950 resultados para cellulosic pulp
Resumo:
In vitro studies have provided conflicting evidence of temperature changes in the tooth pulp chamber after low-level laser irradiation of the tooth surface. The present study was an in vitro evaluation of temperature increases in the human tooth pulp chamber after diode laser irradiation (GaAlAs, lambda = 808 nm) using different power densities. Twelve human teeth (three incisors, three canines, three premolars and three molars) were sectioned in the cervical third of the root and enlarged for the introduction of a thermocouple into the pulp chamber. The teeth were irradiated with 417 mW, 207 mW and 78 mW power outputs for 30 s on the vestibular surface approximately 2 mm from the cervical line of the crown. The highest average increase in temperature (5.6A degrees C) was observed in incisors irradiated with 417 mW. None of the teeth (incisors, canines, premolars or molars) irradiated with 207 mW showed temperature increases higher than 5.5A degrees C that could potentially be harmful to pulp tissue. Teeth irradiated with 78 mW showed lower temperature increases. The study showed that diode laser irradiation with a wavelength of 808 nm at 417 mW power output increased the pulp chamber temperature of certain groups of teeth, especially incisors and premolars, to critical threshold values for the dental pulp (5.5A degrees C). Thus, this study serves as a warning to clinicians that ""more"" is not necessarily ""better"".
Resumo:
Viral and bacterial associations appear to be implicated in the development of periodontal infections. Little information is available describing the periodontopathic agents in root canals with necrotic pulp. In this study, the occurrence and the combinations among herpes simplex virus type 1 (HSV-1) and Dialister pneumosintes, Tannerella forsythia.. and Treponema denticola in patients with chronic periodontitis and necrotic pulp were evaluated. Clinical samples from healthy subjects and patients with periodontal or pulp infections were analyzed using a nested polymerase chain reaction PCR to detect HSV and PCR to detect the 3 periodontal bacteria. The presence of Tannerella forsythia and Treponema denticola was observed in healthy, periodontitis, and necrotic pulp patients. HSV was observed in periodontitis and necrotic pulp patients, and no healthy subject harbored D. pneumosintes or HSV. The occurrence of Tannerella forsythia was not statistically significant in patients with necrotic pulp (P = 0.704). Periodontal bacteria were observed varying from 10.3% to 20.7% in periodontitis and necrotic pulp patients. The presence of Treponema denticola - HSV association was predominant in patients showing necrotic pulp (24.1%); however, HSV alone was observed in one patient with periodontitis and in another patient with necrotic pulp. The presence of double association among bacteria or bacteria - HSV could indicate a role in both periodontitis and necrotic pulp, and Tannerella forsythia - Treponenta denticola - HSV and Tannerella forsythia - D. pneumosintes - Treponema denticola - HSV associations might be important in periodontitis.
Resumo:
The structure and local ordering of 1,6-hexamethylenediisocyanate-(acetoxypropy1) cellulose (HDI-APC) liquid crystalline elastomer thin films are investigated by using X-ray diffraction and scattering techniques. Optical microscopy and mechanical essays are performed to complement the investigation. The study is performed in films subjected or not to an uniaxial stress. Our results indicate that the film is constituted by a bundle of helicoidal fiber-like structure, where the cellobiose block spins around the axis of the fiber, like a string-structure in a smectic-like packing, with the pitch defined by a smectic-like layer. The fibers are in average perpendicular to the smectic-like planes. Without the stretch, these bundles are warped, only with a residual orientation along the casting direction. The stretch orients the bundles along it, increasing the smectic-like and the nematic-like ordering of the fibers. Under stress, the network of molecules which connects the cellobiose blocs and forms the cellulosic matrix tends to organize their links in a hexagonal-like structure with lattice parameter commensurate to the smectic-like structure.
