standard (AES) implementation using a normal basis is presented. The method is based on a lookup technique that makes use of inversion and shift registers, which leads to a smaller size of lookup for the S-box than its corresponding implementations. The reduction in the lookup size is based on grouping sets of inverses into conjugate sets which in turn leads to a reduction in the number of lookup values. The above technique is implemented in a regular AES architecture using register files, which requires less interconnect and area and is suitable for security applications. The results of the implementation are competitive in throughput and area compared with the corresponding solutions in a polynomial basis.

Millimeter-wave communications for 5G: fundamentals: Part I [Guest Editorial]

The widespread availability and demand for multimedia capable devices and multimedia content have fueled the need for high-speed wireless connectivity beyond the capabilities of existing commercial standards. While fiber optic data transfer links can provide multigigabit- per-second data rates, cost and deployment are often prohibitive in many applications. Wireless links, on the contrary, can provide a cost-effective fiber alternative to interconnect the outlining areas beyond the reach of the fiber rollout. With this in mind, the ever increasing demand for multi-gigabit wireless applications, fiber segment replacement mobile backhauling and aggregation, and covering the last mile have posed enormous challenges for next generation wireless technologies. In particular, the unbalanced temporal and geographical variations of spectrum usage along with the rapid proliferation of bandwidth- hungry mobile applications, such as video streaming with high definition television (HDTV) and ultra-high definition video (UHDV), have inspired millimeter-wave (mmWave) communications as a promising technology to alleviate the pressure of scarce spectrum resources for fifth generation (5G) mobile broadband.

High-radix systolic modular multiplication on reconfigurable hardware

The overall aim of the work presented in this paper has been to develop Montgomery modular multiplication architectures suitable for implementation on modern reconfigurable hardware. Accordingly, novel high-radix systolic array Montgomery multiplier designs are presented, as we believe that the inherent regular structure and absence of global interconnect associated with these, make them well-suited for implementation on modern FPGAs. Unlike previous approaches, each processing element (PE) comprises both an adder and a multiplier. The inclusion of a multiplier in the PE means that the need to pre-compute or store any multiples of the operands is avoided. This also allows very high-radix implementations to be realised, further reducing the amount of clock cycles per modular multiplication, while still maintaining a competitive critical delay. For demonstrative purposes, 512-bit and 1024-bit FPGA implementations using radices of 2(8) and 2(16) are presented. The subsequent throughput rates are the fastest reported to date.

Diversidade linguística e educação para um futuro sustentável: que potencialidades nos primeiros anos de escolaridade?

Este estudo pretende analisar as relações entre a educação para a sustentabilidade e a sensibilização à diversidade linguística e cultural no currículo dos primeiros anos de escolaridade através do desenvolvimento de um projeto de intervenção pedagógico-didática. Para tal, refletiu-se sobre as noções de educação para o desenvolvimento sustentável e de sensibilização à diversidade linguística e cultural, explicitando o modo como se podem cruzar. Com este enquadramento, e numa lógica de investigação-ação, desenvolveuse o projeto de intervenção “Do meu mundo vejo o outro e o seu mundo”, em 21 sessões, numa turma do 4º ano do 1º Ciclo do Ensino Básico, de forma colaborativa com a respetiva professora titular, numa escola do distrito de Aveiro, durante o ano letivo de 2008/2009. Recolheram-se dados através da observação direta do(a)s aluno(a)s durante as sessões e de inquéritos por questionário e por entrevista ao(à)s aluno(a)s e à professora participante. Os dados recolhidos durante as sessões foram analisados com recurso à Escala de nível de envolvimento de Leuven (Laevers, 1994) e os inquéritos por questionário e entrevista foram alvo de uma análise estatística descritiva e de uma análise de conteúdo. Identificaram-se os efeitos do projeto no(a)s aluno(a)s em termos do seu nível de envolvimento nas atividades e do desenvolvimento das suas atitudes, conhecimentos e capacidades. A partir das vozes dos participantes, analisouse ainda a apreciação que realizaram do projeto na sua globalidade. Os resultados da análise apontam no sentido de que o projeto de intervenção desenvolvido contribuiu para: ajudar a derrubar barreiras disciplinares entre as àreas do currículo; justificar a necessidade de contemplar a sensibilização à diversidade linguística e cultural em processos de educação para o desenvolvimento sustentável; desenvolver materiais didáticos diversificados construídos numa lógica interdisciplinar, reconhecidos pela professora como inovadores e importantes para aprendizagens significativas e contextualizadas; transformar atitudes do(a)s aluno(a)s face à diversidade e à sustentabilidade, na preparação para uma cidadania planetária; e desenvolver no(a)s aluno(a)s uma consciência sistémica evidenciada na capacidade de relacionamento do global e do local em temas de diferentes áreas do conhecimento. Este estudo apresenta um conjunto de argumentos para a integração do tratamento da diversidade linguística e cultural no quadro de uma educação para um futuro mais sustentável nos primeiros anos de escolaridade, pela consideração de quatro grandes preocupações educativas: educar para compreender o mundo, educar para agir no mundo; educar para conviver com os outros e educar para o nunca-mais.

