Design, Technology and Characterization of Micromechanised Sensors and Actuators for Harsh Environments

Los sistemas micro electro mecánicos (MEMS) han demostrado ser una exitosa familia de dispositivos que pueden usarse como plataforma para el desarrollo de dispositivos con aplicaciones en óptica, comunicaciones, procesado de señal y sensorización. Los dispositivos MEMS estándar suelen estar fabricados usando tecnología de silicio. Sin embargo, el rendimiento de estos MEMS se puede mejorar si se usan otros materiales. Por ejemplo, el diamante nanocristalino (NCD) ofrece unas excelentes propiedades mecánicas, transparencia y una superficie fácil de funcionalizar. Por otro lado, el sistema de materiales (In; Ga; Al)N, los materiales IIIN, se pueden usar para producir estructuras monocristalinas con alta sensibilidad mecánica y química. Además, el AlN se puede depositar por pulverización catódica reactiva sobre varios substratos, incluyendo NCD, para formar capas policristalinas orientadas con alta respuesta piezoeléctrica. Adicionalmente, tanto el NCD como los materiales III-N muestran una gran estabilidad térmica y química, lo que los hace una elección idónea para desarrollar dispositivos para aplicaciones para alta temperatura, ambientes agresivos e incluso para aplicaciones biocompatibles. En esta tesis se han usado estos materiales para el diseño y medición de demostradores tecnológicos. Se han perseguido tres objetivos principales: _ Desarrollo de unos procesos de fabricación apropiados. _ Medición de las propiedades mecánicas de los materiales y de los factores que limitan el rendimiento de los dispositivos. _ Usar los datos medidos para desarrollar dispositivos demostradores complejos. En la primera parte de esta tesis se han estudiado varias técnicas de fabricación. La estabilidad de estos materiales impide el ataque y dificulta la producción de estructuras suspendidas. Los primeros capítulos de esta disertación se dedican al desarrollo de unos procesos de transferencia de patrones por ataque seco y a la optimización del ataque húmedo sacrificial de varios substratos propuestos. Los resultados de los procedimientos de ataque se presentan y se describe la optimización de las técnicas para la fabricación de estructuras suspendidas de NCD y materiales III-N. En un capítulo posterior se estudia el crecimiento de AlN por pulverización catódica. Como se ha calculado en esta disertación para obtener una actuación eficiente de MEMS, las capas de AlN han de ser finas, típicamente d < 200 nm, lo que supone serias dificultades para la obtención de capas orientadas con respuesta piezoeléctrica. Las condiciones de depósito se han mapeado para identificar las fronteras que proporcionan el crecimiento de material orientado desde los primeros pasos del proceso. Además, durante la optimización de los procesos de ataque se estudió un procedimiento para fabricar películas de GaN nanoporoso. Estas capas porosas pueden servir como capas sacrificiales para la fabricación de estructuras suspendidas de GaN con baja tensión residual o como capas para mejorar la funcionalización superficial de sensores químicos o biológicos. El proceso de inducción de poros se discutirá y también se presentarán experimentos de ataque y funcionalización. En segundo lugar, se han determinado las propiedades mecánicas del NCD y de los materiales III-N. Se han fabricado varias estructuras suspendidas para la medición del módulo de Young y de la tensión residual. Además, las estructuras de NCD se midieron en resonancia para calcular el rendimiento de los dispositivos en términos de frecuencia y factor de calidad. Se identificaron los factores intrínsecos y extrínsecos que limitan ambas figuras de mérito y se han desarrollado modelos para considerar estas imperfecciones en las etapas de diseño de los dispositivos. Por otra parte, los materiales III-N normalmente presentan grandes gradientes de deformación residual que causan la deformación de las estructuras al ser liberadas. Se han medido y modelado estos efectos para los tres materiales binarios del sistema para proporcionar puntos de interpolación que permitan predecir las características de las aleaciones del sistema III-N. Por último, los datos recabados se han usado para desarrollar modelos analíticos y numéricos para el diseño de varios dispositivos. Se han estudiado las propiedades de transducción y se proporcionan topologías optimizadas. En el último capítulo de esta disertación se presentan diseños optimizados de los siguientes dispositivos: _ Traviesas y voladizos de AlN=NCD con actuación piezoeléctrica aplicados a nanoconmutadores de RF para señales de alta potencia. _ Membranas circulares de AlN=NCD con actuación piezoeléctrica aplicadas a lentes sintonizables. _ Filtros ópticos Fabry-Pérot basados en cavidades aéreas y membranas de GaN actuadas electrostáticamente. En resumen, se han desarrollado unos nuevos procedimientos optimizados para la fabricación de estructuras de NCD y materiales