Resumo:
The aim of this study was to evaluate the hypothesis that low-level laser therapy (LLLT) 688 nm and 785 nm accelerate dentin barrier formation and repair process after traumatic pulp exposure. The sample consisted of 45 premolars of capuchin monkeys (Cebus apella) with pulp exposure Class V cavities. All premolars were treated with calcium hydroxide (Ca(OH)(2)), divided in groups of 15 teeth each, and analyzed on 7(th), 25(th), and 60(th) day. Group GI - only Ca(OH)(2), GIF- laser 688 nm, and GIII - laser 785 nm. Laser beam was used in single and punctual dose with the parameters: continuous, 688 nm and 785 nm wavelength, tip`s area of 0.00785 cm(2), power 50 mW, application time 20 s, dose 255 J/cm(2), energy 2 J. Teeth were capped with Ca(OH)(2), Ca(OH)(2) cement and restored with amalgam. All groups presented pulp repair. On 25(th) day the thickness of the formed dentin barrier was different between the groups GI and GII (p < 0.05) and between groups GI and GIII (p < 0.01). On 60(th) day there was difference between GI and GIII (p < 0.01). It may be concluded that, LLLT 688 nm and 785 nm accelerated dentin barrier formation and consequently pulp repair process, with best results using infrared laser 785 nm. (c) 2009 by Astro Ltd. Published exclusively by WLLEY-VCH Verlag GmbH & Co. KGaA
Resumo:
A method is reported for the quantification of isoorientin (using a standard addition method) and total flavonoids (expressed as rutin, using the external standard method) in passion fruit pulp (Passiflora edulis Sims f. flavicarpa Degener, Passifloraceae). Extraction of flavonoids was optimized by experimental design methodology, and quantitative analysis was performed by high-performance liquid chromatography with photo-diode array detection (HPLC-UV/DAD). The method was developed and validated according to ICH requirements for specificity, linearity, accuracy, precision (repeatability and intermediate precision). LOD and LOQ. Rutin was chosen as standard for the quantification of total flavonoids in order to propose a HPLC method feasible for routine analysis of the flavonoids in the passion fruit pulp. The passion fruit pulp contained 16.226 +/- 0.050 mg L(-1) of isoorientin and 158.037 +/- 0.602 mg L(-1) of total flavonoid, suggesting that P. edulis fruits may be comparable with other flavonoid food sources such as orange juice or sugarcane juice. (C) 2010 Elsevier B.V. All rights reserved.
Resumo:
Four different trials of stratified three-layered fine paper, of sulphate pulp, were performed to investigate if stratified fine fraction or fibres from birch can improve the properties of a paper compared to a reference sheet. All trials had five different scenarios and each scenario was calendered with different linear load. All sheets had a grammage of 80 g/m2.In the first trial, the paper contained birch, pine and filler of calciumcarbonate (marble), and was manufactured with the pilot paper machine XPM and the stratified headbox Formator at RCF (Stora Enso Research Center in Falun). The furnish consisted of 75% birch and 25% pine.The second trial contained coated sheets with paper from trial one as the base paper. The coating slip contained calciumcarbonate and clay and the amount was approximately 10-12 g/m2.The third trial, also with birch and pine but without filler, was performed at STFI (Skogsindustrins Tekniska Forskningsinstitut in Stockholm) with the laboratory scaled paper machine StratEx and the stratified headbox AQ-vanes. The furnish consisted of 75% birch and 25% pine, except for one scenario which contained of 75% pine and 25% birch.The last trial contained fractionated pulp of birch and pine and was performed at STFI. 50% was fine fraction and 50% was coarse fraction.This test does not show any clear benefits of making stratified sheets of birch and pine when it comes to properties such as bending stiffness, tensile index and surface smoothness. The retention can be improved with birch in the surface plies. It is possible that the formation can be improved with birch in the surface plies and pine in the middle ply. It is also possible that fine fraction in the surface plies and coarse fraction in the middle ply can improve both surface smoothness and bending stiffness. The results in this test are shown with confidence intervals which points out the difficulties of analysing sheets manufactured with a pilot paper machine or a laboratory scaled paper machine.
