柴达木盆地北缘西段油气运聚动力学研究

Hydrocarbon migration and accumulation are the important process to form reservoirs in sedimentary basins, and their researches are usually very difficult to be done in petroleum geology. In this paper, the west segment of northern margin of the Qaidam Basin was selected as study area. The concept of fault open coefficient, that combines multi-factors dealing with fault sealing, was applied to estimate semi-quantitatively the sealing characteristics of six faults which were considered controlling the hydrocarbon migration and accumulation. The data from boreholes were investigated to appraise the permeable characteristics of lithology combinations upon and beneath the unconformity surface. The result suggests that the basal conglomerates consist frequently the carriers. The data from boreholes and outcrops were collected to describe the sand carrier system. In order to eliminate the influence of inverse activities of the basin that made the formations be very steep, author adopts the phase method to build the basin models: for the steps before Pliocene the recovered true thickness maps were used to build the basin block; for the steps after Pliocene, the structure maps of today were used to build the basin block. During the modeling process, the results were calibrated by various measured data . the modeled results includes the dynamic evolvement course of trap form phase, vitrinite reflectance mature, the source rock expelled hydrocarbon intensity and fluid potential and petroleum plays. Author integrates the source rock expelled hydrocarbon intensity, fluid potential and carrier system and apply the migration technology based on percolation theory to simulate the oil and gas migration and accumulation course in the main accumulation times. The dominant pathways of oil and gas may show clearly the prospect distribution. Based on the hydrocarbon migration characteristics, the main control factors were synthesized, that including the effective source rock distribution, the match relationship of structural trap forming and hydrocarbon expelling from source rocks, the unconformity of Mesozoic and Cenozoic, the structures and the faults movement at Quaternary Finally, the author figures out the prospect plays in the study area.

准噶尔盆地热历史与油气

Based on the temperature data from 196 wells and thermal conductivity measurements of 90 rock samples, altogether 35 heat flow data are obtained. The results show that the Junggar basin is a relatively "cold basin" at present. The thermal gradients vary between 11.6 and 26.5 ℃/km, and the thermal conductivity change from 0.17 to 3.6 W/mK. Heat flow ranges from 23.4 to 53.7 mW/m~2 with a mean of 42.3 ± 7.7 mW/m~2. The heat flow pattern shows that heat flow is higher on the uplifts and lower on the depressions. The overall low present-day heat flow in the Junggar Basin reflects its stable cratonic basement and Cenozoic tectonothermal evolution characterized by lithospheric thickening, thrust and fault at shallow crust as well as consequently quick subsidence during the Late Cenozoic. The study of the basin thermal history, which is one of the important content of the basin analysis, reveals not only the process of the basin's tectonothermal evolution, but also the thermal evolution of the source rocks based on the hydrocarbon generation models. The latter is very helpful for petroleum exploration. The thermal history of the Junggar basin has been reconstructed through the heat flow based method using the VR and Fission track data. The thermal evolutions of main source rocks (Permian and Jurassic) and the formations of the Permian and the Jurassic petroleum systems as well as the influences of thermal fields to petroleum system also have been discussed in this paper. Thermal history reconstruction derived from vitrinite reflectance data indicates that the Paleozoic formations experienced their maximum paleotemperature during Permian to Triassic with the higher paleoheat flow of around 70-85 mW/m~2 and the basin cooled down to the present low heat flow. The thermal evolution put a quite important effect on the formation and evolution of the petroleum system. The Jurassic petroleum system in the Junggar basin is quite limited in space and the source rocks of Middle-Lower Jurassic entered oli-window only along the foreland region of the North Tianshan belt, where the Jurassic is buried to the depth of 5-7 km. By contrast, the Middle-Lower Permian source rocks have initiated oil and gas generation in latter Permian to Triassic, and the major petroleum systems, like Mahu-West Pen 1 Well, was formed prior to Triassic when later Paleozoic formation reached the maximum paleotemperature.

