Dehairing Australian alpaca fibres with a cashmere dehairing machine

Many classes of alpaca fibres contain a certain amount of coarse fibres, which are strong and stiff, and cause discomfort to the end users of the alpaca fibre products. It is therefore desirable to separate the coarse fibres from the fine alpaca fibres. This paper reports trial results on alpaca dehairing using a cashmere dehairing machine. The diameters of alpaca fleece, dehaired alpaca fibres and removed alpaca fibres were analysed, and the fibre lengths before and after dehairing have been compared. The results indicate that it is feasible to dehair alpaca fibres using a cashmere dehairing facility. The dehaired alpaca fibres are cleaner, bulkier and softer, with around 1.5 μm reduction in average fibre diameter, but the dehairing process shortens the dehaired fibre length considerably. The dehairing effectiveness of coarse fibre removal using the cashmere dehairing technology has also been discussed in this paper.

Design and simulation of an interdigital-chaotic advection micromixer for lab-on-a-chip applications

This paper presents the design and simulation of a novel passive micromixer. The micromixer consists of two inlet tanks, one mixing channel and two outlet channels. In order to maximise the mixing efficiency, the following considerations are made: (i) The inlet tanks are followed by a series of microchannels, in which the flow is split. The microchannels are arranged in an interdigital manner to maximise the contact area between the two flows. (ii) The microchannels attached to the lower inlet tank have an upward slope while those attached to the upper tank have a downward slope. The higher-density flow is fed to the lower inlet tank and gets an upward velocity before entering the mixing channel. (iii) Two triangular barriers are placed within the mixing channel to impose chaotic advection and perturb the less-mixed flow along the top and bottom surfaces of the channel. (iv) Finally, two outlet channels are incorporated to discard the less-mixed flow. Three-dimensional simulations are carried out to evaluate the performance of the micromixer. Simulations are performed in the absence and presence of the gravitational force to analyse the influence of gravity on the micromixer. Mixing efficiencies of greater than 92% are achieved using water and a 1011'density biological solvent as the mixing fluids.

An artificial neural network-based hairiness prediction model for worsted wool yarns

This study evaluated the performance of multilayer perceptron (MLP) and multivariate linear regression (MLR) models for predicting the hairiness of worsted-spun wool yarns from various top, yarn and processing parameters. The results indicated that the MLP model predicted yarn hairiness more accurately than the MLR model, and should have wide mill specific applications. On the basis of sensitivity analysis, the factors that affected yarn hairiness significantly included yarn twist, ring size, average fiber length (hauteur), fiber diameter and yarn count, with twist having the greatest impact on yarn hairiness.

Design and simulation of an interdigital-chaotic advection micromixer for lab-on-a-chip applications

The paper presents the design and simulation of a novel passive micromixer. The micromixer consists of two inlet tanks, one mixing channel and two outlet channels. In order to maximise the mixing efficiency, the following considerations are made : (i) The inlet tanks are followed by a series of microchannels, in which the flow is split. The microchannels are arranged in an interdigital manner to  maximise the contact area between the two flows. (ii) The microchannels attached to the lower inlet tank have an upward slope while those attached to the upper tank have a downward slope. The higher-density flow is fed to the lower inlet tank and gets an upward velocity before entering the mixing channel. (iii) Two triangular barriers are placed within the mixing channel to impose chaotic advection and perturb the less-mixed flow along the top and bottom surfaces of the channel. (iv) Finally, two outlet channels are incorporated to discard the less-mixed flow. Three-dimensional simulations are carried out to evaluate the performance of the micromixer. Simulations are performed in the absence and presence of the gravitational force to analyse the influence of gravity on the micromixer. Mixing efficiencies of greater than 92 % are achieved using water and a low-density biological solvent as the mixing fluids.

Spectroscopic and model compound studies relevant to wool processing

Describes the development of a cell to hold loose wool fibre, fabric and yarn samples for the collection of Fourier Transform Raman spectra. Then follows a detailed study of reactions of Lanasol (Ciba) dyes with wool, the dyes forming covalent bonds with various amino acids in the fibres.

Relationships between skin follicle characteristics and fibre properties of Suri and Huacaya alpacas and Peppin Merino sheep

