Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Compósitos poliméricos a base de fibras de licuri: efeitos da hibridização e do envelhecimento ambiental acelerado

The gradual replacement of conventional materials by the ones called composite materials is becoming a concern about the response of these composites against adverse environmental conditions, such as ultraviolet radiation, high temperature and moist. Also the search for new composite using natural fibers or a blend of it with synthetic fibers as reinforcement has been studied. In this sense, this research begins with a thorough study of microstructural characterization of licuri fiber, as a proposal of alternative reinforcement to polymeric composites. Thus, a study about the development of two composite laminates was done. The first one, involving only the fiber of licuri and the second comprising a hybrid composite based of fiber glass E and the fiber of licuri, in order to know the performance of the fiber when of fiber across the hybridization process. The laminates were made in the form of plates using the tereftálica ortho-polyester resin as matrix. The composite laminate made only by licuri fiber had two reinforcing fabric layers of unidirectional licuri and the hybrid composite had two reinforcing layers of unidirectional licuri fabric and three layers of fiber short glass-E mat. Finally, both laminates was exposed to aging acceleration in order to study the influence of environmental degradation involving the mechanical properties and fracture characteristics thereof. Regarding the mechanical properties of composites, these were determined through uniaxial tensile tests, uniaxial compression and three bending points for both laminates in original state, and uniaxial tensile tests and three bending points after accelerated aging. As regards the study of structural degradation due to aging of the laminates, it was carried out based on microscopic analysis and microstructure, as well as measuring weight loss. The characteristics of the fracture was performed by macroscopic and microscopic (optical and SEM) analysis. In general, the laminated composites based on fiber licuri showed some advantages in their responses to environmental aging. These advantages are observed in the behavior related to stiffness as well as the microstructural degradation and photo-oxidation processes. However, the structural integrity of this laminate was more affected in case the action of uniaxial tensile loads, where it was noted a lower rate of withholding his last resistance property

Modificação superficial de filmes de poliéster usando plasma a baixa temperatura

A polyester film has a vast application field, due some properties that are inherent of this kind of material such as, good mechanical resistance, chemical resistance to acids and bases and low production cost. However, this material has some limitations as low superficial tension, flat surface, low affinity to dyers, and poor adhesion which impede the use of the same ones for some finality as good wettability. Among the existent techniques to increase the superficial tension, plasma as energy source is the more promising technique, because of their versatility and for not polluting the environment. The plasma surface polymeric modification has been used for many researchers, because it does not affect the environment with toxic agents, the alterations remains only at nanometric layers and this technique shows expressive results. Then, due to its good acceptance, polyester films were treated with oxygen plasma varying the treatment time from 10 to 60 min with an increase of 10 min to each subsequent treatment. Also, the samples were treated with a gas mixture (nitrogen + oxygen) varying the percentage of each gas the mixture from 0 to 100%, the treatment time remaining constant to all treatments (10 min). After plasma treatment the samples were characterized by contact angle, surface tension, Raman spectroscopy, Infrared attenuated total reflection (IR-ATR) and atomic force microscopy, with the aim to study the wettability increase of treated polyester films as its variables. In the (O2/N2) plasma treatment of polyester films can be observed an increase of superficial roughness superior to those treated by O2 plasma. By the other hand, the chemical modification through the implantation of polar groups at the surface is obtained more easily using O2 plasma treatment

Estudo da molhabilidade de tecidos 100% poliéster tratados em plasma N2/O2 em função do seu envelhecimento natural

This work reports the influence of the poly (ethylene terephthalate) textile surface modification by plasmas of O2 and mixtures (N2 + O2), on their physical and chemical properties. The treatment was carried out in a vacuum chamber. Some parameters remained constant during all treatment, such as: Voltage 470 V; Pressure 1,250 Mbar; Current: 0, 10 A and gas flow: 10 cm3/min. Other parameters, such as working gas composition and treatment time, were modified as the following: to the O2 plasma modified samples only the treatment time was changed (10, 20, 30, 40, 50 and 60 minutes). To the plasma with O2 and N2 only the chemical concentrations were changed. Through Capillary tests (vertical) an increase in textile wettability was observed as well as its influence on aging time and its consequence on wettability. The surface functional groups created after plasma treatments were investigated using X-ray Photoelectron Spectroscopy (XPS). The surface topography was examined by scanning electron microscope (SEM)

Efeito da adição do poli(etileno acrilato de metila) (ema) e da fibra de linter de algodão nas propriedades do poli(tereftalato de etileno) reciclado (petrec)