柴达木盆地北缘地区油气成藏过程模拟与含油气系统评价

As an important part of petroleum exploration areas in the west of China, the north part of Qaidam basin is very promising in making great progress for petroleum discovery. But there are still many obstacles to overcome in understanding the process of petroleum formation and evaluation of oil & gas potential because of the complexity of geological evolution in the study area. Based upon the petroleum system theory, the process of petroleum formation is analyzed and the potential of oil & gas is evaluated in different petroleum systems by means of the modeling approach. The geological background for the formation of petroleum systems and the consisting elements of petroleum systems are described in detail. The thickness of strata eroded is estimated by means of vitrinite reflectance modeling, compaction parameter calculating and thickness extrapolating. The buried histories are reconstructed using the transient compaction model, which combines of forward and reverse modeling. The geo-history evolution consists of four stages - sedimentation in different rates with different areas and slow subsidence during Jurassic, uplifting and erosion during Cretaceous, fast subsidence during the early and middle periods of Tertiary, subsidence and uplifting in alternation during the late period of Tertiary and Quaternary. The thermal gradients in the study area are from 2.0 ℃/100m to 2.6 ℃/100m, and the average of heat flow is 50.6 mW/m~2. From the vitrinite reflectance and apatite fission track data, a new approach based up Adaptive Genetic Algorithms for thermal history reconstruction is presented and used to estimate the plaeo-heat flow. The results of modeling show that the heat flow decreased and the basin got cooler from Jurassic to now. Oil generation from kerogens, gas generation from kerogens and gas cracked from oil are modeled by kinetic models. The kinetic parameters are calculated from the data obtained from laboratory experiments. The evolution of source rock maturation is modeled by means of Easy %Ro method. With the reconstruction of geo-histories and thermal histories and hydrocarbon generation, the oil and gas generation intensities for lower and middle Jurassic source rocks in different time are calculated. The results suggest that the source rocks got into maturation during the time of Xiaganchaigou sedimentation. The oil & gas generation centers for lower Jurassic source rocks locate in Yikeyawuru sag, Kunteyi sag and Eboliang area. The centers of generation for middle Jurassic source rocks locate in Saishenteng faulted sag and Yuka faulted sag. With the evidence of bio-markers and isotopes of carbonates, the oil or gas in Lenghusihao, Lenghuwuhao, Nanbaxian and Mahai oilfields is from lower Jurassic source rocks, and the oil or gas in Yuka is from middle Jurassic source rocks. Based up the results of the modeling, the distribution of source rocks and occurrence of oil and gas, there should be two petroleum systems in the study area. The key moments for these two petroleum, J_1-R(!) and J_2-J_3, are at the stages of Xiaganchaigou-Shangyoushashan sedimentation and Xiayoushashan-Shizigou sedimentation. With the kinetic midels for oil generated from kerogen, gas generated from kerogen and oil cracked to gas, the amount of oil and gas generated at different time in the two petroleum systems is calculated. The cumulative amount of oil generated from kerogen, gas generated from kerogen and gas cracked from oil is 409.78 * 10~8t, 360518.40 * 10~8m~3, and 186.50 * 10~8t in J_1-R(!). The amount of oil and gas generated for accumulation is 223.28 * 10~8t and 606692.99 * 10~8m~3 in J_1-R(!). The cumulative amount of oil generated from kerogen, gas generated from kerogen and gas cracked from oil is 29.05 * 10~8t, 23025.29 * 10~8m~3 and 14.42 * 10~8t in J_2-J_3 (!). The amount of oil and gas generated for accumulation is 14.63 * 10~8t and 42055.44 * 10~8m~3 in J_2-J_3 (!). The total oil and gas potential is 9.52 * 10~8t and 1946.25 * 10~8m~3.

南海北部大陆边缘盆地热演化史及其与油气关系

This thesis focuses on the present-day thermal field features, evolution and their connections to hydrocarbon generation of the three continental margin basins-the Yinggehai (Yingge Sea), Qiongdongnan(southeast Qiong), and Pear River Mouth basins-in northern South China Sea, based on available data from drillings, loggings, seismic cross-sections, BHTs, thermal indicators (Ro%, inclusion, etc) and geopressure measurements. After studying of present-day distribution of geothermal field and thermal disturbance of fluid in the sedimentary strata, the author discovered that the distribution of gas fields in Yinggehai Basin are closely related to the distribution of anomalously high thermal gradient area, whereas it is not the case for the Pear River Mouse Basin. And detailed processing of the fluid inclusion data indicates that geothermal fluids activated frequently in this area, and they may mainly be derived upward from the overpressure and hydrocarbon-generating beds, 3000-4500 m in depth. Therefore, the abnormal gradients in sedimentary beds were mainly caused by the active geothermal fluids related to hydrocarbon migrating and accumulating in this area. Because of the effect of overpressure retarding on vitrinite reflectance, the thermal indicators for thermal history reconstruction should be assessed before put into use. Although some factors, such as different types of kerogen, heating ratio, activities of thermal fluids and overpressure, may have effects on the vitrinite reflectance, under the circumstance that thermal fluids and overpressure co-exist, overpressure retarding is dominant. And the depth and correction method of overpressure retarding were also determined in this paper. On the basis of reviewing the methods of thermal history studies as well as existing problems, the author believes that the combination of thermal-indicator-inversion and tectono-thermal modeling is an effective method of the thermal history reconstruction for sedimentary basins. Also, a software BaTherMod for modeling thermal history of basins was successfully developed in this work. The Yinggehai Basin has been active since Tertiary, and this was obviously due to its tectonic position-the plate transition zone. Under the background of high thermal flow, long-term quick subsidence and fluid activities were the main reasons that lead to high temperature and overpressure in this basin. The Zhujiangkou Basin, a Tertiary fault-basin within the circum-Pacific tectonic realm, was tectonically controlled by the motion of the Pacific Plate and resembles the other petroliferous basins in eastern China. This basin developed early, and characterized intensive extension in the early stage and weak activity in the later stage of its development. Whereas the Qiongdongnan Basin was in a weak extension early and intensity of extension increased gradually. The relative geographical locations and the extensional histories of three basins ilustrate that the northern continental margin of South China Sea spread from south to north. On the other hand, the Qiongdongnan and Yinggehai Basins may have been controlled by the same tectonic regime since later Tertiary, whereas the Zhujiangkou Basin was not meaningfully influenced. So, the tectono-thermal evolution character of the Qiongdonnan basin should be closely to the other two. It may be concluded that the three basins have been developed within the active continental margin since Tertiary, and the local lithosphere might undergo intensive extension-perhaps two or three times of episodic extension occurred. Extension lead to large tectonoc subsidence and extreme thick Tertiary sediments for hydrocarbon generation in the basins. In response to the periodic extension of the basins, the palaeothermal flow were also periodical. The three basins all have the characteristics of multi-phase thermal evolutions that is good for oil-gas generation. And the overpressure expands the depth range of oil-gas habitat, which is meaningful to petroleum exploration in this region.

