Study of seawater biofiltration by measuring adenosine triphosphate (ATP) and turbidity

In the present study, we examined seawater biofiltration in terms of adenosine triphosphate (ATP) and turbidity. A pilot biofilter continuously fed with fresh seawater reduced both turbidity and biological activity measured by ATP. Experiments operated with an empty bed contact time (EBCT) of between 2 and 14 min resulted in cellular ATP removals of 32% to 60% and turbidity removals of 38% to 75%. Analysis of the water from backwashing the biofilter revealed that the first half of the biofilter concentrated around 80% of the active biomass and colloidal material that produces turbidity. By reducing the EBCT, the biological activity moved from the first part of the biofilter to the end. Balances of cellular ATP and turbidity between consecutive backwashings indicated that the biological activity generated in the biofilter represented more than 90% of the detached cellular ATP. In contrast, the trapped ATP was less than 10% of the overall cellular ATP detached during the backwashing process. Furthermore, the biological activity generated in the biofilter seemed to be more dependent on the elapsed time than the volume filtered. In contrast, the turbidity trapped in the biofilter was proportional to the volume filtered, although a slightly higher amount of turbidity was found in the backwashing water; this was probably due to attrition of the bed medium. Finally, no correlations were found between turbidity and ATP, indicating that the two parameters focus on different matter. This suggests that turbidity should not be used as an alternative to cellular concentration.

Characterization Method for Comminution Behavior of Limestone and Fuel Ash in a Circulating Fluidized Bed Boiler

Työn tavoite oli kehittää karakterisointimenetelmät kalkkikiven ja polttoaineen tuhkan jauhautumisen ennustamiselle kiertoleijukattilan tulipesässä. Kiintoainekäyttäytymisen karakterisoinnilla ja mallintamisella voidaan tarkentaa tulipesän lämmönsiirron ja tuhkajaon ennustamista. Osittain kokeelliset karakterisointimenetelmät perustuvat kalkkikiven jauhautumiseen laboratoriokokoluokan leijutetussa kvartsiputkireaktorissa ja tuhkan jauhatumiseen rotaatiomyllyssä. Karakterisointimenetelmät ottavat huomioon eri-laiset toimintaolosuhteet kaupallisen kokoluokan kiertoleijukattiloissa. Menetelmät kelpoistettiin kaupallisen kokoluokan kiertoleijukattiloista mitattujen ja fraktioittaisella kiintoainemallilla mallinnettujen taseiden avulla. Kelpoistamistaseiden vähäisyydestä huolimatta karakterisointimenetelmät arvioitiin virhetarkastelujen perusteella järkeviksi. Karakterisointimenetelmien kehittämistä ja tarkentamista tullaan jatkamaan.

Human disease and drug pharmacology, complex as real life

In the past decades drug discovery practice has escaped from the complexity of the formerly used phenotypic screening in animals to focus on assessing drug effects on isolated protein targets in the search for drugs that exclusively and potently hit one selected target, thought to be critical for a given disease, while not affecting at all any other target to avoid the occurrence of side-effects. However, reality does not conform to these expectations, and, conversely, this approach has been concurrent with increased attrition figures in late-stage clinical trials, precisely due to lack of efficacy and safety. In this context, a network biology perspective of human disease and treatment has burst into the drug discovery scenario to bring it back to the consideration of the complexity of living organisms and particularly of the (patho)physiological environment where protein targets are (mal)functioning and where drugs have to exert their restoring action. Under this perspective, it has been found that usually there is not one but several disease-causing genes and, therefore, not one but several relevant protein targets to be hit, which do not work on isolation but in a highly interconnected manner, and that most known drugs are inherently promiscuous. In this light, the rationale behind the currently prevailing single-target-based drug discovery approach might even seem a Utopia, while, conversely, the notion that the complexity of human disease must be tackled with complex polypharmacological therapeutic interventions constitutes a difficult-torefuse argument that is spurring the development of multitarget therapies.

