Variation in the sensitivity of DOC release between different organic soils following H2SO4 and sea-salt additions

Long-term monitoring data from eastern North America and Europe indicate a link between increased dissolved organic carbon (DOC) concentrations in surface waters over the last two decades and decreased atmospheric pollutant and marine sulphur (S) deposition. The hypothesis is that decreased acidity and ionic strength associated with declining S deposition has increased the solubility of DOC. However, the sign and magnitude of DOC trends have varied between sites, and in some cases at sites where S deposition has declined, no significant increase in DOC has been observed, creating uncertainty about the causal mechanisms driving the observed trends. In this paper, we demonstrate chemical regulation of DOC release from organic soils in batch experiments caused by changes in acidity and conductivity (measured as a proxy for ionic strength) associated with controlled SO42− additions. DOC release from the top 10 cm of the O-horizon of organo-mineral soils and peats decreased by 21–60% in response to additions of 0–437 µeq SO42− l−1 sulphuric acid (H2SO4) and neutral sea-salt solutions (containing Na+, Mg2+, Cl−, SO42−) over a 20-hour extraction period. A significant decrease in the proportion of the acid-sensitive coloured aromatic humic acids (measured by specific ultra-violet absorbance (SUVA) at 254 nm) was also found with increasing acidity (P < 0.05) in most, but not all, soils, confirming that DOC quality, as well as quantity, changed with SO42− additions. DOC release appeared to be more sensitive to increased acidity than to increased conductivity. By comparing the change in DOC release with bulk soil properties, we found that DOC release from the O-horizon of organo-mineral soils and semi-confined peats, which contained greater exchangeable aluminium (Al) and had lower base saturation (BS), were more sensitive to SO42− additions than DOC release from blanket peats with low concentrations of exchangeable Al and greater BS. Therefore, variation in soil type and acid/base status between sites may partly explain the difference in the magnitude of DOC changes seen at different sites where declines in S deposition have been similar.

Selected wheat seed defense proteins exhibit competitive binding to model microbial lipid interfaces

Puroindolines (Pins) and purothionins (Pths) are basic, amphiphilic, cysteine-rich wheat proteins that play a role in plant defense against microbial pathogens. We have examined the co-adsorption and sequential addition of Pins (Pin-a, Pin-b and a mutant form of Pin-b with Trp-44 to Arg-44 substitution) and β-purothionin (β-Pth) model anionic lipid layers, using a combination of surface pressure measurements, external reflection FTIR spectroscopy and neutron reflectometry. Results highlighted differences in the protein binding mechanisms, and in the competitive binding and penetration of lipid layers between respective Pins and β-Pth. Pin-a formed a blanket-like layer of protein below the lipid surface that resulted in the reduction or inhibition of β-Pth penetration of the lipid layer. Wild-type Pin-b participated in co-operative binding with β-Pth, whereas the mutant Pin-b did not bind to the lipid layer in the presence of β-Pth. The results provide further insight into the role of hydrophobic and cationic amino acid residues in antimicrobial activity.

Scanning tunneling microscopy and molecular dynamics study of the Li2TiO3(001) surface

We have investigated the (001) surface structure of lithium titanate (Li2TiO3) using auger electron spectroscopy (AES), low-energy electron diffraction (LEED), and scanning tunneling microscopy (STM). Li2TiO3 is a potential fusion reactor blanket material. After annealing at 1200 K, LEED demonstrated that the Li2TiO3(001) surface was well ordered and not reconstructed. STM imaging showed that terraces are separated in height by about 0.3 nm suggesting a single termination layer. Moreover, hexagonal patterns with a periodicity of ∼0.4 nm are observed. On the basis of molecular dynamics (MD) simulations, these are interpreted as a dynamic arrangement of Li atoms.

Money laundering and the shadow economy in Kazakhstan

Purpose The purpose of this paper is to assess and highlight the approach taken towards the legal control of illicit money laundering taken in the Republic of Kazakhstan, in particular, the role played by an amnesty on the legalisation of illicit funds. This is particularly important as a basis for a wider discussion about the proper limits of the “criminalising” approaches commonly taken in anti-money laundering regulations. Design/methodology/approach The discussion and evaluation in the paper is based upon a conceptual analysis of the money laundering regime in Kazakhstan, in particular, the legal framework and policies of implementation adopted. Findings The paper demonstrates that the problems that are posed by the shadow economy in post-Soviet transition societies can make the blanket criminalisation of money laundering a self-defeating approach, unless accompanied by measures which allow for the achievement of “market-constituting” effects. Research limitations/implications The paper draws on experience and practice in one jurisdiction only (Kazakhstan); it also limits its focus to one particular example of a money laundering amnesty policy. Both of these limitations, therefore, suggest avenues for further comparative research. Originality/value The paper’s conclusions about the interactions between the shadow economies of transitional societies and the global anti-money laundering agenda have wider application in assessments of international law in this area.