Alkaline-earth aluminosilicate-based glass and glass-ceramic sealants for functional applications

The planar design of solid oxide fuel cell (SOFC) is the most promising one due to its easier fabrication, improved performance and relatively high power density. In planar SOFCs and other solid-electrolyte devices, gas-tight seals must be formed along the edges of each cell and between the stack and gas manifolds. Glass and glass-ceramic (GC), in particular alkaline-earth alumino silicate based glasses and GCs, are becoming the most promising materials for gas-tight sealing applications in SOFCs. Besides the development of new glass-based materials, new additional concepts are required to overcome the challenges being faced by the currently existing sealant technology. The present work deals with the development of glasses- and GCs-based materials to be used as a sealants for SOFCs and other electrochemical functional applications. In this pursuit, various glasses and GCs in the field of diopside crystalline materials have been synthesized and characterized by a wide array of techniques. All the glasses were prepared by melt-quenching technique while GCs were produced by sintering of glass powder compacts at the temperature ranges from 800−900 ºC for 1−1000 h. Furthermore, the influence of various ionic substitutions, especially SrO for CaO, and Ln2O3 (Ln=La, Nd, Gd, and Yb), for MgO + SiO2 in Al-containing diopside on the structure, sintering and crystallization behaviour of glasses and properties of resultant GCs has been investigated, in relevance with final application as sealants in SOFC. From the results obtained in the study of diopside-based glasses, a bilayered concept of GC sealant is proposed to overcome the challenges being faced by (SOFCs). The systems designated as Gd−0.3 (in mol%: 20.62MgO−18.05CaO−7.74SrO−46.40SiO2−1.29Al2O3 − 2.04 B2O3−3.87Gd2O3) and Sr−0.3 (in mol%: 24.54 MgO−14.73 CaO−7.36 SrO−0.55 BaO−47.73 SiO2−1.23 Al2O3−1.23 La2O3−1.79 B2O3−0.84 NiO) have been utilized to realize the bi-layer concept. Both GCs exhibit similar thermal properties, while differing in their amorphous fractions, revealed excellent thermal stability along a period of 1,000 h. They also bonded well to the metallic interconnect (Crofer22APU) and 8 mol% yttrium stabilized zirconium (8YSZ) ceramic electrolyte without forming undesirable interfacial layers at the joints of SOFC components and GC. Two separated layers composed of glasses (Gd−0.3 and Sr−0.3) were prepared and deposited onto interconnect materials using a tape casting approach. The bi-layered GC showed good wetting and bonding ability to Crofer22APU plate, suitable thermal expansion coefficient (9.7–11.1 × 10–6 K−1), mechanical reliability, high electrical resistivity, and strong adhesion to the SOFC componets. All these features confirm the good suitability of the investigated bi-layered sealant system for SOFC applications.