Modelling of combustion and sorbent reactions in three-dimensional flow environment of a circulating fluidized bed furnace

This thesis presents a three-dimensional, semi-empirical, steady state model for simulating the combustion, gasification, and formation of emissions in circulating fluidized bed (CFB) processes. In a large-scale CFB furnace, the local feeding of fuel, air, and other input materials, as well as the limited mixing rate of different reactants produce inhomogeneous process conditions. To simulate the real conditions, the furnace should be modelled three-dimensionally or the three-dimensional effects should be taken into account. The only available methods for simulating the large CFB furnaces three-dimensionally are semi-empirical models, which apply a relatively coarse calculation mesh and a combination of fundamental conservation equations, theoretical models and empirical correlations. The number of such models is extremely small. The main objective of this work was to achieve a model which can be applied to calculating industrial scale CFB boilers and which can simulate all the essential sub-phenomena: fluid dynamics, reactions, the attrition of particles, and heat transfer. The core of the work was to develop the model frame and the required sub-models for determining the combustion and sorbent reactions. The objective was reached, and the developed model was successfully used for studying various industrial scale CFB boilers combusting different types of fuel. The model for sorbent reactions, which includes the main reactions for calcitic limestones, was applied for studying the new possible phenomena occurring in the oxygen-fired combustion. The presented combustion and sorbent models and principles can be utilized in other model approaches as well, including other empirical and semi-empirical model approaches, and CFD based simulations. The main achievement is the overall model frame which can be utilized for the further development and testing of new sub-models and theories, and for concentrating the knowledge gathered from the experimental work carried out at bench scale, pilot scale and industrial scale apparatus, and from the computational work performed by other modelling methods.

Influence of Cutting Conditions on Tool Life, Tool Wear and Surface Finish in the Face Milling Process

The main goal of this work is to study the influence of cutting conditions - cutting speed, feed velocity and feed per tooth - on tool life and surface finish of the workpiece in the face milling of flat surfaces. Aiming to achieve this goal, several milling experiments were carried out with different cutting speeds, feed velocities and feeds per tooth. In the first phase of the experiments, cutting speed was varied without varying feed velocity, which caused a variation in feed per tooth. In the second phase of the experiments, cutting speed and feed velocity were varied in such a way that feed per tooth was kept constant. Tool flank wear and surface roughness of the workpiece were measured as cutting time elapsed. The main conclusions of this work are that a) cutting speed has a strong influence on tool life, regardless of whether feed velocity or feed per tooth varies and b) an increase in surface roughness of the workpiece is not closely related to an increase in wear of the primary cutting edge.

Container logistic innovations in forest-energy sector: Markets, future service concepts and technical improvements

The report presents the results of the commercialization project called the Container logistic services for forest bioenergy. The project promotes new business that is emerging around overall container logistic services in the bioenergy sector. The results assess the European markets of the container logistics for biomass, enablers for new business creation and required service bundles for the concept. We also demonstrate the customer value of the container logistic services for different market segments. The concept analysis is based on concept mapping, quality function deployment process (QFD) and business network analysis. The business network analysis assesses key shareholders and their mutual connections. The performance of the roadside chipping chain is analysed by the logistic cost simulation, RFID system demonstration and freezing tests. The EU has set the renewable energy target to 20 % in 2020 of which Biomass could account for two-thirds. In the Europe, the production of wood fuels was 132.9 million solid-m3 in 2012 and production of wood chips and particles was 69.0 million solidm3. The wood-based chips and particle flows are suitable for container transportation providing market of 180.6 million loose- m3 which mean 4.5 million container loads per year. The intermodal logistics of trucks and trains are promising for the composite containers because the biomass does not freeze onto the inner surfaces in the unloading situations. The overall service concept includes several packages: container rental, container maintenance, terminal services, RFID-tracking service, and simulation and ERP-integration service. The container rental and maintenance would provide transportation entrepreneurs a way to increase the capacity without high investment costs. The RFID-concept would lead to better work planning improving profitability throughout the logistic chain and simulation supports fuel supply optimization.