Vegetation history, human impact and climate change during prehistory: an island perspective of the isles of Tiree, Coll and north-west Mull

Results of extensive site reconnaissance on the Isles of Tiree, Coll and north-west Mull, Inner Hebrides are presented. Pollen-stratigraphic records were compiled from a profile from Glen Aros, north-west Mull and from two profiles on Coll located at Loch an t-Sagairt and Caolas an Eilean. Quantification of microscopic charcoal provided records that were used to facilitate a preliminary evaluation of the causal driving mechanisms of vegetation change. Bayesian modelling of radiocarbon dates was used to construct preliminary chronological frameworks for these records. Basal sedimentary deposits at Glen Aros contain pollen records that correspond with vegetation succession typical of the early Holocene dating to c. 11,370 cal BP. Woodland development is a key feature of the pollen records dating to the early Holocene, while records from Loch an t-Sagairt show that blanket mire communities were widespread in north-west Coll by c. 9800 cal BP. The Corylus-rise is dated to c. 10,710 cal BP at Glen Aros and c. 9905 cal BP at Loch an t-Sagairt, with records indicating extensive cover of hazel woodland with birch. All of the major arboreal taxa were recorded, though Quercus and Ulmus were nowhere widespread. Analysis of wood charcoal remains from a Mesolithic site at Fiskary Bay, Coll indicate that Salix and Populus are likely to be under-represented in the pollen records. Reconstructed isopoll maps appear to underplay the importance of alder in western Scotland during the mid-Holocene. Alder-rise expansions in microscopic charcoal dating to c. 7300 cal BP at Glen Aros and c. 6510 to 5830 cal BP on Coll provide records of significance to the issue of human-induced burning related to the expansion of alder in Britain. Increasing frequencies in microscopic charcoal are correlated with mid-Holocene records of increasing aridity in western Scotland after c. 7490 cal BP at Glen Aros, 6760 cal BP at Loch an t-Sagairt and 6590 cal BP at Caolas an Eilean, while several phases of increasing bog surface wetness were detected in the Loch an t-Sagairt archive during the Holocene. At least five phases of small-scale woodland disturbance during the Mesolithic period were identified in the Glen Aros profile dating to c. 11,650 cal BP, 9300 cal BP, 7840 cal BP, 7040 cal BP and 6100 cal BP. The timing of the third phase is coincident with evidence of Mesolithic settlement at Creit Dhu, north-west Mull. Three phases of small-scale woodland disturbance were detected at Loch an t-Sagairt dating to c. 9270 cal BP, 8770 cal BP and 8270 cal BP, all of which overlap chronologically with evidence of Mesolithic activity at Fiskary Bay, Coll. A number of these episodes are aligned chronologically with phases of Holocene climate variability such as the 8.2 K event.

The Léger ruling as another example of the ECJ’s disappointingly reticent approach to the protection of the rights of LGB persons under EU law

In the 1980s, in the midst of the AIDS epidemic, many countries introduced lifetime bans on blood donations by men who had sexual relations with men (MSM). These blanket bans have, recently, begun to be challenged and, as a result, many countries have either relaxed them or completely abolished them. The case under examination (Léger ) is another instance of questioning the legality of such a ban. In particular, in this case, the European Court of Justice was called on to rule on whether a measure such as the French lifetime exclusion from blood donation of the MSM population that was at issue before the referring court is contrary to EU law. The Court ruled that although discriminatory on the ground of sexual orientation, such a ban may be justified in certain circumstances, and left it to the national court to make the final decision. This article seeks to analyse the case and to explain why, in the author’s view, the Court can be accused of—once more—not going far enough in the protection of lesbian, gay and bisexual (LGB) rights.