东海陆架盆地西南部烟囱构造与油气运聚关系研究

In recent years, chimney structure has been proved one of important indicators and a useful guide to major petroleum fields exploration through their exploration history both at home and abroad. Chimney structure, which has been called "gas chimney" or "seismic chimney", is the special fluid-filled fracture swarm, which results from the boiling of active thermal fluid caused by abruptly decreasing of high pressure and high temperature in sedimentary layers of upper lithosphere. Chimney structure is well developed in continental shelf basin of East China Sea, which indicates the great perspectives of petroleum resources there. However, the chimney structure also complicated the petroleum accumulation. So the study of chimney structure on its formation, its effect on occurrence and distribution of petroleum fields is very important not only on theoretical, but also on its applied research. It is for the first time to make a clear definition of chimney structure in this paper, and the existence and practical meaning of chimney structure are illustrated. Firstly, on the viewpoint of exploration, this will amplify exploration area or field, not only in marine, but also on continent. Secondly, this is very important to step-by-step exploration and development of petroleum fields with overpressure. Thirdly, this will provide reference for the study on complex petroleum system with multi-sources, commingled sources and accumulation, multi-stage accumulations, and multi-suits petroleum system in the overlay basin. Fourthly, when the thermal fluid enters the oceanic shallow layer, it can help form gas hydrate under favorable low-temperature and high-pressure conditions. Meanwhile, the thermal fluid with its particular component and thermal content will affect the physical, chemical and ecological environments, which will help solving the problem of global resources and environment. Beginning from the regional tectonic evolution characteristics, this paper discussed the tectonic evolution history of the Taibei depression, then made an dynamical analysis of the tectonic-sedimentary evolution during the Mesozoic and Cenozoic for the East China Sea basin. A numerical model of the tectonic-thermal evolution of the basin via the Basin-Mod technique was carried out and the subsidence-buried history and thermal history of the Taibei depression were inverse calculated: it had undergone a early rapid rift and sag, then three times of uplift and erosion, and finally depressed and been buried. The Taibei depression contains a huge thick clastic sedimentary rock of marine facies, transitional facies and continental facies on the complex basement of ante-Jurassic. It is a part of the back-arc rifting basins occurred during the Mesozoic and Cenozoic. The author analyzed the diagenesis and thermal fluid evolution of this area via the observation of cathodoluminescence, scanning electron microscope and thin section, taking advantage of the evidences of magma activities, paleo-geothermics and structural movement, the author concluded that there were at least three tectonic-thermal events and three epochs of thermal-fluid activities; and the three epochs of thermal-fluid activities were directly relative to the first two tectonic-thermal events and were controlled by the generation and expulsion of hydrocarbon in the source rock simultaneously. Based on these, this paper established the corresponding model between the tectonic-thermal events and the thermal-fluid evolution of the Taibei Depression, which becomes the base for the study on the chimney structures. According to the analyses of the gas-isotope, LAM spectrum component of fluid inclusion, geneses of CO_2 components and geneses of hydrocarbon gases, the author preliminarily verified four sources of the thermal fluid in the Taibei Depression: ① dehydration of mud shale compaction, ② expulsion of hydrocarbon in the source rock; ③ CO_2 gas hydro-thermal decomposition of carbonatite; ④magma-derived thermal fluid including the mantle magma water and volatile components (such as H_2O, CO_2, H_2S, SO_2, N_2 and He etc.). On the basis of the vitrinite reflectance (Ro), homogenization temperature of fluid inclusion, interval transit time of major well-logging, mud density of the wells, measured pressure data and the results of previous studies, this paper analyzed the characteristics of the geothermal fields and geo-pressure fields for the various parts in this area, and discussed the transversal distribution of fluid pressure. The Taibei depression on the whole underwent a temperature-loss process from hot basin to cold basin; and locally high thermal anomalies occurred on the regional background of moderate thermal structure. The seal was primarily formed during the middle and late Paleocene. The overpressured system was formed during the middle and late Eocene. The formation of overpressured system in Lishui Sag underwent such an evolutionary process as "form-weaken-strengthen-weaken". Namely, it was formed during the middle and late Eocene, then was weakened in the Oligocene, even partly broken, then strengthened after the Miocene, and finally weakened. The existence of the thermal fluid rich in volatile gas is a physical foundation for the boiling of the fluid, and sharply pressure depletion was the major cause for the boiling of the fluid, which suggests that there exists the condition for thermal fluid to boil. According to the results of the photoelastic simulation and similarity physical experiments, the geological condition and the formation mechanism of chimnestructures are summarized: well compartment is the prerequisite for chimney formation; the boiling of active thermal fluid is the original physical condition for chimney formation; The local place with low stress by tension fault is easy for chimney formation; The way that thermal fluid migrates is one of the important factors which control the types of chimney structures. Based on where the thermal fluid come from and geometrical characteristics of the chimney structures, this paper classified the genetic types of chimney structures, and concluded that there existed three types and six subtypes chimney structures: organic chimney structures generated by the hydrocarbon-bearing thermal fluid in middle-shallow layers, inorganic and commingling-genetic chimney structures generated by thermal fluid in middle-deep layers. According to the seismic profiles interpretations, well logging response analysis and mineralogical and petrological characteristics in the study area, the author summarized the comprehensive identification marks for chimney structures. Especially the horizon velocity analysis method that is established in this paper and takes advantage of interval velocity anomaly is a semi-quantitative and reliable method of chimney structure s identification. It was pointed out in this paper that the occurrence of the chimney structures in the Taibei depression made the mechanism of accumulation complicated. The author provided proof of episodic accumulation of hydrocarbon in this area: The organic component in the boiling inclusion is the trail of petroleum migration, showing the causality between the boiling of thermal fluid and the chimney structures, meanwhile showing the paroxysmal accumulation is an important petroleum accumulation model. Based on the evolutionary characteristics of various types of chimney structures, this paper discussed their relationships with the migration-accumulation of petroleum respectively. At the same time, the author summarized the accumulating-dynamical models associated with chimney structures. The author analyzed such accumulation mechanisms as the facies state, direction, power of petroleum migration, the conditions of trap, the accumulation, leakage and reservation of petroleum, and the distribution rule of petroleum. The author also provides explanation for such practical problems the existence of a lot of mantle-derived CO_2, and its heterogeneous distribution on plane. By study on and recognition for chimney structure, the existence and distribution of much mantle-derived CO_2 found in this area are explained. Caused by tectonic thermal activities, the deep magma with much CO_2-bearing thermal fluid migrate upward along deep fault and chimney structures, which makes two wells within relatively short distance different gas composition, such as in well LF-1 and well LS36-1-1. Meanwhile, the author predicted the distribution of petroleum accumulation belt in middle-shallow layer for this area, pointed out the three favorable exploration areas in future, and provided the scientific and deciding references for future study on the commingling-genetic accumulation of petroleum in middle-deep layer and the new energy-gas hydrate.

