Prediction of GC retention values under various column temperature conditions from temperature programmed data

A numerical approach has been developed for the correlation of retention limes (total retention lime) with temperature in gas chromatography, which allows the calculation of retention parameters including retention index from data acquired under two or more different temperature program conditions. By using this procedure the optimization of temperature condition can be further achieved, especially when a temperature-programmed run is the most suitable mode in the preliminary development of an analytical method for the analysis of an unknown sample.

Microcoulometric Determination Of Total Organo-Chlorinepesticide And Polychlorinated Biphenyl Residues In Grey Seal (Halichoerus-Grypus) Blubber

A procedure for estimating total organochlorine pesticide and PCB residue in seal blubber at concentrations of greater than 1μg g-1 of lipid is described. Lipid is cleaned up by alumina column chromatography, and the halogen concentration of the resulting hexane eluace is determined by combustion and microcoulometry. Results are similar to those obtained by gas chromatographic analysis and can be used to interpolate between results so obtained when data on specific organochlorine compounds is not required for each sample. The organochlorine residues recovered in this manner did not constitute all the halogen determined by combustion and microcoulometry of seal lipid. Analysis by the total halogen procedure was 2.5 tunes faster than the rate achieved with a combination of liquid and gas chromatography operated manually; the requirements for laboratory equipment and space for sample preparation are reduced.

Effect of pH, temperature, and moisture on the formation of volatile compounds in glycine/glucose model systems

Mixtures of glycine, glucose, and starch were extrusion cooked using sodium hydroxide at 0, 3, and 6 g/L of extruder water feed, 18% moisture, and 120, 150, and 180 degreesC target die temperatures, giving extrudates with pH values of 5.6, 6.8, and 7.4. Freeze-dried equimolar solutions of glucose and glycine were heated either dry or after equilibration to similar to 13% moisture at 180 degreesC in a reaction-tube system designed to mimic the heating profile in an extruder. Volatile compounds were isolated onto Tenax and analyzed by gas chromatography-mass spectrometry. For the extrudates, total yields of volatiles increased with decreasing pH at 180 degreesC, reached a maximum at pH 6.S at 150 degreesC, and increased with increasing pH at 120 degreesC. Amounts increased with temperature at all pH values. Pyrazines were the most abundant class for all sets of conditions (54-79% of total volatiles). Pyrroles, ketones, furans, oxazoles, and pyridines were also identified. Yields of volatiles from the reaction-tube samples increased by > 60% in the moist system. Levels of individual classes also increased in the presence of moisture, except pyrazines, which decreased similar to3.5-fold. Twenty-one of the compounds were common to the reaction-tube samples and the extrudates.

The effects of moisture, cation concentration, temperature, density and composition of soils on their electrical resistivity

The effects. of moisture, cation concentration, dens ity , temper~ t ure and grai n si ze on the electrical resistivity of so il s are examined using laboratory prepared soils. An i nexpen si ve method for preparing soils of different compositions was developed by mixing various size fractions i n the laboratory. Moisture and cation c oncentration are related to soil resistivity by powe r functions, whereas soil resistiv ity and temperature, density, Yo gravel, sand , sil t, and clay are related by exponential functions . A total of 1066 cases (8528 data) from all the experiments were used in a step-wise multiple linear r egression to determine the effect of each variable on soil resistivity. Six variables out of the eight variables studied account for 92.57/. of the total variance in so il resistivity with a correlation coefficient of 0.96. The other two variables (silt and gravel) did not increase the · variance. Moisture content was found to be - the most important Yo clay. variable- affecting s oil res istivi ty followed by These two variables account for 90.81Yo of the total variance in soil resistivity with a correlation ~oefficient ·.of 0 . 95. Based on these results an equation to ' ~~ed{ ct soil r esist ivi ty using moisture and Yo clay is developed . To t est the predicted equation, resistivity measurements were made on natural soils both in s i tu a nd i n the laboratory. The data show that field and laboratory measurements are comparable. The predicted regression line c losely coinciqes with resistivity data from area A and area B soils ~clayey and silty~clayey sands). Resistivity data and the predicted regression line in the case of c layey soils (clays> 40%) do not coincide, especially a t l ess than 15% moisture. The regression equation overestimates the resistivity of so i l s from area C and underestimates for area D soils. Laboratory prepared high clay soils give similar trends. The deviations are probably caused by heterogeneous distribution of mo i sture and difference in the type o f cl ays present in these soils.