Resumo:
The volatiles (VOCs) and semi-volatile organic compounds (SVOCs) responsible for aroma are mainly present in skin of grape varieties. Thus, the present investigation is directed towards the optimisation of a solvent free methodology based on headspace-solid-phase microextraction (HS-SPME) combined with gas chromatography–quadrupole mass spectrometry (GC–qMS) in order to establish the global volatile composition in pulp and skin of Bual and Bastardo Vitis vinifera L. varieties. A deep study on the extraction-influencing parameters was performed, and the best results, expressed as GC peak area, number of identified compounds and reproducibility, were obtained using 4 g of sample homogenised in 5 mL of ultra-pure Milli-Q water in a 20 mL glass vial with addition of 2 g of sodium chloride (NaCl). A divinylbenzene/carboxen/polydimethylsiloxane fibre was selected for extraction at 60 °C for 45 min under continuous stirring at 800 rpm. More than 100 VOCs and SVOCs, including 27 monoterpenoids, 27 sesquiterpenoids, 21 carbonyl compounds, 17 alcohols (from which 2 aromatics), 10 C13 norisoprenoids and 5 acids were identified. The results showed that, for both grape varieties, the levels and number of volatiles in skin were considerably higher than those observed in pulp. According to the data obtained by principal component analysis (PCA), the establishment of the global volatile signature of grape and the relationship between different part of grapes—pulp and skin, may be an useful tool to winemaker decision to define the vinification procedures that improves the organoleptic characteristics of the corresponding wines and consequently contributed to an economic valorization and consumer acceptance.
Resumo:
Dietary modifications may significantly reduce cardiovascular disease (CVD) risk factors, including cholesterol and atherosclerosis. The present study addressed the effects of the crude extract from the pulp fruit of Tamarindus indica L. on lipid serum levels and early atherosclerotic lesions in hypercholesterolemic hamsters in vivo, and the extract's antioxidant action, in vitro. Animals were fed on either chow or atherogenic diet during 10 weeks and concomitantly received either water or T indica L. extract for drinking. Treatment of hypercholesterolemic hamsters with the T. indica pulp fruit extract (5%) led to a decrease in the levels of serum total cholesterol (50%), non-HDL cholesterol (73%) and triglyceride (60%), and to an increase of high-density lipoprotein (HDL) cholesterol levels (61%). In vitro, the extract presented radical scavenging ability, as assessed by the 2,2-diphenyl-1-picrylhydrazyl (DPPH) and superoxide radicals assays, and led to decreased lipid peroxidation in serum, as assessed by the thiobarbituric acid reactive substances (TBARS) assay. In vivo, the extract improved the efficiency of the antioxidant defense system, as assessed by the superoxide dismutase, catalase and glutathione peroxidase activities. Together these results indicate the potential of tamarind extracts in diminishing the risk of atherosclerosis development in humans. (c) 2005 Elsevier Ltd. All rights reserved.
Resumo:
Forragens com alta umidade e baixa concentração de carboidratos solúveis, como é o caso dos capins tropicais, podem conduzir a condições desfavoráveis para a produção de silagens de qualidade satisfatória. Esse estudo objetivou conhecer o perfil fermentativo e microbiológico de silagens de capim-Marandu [Brachiaria brizantha (Hochst ex. A. Rich) Stapf cv. Marandu], colhido com 58 dias de crescimento, aditivadas com polpa cítrica peletizada (PCP),. Foram utilizados silos experimentais de PVC adaptados com válvula do tipo Bunsen, tendo a silagem atingindo densidade de 900 kg m-3. Os tratamentos foram constituídos por três proporções de PCP (0, 50 e 100 g kg-1 em relação a matéria natural) e sete tempos de abertura após a ensilagem (1, 4, 7, 14, 21, 28 e 56 dias). A presença de PCP aumentou os teores de CHOs em 15 a 20%, reduziu o pH (5,3 para 4,2) e diminuiu as concentrações de N-NH3. Houve crescimento da população de enterobactérias somente durante o primeiro dia de fermentação (média 3 UFC g-1), pequeno desenvolvimento de clostrideos (média 0,5 UFC g-1) e dominância de bactérias homo em relação às heterofermentativas, para os três tratamentos estudados. A adição de polpa cítrica durante a ensilagem do capim-Marandu foi benéfica, podendo ser recomendada desde que haja benefício econômico na sua adoção.
