Propriedades estruturais e térmicas de vidros teluretos 20Li2O-80TeO2

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

New compositions of fluoroindate glasses with higher chemical resistance

In this paper, glasses in the systems In-Ba-Mg and In-Ba-Zn-Sr-Mg were water leachead at 80ºC showing surface degradation after 72 hours of leaching. The extent of such degradation is determined by the solubility and the concentration of the elemental fluorides that constitute the glasses. The formation of a layer of crystallized phases on the surface of the samples was observed. Small weight losses were registered and the absence of water on the glass matrix after the attack suggested that the use of MgF2 in the systems studied can lead to better results against moisture corrosion when compared to other fluoride glasses such as the fluorozirconates.

Optical spectroscopy and frequency upconversion properties of Tm3+ doped tungstate fluorophosphate glasses

Tungstate fluorophosphate glasses of good optical quality were synthesized by fusion of the components and casting under air atmosphere. The absorption spectra from near-infrared to visible were obtained and the Judd-Ofelt parameters determined from the absorption bands. Transition probabilities, excited state lifetimes and transition branching ratios, were, determined from the measurements. Pumping with a 354.7 nm beam from a pulsed laser. resulted in emission at 450 nm. due to transition D-1(2)-->F-3(4) in Tm3+ ions and a broadband emission centered at approximate to 550 nm attributed to the glass matrix. When pumping at 650 nm, two emission bands at 450 nm (D-1(2)-->F-3(4)) and at 790 nm (H-3(4)-->H-3(6)) were observed. Excitation spectra were also obtained in order to understand the origin of both emissions. Theoretical and experimental lifetimes were determined and,the results were explained in terms of multiphonon relaxation. (C) 2003 American Institute of Physics.

Raman spectroscopy analysis of structural photoinduced changes in GeS2 + Ga2O3 thin films

Photoexpansion and photobleaching effects have been observed in amorphous GeS2 + Ga2O3 (GGSO) thin films, when their surfaces were exposed to UV light. The photoinduced changes on the surface of the samples are indications that the structure has been changed as a result of photoexcitation. In this paper, micro-Raman, energy dispersive X-ray analysis (EDX) and backscattering electrons (BSE) microscopy were the techniques used to identify the origin of these effects. Raman spectra revealed that these phenomena are a consequence of the Ge-S bonds' breakdown and the formation of new Ge-O bonds, with an increase of the modes associated with Ge-O-Ge bonds and mixed oxysulphide tetrahedral units (S-Ge-O). The chemical composition measured by EDX and BSE microscopy images indicated that the irradiated area is oxygen rich. So, the present paper provides fundamental insights into the influence of the oxygen within the glass matrix on the considered photoinduced effects. (C) 2010 Elsevier B.V. All rights reserved.

Estudo da cinética de cristalização de vidros teluretos 20Li2O-80TeO2

Pós-graduação em Ciência dos Materiais - FEIS

Síntese e caracterização dos vidros teluretos do sistema (20-x)Li2O-80TeO2-xWO3

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Síntese e caracterização de vidros teluritos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Propriedades térmicas e estruturais de vidros teluretos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo das propriedades físicas em materiais vítreos do sistema 50B2O3 - 15CuO - 20Li2O - 15X (X= Na2O, K2O, RbCI e Cs2O)

The increasing demand for devices for solid state applications in many technological areas has resulted in a high demand for new materials. Among these material have the advantage of being manufactured with different chemical compositions, and may have physical properties equal to or higher than the corresponding crystalline material. The aim of this paper was to produce borate glass system 50B2O3 – 15CuO – 20Li2O – 15X (X = Na2O, K2O, RbCl e Cs2O) to analyze the influence of the atomic radius of alkali in the physical properties of this glass system. The glasses were synthesized by the process of melting and molding. The characteristic temperatures were determined by the technique of scanning calorimetry (DSC). The non-crystalline was determined by x-ray diffraction. In order to determine the molar volume a density measurement by using the Archimedes method was used. The structural characterization was carried out using the technique of infrared spectroscopy