Effect of enzymatic pretreatment and increasing the organic loading rate of lipid-rich wastewater treated in a hybrid UASB reactor

This study aimed at evaluating the effect of increasing organic loading rates and of enzyme pretreatment on the stability and efficiency of a hybrid upflow anaerobic sludge blanket reactor (UASBh) treating dairy effluent. The UASBh was submitted to the following average organic loading rates (OLR) 0.98 Kg.m(-3).d(-1), 4.58 Kg.m(-3).d(-1), 8.89 Kg.m(-3).d(-1) and 15.73 Kg.m(-3).d(-1), and with the higher value, the reactor was fed with effluent with and without an enzymatic pretreatment to hydrolyze fats. The hydraulic detention time was 24 h, and the temperature was 30 +/- 2 degrees C. The reactor was equipped with a superior foam bed and showed good efficiency and stability until an OLR of 8.89 Kg.m(-3).d(-1). The foam bed was efficient for solid retention and residual volatile acid concentration consumption. The enzymatic pretreatment did not contribute to the process stability, propitiating loss in both biomass and system efficiency. Specific methanogenic activity tests indicated the presence of inhibition after the sludge had been submitted to the pretreated effluent It was concluded that continuous exposure to the hydrolysis products or to the enzyme caused a dramatic drop in the efficiency and stability of the process, and the single exposure of the biomass to this condition did not inhibit methane formation. (C) 2011 Elsevier B.V. All rights reserved.

A comparison of two bench-scale anaerobic systems used for the treatment of dairy effluents

The objective of this work was to compare two anaerobic reactor conflgurations, a hybrid upflow anaerobic sludge blanket (UASBh) reactor and an anaerobic sequencing batch reactor with immobilised biomass (ASBBR) treating dairy effluents. The reactors were fed with effluent from the milk pasteurisation process (effluent 1-E1) and later with effluent from the same process combined with the one from the cheese manufacturing (effluent 2-E2). The ASBBR reactor showed average organic matter removal efficiency of 95.2% for E1 and 93.5% for E2, while the hybrid UASB reactor showed removal efficiencies of 90.3% and 80.1% respectively.

Bayesian network classifiers: Beyond classification accuracy

This work proposes and discusses an approach for inducing Bayesian classifiers aimed at balancing the tradeoff between the precise probability estimates produced by time consuming unrestricted Bayesian networks and the computational efficiency of Naive Bayes (NB) classifiers. The proposed approach is based on the fundamental principles of the Heuristic Search Bayesian network learning. The Markov Blanket concept, as well as a proposed ""approximate Markov Blanket"" are used to reduce the number of nodes that form the Bayesian network to be induced from data. Consequently, the usually high computational cost of the heuristic search learning algorithms can be lessened, while Bayesian network structures better than NB can be achieved. The resulting algorithms, called DMBC (Dynamic Markov Blanket Classifier) and A-DMBC (Approximate DMBC), are empirically assessed in twelve domains that illustrate scenarios of particular interest. The obtained results are compared with NB and Tree Augmented Network (TAN) classifiers, and confinn that both proposed algorithms can provide good classification accuracies and better probability estimates than NB and TAN, while being more computationally efficient than the widely used K2 Algorithm.

Utredning om huruvida Dalarnas Tidningars produktion passar en KBA Cortina

This degree project illustrates newsprint and waterless offset. A new news press was introduced at Drupa-00, Cortina from KBA, which is the first news press dedicated the waterless technique. With actual statistics from the company in question an investigation was made whether their production fits this press. It came out in the investigation that the production of the company, from statistics, fits this press very good. A table was made where different timeschedules were accounted for the new press, with semi- and full automatic plate changing for present and to be added papers. The waterless technology is compared to conventional offset with the difference that the plate is based on a sort of laminatetechnology. Like conventional plates this plate has a base made of aluminium. Lightsensitive photopolymer isunited as a layer or coat on top of the aluminium and a 2µm thin oleophobic siliconlayer is applied on top of the photopolymer. Considering the print, the waterless method has a higher qualitygrade than conventional offset. No water is emulsifiedin the ink, and therefore the printed dot gets a higher density. The loss of dampening solution and higher tack of the ink gives sharper dots. This makes the colourspace bigger why a greater range of colours can be printed. The loss of dampening solution gives a more stable dotgain, which contributes to that a higher screen can be used. The disadvantage is that the plate can't do as many rotations as the conventional plate. A waterless plate makes around 100 000-500 000 rotations before it needs to be removed owing to type- and manufacturer of the plate. The plate is also slightly more sensitive and expensive than conventional plates, around 1,4 - 1,7 × aluminium printing plates. A waterless system can be installed in a conventional printing press by degrees and when large editions are being printed a cooler needs to be installed in the oscillationrollers of the press, since an increase in temperature can make the oleophobic parts of the plate oleophilic. The Cortina is however equipped with a temperature controlsystem at the beginning. To avoid picking, caused by the tacky ink, a blanket with a high “quick release” should be used.