Broadband Green's Function and Applications to Fast Electromagnetic Analysis of High-Speed Interconnects

Thesis (Ph.D.)--University of Washington, 2015

Supporting real-time distributed computer-controlled systems with multi-hop P-NET networks

Fieldbus communication networks aim to interconnect sensors, actuators and controllers within process control applications. Therefore, they constitute the foundation upon which real-time distributed computer-controlled systems can be implemented. P-NET is a fieldbus communication standard, which uses a virtual token-passing medium-access-control mechanism. In this paper pre-run-time schedulability conditions for supporting real-time traffic with P-NET networks are established. Essentially, formulae to evaluate the upper bound of the end-to-end communication delay in P-NET messages are provided. Using this upper bound, a feasibility test is then provided to check the timing requirements for accessing remote process variables. This paper also shows how P-NET network segmentation can significantly reduce the end-to-end communication delays for messages with stringent timing requirements.

Interaction of malaria parasites with host late endocytic and autophagic pathways is essential for Plasmodium liver stage development

RESUMO: A Malária é causada por parasitas do género Plasmodium, sendo a doença parasitária mais fatal para o ser humano. Apesar de, durante o século passado, o desenvolvimento económico e a implementação de diversas medidas de controlo, tenham permitido erradicar a doença em muitos países, a Malária continua a ser um problema de saúde grave, em particular nos países em desenvolvimento. A Malária é transmitida através da picada de uma fêmea de mosquito do género Anopheles. Durante a picada, os esporozoítos são injetados na pele do hospedeiro, seguindo-se a fase hepática e obrigatória do ciclo de vida. No fígado, os esporozoítos infetam os hepatócitos onde se replicam, dentro de um vacúolo parasitário (VP) e de uma forma imunitária silenciosa, em centenas de merozoitos. Estas novas formas do parasita são as responsáveis por infetar os eritrócitos, iniciando a fase sanguínea da doença, onde se os primeiros sintomas se manifestam, tais como a característica febre cíclica. A fase hepática da doença é a menos estudada e compreendida. Mais ainda, as interações entre o VP e os organelos da células hospedeira estão ainda pouco caracterizados. Assim, neste estudo, as interações entre os organelos endocíticos e autofágicos da célula hospedeira e o VP foram dissecados, observando-se que os anfisomas, que são organelos resultantes da intersecção do dois processos de tráfego intracelular, interagem com o parasita. Descobrimos que a autofagia tem também uma importante função imunitária durante a fase hepática inicial, ao passo, que durante o desenvolvimento do parasita, já numa fase mais tardia, o parasita depende da interação com os endossomas tardios e anfisomas para crescer. Vesiculas de BSA, EGF e LC3, foram, também, observadas dentro do VP, sugerindo que os parasitas são capazes de internalizar material endocítico e autofágico do hospedeiro. Mais ainda, mostramos que esta interação depende da cinase PIKfyve, responsável pela conversão do fosfoinositidio-3-fosfato no fosfoinositidio-3,5-bifosfato, uma vez que inibindo esta cinase o parasita não é capaz de crescer normalmente. Finalmente, mostramos que a proteína TRPML1, uma proteína efetora do fosfoinositidio-3,5-bifosfato, e envolvida no processo de fusão das membranas dos organelos endocíticos e autofágicos, também é necessária para o crescimento do parasita. Desta forma, o nosso estudo sugere que a membrana do VP funde com vesiculas endocíticas e autofágicas tardias, de uma forma dependente do fositidio-3,5-bifosfato e do seu effetor TRPML1, permitindo a troca de material com a célula hospedeira. Concluindo, os nossos resultados evidenciam que o processo autofágico que ocorre na célula hospedeira tem um papel duplo durante a fase hepática da malaria. Enquanto numa fase inicial os hepatócitos usam o processo autofágico como forma de defesa contra o parasita, já durante a fase de replicação o VP funde com vesiculas autofágicas e endocíticas de forma a obter os nutrientes necessários ao seu desenvolvimento.--------- ABSTRACT: Malaria, which is caused by parasites of the genus Plasmodium, is the most deadly parasitic infection in humans. Although economic development and the implementation of control measures during the last century have erradicated the disease from many areas of the world, it remains a serious human health issue, particularly in developing countries. Malaria is transmitted by female mosquitoes of the genus Anopheles. During the mosquito blood meal, Plasmodium spp. sporozoites are injected into the skin dermis of the vertebrate host, followed by an obligatory liver stage. Upon entering the liver, Plasmodium parasites infect hepatocytes and silently replicate inside a host cell-derived parasitophorous vacuole (PV) into thousands of merozoites. These new parasite forms can infect red blood cells initiating the the blood stage of the disease which shows the characteristic febrile malaria episodes. The liver stage is the least characterized step of the malaria infection. Moreover, the interactions between the Plasmodium spp. PV and the host cell trafficking pathways are poorly understood. We dissected the interaction between Plasmodium parasites and the host cell endocytic and autophagic pathways and we found that both pathways intersect and interconnect in the close vicinity of the parasite PV, where amphisomes are formed and accumulate. Interestingly, we observed a clearance function for autophagy in hepatocytes infected with Plasmodium berghei parasites at early infection times, whereas during late liver stage development late endosomes and amphisomes are required for parasite growth. Moreover, we found the presence of internalized BSA, EGF and LC3 inside parasite vacuoles, suggesting that the parasites uptake endocytic and autophagic cargo. Furthermore, we showed that the interaction between the PV and host traffic pathways is dependent on the kinase PIKfyve, which converts the phosphoinositide PI(3)P into PI(3,5)P2, since PIKfyve inhibition caused a reduction in parasite growth. Finally, we showed that the PI(3,5)P2 effector protein TRPML1, which is involved in late endocytic and autophagic membrane fusion, is also required for parasite development. Thus, our studies suggest that the parasite parasitophorous vacuole membrane (PVM) is able to fuse with late endocytic and autophagic vesicles in a PI(3,5)P2- and TRPML1-dependent manner, allowing the exchange of material between the host cell and the parasites, necessary for the rapid development of the latter that is seen during the liver stage of infection. In conclusion, we present evidence supporting a specific and essential dual role of host autophagy during the course of Plasmodium liver infection. Whereas in the initial hours of infection the host cell uses autophagy as a cell survival mechanism to fight the infection, during the replicative phase the PV fuses with host autophagic and endocytic vesicles to obtain nutrients required for parasite growth.