Female administrators and the mentors who give them full support /

A looming attrition rate, a steady increase in the number of women in administration, and a lack of Canadian research all provided the rationale for this study. The problem in this study was to investigate the needs and challenges of new female administrators and to examine the role that mentors play in addressing these issues. This study also explored the perceived benefits of having a mentor. This study examined the inductive year of 33 female administrators from 3 Ontario school boards. It was a qualitative and quantitative design, using questionnaire and interview data. It was found that the majority felt that they struggled with biases and expectations that were gender specific. The challenges that were perceived to be most prevalent were categorized into 4 thematic areas: Maintaining Balance, Feeling Pressured, The Perceptions of Others, and Being Challenged by Others. Regarding the benefits of mentoring, the participants perceived mentoring to be most beneficial in terms of professional growth, followed by learning how to run a school, and then career advancement. The significance of this study was threefold: it had theoretical implications as well as implications for practice and future research. Suggestions included: facilitating longitudinal relationships, having the board become more actively involved in facilitating the relationship, and implementing an internship program. This study attempted to extend the current literature by theorizing that a mentorship is cyclical in nature. Future research could include program design and implementation, as well as providing consistent and accessible mentoring opportunities for all.

Abrasion, transport and distribution of sediment in selected streams of Southern Ontario and Western New York /

The rate of decrease in mean sediment size and weight per square metre along a 54 km reach of the Credit River was found to depend on variations in the channel geometry. The distribution of a specific sediment size consist of: (1) a transport zone; (2) an accumulation zone; and (3) a depletion zone. These zones shift downstream in response to downcurrent decreases in stream competence. Along a .285 km man-made pond, within the Credit River study area, the sediment is also characterized by downstream shifting accumulation zones for each finer clast size. The discharge required to initiate movement of 8 cm and 6 cm blocks in Cazenovia Creek is closely approximated by Baker and Ritter's equation. Incipient motion of blocks in Twenty Mile Creek is best predicted by Yalin's relation which is more efficient in deeper flows. The transport distance of blocks in both streams depends on channel roughness and geometry. Natural abrasion and distribution of clasts may depend on the size of the surrounding sediment and variations in flow competence. The cumulative percent weight loss with distance of laboratory abraded dolostone is defined by a power function. The decrease in weight of dolostone follows a negative exponential. In the abrasion mill, chipping causes the high initial weight loss of dolostone; crushing and grinding produce most of the subsequent weight loss. Clast size was found to have little effect on the abrasion of dolostone within the diameter range considered. Increasing the speed of the mill increased the initial amount of weight loss but decreased the rate of abrasion. The abrasion mill was found to produce more weight loss than stream action. The maximum percent weight loss determined from laboratory and field abrasion data is approximately 40 percent of the weight loss observed along the Credit River. Selective sorting of sediment explains the remaining percentage, not accounted for by abrasion.

Exploring the potential of early identification and intervention within a college of applied arts

This study probed for an answer to the question, "How do you identify as early as possible those students who are at risk of failing or dropping out of college so that intervention can take place?" by field testing two diagnostic instruments with a group of first semester Seneca College Computer Studies students. In some respects, the research approach was such as might be taken in a pilot study. Because of the complexity of the issue, this study did not attempt to go beyond discovery, understanding and description. Although some inferences may be drawn from the results of the study, no attempt was made to establish any causal relationship between or among the factors or variables represented here. Both quantitative and qualitative data were gathered during. four resea~ch phases: background, early identification, intervention, and evaluation. To gain a better understanding of the problem of student attrition within the School of Computer Studies at Seneca College, several methods were used, including retrospective analysis of enrollment statistics, faculty and student interviews and questionnaires, and tracking of the sample population. The significance of the problem was confirmed by the results of this study. The findings further confirmed the importance of the role of faculty in student retention and support the need to improve the quality of teacher/student interaction. As well, the need __f or ~~ills as~e:ss_~ent foll,,-~ed }JY supportiv e_c_ounsell~_I'l9_ ~~d_ __ placement was supported by the findings from this study. strategies for reducing student attrition were identified by faculty and students. As part of this study, a project referred to as "A Student Alert project" (ASAP) was undertaken at the School of Computer Studies at Seneca College. Two commercial diagnostic instruments, the Noel/Levitz College Student Inventory (CSI) and the Learning and Study Strategies Inventory (LASSI), provided quantitative data which were subsequently analyzed in Phase 4 in order to assess their usefulness as early identification tools. The findings show some support for using these instruments in a two-stage approach to early identification and intervention: the CSI as an early identification instrument and the LASSI as a counselling tool for those students who have been identified as being at risk. The findings from the preliminary attempts at intervention confirmed the need for a structured student advisement program where faculty are selected, trained, and recognized for their advisor role. Based on the finding that very few students acted on the diagnostic results and recommendations, the need for institutional intervention by way of intrusive measures was confirmed.