We aimed to quantify the number, type and arrangement of skin follicles in Huacaya and Suri alpaca skin and correlate their follicle characteristics with fibre traits of harvested fibre and compared these relationships with those of Merino sheep. Fibre and skin samples were collected from the mid-side of 12 Huacaya alpacas, 24 Suri alpacas and 10 Merino sheep. The mean fibre diameter (MFD ± s.e.) of the Huacaya and Suri were: 35.5 ± 0.9 and 28.3 ± 1.0 μm, respectively. The follicle groups found for alpacas were very different from the normal trio of primary follicles found in sheep and goats. The follicle group of the alpacas consisted of a single primary follicle surrounded by a variable number of secondary follicles. The mean ± s.e. primary follicle density was 3.1 ± 0.3 and 2.7 ± 0.1 follicles/mm² for Huacaya and Suri, respectively. The mean ± s.e. secondary follicle density (SFD) was 13.7 ± 1.2 and 17.5 ± 0.6 follicles/mm² for Huacaya and Suri, respectively. The mean ± s.e. ratio of secondary to primary follicles (S/P ratio) was 5.1 ± 0.5 for the Huacaya and 7.3 ± 0.2 for the Suri alpacas. The sheep had higher S/P ratios and SFD, lower MFD and produced significantly heavier fleeces. The key correlations found between traits in alpacas include a negative correlation between SFD and MFD (r = –0.71, P = 0.001) and a negative correlation between S/P ratio and MFD (r = –0.44, P = 0.003) and a positive correlation between S/P ratio and total follicle density (r = 0.38, P = 0.010). The study revealed that important relationships exist between alpaca skin follicle characteristics and fibre characteristics. It was the number of secondary follicles in a group that imparts density and a corresponding reduced MFD.

An experimental investigation of edge strain and bow in roll forming a V-section

V-sections were roll formed from two grades of steel, and the strain on the top and bottom of the strip near the edge was measured using electrical resistance strain gauges. The channels were bent to a radius of 2 and 15 mm along the centerline. The steel strips were of mild and dual phase steel of yield strength 367 MPa and 597 MPa respectively. The longitudinal bow was measured using a 3-dimensional scanning system. The strain measurements were analysed to determine bending and mid-surface strains at the edge during forming. The peak longitudinal edge strain increased with material yield strength for both profile radii. For the 15 mm radius, the bow was larger in the dual phase steel than in the mild steel. For the 2 mm profile radius, the bow was smaller compared with the 15 mm profile radius and it was similar for both steels. It was observed that the difference between the peak longitudinal edge strain and yield strength to Youngs modulus ratio of the material is an important factor in determining longitudinal bow.

Relationships between wearer assessment and the instrumental measurement of the handle and prickle of knitted wool fabrics

The relationships between wearer-assessed comfort and objectively measured comfort and handle parameters were investigated using 19 pure wool single jersey garments made of single ply yarns. Wearer trials were used to determine prickle discomfort, and whether wearers “liked” the garments. Fabrics then were objectively evaluated using the Wool HandleMeter, which measures seven primary handle attributes; and the Wool ComfortMeter (WCM), to predict a wearer's perception of fabric-evoked prickle. Wearer responses and the relationships within and between objective measurements and the effect of fibre, yarn and fabrics attributes were analysed by general linear modelling. Mean fibre diameter, fibre diameter coefficient of variation, yarn count, fabric thickness, fabric density, fabric mass per unit area and decatising affected one or more handle parameters. The best model for predicting wearer prickle discomfort accounted for 90.9% of the variance and included only terms for the WCM and WCM2. The WCM was a good predictor whereas mean fibre diameter was a poor predictor of whether wearers “liked” garments. Wearer assessment of prickle and whether or not wearers “liked” fabrics were independent of fabric handle assessment. The results indicate that the handle and comfort properties of lightweight, wool jersey fabrics can be quantified accurately using the Wool HandleMeter and the Wool ComfortMeter. For fabric handle, fibre and yarn characteristics were less important than changes in the properties of the fabric.

Fabric handle properties of superfine wool fabrics with different fibre curvature, cashmere content and knitting tightness

The handle properties of single jersey fabrics composed of superfine wools (17 μm) of different fibre curvature (114 vs. 74 °/mm) in blends with cashmere (fibre curvature 49 °/mm) were investigated. There were four blend ratios of cashmere (0, 25, 50, 75%) plus 100% cashmere. Each of the nine fibre blend combinations were replicated three times, and each was knitted into three tightness factors. The 81 fabrics were evaluated using the Wool HandleMeter, which measures seven primary handle attributes and Overall handle, and have been calibrated using a panel of experts and a wide variety of commercial fabrics. Results were analysed by ANOVA and general linear modelling. Tightness factor significantly affected all Wool HandleMeter attribute values, with the effect of tightness factor varying according to handle attribute. The Wool HandleMeter was able to detect differences between fabrics composed of superfine wool differing in fibre curvature, with lower fibre curvature wool fabrics having more preferred Overall handle and softer, looser, cooler, lighter and less dry handle attributes at some or all tightness factors compared with fabrics composed of higher fibre curvature superfine wool. Progressively blending cashmere with wool significantly improved Overall handle, increased soft and smooth handle, reduced dry, heavy and tight handle. Linear regression modelling indicated that fabric mass per unit area explained more than 50% of the variance in overall fabric handle and in combination with variations in fabric thickness and yarn elongation could explain 71% of the variance in Overall handle.