生物－热催化过渡带沉积成岩演化及其成烃作用研究

The biothermocatalytic transitional zone gas is a new type of natural gas genetic theory, and also an clean, effective and high quality energy with shallow burial depth, wide distribution and few investment. Meanwhile, this puts biothermocatalytic transitional zone gas in important position to the energy resource and it is a challenging front study project. This paper introduces the concept, the present situation of study and developmental trend about biothermocatalytic transitional zone gas in detail. Then by using heat simulating of source rocks and catalysis mechanism analysis in the laboratory and studying structural evolution, sedimentation, diagenesis and the conditions of accumulation formation and so on, this paper also discusses catalytic mechanism and evolutionary model of the biothermocatalytic transitional zone gas formation, and establishes the methods of appraisal parameter and resources prediction about the biothermocatalytic transitional zone gas. At last, it shows that geochemical characteristics and differentiated mark of the biothermocatalytic transitional zone gas, and perfect natural gas genetic theory, and points out the conditions of accumulation formation, distribution characteristics and potential distribution region on the biothermocatalytic transitional zone gas m China. The paper mainly focuses on the formation mechanism and the resources potential about the biothermocatalytic transitional zone gas. Based on filed work, it is attached importance to a combination of macroscopic and microcosmic analysis, and the firsthand data are obtained to build up framework and model of the study by applying geologic theory. Based on sedimentary structure, it is expounded that structural actions have an effect on filling space and developmental cource of sediments and evolution of source rocks. Carried out sedimentary environment, sequence stratigraphy, sedimentary system and diagenesis and so on, it is concluded that diagenesis influences developmental evolution of source rocks, and basic geologic conditions of the biothermocatalytic transitional zone gas. Applying experiment simulating and catalytic simulating as well as chemical analysis, catalytic mechanism of clay minerals is discussed. Combined diagenecic dynamics with isotope fractionation dynamics, it is established that basis and method of resource appraisal about the biothermocatalytic transitional zone gas. All these results effectively assess and predict oil&gas resources about the biothermocatalytic transitional zone gas-bearing typical basin in China. I read more than 170 volumes on the biothermocatalytic transitional zone gas and complete the dissertation' summary with some 2.4 ten thousand words, draw up study contents in some detail and set up feasible experimental method and technologic course. 160 pieces of samples are obtained in oilfield such as Liaohe, Shengli, Dagang and Subei and so on, some 86 natural gas samples and more than 30 crude oil samples. Core profiles about 12 wells were observed and some 300 geologic photos were taken. Six papers were published in the center academic journal at home and abroad. Collected samples were analysised more than 1000 times, at last I complete this dissertation with more than 8 ten thousand words, and with 40 figures and 4 plates. According to these studies, it is concluded the following results and understandings. 1. The study indicates structural evolution and action of sedimentary basin influence and control the formation and accumulation the biothermocatalytic transitional zone gas. Then, the structural action can not only control accommodation space of sediments and the origin, migration and accumulation of hydrocarbon matters, but also can supply the origin of energy for hygrocarbon matters foramtion. 2. Sedimentary environments of the biothermocatalytic transitional zone gas are lake, river and swamp delta- alluvial fan sedimentary systems, having a warm, hot and humid climate. Fluctuation of lake level is from low to high., frequency, and piling rate of sedimentary center is high, which reflect a stable depression and rapidly filling sedimentary course, then resulting in source rocks with organic matter. 3. The paper perfects the natural gas genetic theory which is compound and continuous. It expounds the biothermocatalytic transitional zone gas is a special gas formation stage in continuous evolutionary sequence of organic matter, whose exogenic force is temperture and catalysis of clay minerals, at the same time, having decarbxylation, deamination and so on. 4. The methodology is established which is a combination of SEM, TEM and Engery spectrum analysis to identify microstructure of crystal morphology about clay minerals. Using differential thermal-chromatographic analysis, it can understand that hydrocarbon formation potential of different typies kerogens and catalytic method of all kinds of mineral matrix, and improve the surface acidity technology of clay minerals measured by the pyridine analytic method. 5. The experiments confirm catalysis of clay minerals to organic matter hygrocarbon formation. At low temperature (<300 ℃), there is mainly catalysis of montmorillonite, which can improve 2-3 times about produced gas of organic matters and the pyrolyzed temperature decreased 50 ℃; while at the high temperature, there is mainly catalysis of illite which can improve more than 2 times about produced gas of organic matters. 6. It is established the function relationship between organic matter (reactant) concentration and temperature, pressure, time, water and so on, that is C=f (D, t). Using Rali isotope fractionation effect to get methane isotope fractionation formula. According to the relationship between isotope fractionation of diagenesis and depth, and combined with sedimentary rate of the region, it is estimated that relict gas of the biothermocatalytic transitional zone gas in the representative basin. 7. It is revealed that hydrocarbon formation mechanism of the biothermocatalytic transitional zone gas is mainly from montmorillonite to mixed minerals during diagenesis. In interlayer, a lot of Al~(3+) substitute for Si~(4+), resulting in a imbalance between surface charge and interlayer charge of clay minerals and the occurrence of the Lewis and Bronsted acid sites, which promote to form the carbon cation. The cation can form alkene or small carbon cation. 8. It is addressed the comprehensive identification mark of the biothermo - catalytic transitional zone gas. In the temproal-spatial' distribution, its source rocks is mainly Palaeogene, secondly Cretaceous and Jurassic of Mesozoic, Triassic, having mudy rocks and coal-rich, their organic carbon being 0.2% and 0.4% respectively. The vitrinite reflection factor in source rocks Ro is 0.3-0.65%, a few up to 0.2%. The burial depth is 1000-3000m, being characterized by emerge of itself, reservoir of itself, shallow burial depth. In the transitional zone, from shallow to deep, contents of montmorillonites are progressively reduced while contents of illites increasing. Under SEM, it is observed that montmorillonites change into illite.s, firstly being mixed illite/ montmorillonite with burr-like, then itlite with silk-like. Carbon isotope of methane in the biothermocatatytic transitional zone gas , namely δ~(13)C_1-45‰- -60 ‰. 9. From the evolutionary sequence of time, distribution of the biothermocatalytic transitional zone gas is mainly oil&gas bearing basin in the Mesozoic-Neozoic Era. From the distribution region, it is mainly eastern stuctural active region and three large depressions in Bohaiwang basin. But most of them are located in evolutionary stage of the transitional zone, having the better relationship between produced, reservoir and seal layers, which is favorable about forming the biothermocatalytic transitional zone gas reservoir, and finding large gas (oil) field.