Troubleshooting med avseende på avsättningar på gummiduk, Bobergs tryckeri AB

Bobergs printing house in Falun has during some time had problems regarding deposits on blankets intheirs Müller Martini UV-printing presses. Deposits appear in both image areas and non-image areas.These areas have been analyzed and the deposits on non-image areas contain chalk, clay and talc. Thequestion remains how these material bond to the blanket surface. The chalk and clay comes from thepaper. The talc comes from the ink. Deposits from image areas contain pigment and talc from the printingink. The dampening water has also been analyzed. The result shows some sort of problem with thehardness regulator for the clean water. The pH-level should be increased a few steps.

American Indian Blankets

Raid the Icebox 1 with Andy Warhol exhibition installation negative of a blanket chest containing American Indian blankets. The top lid and front drawer are open.

Uso de reator seqüencial em batelada (RSB) para pós-tratamento de efluente de reator anaeróbio

Este trabalho consistiu no pós-tratamento de efluente de reator anaeróbio, em um sistema de reator seqüencial em batelada (RSB), com vistas à remoção biológica de nitrogênio e fósforo. Primeiramente, em escala de laboratório, verificou-se a eficiência de três RSBs, com ciclos operacionais diferenciados, tratando o efluente produzido por um reator seqüencial em batelada anaeróbio (RSBAn), alimentado por esgoto sintético, caracteristicamente doméstico. Neste experimento, também acoplou-se um sistema de aquisição de dados aos RSBs, para monitorar continuamente os parâmetros pH, redox e OD, com o objetivo de obter pontos inferenciais de controle dos processos de nitrificação, desnitrificação e remoção biológica de fósforo. Subseqüente a este experimento, desenvolveu-se um sistema de RSB em escala piloto, tratando o efluente anaeróbio real de um UASB (Upflow Anaerobic Sludge Blanket), no intuito de analisar o efeito da mudança de escala e do tipo de esgoto, que passou de sintético a real, na performance do RSB. No experimento em escala de laboratório, os resultados obtidos demonstraram boas eficiências de remoção de DQO e SS, e uma ótima eficiência no processo de nitrificação. As eficiências médias de remoção de DQO, SS e nitrificação, foram respectivamente de 93,3%, 90,7% e 98,9%. O processo de desnitrificação não desenvolveu-se satisfatoriamente devido às baixas concentrações de matéria orgânica do efluente anaeróbio. O processo de remoção biológica de fósforo, além das baixas DQO afluentes, foi prejudicado pelas idades de lodo extremamente longas estabelecidas nesta fase experimental, em função da aplicação da estratégia de controle de processo baseada na concentração de SSV no licor. Objetivando-se aumentar a concentração de matéria orgânica imediatamente disponível no afluente, com o conseqüente acréscimo de eficiência nos processos de desnitrificação e remoção biológica de fósforo, introduziu-se um pré-fermentador, para gerar metade do efluente anaeróbio a ser tratado nos RSBs. O controle do processo passou a ser efetuado através da aplicação de uma idade de lodo pré-estabelecida de 20 dias. Observou-se um aumento bastante significativo do processo de desnitrificação, atingindo uma eficiência da ordem de 70,4%. No entanto, as maiores concentrações de matéria orgânica solúvel, com a introdução do pré-fermentador, não foram suficientes para estimular o desenvolvimento das bactérias removedoras de fósforo. Um aumento de DQO do esgoto sintético foi necessário para permitir a simultaneidade dos processos de desnitrificação e remoção de fósforo. Porém, apesar de apresentar ciclos operacionais com eficiências de 100% de remoção de fósforo, este processo não mostrou-se confiável, alternando entre fases de boas, médias e más eficiências. Provavelmente as idades de lodo, ainda muito altas para promover a remoção de fósforo do sistema, justificam a permanência bastante irregular na eficiência deste processo. Neste período, a concentração média de DQO necessária para atingir-se uma eficiência satisfatória nos processos conjuntos de nitrificação e desnitrificação, foi de 644,6 mg/L. As seguintes eficiências foram observadas: 95,8% na remoção de DQO, 98,7% na nitrificação, 76,8% na desnitrificação e 74,5% na remoção de nitrogênio. O acompanhamento "on line" de pH, redox e OD mostrou-se como uma eficiente ferramenta inferencial no controle de processos biológicos, principalmente daqueles referentes à remoção de nitrogênio. Dentre os três parâmetros monitorados, o pH apresentouse como o mais representativo. No experimento em escala piloto, o processo de nitrificação não desenvolveu-se possivelmente devido ao efeito conjunto de baixos tempos de detenção nas etapas aeróbias dos ciclos operacionais dos RSBs, com a ação tóxica de sulfetos produzidos no tratamento anaeróbio. O processo de remoção biológica de fósforo, similarmente ao experimento em escala de bancada, não mostrou-se confiável, apresentando períodos alternados de eficiência. Por fim, com vistas a verificar o desenvolvimento de processo inibitório por efluentes de tratamento anaeróbio em sistemas aeróbios, realizou-se uma série de testes de inibição com o efluente anaeróbio e também especificamente com sulfeto. Os testes respirométricos (DBO última e em batelada), foram de essencial importância para analisar a tratabilidade biológica de esgoto contendo composto tóxico. Pôde-se comprovar que o sulfeto, presente no efluente anaeróbio real, ou o efeito de sua combinação com outras substâncias contidas no lodo ativado, alterou a cinética dos processos biológicos desenvolvidos no sistema de tratamento do tipo lodo ativado.

