Utilização de óleos de origem vegetal em substituição aos derivados de petróleo em composições de borracha natural (NR)

A partir da publicação, em 1994, de um relatório que afirmava que a presença de óleos aromáticos pesados, com altos teores de compostos policíclicos, em formulações de borrachas estaria relacionada ao desenvolvimento de doenças como o câncer, associado ao fato da crescente conscientização ambiental na fabricação de produtos elastoméricos, foi iniciado um estudo sobre a substituição do óleo aromático de origem do petróleo por óleos vegetais de menor risco. Nessa Dissertação de Mestrado foi proposta a substituição do óleo aromático derivado do petróleo por óleos vegetais como o de tungue, palma e linhaça, em composições de borracha natural (NR) contendo diferentes teores do copolímero de butadieno-estireno (0, 10 e 50 phr) e diferentes tipos de carga (negro de fumo N330 e negro de fumo N375). As composições obtidas foram avaliadas quanto a propriedades reométricas, mecânicas e fractográficas. Foi observado que não houve variação significativa na viscosidade Mooney, na resistência à tração, no alongamento na ruptura e na dureza Shore das composições de NR SBR1502 quando o óleo aromático foi substituído pelos óleos vegetais, quando diferentes negros de fumo foram utilizados como carga reforçante e quando foram utilizados teores crescentes de SBR1502. Por outro lado, a resistência ao rasgamento das composições de NR SBR1502 apresentaram melhores resultados quando o negro de fumo N375 foi utilizado. A adição de teores crescentes de SR 1502 levou à diminuição dos valores de rasgo. A natureza do óleo utilizado influenciou esse resultado e melhores valores foram obtidos com o óleo de tungue. Os resultados obtidos foram corroborados pela morfologia do material, avaliadas por microscopia eletrônica de varredura

Novel dual transient temperature modulation technique for multi-vapour detection

Here we present a novel signal processing technique for a square wave thermally-modulated carbon black/polymer composite chemoresistor. The technique consists of only two mathematical operations: summing the off-transient and on-transient conductance signals; and subtracting the steady-state conductance signal. A single carbon black/polyvinylpyrrolidone composite chemo -resistor was fabricated and used to demonstrate the validity of the technique. Classification of water, methanol and ethanol vapours was successfully performed using only the peak time of the resultant curves. Quantification of the different vapours was also possible using the height of the peaks, because it was linearly proportional to concentration. This technique does not require zero-gas calibration and thus is superior to previously reported methods. ©2009 IEEE.

Impact response of polyethylene nanocomposites

The quasi-static and dynamic behaviour of Linear Low Density Polyethylene (LLDPE) and two LLDPE nanocomposites were studied. Nanocomposites consisting of LLDPE filled with 1% carbon black and 0.5% nanoclay fillers, by weight, were considered. Under quasi-static tensile loading, an improvement in the energy absorbing capability was achieved by adding 1% carbon black fillers. However, during quasi-static puncture and dynamic impact loading, the advantage provided by the fillers was lost. Thermal softening due to adiabatic heating under high strain rate deformation and difference s in the state of stress are considered as reasons for this reduction. © 2011 Published by Elsevier Ltd.

Vacuum pyrolysis of waste tires with basic additives

Granules of waste tires were pyrolyzed tinder vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na2CO3, NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 degrees C to 600 degrees C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 degrees C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 degrees C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) similar to 205 degrees C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt% which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na2CO3 addition. Pyrolysis gas was mainly composed of H-2, CO, CH4, CO2, C2H4 and C2H6. Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher.

Hydrogen Vanadate as an Effective Stabilizer of Pd Nanocatalysts for Formic Acid Electroxidation

In this paper, a simple chemical reduction route is discussed that results in small size, uniform dispersion of Pd nanoparticles supported on carbon black. HVO42-, the tridentate oxoanion with its O-O distance of 2.76 angstrom, closely matching with the Pd-Pd distance (2.75 angstrom), is expected to be an effective stabilizer for Pd according to the lattice size-matching binding model (Finke, R. G.; Ozkar, S. Coord. Chem. Rev. 2004, 248, 135). Because it has never been tested, HVO42- is exploited and found to be a very simple and effective stabilizer.

The preparation of high activity DMFC Pt/C electrocatalysts using a pre-precipitation method

It is suggested that a Pt/C cathodic catalyst for the direct methanol fuel cell (DMFC) can be prepared with a pre-precipitation method, in which, H2PtCl6 is precipitated onto the carbon black as (NH4)(2)PtCl6 before H2PtCl6 is reduced to Pt. The electrocatalytic activity of this Pt/C-A catalyst for oxygen reduction is excellent because the Pt/C catalyst prepared with this pre-precipitation method possesses a small average particle size, low relative crystalinity and a large electrochemically active surface area. In addition, the pre-precipitation method is simple and economical and it can be used to prepare a Pt/C catalyst on a large scale.