Gestão de crises de âmbito policial

The issues concerning Crisis Situations under the scope of police activity, raised after incidents considered critical, has emerged with greater intensity during the most recent decades, posing a major challenge for police forces around the world. These are situations or events of crucial importance, involving hostage taken or barricaded individuals, in which inevitably human lives are at risk, requiring from law enforcement agencies a specific response capability, i.e., a type of intervention not framed under the parameters considered as routine, in order to obtain solutions to minimize the possibility of casualties. Because this is about impacting situations of extreme gravity, where the preservation of human lives is concerned and, in many cases, the very Rule of Law as well, we understand the need for police forces to adapt to new procedures and working methods. Such procedures are an enormously complex task that requires the coordination and articulation of several components, including not infrequently the performance of different police forces, as well as organizations and entities with varied powers and duties, which implies the need for effective management. This explains the emergence of Crisis Management Structures, imposing to determine which are their fundamental components, their importance, how they interconnect, and their major goal. The intrinsic features will also be analyzed in the aspect that we consider to be the fundamental groundwork of a Crisis Management Structure, i.e., Negotiation itself, considering it as a kind of police intervention, where a wide range of procedures feeds a channel of dialogue, aiming at minimizing the damage resultant from an extreme action, in particular, to prevent the death of any of those involved. This is in essence the path we have chosen to develop this study, trying to find out an answer to the fundamental question: What model of Crisis Management Structure should be adopted to manage a critical event involving hostage negotiation?