Studies toward the total synthesis of natural and unnatural aeruginosins

Nous avons démontré l’utilité du groupement protecteur tert-butylsulfonyle (N-Bus) pour la chimie des acides aminés et des peptides. Celui-ci est préparé en deux étapes, impliquant la réaction d’une amine avec le chlorure de tert-butylsulfinyle, suivie par l’oxydation par du m-CPBA, pour obtenir les tert-butylsulfonamides correspondants avec d’excellents rendements. Le groupement N-Bus peut être clivé par traitement avec 0.1 N TfOH/DCM/anisole à 0oC en 10h pour régénérer le sel d’ammonium. Une variété d’acides aminés N-Bus protégés ainsi que d’autres aminoacides peuvent alors être utilisés pour préparer divers dipeptides et tripeptides. A l’exception du groupe N-Fmoc, les conditions de déprotection du groupe N-Bus clivent également les groupements N-Boc, N-Cbz et O-Bn. Une déprotection sélective et orthogonale des groupes N-Boc, N-Cbz, N-Fmoc et O-Bn est également possible en présence du groupe protecteur N-Bus. Le nouvel acide aminé non-naturel (3R, 2R) 3–méthyl-D-leucine (β-Me-Leu) et son régioisomère 2-méthyle ont été synthétisés par ouverture d’une N-Ts aziridine en présence d’un excès de LiMe2Cu. Chacun des régioisomères du mélange (1:1,2) a été converti en la méthylleucine correspondante, puis couplé à l’acide D-phényllactique puis au motif 2-carboxyperhydroindole 4-amidinobenzamide en présence de DEPBT. Des élaborations ultérieures ont conduit à des analogues peptidiques non-naturels d’aeruginosines telles que la chlorodysinosine A. Les deux analogues ont ensuite été évalués pour leur activité inhibitrice de la thrombine et la trypsine. La présumée aeruginosine 3-sulfate 205B et son anomère β ont été synthétisés avec succès à partir de 5 sous-unités : la 3-chloroleucine, l’acide D-phényllactique, le D-xylose, le 2-carboxy-6-hydroxyoctahydroindole et l’agmatine. La comparaison des données RMN 1H et 13C reportées avec celles obtenues avec l’aeruginosine synthétique 205B révèle une différence majeure pour la position du groupe présumé 3'-sulfate sur l’unité D-xylopyranosyle. Nous avons alors synthétisés les dérivés méthyl-α-D-xylopyranosides avec un groupement sulfate à chacune des positions hydroxyles, afin de démontrer sans ambiguïté la présence du sulfate en position C-4' par comparaison des données spectroscopiques RMN 1H et 13C. La structure de l’aeruginosine 205B a alors été révisée. Une des étapes-clés de cette synthèse consiste en la formation du glycoside avec le groupe hydroxyle en C-6 orienté en axial sur la sous-unité Choi. Le 2-thiopyridylcarbonate s’est avéré une méthode efficace pour l’activation anomérique. Le traitement par AgOTf et la tétraméthylurée en solution dans un mélange éther-DCM permet d’obtenir l’anomère α désiré, qui peut alors être aisément séparé de l’anomère β par chromatographie

Intraseasonal oscillation of total precipitable water over North Indian Ocean and its application in the diagnostic study of coastal rainfall

TRMM Microwave Imager (TMI) is reported to be a useful sensor to measure the atmospheric and oceanic parameters even in cloudy conditions. Vertically integrated specific humidity, Total Precipitable Water (TPW) retrieved from the water vapour absorption channel (22GHz.) along with 10m wind speed and rain rate derived from TMI is used to investigate the moisture variation over North Indian Ocean. Intraseasonal Oscillations (ISO) of TPW during the summer monsoon seasons 1998, 1999, and 2000 over North Indian Ocean is explored using wavelet analysis. The dominant waves in TPW during the monsoon periods and the differences in ISO over Arabian Sea and Bay of Bengal are investigated. The northward propagation of TPW anomaly and its coherence with the coastal rainfall is also studied. For the diagnostic study of heavy rainfall spells over the west coast, the intrusion of TPW over the North Arabian Sea is seen to be a useful tool.

Physico-chemical controls on phosphorus cycling in two lowland streams. Part 1 - the water column

This paper investigates phosphorus (P) transport and transformation dynamics in two contrasting sub-catchments of the River Kennel, England. Samples were collected daily under baseflow and hourly under stormflow conditions using autosamplers for 2 years and analysed for a range of determinands (full P fractionation, suspended sediment (SS), cations, pH, alkalinity, temperature and oxygen). Concentrations of SRP, SUP, PP and SS were higher in the flashy River Enborne (means of 0.186, 0.071, 0.101 and 34 mg l(-1), respectively) than the groundwater-fed River Lambourn (0.079, 0.057, 0.028 and 9 mg l(-1), respectively). A seasonal trend in the daily P dataset was evident, with lower concentrations during intermediate flows and the spring (caused by a dilution effect and macrophyte uptake) than during baseflow conditions. However, in the hourly P dataset, highest concentrations were observed during storm events in the autumn and winter (reflecting higher scour with increased capacity to entrain particles). Storm events were more significant in contributing to the total P load in the River Enborne than the River Lambourn, especially during August to October, when dry antecedent conditions were observed in the catchment. Re-suspension of P-rich sediment that accumulated within the channel during summer low flows might account for these observations. It is suggested that a P-calcite co-precipitation mechanism was operating during summer in the River Lambourn, while adsorption by metal oxyhydroxide groups was an important mechanism controlling P fractionation in the River Enborne. The influence of flow conditions and channel storage/release mechanisms on P dynamics in these two lowland rivers is assessed. (C) 2004 Elsevier B.V. All rights reserved.