The development of new materials to fill the demand of technological advances is a challenge for many researchers around the world. Strategies such as making blends and composites are promising alternatives to produce materials with different properties from those found in conventional polymers. The objective of this study is to evaluate the effect of adding the copolymer poly(ethylene methyl acrylate) (EMA) and cotton linter fibers (LB) on the properties of recycled poly(ethylene terephthalate) (PETrec) by the development of PETrec/EMA blend and PETrec/EMA/LB blend composite. In order to improve the properties of these materials were added as compatibilizers: Ethylene - methyl acrylate - glycidyl methacrylate terpolymer (EMA-GMA) and maleic anhydride grafted polyethylene (PE-g-MA). The samples were produced using a single screw extruder and then injection molded. The obtained materials were characterized by thermogravimetry (TG), melt flow index (MFI) mensurements, torque rheometry, pycnometry to determinate the density, tensile testing and scanning electron microscopy (SEM). The rheological results showed that the addition of the EMA copolymer increased the viscosity of the blend and LB reduces the viscosity of the blend composite. SEM analysis of the binary blend showed poor interfacial adhesion between the PETrec matrix and the EMA dispersed phase, as well as the blend composite of PETrec/EMA/LB also observed low adhesion with the LB fiber. The tensile tests showed that the increase of EMA percentage decreased the tensile strength and the Young s modulus, also lower EMA percentage samples had increased the elongation at break. The blend composite showed an increase in the tensile strength and in the Young`s modulus, and a decrease in the elongation at break. The blend formulations with lower EMA percentages showed better mechanical properties that agree with the particle size analysis which showed that these formulations presented a smaller diameter of the dispersed phase. The blend composite mechanical tests showed that this material is stronger and stiffer than the blend PETrec/EMA, whose properties have been reduced due to the presence of EMA rubbery phase. The use of EMA-GMA was effective in reducing the particle size of the EMA dispersed phase in the PETrec/EMA blend and PE-g-MA showed evidences of reaction with LB and physical mixture with the EMA

Desenvolvimento e caracterização de compósito a partir da borra da piaçava para construção da parábola de um fogão solar a concentração

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Pirólise termoquímica de pós da fibra de coco seco em um reator de cilindro rotativo para produção de bio-óleo

This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.

Adsorção de cobre e cromo utilizando fibra de sisal visando o tratamento da água produzida pela indústria petrolífera

Currently, the oil industry is the biggest cause of environmental pollution. The objective was to reduce the concentration of copper and chromium in the water produced by the oil industry. It was used as adsorbent natural sisal fiber Agave sp treated with nitric acid and sodium hydroxide. All vegetable fibers have physical and morphological properties that enablies the adsorption of pollutants. The basic composition of sisal is cellulose, hemicellulose and lignin. The features are typically found in the characterization of vegetable fibers, except the surface area that was practically zero. In the first stage of adsorption, it was evaluated the effect of temperature and time skeeking to optimize the execution of the factorial design. The results showed that the most feasible fiber was the one treated with acid in five hours (30°C). The second phase was a factorial design, using acid and five hours, this time was it determined in the first phase. The tests were conducted following the experimental design and the results were analyzed by statistical methods in order to optimize the main parameters that influence the process: pH, concentration (mol / L) and fiber mass/ metal solution volume. The volume / mass ratio factor showed significant interference in the adsorption process of chromium and copper. The results obtained after optimization showed that the highest percentages of extraction (98%) were obtained on the following operating conditions: pH: 5-6, Concentration: 100 ppm and mass/ volume: 1 gram of fiber/50mL solution. The results showed that the adsorption process was efficient to remove chromium and copper using sisal fibers, however, requiring further studies to optimize the process.

Períodos de interferência das plantas daninhas em algodoeiro de fibra colorida ‘BRS Safira’

This study aimed to determine the late-season presence of weeds in reddish brown cotton (cultivar BRS Safira) and the critical times for removing weeds. The experiment was carried out in the area of Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA) in Missao Velha-CE, Brazil, located at 7 degrees 42'07" S latitude and 39 degrees 24'18" WGr. longitude, during the 2007/2008 season. The treatments consisted of two control groups: weed-free crop during the initial period after crop emergency, and crop kept with weeds during initial period after plant emergency. Both consisted, 0; 20; 40; 60; 80 e 120 days after crop emergency (DAE), the weed community was evaluated by two phytosociological indices (relative dominance and relative importance). Regression analysis was performed as the model of sigmoidal Boltzman, using data from productivity separately within each type of competition, to identify the critical periods of competition, considering 2; 5 and 10% reduction in yield. The community of weeds was composed by 21 species, standing out among them: Richardia grandiflora, Amaranthus deflexus, Eleusine indica, Merremia aegyptia, Eragrotis pilosa, Cenchrus echinatus and Waltheria indica. Considering 2; 5 and 10% reduction in yield fiber as acceptable, the critical period before weed interference were, respectively, 8; 14 and 20 DAE. The critical period of weed interference, for those same levels of losses, were respectively, 100; 82 and 60 days.

