Particulate composite based on coconut fiber and castor oil polyurethane adhesive: An eco-efficient product

This paper presents a study on the potential use of coconut fiber as material to produce particleboards, with two different densities (0.8 g/cm(3) and 1.0 g/cm3), using castor oil-based polyurethane adhesive and urea-formaldehyde. The quality of the product that can be produced by industry was evaluated according to the normative NBR 14.810:2006, where density, thickness swell (TS), absorption, modulus of elasticity (MOE), modulus of rupture (MOR) in static bending and internal bond (IB) were determined. From the results, there was a decrease in TS and increase in MOR of coconut fiber panels with polyurethane resin panels compared with coconut fiber and resin urea-formaldehyde. Scanning microscopy electronic images (SEM) indicated that castor oil-based polyurethane adhesive occupies the gaps between the particles, a factor that contributes to improved physical and mechanical properties of the panels. The assessment of durability through accelerated aging tests shows that panels protected with waterproofing material can be used in environments that have contact with moisture. (C) 2012 Elsevier B.V. All rights reserved.

Caratterizzazione meccanica di calcestruzzi fibrorinforzati con fibre d'acciaio

L’utilizzo di materiali compositi come i calcestruzzi fibrorinforzati sta diventando sempre più frequente e diffuso. Tuttavia la scelta di nuovi materiali richiede una approfondita analisi delle loro caratteristiche e dei loro comportamenti. I vantaggi forniti dall’aggiunta di fibre d’acciaio ad un materiale fragile, quale il calcestruzzo, sono legati al miglioramento della duttilità e all'aumento di assorbimento di energia. L’aggiunta di fibre permette quindi di migliorare il comportamento strutturale del composito, dando vita ad un nuovo materiale capace di lavorare non solo a compressione ma anche in piccola parte a trazione, ma soprattutto caratterizzato da una discreta duttilità ed una buona capacità plastica. Questa tesi ha avuto come fine l’analisi delle caratteristiche di questi compositi cementizi fibrorinforzati. Partendo da prove sperimentali classiche quali prove di trazione e compressione, si è arrivati alla caratterizzazione di questi materiali avvalendosi di una campagna sperimentale basata sull’applicazione della norma UNI 11039/2003. L’obiettivo principale di questo lavoro consiste nell’analizzare e nel confrontare calcestruzzi rinforzati con fibre di due diverse lunghezze e in diversi dosaggi. Studiando questi calcestruzzi si è cercato di comprendere meglio questi materiali e trovare un riscontro pratico ai comportamenti descritti in teorie ormai diffuse e consolidate. La comparazione dei risultati dei test condotti ha permesso di mettere in luce differenze tra i materiali rinforzati con l’aggiunta di fibre corte rispetto a quelli con fibre lunghe, ma ha anche permesso di mostrare e sottolineare le analogie che caratterizzano questi materiali fibrorinforzati. Sono stati affrontati inoltre gli aspetti legati alle fasi della costituzione di questi materiali sia da un punto di vista teorico sia da un punto di vista pratico. Infine è stato sviluppato un modello analitico basato sulla definizione di specifici diagrammi tensione-deformazione; i risultati di questo modello sono quindi stati confrontati con i dati sperimentali ottenuti in laboratorio.

Correlazioni tra proprietá reologiche, struttura e processabilitá di blend di LLDPE/LDPE

Polymer blends constitute a valuable way to produce relatively low cost new materials. A still open question concerns the miscibility of polyethylene blends. Deviations from the log-additivity rule of the newtonian viscosity are often taken as a signature of immiscibility of the two components. The aim of this thesis is to characterize the rheological behavior in shear and elongation of five series of LLDPE/LDPE blends whose parent polymers have been chosen with different viscosity and SCB content and length. Synergistic effects have been measured for both zero shear viscosity and melt strength. Both SCB length and viscosity ratio between the components have been found to be key parameters for the miscibility of the pure polymers. In particular the miscibility increases with increasing SCB length and with decreasing the LDPE molecular weight and viscosity. This rheological behavior has significant effects on the processability window of these blends when the uni or biaxial elongational flows are involved. The film blowing is one of the processes for which the synergistic effects above mentioned can be crucial. Small scale experiments of film blowing performed for one of the series of blends has demonstrated that the positive deviation of the melt strength enlarges the processability window. In particular, the bubble stability was found to improve or disappear when the melt strength of the samples increased. The blending of LDPE and LLDPE can even reduce undesired melt flow instability phenomena widening, as a consequence, the processability window in extrusion. One of the series of blends has been characterized by means of capillary rheometry in order to allow a careful morphological analysis of the surface of the extruded polymer jets by means of Scanning Electron Microscopy (SEM) with the aim to detect the very early stages of the small scale melt instabilty at low shear rates (sharksin) and to follow its subsequent evolution as long as the shear rate was increased. With this experimental procedure it was possible to evaluate the shear rate ranges corresponding to different flow regions: smooth extrudate surface (absence of instability), sharkskin (small scale instability produced at the capillary exit), stick-slip transition (instability involving the whole capillary wall) and gross melt fracture (i.e. a large scale "upstream" instability originating from the entrance region of the capillary). A quantitative map was finally worked out using which an assessment of the flow type for a given shear rate and blend composition can be predicted.