Morphological study on water-borne conducting polyaniline-poly(ethylene oxide) blends

Conducting polyaniline-poly(ethylene oxide) blends were prepared from their aqueous solutions. The blends displayed an electrical conductivity percolation threshold as low as 1.83 wt % of polyaniline loading. As demonstrated by scanning electron microscopy, polarized optical microscopy, and wide-angle X-ray diffraction studies, the conducting polyaniline took a fibrillar morphology in the blend, and it existed only in the amorphous phase of poly(ethylene oxide). A three-phase model combining morphological factors instead of a two-phase model was proposed to explain the low-conductivity percolation threshold.

Morphology of conductive blend fibers of polyaniline and polyamide-11

Polyaniline (PANI), a member of the intrinsically conducting polymer (ICPs) family, was blended with polyamide-11 (polyco-aminoundecanoyle) in concentrated sulfuric acid. The above solution was used to spin conductive PANI/polyamide-11 fibers by wet-spinning technology. Scanning electron microscope (SEM) and transmission electron microscope (TEM) were employed to study the two-phase morphology of the conductive PANI/polyamide-11 fibers. The micrographs of the cross-section, the axial section and the surface of the monofilament demonstrated that the two blend components were incompatible. The morphology of PANI in the fibers was of fibrillar form, which was valuable for producing conducting channels. The electrical conductivity of the fibers was from 10(-6) to 10(-1) S/cm with the different PANI fraction and the percolation threshold was about 5 wt.%. By comparing the two blend systems of PANI/Polyamide-11 fibers and carbon black filled poly(ethylene terephthalate) (PET) fibers, it was shown that the morphology of the conductive component had an influence on electrical conductivity, The former had higher conductivity and lower percolation threshold than the latter. (C) 2001 Elsevier Science B.V. All rights reserved.

Geossintéticos em vias de comunicação: influência das condições climáticas

Trabalho de Dissertação de Natureza Científica para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Vias de Comunicação e Transportes

Effets des nanoparticules manufacturées sur les cellules pulmonaires humaines

La détection et la caractérisation des nanoparticules manufacturées (NPM) est l’une des premières étapes pour contrôler et diminuer leurs risques potentiels sur la santé humaine et l’environnement. Différents systèmes d’échantillonnage dans l’air existent pour l’évaluation d’une exposition aux NPM. Cependant, ils ne mesurent pas le risque potentiel de cette exposition à la santé humaine ni les mécanismes cellulaires qui en seraient responsables. Nos objectifs de recherche sont 1) Évaluer les effets de différents types de nanoparticules sur des cellules pulmonaires humaines et 2) Identifier de nouveaux mécanismes intracellulaires activés lors de l’exposition à divers types de NPM. Méthodologie: La lignée de cellules A549 a été utilisée. Trois types de NPM ont été étudiés (différentes concentrations et temps d’exposition): les nanoparticules de dioxyde de titane de type anatase (TiO2), les nanotubes de carbone simple paroi (NTCSP) et les nanoparticules de noir de carbone (NC). La viabilité cellulaire a été mesurée par le test MTS, le test PrestoBlue et le test d’exclusion du bleu de Trypan (uniquement pour les NTCSP). La mesure du stress oxydatif a été déterminée par la mesure des dérivés réactifs de l’oxygène (ROS) en utilisant l’essai DCFH-DA. L’activation d’une réponse anti-oxydative a été déterminée par la mesure de la forme réduite (GSH) et oxydée (GSSG) du glutathion, ainsi que du ratio GSH/GSSG (seulement avec NTCSP et TiO2). Résultats: Les trois nanoparticules ne semblent pas être toxiques pour les cellules A549 car il y a une diminution significative mais minime de la viabilité cellulaire. Cependant, elles induisent une augmentation du contenu intracellulaire en ROS qui est à la fois dépendante du temps et de la concentration. Aucun changement dans les concentrations de GSH et GSSG n’a été observé. En conclusion, nos données indiquent que la mesure de la viabilité n’est pas un critère suffisant pour conclure à la toxicité des NPM. La production de ROS est un critère intéressant, cependant il faudra démontrer l’activation de systèmes anti-oxydatifs pour expliquer l’absence de mortalité cellulaire suite à l’exposition aux NPM.

Utilisation of IIR Tube Reclaim for Developing NR/IIR Blends

Butyl (IIR) tube reclaim (RR) was mixed with carbon black filled natural rubber (NR) compounds at various percentages. The blend containing a low percentage of RR was found to show improved ageing resistance and improved processability with out much reduction in the mechanical properties.