塔里木盆地塔中地区寒武-奥陶系烃源岩古地温及成烃演化史研究

The present maturity of Cambrian and Ordovician source rocks in Tazhong area, Tarim basin, is studied using several organic petrology methods and conodont CAI method. The highest palaeotemperature that the Cambrian-Ordovician undergone is revealed by Laser Roman Microprobe (LRM) analysis and by simulating experiment of the kerogen chemical kinetics. In according to all above study, the thermal history of Cambrian and Ordovician is reconstructed based on numerical simulating approaches. The characteristics of secondary hydrocarbon generating are studied by inclusions analysis. The reflectances of the samples in the drills located in Tazhong area show that the maturities of Cambrian source rocks are in the stages of condense oil-dry gas, and that of Ordovician source rocks range from peak of oil generating to wet gas stage. The palaeotemperature data of Cambrian-Orovician source rocks from well Tacan 1, based on LRM analysis, are in coincidence with that from other methods. Also are the palaeotemperature data of Cambrian-Orovician source rocks in well Tacan 1 based on the simulating experiments of kerogen pyrolysis, similar to the homogenization temperatures of inclusions in the source rocks. Aaccording to the vitrinite inflectance data of the TZ12 well and Tacan 1 well, the paleotemperature gradients are analysized and reconstructed. These data show that the paleotemperature gradient in Tazhong area was the highest during Cambrian-Ordovician period, it was up to 3.5°C/100m. Following, the temperature gradient descended gradually and it reached to the lowest at present (2.2°C/100m). The histories of maturation and hydrocarbon generation of Cambrian and Ordovician source rocks in Tazhong area are researched systematically and quantitatively, the results show that periods of oil generation from Cambrian and Ordovician source rocks lasted for a long time from Ordovician to Carbonferious periods because the central Cambrian stratum in the north slope of Tazhong area is buried differently in depth. The top of the Cambrian entered into the peak of oil generation in middle-late Ordovician, and most area of the north slope of Tazhong area entered into the peak of oil generation in Carbonferious period, and on the uplift belt some of source rocks entered into the peak of oil generation in Permian period. In early Devonian, the central of the Lower Ordovician source rocks near the Manjiaer depression reached the peak of oil generation and near the top of the Tazhong uplift did not reached the peak of oil generation until early Cretaceous. The middle-upper Ordovician entered into the peak of oil generation in early-middle Jurassic. The time of the middle-upper Ordovician in the top of the uplift belt entering into the peak of oil generation was delayed, because the source rock was buried shallowly, and it did not reached the peak of oil generation until middle Cretaceous. Middle-upper Ordovician in the top of the north slope has been in the peak of oil generation now, it is consistent with the maturity (1.0-1.2%Ro) of the source rocks. The characteristics of the inclusions formed by kerogens are different from that by crystal-enclosed organic matters(OM) during secondary hydrocarbon generation of Cambrian and Ordovician source rocks. The secondary hydrocarbon generation mainly occurred in Mesozoic-Cenozoic period, in an area of about 9000km2 in the north slope. The intensity of the secondary hydrocarbon generation of Cambrian and Ordovician is up to 21kg/torg and 36kg/torg) respectively. Using the staged gas chromatography, the high-over maturated carbonate source rocks are analysized to release the adsorbed OM, inclusions OM and crystal-enclosed OM, respectively, and to evaluate their relative contributions to secondary hydrocarbon generation. The three periods of oil and gas migration and petroleum pools formation in Tazhong area are determined according to organic inclusions and solid bitumen.