III-N. Estas técnicas se han usado para producir estructuras que llevaron a la determinación de las principales propiedades mecánicas y de los parámetros de los dispositivos necesarios para el diseño de MEMS. Finalmente, los datos obtenidos se han usado para el diseño optimizado de varios dispositivos demostradores. ABSTRACT Micro Electro Mechanical Systems (MEMS) have proven to be a successful family of devices that can be used as a platform for the development of devices with applications in optics, communications, signal processing and sensorics. Standard MEMS devices are usually fabricated using silicon based materials. However, the performance of these MEMS can be improved if other material systems are used. For instance, nanocrystalline diamond (NCD) offers excellent mechanical properties, optical transparency and ease of surface functionalization. On the other hand, the (In; Ga; Al)N material system, the III-N materials, can be used to produce single crystal structures with high mechanical and chemical sensitivity. Also, AlN can be deposited by reactive sputtering on various substrates, including NCD, to form oriented polycrystalline layers with high piezoelectric response. In addition, both NCD and III-N materials exhibit high thermal and chemical stability, which makes these material the perfect choice for the development of devices for high temperatures, harsh environments and even biocompatible applications. In this thesis these materials have been used for the design and measurement of technological demonstrators. Three main objectives have been pursued: _ Development of suitable fabrication processes. _ Measurement of the material mechanical properties and device performance limiting factors. _ Use the gathered data to design complex demonstrator devices. In a first part of the thesis several fabrication processes have been addressed. The stability of these materials hinders the etching of the layers and hampers the production of free standing structures. The first chapters of this dissertation are devoted to the development of a dry patterning etching process and to sacrificial etching optimization of several proposed substrates. The results of the etching processes are presented and the optimization of the technique for the manufacturing of NCD and III-N free standing structures is described. In a later chapter, sputtering growth of thin AlN layers is studied. As calculated in this dissertation, for efficient MEMS piezoelectric actuation the AlN layers have to be very thin, typically d < 200 nm, which poses serious difficulties to the production of c-axis oriented material with piezoelectric response. The deposition conditions have been mapped in order to identify the boundaries that give rise to the growth of c-axis oriented material from the first deposition stages. Additionally, during the etching optimization a procedure for fabricating nanoporous GaN layers was also studied. Such porous layers can serve as a sacrificial layer for the release of low stressed GaN devices or as a functionalization enhancement layer for chemical and biological sensors. The pore induction process will be discussed and etching and functionalization trials are presented. Secondly, the mechanical properties of NCD and III-N materials have been determined. Several free standing structures were fabricated for the measurement of the material Young’s modulus and residual stress. In addition, NCD structures were measured under resonance in order to calculate the device performance in terms of frequency and quality factor. Intrinsic and extrinsic limiting factors for both figures were identified and models have been developed in order to take into account these imperfections in the device design stages. On the other hand, III-N materials usually present large strain gradients that lead to device deformation after release. These effects have been measured and modeled for the three binary materials of the system in order to provide the interpolation points for predicting the behavior of the III-N alloys. Finally, the gathered data has been used for developing analytic and numeric models for the design of various devices. The transduction properties are studied and optimized topologies are provided. Optimized design of the following devices is presented at the last chapter of this dissertation: _ AlN=NCD piezoelectrically actuated beams applied to RF nanoswitches for large power signals. _ AlN=NCD piezoelectrically actuated circular membranes applied to tunable lenses. _ GaN based air gap tunable optical Fabry-Pérot filters with electrostatic actuation. On the whole, new optimized fabrication processes has been developed for the fabrication of NCD and III-N MEMS structures. These processing techniques was used to produce structures that led to the determination of the main mechanical properties and device parameters needed for MEMS design. Lastly, the gathered data was used for the design of various optimized demonstrator devices.