I must walk through the gate : an ontological necessity

This research is a self-study into my life as an athlete, elementary school teacher, leamer, and as a teacher educator/academic. Throughout the inquiry, I explore how my beliefs and values infused my lived experiences and ultimately influenced my constructivist, humanist, and ultimately my holistic teaching and learning practice which at times disrupted the status quo. I have written a collection of narratives (data generation) which embodied my identity as an unintelligent student/leamer, a teacher/learner, an experiential learner, a tenacious participant, and a change agent to name a few. As I unpack my stories and hermeneutically reconstruct their intent, I question their meaning as I explore how I can improve my teaching and learning practice and potentially effect positive change when instructing beginning teacher candidates at a Faculty of Education. At the outset I situate my story and provide the necessary political, social, and cultural background information to ground my research. I follow this with an in depth look at the elements that interconnect the theoretical framework of this self-study by presenting the notion of writing at the boundaries through auto ethnography (Ellis, 2000; Ellis & Bochner, 2004) and writing as a method of inquiry (Richardson, 2000). The emergent themes of experiential learning, identity, and embodied knowing surfaced during the data generation phase. I use the Probyn' s (1990) .. metaphor of locatedness to unpack these themes and ponder the question, Where is experience located? I deepen the exploration by layering Drake's (2007) KnowlDo/Be framework alongside locatedness and offer descriptions of learning moments grounded in pedagogical theories. In the final phase, I introduce thirdspace theory (Bhabha, 1994; Soja, 1996) as a space that allowed me to puzzle educational dilemmas and begin to reconcile the binaries that existed in my life both personally, and professionally. I end where I began by revisiting the questions that drove this study. In addition, Ireflect upon the writing process and the challenges that I encountered while immersed in this approach and contemplate the relevance of conducting a self-study. I leave the reader with what is waiting for me on the other side of the gate, for as Henry James suggested, "Experience is never limited, and it is never complete."

Understanding Network Governance: A Case Study Exploration of Active Canada 20/20

Consistent with the governance shift towards network forms of governance, a number of new social movements have formed in response to the declining levels of physical activity in the Western world. One such movement is Active Canada 20/20: A Physical Activity Strategy and Change Agenda for Canada. Network governance is employed as the theoretical framework for this case study exploration of Active Canada 20/20 and the political landscape surrounding its development and implementation. Semi-structured interviews were conducted in addition to document/policy analysis and direct observations. Analysis of the data resulted in three overarching themes – the defining characteristics of network governance, the political landscape, and intersectoral linkages – that interconnect multifariously based the nature of the Canadian federal government and its relationship with the voluntary sector for physical activity. Despite progress in driving Active Canada 20/20 forward, entrenched dynamics of power need to be navigated within the political landscape surrounding network governance.

Vers une intégration écologique des technologies de l’information et de la communication en éducation en Afrique du Centre et de l’Ouest : une approche culturelle

Dans un monde de plus en plus interconnecté où le développement nécessite une participation active à la société de l’information, où les différentes cultures rentrent davantage en contact entre elles et où les biens culturels sont devenus des biens de consommation, les minorités culturelles mondiales intégrant les technologies de l’information et de la communication (TIC) se retrouvent marginalisées face à la menace d’hégémonie culturelle des réseaux de l’information par les cultures dominantes de certains pays développés. Pour qu’une culture prenne sa place dans la société de l’information, il revient en premier lieu à ses institutions éducatives de former leurs apprenants dans un contexte culturel qui leur est propre et de valoriser et d’encourager la production et l’utilisation de contenu endogène. C’est dans le cadre de cette problématique que la présente recherche s’est donnée comme premier objectif de faire le bilan du contenu culturel accédé et diffusé par les TIC dans des écoles de pays africains dits en développement ; pour ensuite, comme deuxième objectif, de décrire les barrières à une intégration des TIC qui favoriserait la promotion culturelle en ligne dans ces écoles ; et finalement, comme troisième objectif, d’identifier des stratégies pragmatiques favorisant une intégration écologique des TIC dans ces écoles, c’est-à-dire, une intégration durable, adaptée au contexte local et favorisant la pleine participation des enseignants et des élèves. Pour y parvenir, nous avons adopté une approche méthodologique essentiellement descriptive et qualitative. Nous avons réalisé des entrevues avec 168 enseignants et 230 élèves de 34 écoles pionnières TIC situées dans cinq pays d’Afrique de l’Ouest et du Centre, que nous avons traitées selon une analyse de contenu spécifique à chaque objectif. L’adoption des stratégies décrites dans nos résultats permettrait aux écoles étudiées de surmonter, en partie, la multitude de barrières auxquelles elles font face et de favoriser l’intégration écologique des TIC. Une telle intégration est nécessaire à l’atteinte d’une société de l’information plus équitable et à l’éventuelle réduction du fossé numérique séparant les « info-riches » des « info-pauvres ».