Resumo:
No primeiro ensaio foram utilizados 16 suínos machos castrados da linhagem Topigs, com peso inicial de 80,5±4,7 kg, para a avaliação biológica da polpa cítrica. Por apresentar 18,85% de fibra em detergente neutro e 41,18% de fibra solúvel em detergente neutro, a polpa cítrica mostrou-se como um ingrediente viável a ser utilizado em programas de restrição alimentar qualitativa. No segundo ensaio foram utilizados 36 suínos machos castrados, com peso inicial de 83,7±5,1 kg, recebendo rações com níveis de 0, 10, 20 e 30% de polpa cítrica. Os animais foram abatidos com peso próximo de 130 kg, sendo avaliados quanto ao desempenho e parâmetros séricos. Houve resposta quadrática (P<0,05) para ganho diário de peso e número de dias para atingir o peso de 130 kg, em função dos níveis de polpa cítrica na dieta, sendo observados melhores resultados com níveis de inclusão de 10,79 e 10,97%, respectivamente. Para os parâmetros séricos avaliados, não foi observado efeito (P>0,05) dos níveis de polpa cítrica sobre a uréia e triacilgliceróis, porém houve resposta quadrática (P<0,05) para o colesterol em função dos níveis de polpa cítrica.
Resumo:
Foi realizado um ensaio utilizando 36 suínos machos castrados, com peso inicial de 83,7±5,1kg, para avaliar o efeito da inclusão de polpa cítrica, 0, 10, 20 e 30%, em um programa de restrição alimentar qualitativa para suínos abatidos aos 130kg de peso, sobre o peso dos órgãos do sistema digestório e sobre características da carcaça e da qualidade da carne. A inclusão de polpa cítrica proporcionou aumento linear (P<0,05) nos pesos do estômago, cólon e fígado, e efeito quadrático (P<0,05) no peso do ceco. Foi observada redução linear (P<0,05) no peso, no rendimento da carcaça e no peso do pernil, porém não houve efeito (P>0,05) sobre o rendimento do pernil. Maior inclusão de polpa cítrica não foi suficiente para reduzir a espessura do toucinho e aumentar a quantidade de carne magra na carcaça, mostrando que a restrição alimentar qualitativa não foi eficiente. Foi observado aumento linear (P<0,05) do pH da carcaça resfriada e linear negativo (P<0,05) sobre as variáveis indicativas de cor da carne em função da inclusão da polpa cítrica nas dietas. A adição de polpa cítrica em programas de restrição alimentar qualitativa não foi eficiente. Por não promover nenhum efeito deletério sobre as características da carne, a polpa cítrica pode ser utilizada como ingrediente alternativo para suínos em terminação.
Resumo:
Cellulose nanocrystals have been evaluated as reinforcement material in polymeric matrices due to their potential to improve the mechanical, optical, and dielectric properties of these matrixes. This work describes how high pressure defibrillation and chemical purification affect the sludge fiber morphology from micro to nanoscale. Microscopy techniques and X-ray diffraction were used to study the structure and properties of the prepared nanofibers and composites. Microscopic studies showed that the used individualization processes lead to a unique morphology of interconnected web-like structure of sludge fibers. The nanofibers are bundles of cellulose fibers having widths (5 to 30 nm) and estimated lengths of several micrometers.
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)