Cyclically-arranged, storm-controlled, prograding lithosomes in Messinian terrigenous shelves (Bajo Segura Basin, western Mediterranean)

This work focuses on a Messinian shallow-marine terrigenous unit, termed the La Virgen Formation, which forms part of the sedimentary infill of the Bajo Segura Basin (Betic margin of the western Mediterranean). This formation was deposited during a high sea level phase prior to the onset of the Messinian Salinity Crisis. Stratigraphically, it comprises a prograding stack of sandstone lithosomes alternating with marly intervals (1st-order cyclicity). These lithosomes are characterized by a homoclinal geometry that tapers distally, and interfinger with pelagic sediments rich in planktonic and benthic microfauna (Torremendo Formation). An analysis of sedimentary facies of each lithosome reveals a repetitive succession of sandy storm beds (tempestites), occasionally amalgamated, which are separated by thin marly layers (2nd-order cyclicity). Each storm bed contains internal erosional surfaces (3rd-order cyclicity) that delimit sets of laminae. Two categories of storm beds have been differentiated. The first one includes layers formed below storm wave base (SWB), characterized by traction structures associated to unidirectional flows (scoured base, planar lamination, and parting lineation). The second category consists of layers deposited above the SWB which display typical high regime oscillatory flow structures (swaley and hummocky cross lamination). In both cases, the ichnological record is characterized by an oligotypic association of Ophiomorpha nodosa, which can be interpreted as the result of allochthonous tracemakers (crustaceans) transported during storm events together with the sediment. The benthic microfauna in the marly intervals that separate the sandstone lithosomes (1st-order cyclicity) indicates that the storm ebb surges were deposited at depths ranging from those of inner shelf settings (with Elphidium spp. and Cibicides lobatulus) to those of outer shelf (with Valvulineria complanata and Uvigerina cylindrica). At the distal end of the sandstone lithosomes, the planktonic microfauna is characterized by a high content of taxa indicative of warm-oligotrophic waters (Globigerinoides obliquus and Globigerinoides bulloideus). In contrast, in the marly intervals, the microfauna is dominated by species typical of cold-eutrophic waters (Globigerina and Neogloboquadrina). This alternation of planktic foraminiferal assemblages is interpreted as being the expression of climatic cycles, in which every episode of progradation of tempestite-dominated lithosomes corresponds to maximum insolation and warm waters, whereas episodes of marly deposition correspond to minimal insolation and cold waters. The 1st-order cyclicity recorded in the La Virgen Formation, in a context of terrigenous storm-dominated shelf, corresponds to sapropel/homogeneous marl cycles formed in a pelagic basin (Torremendo Fm). These cycles in pelagic sediments are commonplace throughout the Mediterranean during the Messinian and reflect precession orbital changes: repeated periods of maximum insolation – minimum precession (sapropels) and minimal insolation – maximum precession (homogeneous marls). The fact that the example of terrigenous unit studied herein is coetaneous with the well-developed reef complexes in the Mediterranean basins points out the importance of sediment supply in the formation of large-scale sandy lithosomes. This is a crucial aspect to understanding reservoir genesis as well as lateral stratigraphic relationships with potential seal and/or source rocks.