中国东海陆架盆地构造-热演化研究

East China Sea Shelf Basin (ECSSB), as a basin with prospect of oil & gas resource and due to its special geological location on the west margin of the west Pacific, attracts a lot of attention from many geologists in the world.Based on systematic temperature measurements, bottom hole temperature (BHT) and the oil temperature data, the geothermal gradients in the ECS SB are calculated and vary from 25 to 43°C/km, with a mean of 32.7°C/km. The geothermal gradient in Fuzhou Sag has the higher value(40.6°C/km) in Taibei Depression than that in others. The lower value (27.2 °C/km) occurs in in Xihu Depression. The middle values occurs in Jiaojiang and Lishui sags in Taibei Depression with a mean value of 34.8 °C/km. Incorporated with the measured thermal conductivity, heat flow values show that the ECSSB is characterized by present-day heat flow around 70.6mW/m2, varying between 55 and 88 mW/m2. No significant difference in heat flow is observed between the Xihu and the Taibei Depressions. These heat flow data suggest that the ECSSB is geothermally not a modem back-arc basin.Applying the paleogeothermal gradient based method, thermal history is reconstructed using vitrinite reflectance (VR) and apatite fission track (AFT) data. The results suggest that the thermal history was different in the Taibei and the Xihu depressions. Paleo-heat flow values when the pre-Tertiary formations experienced their maximum temperature at the end of the Paleocene reached a mean of 81 mW/m2 in the Taibei Depression, much higher than the present-day value. The lower Tertiary sediments in the Xihu Depression experienced maximum temperatures at the end of Oligocene and reached a mean paleo-heat flow value of 83.4 mW/m2. The time, when the paleo-heat flow reached the maximum value, suggests that the ECSSB rifted eastward.Tectonic subsidence analysis shows that the timing of the major rifting episode was different across the ECSSB. The rifting occurred from the Late Cretaceous to the early Eocene in the Taibei Depression, followed by thermal subsidence from the late Eocene to the end of Miocene. In contrast, in the Xihu Depression the initial subsidence lasted until the early Miocene and thermal subsidence to the end of Miocene. From Pliocene to the present, an accelerated subsidence took place all along the West Pacific margin of the east Asia.The thermal lithosphere thickness is determined by temperature profile in the lithosphere, the mantle adiabat or the dry basalt solidus. It indicates that the thermal lithosphere reached the thinnest thickness at the end of Eocene in the Taibei Depression and the end of Oligocene in the Xihu Depression, respectively, corresponding with a value of 57-66km and 56-64km. In Taibei Depression, the lithosphere thickness decreased 16-22km from the end of Mesozoic to Paleocene. After Paleocene, the thickness increased 13-16km and reached 71-79 km at present-day. In Xihu Depression, From the end of Oligocene to present-day, the thickness increased 10-13km and reached 69-76km at present-day. The evolution of the lithosphere thickness is associated closely with the lithosphere stretching.Combining the reconstructed thermal history and the burial history, the maturation of the Jurassic oil-source rock shows that the main hydrocarbon generation phase was in the mid-Jurassic and a secondary hydrocarbon generation occurred at the end of Paleocene. The secondary generation was controlled mainly by the tectono-thermal background during the Paleocene.