An investigation into complex inorganic materials with Mössbauer spectroscopy

Mössbauer Spektroskopie ist ein unverzichtbares Instrument für die Bestimmung von Oxidationszuständen und für die Analyse von lokalen Ordnungsphänomenen von Mössbauer aktiven Atomen. Weil es sich um eine lokale Methode handelt können sowohl kristalline als auch amorphe Materialien untersucht werden. Die Kombination von lokaler Prüfung mit Mössbauer Spektroskopie und globaler Untersuchung z.B. mit Röntgendiffraktometrie ermöglicht die Studie von Ordnungseffekten von statistisch besetzten Positionen in einer geordneten Matrix. Das wurde hier eingesetzt um die lokale Umgebung in zwei Serien von Heuslerverbindungen, Co2-xFe1+xSi and Co2Mn1-xFexAl zu untersuchen. Für die Co2Mn1-xFexAl Serie wurde eine L21 geordnete Phase in einer insgesamt B2 geordneten Probe detektiert. Ein Wechsel von der AlCu2Mn zu der CuHg2Ti Struktur wurde für die Co2-xFe1+xSi Proben gefunden. Die Transformation von einem Glas zu einem keramischen Material wurde mit 119Sn Mössbauer Spektroskopie untersucht. Die höhere Ordnung in der Keramik wurde von einer kleiner werdenden Mössbauerlinienbreite begleitet. Demzufolge geben die Modifikationen der Sn Umgebungen klar die Transformation des gesamten Materials wieder. Ist die lokale Umgebung von unregelmäßig auftretenden Atomen in einer amorphen Matrix von Interesse, sind lokal prüfende Methoden die zuverlässigsten Methoden die zur Verfügung stehen. In dieser Arbeit wurde 119Sn Mössbauer Spektroskopie eingesetzt um die Oxidationszustände, die lokalen Umgebungen und relativen Intensitäten von Zinn Atomen in einer Silikatmatrix zu bestimmen. Modifikationen dieser Parameter als Funktion von Prozess bestimmenden Parametern wie der Sauerstoffpartialdruck, die Temperatur, die Behandlungsdauer und der Abkühlprozess genauso wie der SnO2 Gehalt sind von Interesse, weil durch Reduktions- und Diffusionsprozesse Änderungen des Koordinations- und des Oxidationszustands der Zinnatome auftreten. Da diese Änderungen in der Glasmatrix verursachen, die das fertige Produkt im industriellen Fertigungsprozess ruinieren können sind diese feinen Veränderungen sehr wichtig. Wenigstens zwei Mössbauerlinien korrespondierend mit zwei verschiedenen Umgebungen für Sn2+ und Sn4+ sind für eine Analyse mit ausreichender Qualität notwendig. Durch Vergleich von den bestimmten Hyperfein Parametern mit den Parametern von Modelsubstanzen werden lokale Umgebungen der Zinnatome entworfen. Für Sn2+ werden zwei auf einer trigonalen Pyramide basierende Umgebungen mit variierender Anzahl von bindenden und nicht-bindenden Sauerstoffatomen formuliert. Für Sn4+ wurde eine tetraedrische und eine oktaedrische Umgebung postuliert. Die relativen Intensitäten der vier Mössbauerlinien wurden um ein Diffusions- und Reaktionsmodell zu entwickeln und um einen Satz von Diffusions- und Transferkoeffizienten zu bestimmen eingesetzt. Die bestimmten Diffusionskoeffizienten stimmen mit den Literaturdaten überein. Der Massentransferkoeffizient ist kleiner als der bestimmte Wert, aber immer noch in der gleichen Größenordnung. Im Gegensatz zu den Erwartungen ist der präsentierte Diffusionskoeffizient für Sn4+ bestimmt als der von Sn2+. Das wiederum kann durch Berücksichtigung von Elektronhoppingprozessen erklärt werden.

Detection of enterotoxigenic Escherichia coli in foods by polymerase chain reaction

Enterotoxigenic Escherichia coli (ETEC) causes significant morbidity and mortality in infants of developing countries and is the most common cause of diarrhea in travelers to these areas. Enterotoxigenic Escherichia coli infections are commonly caused by ingestion of fecally contaminated food. A timely method for the detection of ETEC in foods would be important in the prevention of this disease. A multiplex polymerase chain reaction (PCR) assay which has been successful in detecting the heat-labile and heat-stable toxins of ETEC in stool was examined to determine its utility in foods. This PCR assay, preceded by a glass matrix and chaotropic DNA extraction, was effective in detecting high numbers of ETEC in a variety of foods. Ninety percent of 121 spiked food samples yielded positive results. Samples of salsa from Guadalajara, Mexico and Houston, Texas were collected and underwent DNA extraction and PCR. All samples yielded negative results for both the heat-labile and heat-stable toxins. Samples were also subjected to oligonucleotide probe analysis and resulted in 5 samples positive for ETEC. Upon dilution testing, it was found that positive PCR results only occurred when 12,000 to 1,000,000 bacteria were present in 200 mg of food. Although the DNA extraction and PCR method has been shown to be both sensitive and specific in stool, similar results were not obtained in food samples. ^

Tratamiento de superficie de las restauraciones de porcelana feldespática y su implicancia en la propagación de las fallas estructurales propias del material

Durante el proceso de elaboración de las porcelanas feldespáticas se producen en su interior micro rajaduras las cuales se propagan a través de la matriz vítrea aumentando la fragilidad del material cuando se lo expone a los esfuerzos mecánicos. Las restauraciones rígidas de porcelanas feldespáticas son sometidas a distintos tratamientos en su superficie para aumentar la adhesión a las estructuras dentarias cuando son cementadas. Estos tratamientos son acondicionamiento con ácido fluorhídrico y microarenado. Objetivos de este trabajo: 1. Evaluar la resistencia flexural de este material mediante ensayo mecánico en máquina Instron, previo tratamiento en su superficie con ácido fluorhídrico y microarenado. 2. Observar al MEB las alteraciones de superficie producidas por el microarenado y el ácido fluorhídrico. Los resultados obtenidos demostraron que el tratamiento de microarenado produjo una reducción de la resistencia flexural. El MEB confirmó la presencia de mayor cantidad de microgrietas que podrían ser responsables de la disminución de la resistencia flexural.