Struktur und rheologische Eigenschaften von PS-PI und PS-PB Blockcopolymeren

In der vorliegenden Arbeit wurde das Orientierungsverhalten der Mikrophasenseparation von industriellen und eigens synthetisierten Blockcopolymeren unter Extrusion untersucht.Dabei stellte sich heraus, daß bis auf eine Probe mit hexagonaler Morphologie die Mikrophasenseparationen der untersuchten Systeme unter dem Einfluß der Scherströmung derart in Extrusionsrichtung gedehnt werden, daß eine Art 'pseudo-lamellare' Morphologie entsteht. Aus Röntgenstreumessungen wurde die Güte dieser Orientierung in Form von Ordnungsparametern bestimmt. Dabei zeigte sich, daß der Orientierungsgrad der Proben deutlich von der Scherrate der Extrusion abhängt.Mit Hilfe von Zugversuchen konnte die mechanische Festigkeit der untersuchten Extrudate analysiert werden, wobei sich eine dem Ordnungsgrad analoge Scherratenabhängigkeit zeigte. Somit hat die rheologische Beanspruchung der Materialien einen deutlichen Einfluß auf deren mechanische Festigkeit.Im zweiten Teil der vorliegenden Arbeit wurde die Orientierung und die Reorientierung einer lamellaren Morphologie durch oszillatorische Verscherung mit großen Amplituden (LAOS) untersucht.Bei der Untersuchung des Orientierungsexperimentes zeigte sich, daß die exponentielle Abnahme der relativen Intensität des 3. Obertons (I3/I1) des fouriertransformierten Spektrums des Drehmomentes dazu genutzt werden konnte, um die Kinetik des Orientierungsprozesses zu bestimmen.Bei der Untersuchung des Umorientierungsprozesses konnte gezeigt werden, daß die nicht-lineare mechanische Antwort geeignet ist, um die Entwicklung bimodaler Orientierungsverteilungen zu verfolgen.

Latexpartikel als Trägermaterialien in der durch Postmetallocene katalysierten Ethenpolymerisation

Die vorliegende Arbeit beschäftigte sich mit der Immobilisierung von Postmetallocenen auf einem organischen Trägermaterial für die heterogene Ethenpolymerisation. Dabei konnte gezeigt werden, dass sich mit nukleophilen Gruppen funktionalisierte Latexpartikel als Trägermaterial für empfindliche Bis(phenoxyimin)titankatalysatoren eignen. Durch geschickte Kombination aus Trägermaterial, Katalysator und Cokatalysator wurde ein Katalysatorsysteme erhalten, das ultrahochmolekulares Polyethylen mit einem Molekulargewicht Mw von bis zu 7.000.000 g/mol (GPC, PS-Standard) bei einer enger Molekulargewichtsverteilung von weniger als 3 erzeugt. Die erhaltenen Produktivitäten erreichten dabei die Anforderungen an industriellen Katalysatorsystemen. Erstaunlich war, dass nukleophile Gruppen auf den Latexpartikeln, die dafür bekannt sind, dass sie den Katalysator deaktivieren können, ein wichtige Schutzfunktion für den Titankatalysator bilden. So konnte gezeigt werden, dass Pyridingruppen auf der Oberfläche der Latexpartikel als Scavenger gegen Trimethylaluminium wirken, welches ansonsten den aktiven Titankomplex zersetzen würde. An ausgewählten Systemen auf der Basis unterschiedlicher Postmetallocene und einem Metallocen für die Ethenpolymerisation wurde durch Anwendung verschiedener Methoden das Polymerisationsverhalten der Latex-geträgerten Katalysatorsysteme untersucht. Eine Methode war die so genannte Videomikroskopie, bei der in Gasphase Ethen polymerisiert wird und so das Wachstumsverhalten der Katalysatorpartikel analysiert werden kann. In Kombination mit einer kinetischen Kontrolle des Monomerumsatzes in Suspensionspolymerisation, konnte gezeigt werden, dass die auf Latexpartikel geträgerten Katalysatorsysteme ein anderes Polymerisationsverhalten besitzen wie in der Literatur beschriebene Silica-geträgerte Katalysatoren. Dies kann auf die unterschiedliche Beschaffenheit des Trägermaterials zurückgeführt werden. Während das harte Silica-Material Monomer nur in den Poren aufnimmt und so rasch nach Beginn der Polymerisation in eine diffusionskontrollierte Polymerisation übergeht, quillt das organische Trägermaterial mit dem Monomeren an und kann den aktiven Katalysator damit bedienen bis weiteres Monomer von außen in das Katalysatorpartikel nach diffundiert ist. Durch die weiche Beschaffenheit der organischen Latexpartikel kann das entstehende Polymer das Katalysatorpartikel außerdem leicht auseinandertreiben werden. Die Polymerisation kann so im ganzen Katalysatorpartikel beginnen, während das Silica-Trägermaterial nur langsam von außen nach innen fragmentieren kann.