Exploring the potential of early identification and intervention within a college of applied arts

This study probed for an answer to the question, "How do you identify as early as possible those students who are at risk of failing or dropping out of college so that intervention can take place?" by field testing two diagnostic instruments with a group of first semester Seneca College Computer ,Studies students. In some respects, the research approach was such as might be taken in a pilot study_ Because of the complexity of the issue, this study did not attempt to go beyond discovery, understanding and description. Although some inferences may be drawn from the results of the study, no attempt was made to establish any causal relationship between or among the factors or variables represented here. Both quantitative and qualitative data were gathered during four resea~ch phases: background, early identification, intervention, and evaluation. To gain a better understanding of the problem of student attrition within the School of Computer Studies at Seneca College, several methods were used, including retrospective analysis of enrollment statistics, faculty and student interviews and questionnaires, and tracking of the sample population. The significance of the problem was confirmed by the results of this study. The findings further confirmed the importance of the role of faculty in student retention and support the need to improve the quality of teacher/student interaction. As well, the need for skills assessmen~-followed by supportive counselling, and placement was supported by the findings from this study. strategies for reducing student attrition were identified by faculty and students. As part of this study, a project referred to as "A Student Alert Project" (ASAP) was undertaken at the School of Computer Studies at Seneca college. Two commercial diagnostic instruments, the Noel/Levitz College Student Inventory (CSI) and the Learning and Study Strategies Inventory (LASSI), provided quantitative data which were subsequently analyzed in Phase 4 in order to assess their usefulness as early identification tools. The findings show some support for using these instruments in a two-stage approach to early identification and intervention: the CSI as an early identification instrument and the LASSI as a counselling tool for those students who have been identified as being at risk. The findings from the preliminary attempts at intervention confirmed the need for a structured student advisement program where faculty are selected, trained, and recognized for their advisor role. Based on the finding that very few students acted on the diagnostic results and recommendations, the need for institutional intervention by way of intrusive measures was confirmed.

An Analysis of Minor Hockey Officials and Perceived Organizational Support

Recent research suggests organizational factors should be considered in order to better understand the attrition of minor hockey. Consequently, the purpose of this quantitative study was to examine the extent to which minor hockey officials perceive organizational support (POS) from the minor hockey system, and to compare POS among minor hockey officials according to demographics. A total of 261 minor hockey officials were surveyed with the Survey of Perceived Organizational Support (SPOS). Results indicated significant differences according minor hockey official experience, certification level and extra-role performance. The findings are discussed in relation to POS and human resource management literature, and recommendations are made as to how administrators can better support these officials.

L'attrition de la marque d'usage PROVERBIAL de la 7e (1878) à la 8e (1932-35) édition du Dictionnaire de l'Académie française

Notre mémoire porte sur l’attrition de la marque d’usage PROVERBIAL de la 7e (1878) à la 8e édition du Dictionnaire de l’Académie française (1932-35). L’informatisation des huit éditions achevées de l’ouvrage (Redon 2002), qui permet tant le relevé quantitatif que qualitatif des données, laisse voir que la marque jouit d’une grande stabilité dans les sept premières éditions, mais que son emploi chute considérablement de l’édition de 1878 à celle de 1932-35. Dans les limites notre projet, nous tâchons de comprendre le comment de cette érosion. Pour ce faire, nous avons recensé exhaustivement les lexies touchées de la 7e à la 8e édition, en tenant compte des cas de figure logiquement possibles : retrait d’un article ou d’une lexie dans la 8e édition, lexies partagées avec la 7e édition mais a) dépouillées de la marque, b) marquées différemment ou c) héritières du marquage d’origine. Dans l’édition de 1878, PROVERBIAL s’applique à 4 674 lexies distribuées dans 1 645 articles. Au terme de notre recherche, nous identifions les expressions proverbiales disparues ou maintenues dans le passage crucial de la 7e à la 8e édition du Dictionnaire de l’Académie française. Nous en tirons des résultats qui portent, entre autres, sur la transformation du système de marquage dans la tradition du Dictionnaire de l’institution.