Chemistry of primary and secondary phases in intraplate basalts and volcaniclastic sediments at DSDP Leg 89 Holes

Electron microprobe data are presented for clinopyroxenes, plagioclases, palagonites, smectites, celadonites, and zeolites in Hole 462A sheet-flow basalts and Site 585 volcaniclastic sediments. Glomerocrystic clinopyroxenes in Hole 462A are predominantly Ti-poor augites with minor fractionation to ferroaugites in rim portions. Quenched plumose clinopyroxenes show considerable variation from Ca-rich to Ca-poor augites, although all are characterized by being Tirich and Cr-poor relative to the glomerocrysts. Two differentiated series of Site 585 pyroxene compositions, calcic augite and diopside-salite, demonstrate the coexistence, in the vitric and lithic clasts, of tholeiitic and alkali basalt types, respectively. Plagioclase compositions in all samples are mainly labradorites, although some zoned Hole 462A glomerocrysts range from An73 to An20 and are characterized by high Mg and Fe contents in the more calcic varieties. The K content of the plagioclases is highest in the more sodic crystals, although the overall higher orthoclase component of Site 585 plagioclases reflects the generally higher bulk-rock K content. The compositions of both secondary smectites and celadonites are similar irrespective of the alteration location (glass, matrix, vesicles, etc.), although brown smectites replacing interstitial glass have marginally higher total Fe contents than pale green and yellow smectites. Analyzed zeolites are mainly phillipsites with variable alkali content, and, together with associated celadonite, represent late-stage alteration repositories for K under mildly oxidizing conditions. The compositions of both early and late secondary minerals are typical of those formed by the submarine alteration of basaltic rocks at low temperatures.

Synthesis and characterization of Tellurium oxide glasses for photonic applications

Tellurite glasses are photonic materials of special interest to the branch of optoelectronic and communication, due to its important optical properties such as high refractive index, broad IR transmittance, low phonon energy etc. Tellurite glasses are solutions to the search of potential candidates for nonlinear optical devices. Low phonon energy makes it an efficient host for dopant ions like rare earths, allowing a better environment for radiative transitions. The dopant ions maintain majority of their individual properties in the glass matrix. Tellurites are less toxic than chalcogenides, more chemically and thermally stable which makes them a highly suitable fiber material for nonlinear applications in the midinfrared and they are of increased research interest in applications like laser, amplifier, sensor etc. Low melting point and glass transition temperature helps tellurite glass preparation easier than other glass families.In order to probe into the versatility of tellurite glasses in optoelectronic industry; we have synthesized and undertaken various optical studies on tellurite glasses. We have proved that the highly nonlinear tellurite glasses are suitable candidates in optical limiting, with comparatively lower optical limiting threshold. Tuning the optical properties of glasses is an important factor in the optoelectronic research. We have found that thermal poling is an efficient mechanism in tuning the optical properties of these materials. Another important nonlinear phenomenon found in zinc tellurite glasses is their ability to switch from reverse saturable absorption to saturable absorption in the presence of lanthanide ions. The proposed thesis to be submitted will have seven chapters.

Dielectric anomaly in strontium borate-bismuth vanadate glass nanocomposite

Transparent glass nanocomposites in the pseudo binary system (100 - x) SrB4O7 (SBO)-x Bi2VO5.5 (BiV) (0 less than or equal to n less than or equal to 70) were prepared by the splat quenching technique. The nano-crystallization of bismuth vanadate (BiV) in 50 SBO-50 BiV (in mol%) glass composite has been demonstrated. These were characterized for their structural, thermal and dielectric properties. As-quenched composites under study have been confirmed to be amorphous by X-ray powder diffraction (XRD) studies. The glass transition temperature (T-g) and crystallization temperatures (T-er) were determined using differential thermal analyses (DTA), High resolution transmission electron microscopic (HRTEM) studies carried out on heat-treated samples reveal the presence of spherical nanosize crystallites of Bi2VO5.5 (BiV) dispersed in the glassy matrix of SrB4O7 (SSO). The dielectric constant (epsilon (r)) and the dielectric loss (D) measurements were carried out on the as-quenched and heat-treated glass nanocomposite samples in the frequency range 100 Hz-10 MHz. The as-quenched and the heat-treated at two different temperatures (720 and 820 K) samples exhibited broad dielectric anomalies in the vicinity of the ferroelectric-to-paraelectric transition temperature of the parent BiV ceramics. The Curie-Weiss law was found to be valid at a temperature above the transition temperature, establishing the diffused nature of the transition. (C) 2001 Elsevier Science Ltd. All rights reserved.