Observations and modeling of the Marginal Ice Zone

Global climate change in recent decades has strongly influenced the Arctic generating pronounced warming accompanied by significant reduction of sea ice in seasonally ice-covered seas and a dramatic increase of open water regions exposed to wind [Stephenson et al., 2011]. By strongly scattering the wave energy, thick multiyear ice prevents swell from penetrating deeply into the Arctic pack ice. However, with the recent changes affecting Arctic sea ice, waves gain more energy from the extended fetch and can therefore penetrate further into the pack ice. Arctic sea ice also appears weaker during melt season, extending the transition zone between thick multi-year ice and the open ocean. This region is called the Marginal Ice Zone (MIZ). In the Arctic, the MIZ is mainly encountered in the marginal seas, such as the Nordic Seas, the Barents Sea, the Beaufort Sea and the Labrador Sea. Formed by numerous blocks of sea ice of various diameters (floes) the MIZ, under certain conditions, allows maritime transportation stimulating dreams of industrial and touristic exploitation of these regions and possibly allowing, in the next future, a maritime connection between the Atlantic and the Pacific. With the increasing human presence in the Arctic, waves pose security and safety issues. As marginal seas are targeted for oil and gas exploitation, understanding and predicting ocean waves and their effects on sea ice become crucial for structure design and for real time safety of operations. The juxtaposition of waves and sea ice represents a risk for personnel and equipment deployed on ice, and may complicate critical operations such as platform evacuations. The risk is difficult to evaluate because there are no long-term observations of waves in ice, swell events are difficult to predict from local conditions, ice breakup can occur on very short time-scales and wave-ice interactions are beyond the scope of current forecasting models [Liu and Mollo-Christensen, 1988,Marko, 2003]. In this thesis, a newly developed Waves in Ice Model (WIM) [Williams et al., 2013a,Williams et al., 2013b] and its related Ocean and Sea Ice model (OSIM) will be used to study the MIZ and the improvements of wave modeling in ice infested waters. The following work has been conducted in collaboration with the Nansen Environmental and Remote Sensing Center and within the SWARP project which aims to extend operational services supporting human activity in the Arctic by including forecast of waves in ice-covered seas, forecast of sea-ice in the presence of waves and remote sensing of both waves and sea ice conditions. The WIM will be included in the downstream forecasting services provided by Copernicus marine environment monitoring service.

Efficient fabrication of polymer nanocomposites with effective exfoliation and dispersion by solid-state/melt extrusion

In this communication, solid-state/melt extrusion (SSME) is introduced as a novel technique that combines solid-state shear pulverization (SSSP) and conventional twin screw extrusion (TSE) in a single extrusion system. The morphology and property enhancements in a model linear low-density polyethylene/organically modified clay nanocomposite sample fabricated via SSME were compared to those fabricated via SSSP and TSE. The results show that SSME is capable of exfoliating and dispersing the nanofillers similarly to SSSP, while achieving a desirable output rate and producing extrudate similar in form to that from TSE.