The diurnal course of soil moisture as measured by various dielectric sensors: Effects of soil temperature and the implications for evaporation estimates

Soil moisture content, theta, of a bare and vegetated UK gravelly sandy loam soil (in situ and repacked in small lysimeters) was measured using various dielectric instruments (single-sensor ThetaProbes, multi-sensor Profile Probes, and Aquaflex Sensors), at depths ranging between 0.03 and I m, during the summers of 2001 (in situ soil) and 2002 (mini-lysimeters). Half-hourly values of evaporation, E, were calculated from diurnal changes in total soil profile water content, using the soil water balance equation. For the bare soil field, Profile Probes and ML2x ThetaProbes indicated a diurnal course of theta that did not concur with typical soil physical observations: surface layer soil moisture content increased from early morning until about midday, after which theta declined, generally until the early evening. The unexpected course of theta was positively correlated to soil temperature, T-s, also at deeper depths. Aquaflex and ML1 ThetaProbe (older models) outputs, however, reflected common observations: 0 increased slightly during the night (capillary rise) and decreased from the morning until late afternoon (as a result of evaporation). For the vegetated plot, the spurious diurnal theta fluctuations were less obvious, because canopy shading resulted in lower amplitudes of T-s. The unrealistic theta profiles measured for the bare and vegetated field sites caused diurnal estimates of E to attain downward daytime and upward night-time values. In the mini-lysimeters, at medium to high moisture contents, theta values measured by (ML2x) ThetaProbes followed a relatively realistic course, and predictions of E from diurnal changes in vertically integrated theta generally compared well with lysimeter estimates of E. However, time courses of theta and E became comparable to those observed for the field plots when the soil in the lysimeters reached relatively low values of theta. Attempts to correct measured theta for fluctuations in T, revealed that no generally applicable formula could be derived. (c) 2005 Elsevier B.V. All rights reserved.

Quantitative response of the longevity of seed of twelve crops to temperature and moisture in hermetic storage

Seeds of 39 seed lots of a total of twelve different crops were stored hermetically in a wide range of air-dry environments (2-25% moisture content at 0-50 degrees C), viability assessed periodically, and the seed viability equation constants estimated. Within a species, estimates of the constants which quantify absolute longevity (K-E) and the relative effects on longevity of moisture content (C-W) and temperature (C-H and C-Q) did not differ (P >0.05 to P >0.25) among lots. Comparison among the 12 crops provided variant estimates of K-E and C-W (P< 0.01), but common values of C-H and C-Q (0.0322 and 0.000454, respectively, P >0.25). Maize (Zea mays) provided the greatest estimate of K-E (9.993, s.e.= 0.456), followed by sorghum (Sorghum bicolor) (9.381, s.e. 0.428), pearl millet (Pennisetum typhoides) (9.336, s.e.= 0.408), sugar beet (Beta vulgaris) (8.988, s.e.= 0.387), African rice (Oryza glaberrima) (8.786, s.e.= 0.484), wheat (Triticum aestivum) (8.498, s.e.= 0.431), foxtail millet (Setaria italica) (8.478, s.e.= 0.396), sugarcane (Saccharum sp.) (8.454, s.e.= 0.545), finger millet (Eleusine coracana) (8.288, s.e.= 0.392), kodo millet (Paspalum scrobiculatum) (8.138, s.e.= 0.418), rice (Oryza sativa) (8.096, s.e.= 0.416) and potato (Solanum tuberosum) (8.037, s.e.= 0.397). Similarly, estimates of C-W were ranked maize (5.993, s.e.= 0.392), pearl millet (5.540, s.e.= 0.348), sorghum (5.379, s.e.=0.365), potato (5.152, s.e.= 0.347), sugar beet (4.969, s.e.= 0.328), sugar cane (4.964, s.e.= 0.518), foxtail millet (4.829, s.e.= 0.339), wheat (4.836, s.e.= 0.366), African rice (4.727, s.e.= 0.416), kodo millet (4.435, s.e.= 0.360), finger millet (4.345, s.e.= 0.336) and rice (4.246, s.e.= 0.355). The application of these constants to long-term seed storage is discussed.