Avaliação de concretos reforçados por confinamento com manta de fibra de vidro estrutural e pré-impreganada

Due to the occurrence of diseases in the use of structural reinforcements in composites, with presentation of concrete blanket detachment, has been identified the need to evaluate the performance of concrete reinforced with glass fiber. This study aims to evaluate these concretes by means of testing methodologies, using concrete with low resistance with structural reinforcement for confinement by preimpregnated glass fiber and traditional fiberglass blanket. The first stage of work was the development of methodologies for analysis, opting for four types, such as the acoustic survey, strength to compressive, the pull-off and ultrasound. Next, tests were carried out using the four selected methodologies in 30 of proof-of-specimens by 5x10 cm, 15 were reinforced with the traditional fiberglass blanket with 5specimens exposed to test a marine environment of marine coastline of Natal-RN and 15 were reinforced with a pre-impregnated glass fiber blanket, as well as 5specimens exposed to a test environment of the marine coastline of Natal-RN. After conducting the acoustic survey, it has been verified a lack of delaminating and air bubbles in the samples, confirming the absence of gross shortcomings in the implementation of the ribs both the traditional fiberglass blanket and in the preimpregnated fiber glass blanket. After carrying out methods of pull-off and compressive strengthening test it was observed that the reinforced proof-bodies with pre-impregnated glass blanket showed maximum stresses higher than the traditional fiberglass blanket; consequently a greater grip with the formation of a smaller area of . fracture, unlike traditional glass mat, which showed lower maximum stresses, with a greater area of fracture. It was also found that the traditional fiberglass blanket presented detachment of blanket-concrete interface, unlike the pre-impregnated fiberglass blanket, which showed a better grip on the blanket-concrete interface. In the trial of ultrasound there was no presence of cracks in the blanket-concrete interface, yielding to both blankets good compactness of the concrete. At the end of this work, they were developed and proposed two methods of testing for evaluation of reinforced concrete structures with composites, for standardization, the acoustic survey and pull-off

Estudo sobre as potencialidades de compósitos à base de gesso e fibras de coco seco para aplicação na construção civil

The use of gypsum, one of the oldest building materials for the construction industry in the country has been experiencing a significant and steady growth, due to its low cost and some of its properties that confer comparative advantage over other binder materials. Its use comprises various applications including the coating of walls and the production of internal seals and linings. Moreover, the fibers are being increasingly incorporated into arrays fragile in an attempt to improve the properties of the composite by reducing the number of cracks, the opening of the same and its propagation velocity. Other properties, depending on the function of the component material or construction, among these thermal and acoustic performances, are of great importance in the context of buildings and could be improved, that is, having better performance with this embodiment. Conduct a comparative study of physico-mechanical, thermal and acoustic composite gypsum incorporating dry coconut fiber, in the form of blanket, constituted the main objective of this work. Improving the thermal and acoustic performances of precast gypsum, used for lining and internal vertical fences of buildings, was the purpose of development of these composites. To evaluate the effect of fiber content on the properties of the composites were used to manufacture the composite layer with different thicknesses. The composites were fabricated in the form of plates with dimensions of 500x500x24mm. To facilitate the comparative study of the properties were also made with material gypsum boards only. We then determined the physico-mechanical, thermal and acoustical plaster and composites. The results indicated that the composites were significant gains in relation to thermal performance and also acoustic, in certain frequency range, increasing the thickness of the blanket. Concerning other physical-mechanical properties, the results showed that although the compressive strength was lower than for the composite did not occur after a fracture catastrophic failure. The same trend was observed with regard to resistance to bending, since the composites have not suffered sudden rupture and still continued after the load supporting point of maximum load