Fontes de fibra na alimentação do pacu: desempenho, composição corporal e morfometria intestinal

O objetivo deste estudo foi avaliar os efeitos da utilização de diferentes ingredientes fibrosos nas dietas sobre o desempenho, a composição corporal e a morfometria intestinal de juvenis de pacu. Foram avaliadas cinco dietas isoproteicas (23% de proteína digestível), isoenergéticas (3250kcal de energia digestível/kg) e isofibrosas (9% de fibra bruta), sendo a principal fonte fibrosa de cada constituída por farelo de soja, casca de soja, farelo de girassol e polpa cítrica; esta última em dois níveis de inclusão (30 e 45%). Foram utilizados 300 juvenis de pacu (25,12±0,78 gramas), alojados em 25 aquários (200 litros). Os melhores resultados de crescimento e conversão alimentar foram obtidos com as dietas contendo farelo de soja e farelo de girassol. As dietas contendo casca de soja e polpa cítrica prejudicaram o desempenho dos juvenis de pacu, e o efeito negativo foi acentuado com o aumento da inclusão de polpa cítrica. Além disto, somente nos peixes alimentados com a dieta com 45% de polpa cítrica foi observada diminuição na densidade de vilosidades por área no epitélio intestinal. A partir dos resultados obtidos, pode-se concluir que alguns ingredientes fibrosos podem afetar negativamente o desempenho e as características do epitélio intestinal de juvenis de pacu.

Cultivo de híbridos de pimentão amarelo em fibra da casca de coco

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Consumo e dinâmica ruminal da fibra em detergente neutro em bovinos em pastejo no período das águas recebendo suplementação com nitrogênio não-proteico e/ou proteína verdadeira

Objetivou-se avaliar o efeito de diferentes relações entre proteína verdadeira e nitrogênio não-proteico sobre o consumo e a dinâmica de trânsito e degradação ruminal da fibra em detergente neutro (FDN) da forragem em bovinos em pastejo durante o período das águas. Foram utilizados cinco novilhos mestiços Holandês × Zebu, castrados, com peso corporal inicial de 335±35 kg fistulados no rúmen e no abomaso. Os tratamentos foram: controle (somente pasto); e suplementos com ureia; com 2/3 de compostos nitrogenados oriundos da ureia e 1/3 de compostos nitrogenados oriundos da albumina; com 1/3 de compostos nitrogenados oriundos da ureia e 2/3 de compostos nitrogenados oriundos da albumina; e com albumina. Foram fornecidos 200 g/dia de proteína bruta (PB) a partir dos suplementos. O experimento foi conduzido segundo delineamento em quadrado latino 5 × 5, com cinco períodos experimentais de 15 dias. Não foram observados efeitos da suplementação sobre o consumo voluntário, com exceção do consumo de PB, que aumentou com a suplementação. A substituição da ureia por albumina nos suplementos teve efeito linear sobre o consumo de PB. Os consumos dos demais componentes da dieta não foram afetados pela composição dos suplementos. Nenhum efeito foi observado sobre a taxa de passagem ruminal de compostos fibrosos. O fornecimento de suplementos ampliou, em média, a estimativa da taxa comum de latência e degradação da FDN. Contudo, não houve efeito da alteração na composição dos suplementos sobre este parâmetro. A suplementação de bovinos com fontes de compostos nitrogenados degradáveis no rúmen proteicos ou não-proteicos durante o período das águas não afeta o consumo voluntário de pasto.

Avaliação da determinação da fibra em detergente neutro e da fibra em detergente ácido pelo sistema ANKOM