句容海安区块热史、成烃史与二次生烃

Jurong -Hai'an block of lower Yangtz area is one of the important petroleum exploration area among the residual marine basins in the south China. In the history of the basin's evolution, the strongly compressing, napping, folding and deforming during Indosinian to Yanshan epoch resulted in destruction of the early formed petroleum pool. Therefore, the strategy exploration of the secondary hydrocarbon generation and later formation of petroleum pool was brought forward for petroleum exploration and planning in the study area..On the basis of tectonic and sedimentary as well as present-day thermal regime evolution, using vitrinite reflectance and apatite fission track data and the paleo-heat flow based method, the basin's thermal history is reconstructed and hence the strata's temperature history are obtained. In addition, the maturation histories of the main four sets of marine hydrocarbon source rocks in the block are calculated. Furthermore, taking the maturity in the end of early Cretaceous as the original maturity and according to the formulas fitted by the secondary hydrocarbon generation model, the secondary hydrocarbon generation potential of the four sets of source rock is evaluated.The results of thermal history reconstruction show that Jurong-Hai'an block was under an uniform thermal setting during the Caledonian to Hercynian period and characterized by middle heat flow (52~57rnW/ m2). The uniform thermal setting was divided during and after Indosinian to Yanshan epoch. Wuwei area of southern Anhui province was under the high heat flow setting(~90 mW/m2)between 236Ma and 137Ma; Jurong area of southern Jiangsu ,Huangqiao area and Subei basin reached its maximum heat flow of 90,84 and 78-82 mW/m2 at 101Ma,157Ma and 56Ma respectivelyThe study of secondary hydrocarbon generation shows that the upper Paleozoic and Triassic source rocks have excellent secondary hydrocarbon generation potential. Silurian source rock posses some secondary hydrocarbon generation. Cambrian source rock, however, nearly has no secondary hydrocarbon generation. Overall there are no advantages of secondary hydrocarbon generation in the southern area of Jiansu. The intensity of secondary hydrocarbon generation in North Jiangsu basin is definitely better than that in the southern area of Jiangsu.

Contribuição ao estudo petrográfico e geoquímico dos carvões da jazida de Chico Lomã Santo Antônio da Patrulha

São apresentados os resultados dos estudos petrográfico e geoquímico dos carvões da jazida de Chico Lomã, localizada no município de Santo Antônio da Patrulha, no nordeste do Rio Grande da Sul, situada entre as jazidas de Morungava (limite oeste) e Santa Terezinha (limite leste). Na sondagem estudada - 02-TG-88-RS - foram identificadas 7 camadas e 5 leitos de carvão. Entre estes, apenas as camadas E e F apresentam suficiente extensão lateral para serem consideradas economicamente exploráveis. Os carvões são ricos em matéria mineral, constituída, principalmente, de argila. O grupo maceral mais freqüente é o da vitrinita. No que diz respeito aos microlitotipos, ocorre, em geral, o predomínio de carbominerita. Foram identificadas 3 associações de microlitotipos, determinando a existência das seguintes faciologias: ambiente telmático (predomínio de vitrita-clarita), limo-telmático (predomínio de carbargilita-vitrita) e límnico (predomínio de carbargilita-durita-trimacerita). Os carvões apresentam rank que varia de betuminoso alto volátil C/sub-betuminoso A a betuminoso alto volátil A (ASTM). A utilização tecnológica dos carvões das camadas E e F, na siderurgia, pode ser sugerida, mesmo considerando-se seu elevado teor em cinza, desde que sejam submetidos a processos de beneficiamento. Em relação aos argilo-minerais, constatou-se a presença de caolinita, aparentemente relacionada ao conteúdo da matéria orgânica, e do interestratificado ilita-montmorilonita, provavelmente de origem detrítica. Foram identificados 3 grupos de elementos traços : associados à fração orgânica (Co, Ge, Ni, V e Zr), elementos intermediários (Cr, Cu e Sr) e associados à fração inorgânica (B, Ba e Ga). Observou-se, também, que os elementos do primeiro grupo, de maneira geral, se enriquecem nos litotipos com maior conteúdo de vitrênio, ao contrário dos elementos do último grupo que tendem a se enriquecer no carvão fosco e nos folhelhos. Os estudos realizados indicam um paleoambiente de água doce, no qual, provavelmente, tenham ocorrido pequenas ingressões marinhas entre as fases de formação de turfa.

Combustion of coal, bagasse and blends thereof Part I: Emissions from batch combustion of fixed beds of fuels

Batch combustion of fixed beds of coal, bagasse and blends thereof took place in a pre-heated two-stage electric laboratory furnace, under high-heating rates. The average input fuel/air equivalence ratios were similar for all fuels. The primary and secondary furnace temperatures were varied from 800 degrees C to 1000 degrees C. The effects of fuel blending, combustion staging, and operating furnace temperatures on the emissions from the two fuels were assessed. Furnace effluents were analyzed for carbon dioxide and for products of incomplete combustion (PIC) including CO, volatile and semi-volatile hydrocarbons, as well as particulate matter. Results showed that whereas CO2 was generated during both the observed sequential volatile matter and char combustion phases of the fuels, PICs were only generated during the volatile matter combustion phase. CO2 emissions were the highest from coal, whereas CO and other PIC emissions were the highest from bagasse. Under this particular combustion configuration, combustion of the volatile matter of the blends resulted in lower yields of PIC, than combustion of the volatiles of the neat fuels. Though CO and unburned hydrocarbons from coal as well as from the blends did not exhibit a clear trend with furnace temperature, such emissions from bagasse clearly increased with temperature. The presence of the secondary furnace (afterburner) typically reduced PIC, by promoting further oxidation of the primary furnace effluents. (C) 2012 Elsevier Ltd. All rights reserved.

Thermochronologic and geodynamic evolution of the Pontides: Sakarya terrane (Karakaya Complex) and Istanbul terrane, Turkey.