Proceedings of the Eighth Annual Biochemical Engineering Symposium

Contents"Effects of Swell-Shear Treatment on the Digestibility of Cellulosics", Dou-Houng Hwang, UMC "Application of Material and Energy Balance Regularities to Biomass Production from Cellulosic Substrates", Y.H. Lee, KSU "Immobilization of Aspergillus niger beta-Xylosidase", Gbekeloluwa B. Oguntimein, ISU "The Effect of the Major Structural Parameters of Cellulose on Enzymatic Hydrolysis", David H. Beardmore, Y.H. Lee, and L.T. Fan, KSU "Purification of a High Molecular Weight Hemicellulase", Ricardo A. Fournier, ISU "Aerobic Fermentation of Banana Pulp by Aspergillus Fumigatus", Stephen Lorbert, UMC "Purification and Properties of Two Very Small Xylanases", Chih-hen Kiang, ISU "Testing Theoretical Models for Cellulose Enzymatic Hydrolysis", Lin-Chang Chiang, UMC "Utilization of Material and Energy Balances in Hydrocarbon Fermentation", Alexis Ferrer, KSU "Purification of a Series of Closely Related Xylanases", Mary M. Frederick, ISU

Geotechnical engineering characterization of sediments at DSDP Leg 72 Holes

The hydraulic piston coring device (HPC-15) allows recovery of deep ocean sediments with minimal disturbance. The device was used during Leg 72 of the Deep Sea Drilling Project (DSDP) aboard the Glomar Challenger. Core samples were recovered from bore holes in the Rio Grande Rise in the southwest Atlantic Ocean. Relatively undisturbed sediment cores were obtained from Holes 515A, 516, 517, and 518. The results of shipboard physical property measurements and on-shore geotechnical laboratory tests on these cores are presented in this chapter. A limited number of 0.3 m cores were obtained and used in a series of geotechnical tests, including one-dimensional consolidation, direct shear, Atterburg limit, particle size analysis, and specific gravity tests. Throughout the testing program, attention was focused on assessment of sample disturbance associated with the HPC-15 coring device. The HPC-15 device limits sample disturbance reasonably well in terrigenous muds (clays). However, sample disturbance associated with coring calcareous sediments (nannofossil-foraminifer oozes) is severe. The noncohesive, granular behavior of the calcareous sediments is vulnerable to severe disturbance, because of the design of the sampling head on the device at the time of Leg 72. A number of modifications to the sampling head design are recommended and discussed in this chapter. The modifications will improve sample quality for testing purposes and provide longer unbroken core samples by reducing friction between the sediment column and the sampling tool.

Petrology and geochemistry of basalts from the Vavilov Basin

During ODP Leg 107, two holes were drilled in the basement of Vavilov Basin, a central oceanic area of the Tyrrhenian sea. Hole 655B is located near the Gortani ridge in off-axis position at the western rim of the basin; Hole 651A is located on a basement swell at the axis of the basin. This paper deals with mineral chemistry, major and trace element geochemistry, and petrogenesis of the basalts recovered in the two holes. The mineralogy of the basalts is broadly homogeneous, but all of them have suffered important seawater alteration. Their major-element compositions are similar to both normal-mid-ocean-ridge-basalts (N-MORB) and back-arc-basalts (BAB) except for Na2O contents (BAB-like), and K2O which is somewhat enriched in upper unit of Hole 651 A. Their affinity with N-MORB and BAB is confirmed by using immobile trace elements such as Zr, Y, and Nb. However, basalts from the two sites present contrasting geochemical characteristics on spidergrams using incompatible elements. Hole 655B basalts are homogeneous enriched tholeiites, similar to those from DSDP Hole 373 (located on the opposite side of the basin near the eastern rim), and show affinities with enriched MORB (E-MORB). At Hole 651 A, the two basalt units are chemically distinct. One sample recovered in lower unit is rather similar to those from Hole 655B, but basalts from upper unit display calc-alkaline characteristic evidenced by the increase of light-ion-lithophile-element (LILE)/high-field-strength-element (HFSE) ratio, and appearance of a negative Nb-anomaly, making them comparable with orogenic lavas from the adjacent Eolian arc. The observed chemical compositions of the basalts are consistent with a derivation of the magmas from a N-MORB type source progressively contaminated by LILE-enriched fluids released from dehydration of the bordering subducted plate. Implications for evolution of the Tyrrhenian basin are tentatively proposed taking into consideration geochemical and chronological relationships between basalts from Leg 107 Holes 655B and 651 A, together with data from Leg 42 Site 373 and Vavilov Seamount. These data illustrate back-arc spreading in ensialic basin closely associated with the maturation of the adjacent subduction, followed by the growth of late off-axis central volcano, whereas the active subduction retreats southeastward.