Prédiction de l'attrition en date de renouvellement en assurance automobile avec processus gaussiens

Le domaine de l’assurance automobile fonctionne par cycles présentant des phases de profitabilité et d’autres de non-profitabilité. Dans les phases de non-profitabilité, les compagnies d’assurance ont généralement le réflexe d’augmenter le coût des primes afin de tenter de réduire les pertes. Par contre, de très grandes augmentations peuvent avoir pour effet de massivement faire fuir la clientèle vers les compétiteurs. Un trop haut taux d’attrition pourrait avoir un effet négatif sur la profitabilité à long terme de la compagnie. Une bonne gestion des augmentations de taux se révèle donc primordiale pour une compagnie d’assurance. Ce mémoire a pour but de construire un outil de simulation de l’allure du porte- feuille d’assurance détenu par un assureur en fonction du changement de taux proposé à chacun des assurés. Une procédure utilisant des régressions à l’aide de processus gaus- siens univariés est développée. Cette procédure offre une performance supérieure à la régression logistique, le modèle généralement utilisé pour effectuer ce genre de tâche.

Analyse de l'attrition des enseignants au Québec

L’abandon de la carrière chez les enseignants, généralement appelé l’attrition des enseignants dans les écrits scientifiques, a été l’objet de nombreuses études. La connaissance en est assez avancée dans certaines régions du monde, mais très peu de recherches ont étudié cette problématique au Québec. Ainsi, l’objectif principal de ce travail de recherche était d’identifier les facteurs de l’attrition des enseignants au Québec. L’objectif spécifique de cette recherche était d’observer comment ces facteurs influencent la perception des individus et amènent certains d’entre eux à prendre la décision de quitter. Dans le cadre de cette étude qualitative, 26 individus (16 femmes et 10 hommes) ayant récemment quitté l’enseignement ont été rencontrés. Dix participants ont exercé la profession enseignante au niveau primaire et 16 au niveau secondaire. Afin de recueillir les données, le chercheur a procédé à des entrevues de groupe semi-dirigées d’une durée de deux heures. Les résultats de cette étude indiquent que les facteurs qui influencent l’attrition des enseignants au Québec sont nombreux et variés. Ils sont surtout relatifs aux conditions d’exercice de la profession et les plus souvent mentionnés sont les difficultés liées à la gestion de classe, la précarité du travail, les difficultés dans les relations avec les collègues, la charge de travail et le peu de soutien offert par la direction. Le contexte social et la faible valorisation de la profession enseignante ont aussi été mentionnés. Par ailleurs, le chercheur a analysé la perception qu’avaient les participants de leur expérience de travail à l’aide de la théorie de l’autodétermination (Deci et Ryan, 2000). Les résultats de cette analyse suggèrent que les participants ne se sentaient pas en mesure de satisfaire leurs besoins psychologiques fondamentaux dans le cadre du travail enseignant.

Granular Attrition due to Rotary Valve in a Pneumatic Conveying System

The rotary valve is a widely used mechanical device in many solids-handling industrial processes. However, it may also be responsible for most of the attrition effects occurring in a typical process. In this study, the attrition effects occurring in a rotary valve operating as a stand-alone device and as part of a pneumatic conveying system were investigated. In the former case granular attrition was carried out at three different rotary valve speeds and the experimental results obtained were found to be in good agreement with the Gwyn correlation. In the latter case three typical air flow rates were used in the pneumatic conveying system. The size distribution of the attrition product obtained at the lowest air flow rate used was not adequately described by the Gwyn correlation. The attrition process and mechanisms involved were analysed and the minimum size of the attrition product obtained from both modes of operations was found to be similar.