O objetivo do trabalho foi comparar os valores de fibra em detergente neutro (FDN) e os de fibra em detergente ácido (FDA) obtidos com o equipamento ANKOM e pelo método convencional (Van Soest). No primeiro ensaio foram analisados cinco materiais diferentes (cana-de-açúcar, capim-braquiária, silagem de milho, polpa cítrica e fezes bovina) e testados quatro tipos de saquinhos para filtragem de amostra. O delineamento experimental foi em blocos casualizados, em um fatorial 5x4 (cinco materiais diferentes e quatro tipos de saquinhos de filtragem), com três repetições. As médias obtidas foram comparadas àquelas obtidas com método convencional. No segundo ensaio procurou-se avaliar o efeito da quantidade de amostra por saquinho (0,5; 0,8 e 1,0 g) sobre os teores de FDN e FDA em três tipos de alimentos, utilizando o ANKOM. Neste ensaio, o delineamento experimental foi em blocos casualizados em esquema fatorial 3x3 (três alimentos x três quantidades), com três repetições. Os tipos de saquinhos de filtragem utilizados não influenciaram os teores de FDN nos diferentes alimentos, com exceção das fezes, cujos saquinhos de náilon resultaram em concentrações de FDN inferiores. Não houve diferença entre os valores de FDN e FDA, obtidos pelo equipamento ANKOM ou pelo convencional, para os alimentos estudados, com exceção da polpa cítrica, cujo valor médio de FDA pelo ANKOM foi inferior àquele obtido pelo método convencional. A quantidade não exerceu efeito sobre a concentração de FDN dos alimentos analisados no equipamento ANKOM.

Efeitos de fontes nitrogenadas com distintas degradabilidades sobre o aproveitamento da fibra, do nitrogênio e do amido em rações para bovinos

O objetivo do experimento foi avaliar os efeitos da utilização do farelo de soja ou da glutenose sobre a degradabilidade ruminal in situ dos constituintes de dietas compostas por feno, milho e as fontes nitrogenadas fornecidas para bovinos adultos com 650 kg de peso. A glutenose foi considerada fonte nitrogenada de baixa degradabilidade e o farelo de soja, de média degradabilidade ruminal. As degradabilidades potenciais obtidas para o nitrogênio foram 39,7 e 90,3% e as degradabilidades efetivas 35,7 e 62,9%, respectivamente, para glutenose e farelo de soja. Utilizou-se a fibra mordente para determinar a taxa de passagem das dietas e obtiveram-se 6,6%/h para dietas com farelo de soja e 2,4%/h para dietas com glutenose. Não houve diferença na degradabilidade potencial da matéria seca do feno, nas frações A, B, C e na taxa de degradação, mas a degradabilidade efetiva da matéria seca foi inferior para as dietas com farelo de soja (29,3 vs 40,6%). Os demais ingredientes, à exceção do milho, apresentaram acentuadas diferenças entre as dietas nas variáveis de degradabilidade, na taxa de degradação e na degradabilidade efetiva do nitrogênio, com inferioridade na dieta com glutenose. O milho diferiu apenas quanto à degradabilidade efetiva do nitrogênio, superior na dieta com glutenose (68,7 vs 56,3%). O amido do milho apresentou menor degradabilidade efetiva na dieta com farelo de soja (52,5 vs 68,0%), sendo a degradabilidade efetiva da fibra do feno também inferior para essas dietas (27,3 vs 43,2%). Concluiu-se que fontes nitrogenadas com distintas degradabilidades podem afetar tanto a degradabilidade da fibra do volumoso quanto à do amido da própria fonte nitrogenada e do milho das dietas.

Degradabilidade da Matéria Seca e Fibra em Detergente Neutro da Cana-de-açúcar (Saccharum spp) com Diferentes Fontes de Proteína

Foram utilizados cinco bovinos fistulados no rúmen para se determinar a degradação da cana-de-açúcar em dietas com diferentes fontes de proteína degradável, por meio do método de incubação de sacos de náilon. Os tratamentos estudados foram: cana e uréia; cana e farelo de soja; cana, farelo de soja e uréia; cana e glúten de milho; cana, glúten de milho e uréia. Após um período de adaptação de 14 dias, iniciou-se a incubação dos sacos de náilon, nos tempos de 3, 6, 12, 24, 48, 72, 96 e 120 horas. Após o período de incubação, foram determinados o pH e a concentração de amônia no fluido ruminal, em amostras retiradas 0, 3, 6, 9, 12, 15, 18 e 21 horas após a alimentação. O delineamento estatístico utilizado foi o de blocos casualizados, com tratamentos como parcelas e tempos como subparcelas. A concentração de amônia foi mais elevada nos tratamentos com maior quantidade de proteína degradável, porém não houve efeito significativo para os tratamentos. Para os valores de pH, houve significância, apresentando valores mais elevados para os tratamentos com maior quantidade de proteína degradável. Não se observou efeito significativo das diferentes fontes de nitrogênio sobre a degradação da matéria seca e da fibra em detergente neutro da cana-de-açúcar, sendo que a degradabilidade dessas duas frações variou apenas com o tempo de incubação. Os resultados do experimento não comprovaram o princípio de que a maior quantidade de proteína degradável no rúmen possa induzir maior degradação da FDN da dieta.