Near infrared reflectance spectroscopy (NIRS) to predict biological parameters of maize silage: effects of particle comminution, oven drying temperature and the presence of residual moisture

Maize silage nutritive quality is routinely determined by near infrared reflectance spectroscopy (NIRS). However, little is known about the impact of sample preparation on the accuracy of the calibration to predict biological traits. A sample population of 48 maize silages representing a wide range of physiological maturities was used in a study to determine the impact of different sample preparation procedures (i.e., drying regimes; the presence or absence of residual moisture; the degree of particle comminution) on resultant NIR prediction statistics. All silages were scanned using a total of 12 combinations of sample pre-treatments. Each sample preparation combination was subjected to three multivariate regression techniques to give a total of 36 predictions per biological trait. Increased sample preparations procedure, relative to scanning the unprocessed whole plant (WP) material, always resulted in a numerical minimisation of model statistics. However, the ability of each of the treatments to significantly minimise the model statistics differed. Particle comminution was the most important factor, oven-drying regime was intermediate, and residual moisture presence was the least important. Models to predict various biological parameters of maize silage will be improved if material is subjected to a high degree of particle comminution (i.e., having been passed through a 1 mm screen) and developed on plant material previously dried at 60 degrees C. The extra effort in terms of time and cost required to remove sample residual moisture cannot be justified. (c) 2005 Elsevier B.V. All rights reserved.

The importance of temperature and moisture to the egg-laying behaviour of a pest slug, Deroceras reticulatum

Oviposition behaviour is important when modelling the population dynamics of many invertebrates. The numbers of eggs laid are frequently used to describe fecundity, but this measure may differ significantly from realised fecundity. Oviposition has been shown to be important when describing the dynamics of slug populations, which are important agricultural pests. The numbers of eggs laid by Deroceras reticulatum and their viability were measured across a range of 16 temperature (4, 10, 15 and 23 degrees C) by moisture (33%, 42%, 53% and 58% by dry soil weight) experimental combinations. A fitted quadratic response surface model was used to estimate how D. reticulatum adjusted its egg laying to the surrounding temperature and moisture conditions, with most eggs being laid at a combination of 53% soil moisture and 18 degrees C. The number and proportion of viable eggs also covaried with temperature and moisture, suggesting that D. reticulatum may alter their investment in reproduction to maximise their fitness. We have shown that the number of viable eggs differs from the total number of eggs laid by D. reticulatum. Changes in egg viability with temperature and moisture may also be seen in other species and should be considered when modelling populations of egg-laying invertebrates.

A simple column model to explore anticipated problems in variational assimilation of satellite observations

We investigate a simplified form of variational data assimilation in a fully nonlinear framework with the aim of extracting dynamical development information from a sequence of observations over time. Information on the vertical wind profile, w(z ), and profiles of temperature, T (z , t), and total water content, qt (z , t), as functions of height, z , and time, t, are converted to brightness temperatures at a single horizontal location by defining a two-dimensional (vertical and time) variational assimilation testbed. The profiles of T and qt are updated using a vertical advection scheme. A basic cloud scheme is used to obtain the fractional cloud amount and, when combined with the temperature field, this information is converted into a brightness temperature, using a simple radiative transfer scheme. It is shown that our model exhibits realistic behaviour with regard to the prediction of cloud, but the effects of nonlinearity become non-negligible in the variational data assimilation algorithm. A careful analysis of the application of the data assimilation scheme to this nonlinear problem is presented, the salient difficulties are highlighted, and suggestions for further developments are discussed.

The effect of nonlinearity on the variational assimilation of satellite observations using a simple column model

Cloud imagery is not currently used in numerical weather prediction (NWP) to extract the type of dynamical information that experienced forecasters have extracted subjectively for many years. For example, rapidly developing mid-latitude cyclones have characteristic signatures in the cloud imagery that are most fully appreciated from a sequence of images rather than from a single image. The Met Office is currently developing a technique to extract dynamical development information from satellite imagery using their full incremental 4D-Var (four-dimensional variational data assimilation) system. We investigate a simplified form of this technique in a fully nonlinear framework. We convert information on the vertical wind field, w(z), and profiles of temperature, T(z, t), and total water content, qt (z, t), as functions of height, z, and time, t, to a single brightness temperature by defining a 2D (vertical and time) variational assimilation testbed. The profiles of w, T and qt are updated using a simple vertical advection scheme. We define a basic cloud scheme to obtain the fractional cloud amount and, when combined with the temperature field, we convert this information into a brightness temperature, having developed a simple radiative transfer scheme. With the exception of some matrix inversion routines, all our code is developed from scratch. Throughout the development process we test all aspects of our 2D assimilation system, and then run identical twin experiments to try and recover information on the vertical velocity, from a sequence of observations of brightness temperature. This thesis contains a comprehensive description of our nonlinear models and assimilation system, and the first experimental results.