An integrated array of analytical methods -including clay mineralogy, vitrinite reflectance, Raman spectroscopy on carbonaceous material, and apatite fission-track analysis- was employed to constrain the thermal and thermochronological evolution of selected portions of the Pontides of northern Turkey. (1) A multimethod investigation was applied for the first time to characterise the thermal history of the Karakaya Complex, a Permo-Triassic subduction-accretion complex cropping out throughout the Sakarya Zone. The results indicate two different thermal regimes: the Lower Karakaya Complex (Nilüfer Unit) -mostly made of metabasite and marble- suffered peak temperatures of 300-500°C (greenschist facies); the Upper Karakaya Complex (Hodul and the Orhanlar Units) –mostly made of greywacke and arkose- yielded heterogeneous peak temperatures (125-376°C), possibly the result of different degree of involvement of the units in the complex dynamic processes of the accretionary wedge. Contrary to common belief, the results of this study indicate that the entire Karakaya Complex suffered metamorphic conditions. Moreover, a good degree of correlation among the results of these methods demonstrate that Raman spectroscopy on carbonaceous material can be applied successfully to temperature ranges of 200-330°C, thus extending the application of this method from higher grade metamorphic contexts to lower grade metamorphic conditions. (2) Apatite fission-track analysis was applied to the Sakarya and the İstanbul Zones in order to constrain the exhumation history and timing of amalgamation of these two exotic terranes. AFT ages from the İstanbul and Sakarya terranes recorded three distinct episodes of exhumation related to the complex tectonic evolution of the Pontides. (i) Paleocene - early Eocene ages (62.3-50.3 Ma) reflect the closure of the İzmir-Ankara ocean and the ensuing collision between the Sakarya terrane and the Anatolide-Tauride Block. (ii) Late Eocene - earliest Oligocene (43.5-32.3 Ma) ages reflect renewed tectonic activity along the İzmir-Ankara. (iii) Late Oligocene- Early Miocene ages reflect the onset and development of the northern Aegean extension. The consistency of AFT ages, both north and south of the tectonic contact between the İstanbul and Sakarya terranes, suggest that such terranes were amalgamated in pre-Cenozoic times. (3) Fission-track analysis was also applied to rock samples from the Marmara region, in an attempt to constrain the inception and development of the North Anatolian Fault system in the region. The results agree with those from the central Pontides. The youngest AFT ages (Late Oligocene - early Miocene) were recorded in the western portion of the Marmara Sea region and reflect the onset and development of northern Aegean extension. Fission-track data from the eastern Marmara Sea region indicate rapid Early Eocene exhumation induced by the development of the İzmir-Ankara orogenic wedge. Thermochronological data along the trace of the Ganos Fault –a segment of the North Anatolian Fault system- indicate the presence of a tectonic discontinuity active by Late Oligocene time, i.e. well before the arrival of the North Anatolian Fault system in the area. The integration of thermochronologic data with preexisting structural data point to the existence of a system of major E-W-trending structural discontinuities active at least from the Late Oligocene. In the Early Pliocene, inception of the present-day North Anatolian Fault system in the Marmara region occurred by reactivation of these older tectonic structures. 


(Table 1) Maceral composition and organic carbon chemistry of ODP Leg 104 samples

The Cenozoic sediments sampled in ODP Leg 104 on the Vøring Plateau show a distinct variability of the total organic carbon content (TOC) and the accumulation rates of TOC. Based on the geochemical and organic-petrographic characterization of the sedimentary organic matter (OM), the allochthonous and autochthonous proportion of the OM could be quantified. The results clearly demonstrate that high TOC percentages and TOC accumulation rates in Cenozoic sediment sections display a generally high input of allochthonous organic matter. Oxidized and partly well-rounded organic particles built up the main portion of OM within the Miocene, TOC-rich sediments. The most probable source of this oxidized OM are reworked sediments from the Scandinavian shelf. Changes in the input of these organic particles are to some degree correlative with sea-level changes. The Cenozoic accumulation of autochthonous OM is low and does not reveal a clear variation during the Miocene and early Pliocene. In spite of a high accumulation rate of biogenic opal during the Early Miocene, the accumulation rate of autochthonous TOC is low. The autochthonous particle assemblage is dominated by relatively inert OM, like dinoflagellate cysts. This points to an intensive biological and/or early diagenetic degradation of the marine OM under well oxidized bottom water conditions during the last 23 Myr. Nevertheless, a continuation of marine OM degradation during later stages of diagenesis cannot be excluded. A prominent dominance of allochthonous OM over autochthonous is documented with the beginning of the Pliocene. At 2.45 Ma the episodic occurrence of ice-rafted, thermally mature OM reflects the onset of the glacial erosion of Mesozoic, coal and black shale bearing sediments on the Scandinavian and Barents Sea shelves. The first occurrence of these, in view of the actual burial depth, thermally overmature OM particles is, therefore, a marker for the beginning of the strong Scandinavian glaciation and the advance of the glacial front toward the shelves.

Petrography and geochemistry of organic matter at DSDP Holes 80-549 and 80-550B

Three lower Barremian to middle/upper Cenomanian samples from DSDP Hole 549 and three lower Cenomanian to lower Maestrichtian samples from DSDP Hole 550B were investigated by organic geochemical and organic petrographic methods. The samples came from wells drilled in the area of the Goban Spur in the northeastern Atlantic; they represent gray to greenish gray carbonaceous mud or siltstones from the deeper parts of the Cretaceous sequences penetrated and light-colored chalks from the shallower ones. The total amount of organic carbon is below 1% in all samples; it is especially low in the Cenomanian to Maestrichtian chalks. Terrigenous organic matter predominates; only the Barremian sample shows a moderate number of marine phytoclasts. As indicated by several parameters, the maturity of the organic matter is low, corresponding to about 0.4% vitrinite reflectance.