Effects of nitrous oxide on IOP and pupillary diameter in dogs anesthetized with varying concentrations of desflurane

Objective The aim of the present study was to evaluate the effects of nitrous oxide on TOP and pupillary diameter (PD) of dogs anesthetized with varying desflurane concentrations.Animals studied Twenty adult Mongrel dogs were used.Methods They were anesthetized with propofol (10 mg/kg, IV) and maintained with varying concentrations of desflurane (1.6, 1.4, and 1.2 MAC diluted in 100% oxygen (G1) or in 70% nitrous oxide and 30% oxygen (G2) (30 mL/kg/min). TOP was measured by applanation tonometry and horizontal PD was taken with a caliper adjacent to the cornea. Mean arterial pressure (MAP), heart rate (HR), respiratory rate (RR), and end-tidal CO, (etCO(2)) were also measured. All parameters were measured at TO, T30, T45, and T60 time points. One-way repeated measures ANOVA and the t-test were used to assess statistical differences (P < 0.05).Results T30, T45, and T60 TOP measures were Within normal limits for both groups and TOP did not differ between groups at any time. There was a significant decrease in PD in G I between TO and T30, T45 and T60, and also between T30 and T60. PD did not differ between groups. All vital parameters were within normal limits throughout anesthesia.Conclusions Administration of nitrous oxide with desflurane results in maintenance of normal TOP and prevents a decrease in horizontal PD during anesthesia. Therefore, this may be a suitable protocol in dogs undergoing intraocular surgeries that require mydriasis and maintenance of normal TOP.

Air-assisted boom sprayer and spray deposition on bean plants

A possibilidade do desenvolvimento de técnicas de aplicação de produtos fitossanitários mais seguras, com menores volumes de calda, número de aplicações e deriva, aliados à necessidade de se obter melhores níveis de controle dos agentes nocivos às plantas cultivadas, justificam o uso da assistência de ar junto à barra de pulverização. Com o objetivo de avaliar a deposição da pulverização na cultura do feijoeiro (Phaseolus vulgaris), em presença e ausência da assistência de ar junto à barra de pulverização, com diferentes pontas de pulverização e volumes de calda, foi conduzido um experimento em delineamento inteiramente casualizado, utilizando-se como traçador o óxido cuproso. Alvos artificiais (papel filtro com 3 x 3 cm) foram afixados nas superfícies adaxial e abaxial de folíolos posicionados nos terços superior e inferior de plantas, selecionadas ao acaso, distribuídas perpendicularmente ao deslocamento do pulverizador. Após a aplicação do traçador os coletores foram lavados individualmente em solução extratora de ácido nítrico a 1,0 mol L-1. A determinação quantitativa dos depósitos foi realizada com o uso da espectrofotometria de absorção atômica. A assistência de ar junto à barra de pulverização não aumentou a deposição do traçador em folíolos de feijoeiro, aos 48 dias após a emergência da cultura.

Influence of light guide tip used in the photo-activation on degree of conversion and hardness of one nanofilled dental composite

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Toward reliable estimates of seed removal by small mammals and birds in the Neotropics

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Hardening of a dual-cure resin cement using QTH and LED curing units

Objective: This study evaluated the surface hardness of a resin cement (RelyX ARC) photoactivated through indirect composite resin (Cristobal) disks of different thicknesses using either a light- emitting diode (LED) or quartz tungsten halogen (QTH) light source. Material and Methods: Eighteen resin cement specimens were prepared and divided into 6 groups according to the type of curing unit and the thickness of resin disks interposed between the cement surface and light source. Three indentations (50 g for 15 s) were performed on the top and bottom surface of each specimen and a mean Vickers hardness number (VHN) was calculated for each specimen. The data were analyzed using two-way ANOVA and Tukey-Kramer test was used for post-hoc pairwise comparisons. Results: Increased indirect resin disk thickness resulted in decreased mean VHN values. Mean VHN values for the top surfaces of the resin cement specimens ranged from 23.2 to 46.1 (QTH) and 32.3 to 41.7 (LED). The LED curing light source produced higher hardness values compared to the QTH light source for 2- and 3-mm-thick indirect resin disks. The differences were clinically, but not statistically significant. Increased indirect resin disk thickness also resulted in decreased mean VHN values for the bottom surfaces of the resin cement: 5.8 to 19.1 (QTH) and 7.5 to 32.0 (LED). For the bottom surfaces, a statistically significant interaction was also found between the type of curing light source and the indirect resin disk thickness. Conclusions: Mean surface hardness values of resin cement specimens decreased with the increase of indirect resin disk thickness. The LED curing light source generally produced higher surface hardness values.

A dynamical mechanism to explain the top-bottom quark mass hierarchy

We discuss the mass splitting between the the top and bottom quarks in a technicolor scenario. The model proposed here contains a left-right electroweak gauge group. An extended technicolor group and mirror fermions are introduced. The top-bottom quark mass splitting turns out to be intimately connected to the breaking of the left-right gauge symmetry. Weak isospin violation occurs within the experimental limits.