(Table 2) Methane to ethane ratio, and d13C-methane at DSDP Hole 76-533

Natural gas hydrates are clathrates in which water molecules form a crystalline framework that includes and is stabilized by natural gas (mainly methane) at appropriate conditions of high pressures and low temperatures. The conditions for the formation of gas hydrates are met within continental margin sediments below water depths greater than about 500 m where the supply of methane is sufficient to stabilize the gas hydrate. Observations on DSDP Leg 11 suggested the presence of gas hydrates in sediments of the Blake Outer Ridge. Leg 76 coring and sampling confirms that, indeed, gas hydrates are present there. Geochemical evidence for gas hydrates in sediment of the Blake Outer Ridge includes (1) high concentrations of methane, (2) a sediment sample with thin, matlike layers of white crystals that released a volume of gas twenty times greater than its volume of pore fluid, (3) a molecular distribution of hydrocarbon gases that excluded hydrocarbons larger than isobutane, (4) results from pressure core barrel experiments, and (5) pore-fluid chemistry. The molecular composition of the hydrocarbons in these gas hydrates and the isotopic composition of the methane indicate that the gas is derived mainly from microbiological processes operating on the organic matter within the sediment. Although gas hydrates apparently are widespread on the Blake Outer Ridge, they probably are not of great economic significance as a potential, unconventional, energy resource or as an impermeable cap for trapping upwardly migrating gas at Site 533.

The Quaternary pyroclastic succession of southeast Tenerife, Canary Islands: Explosive eruptions, related caldera subsidence, and sector collapse

A much-revised Quaternary stratigraphy is presented for ignimbrites and pumice fall deposits of the Bandas del Sur, in southern Tenerife. New Ar-41/Ar-39 data obtained for the Arico, Granadilla, Fasnia, Poris, La Caleta and Abrigo formations are presented, allowing correlation with previously dated offshore marine ashfall layers and volcaniclastic sediments. We also provide a minimum age of 287 +/- 7 ka for a major sector collapse event at the Gaimar valley. The Bandas del Sur succession includes more than seven widespread ignimbrite sheets that have similar characteristics, including widespread basal Plinian layers, predominantly phonolite composition, ignimbrites with similar extensive geographic distributions, thin condensed veneers with abundant diffuse bedding and complex lateral and vertical grading patterns, lateral gradations into localized massive facies within palaeo-wadis, and widespread lithic breccia layers that probably record caldera-forming eruptions. Each ignimbrite sheet records substantial bypassing of pyroclastic material into the ocean. The succession indicates that Las Canadas volcano underwent a series of major explosive eruptions, each starting with a Plinian phase followed by emplacement of ignimbrites and thin ash layers, some of coignimbrite origin. Several of the ignimbrite sheets are compositionally zoned and contain subordinate mafic pumices and banded pumices indicative of magma mingling immediately prior to eruption. Because passage of each pyroclastic density current was characterized by phases of non-deposition and erosion, the entire course of each eruption is incompletely recorded at any one location, accounting for some previously perceived differences between the units. Because each current passed into the ocean, estimating eruption volumes is virtually impossible. Nevertheless, the consistent widespread distributions and the presence of lithic breccias within most of the ignimbrite sheets suggest that at least seven caldera collapse eruptions are recorded in the Bandas del Sur succession and probably formed a complex, nested collapse structure. Detailed field relationships show that extensive ignimbrite sheets (e.g. the Arico, Poris and La Caleta formations) relate to previously unrecognized caldera collapse events. We envisage that the evolution of the nested Las Cahadas caldera is more complex than previously thought and involved a protracted history of successive ignimbrite-related caldera collapse events, and large sector collapse events, interspersed with edifice-building phases.

Autocatalytic deposition of composite coatings

The deposition and properties of electroless nickel composite coatings containing graphite, PTFE and chromium were investigated. Solutions were developed for the codeposition of graphite and chromium with electroless nickel. Solutions for the deposition of graphite contained heavy metal ions for stability, with non-ionic and anionic surfactants to provide wetting and dispersion of the particles. Stability for the codeposition of chromium particles was achieved by oxidation of the chromium. Thin oxide layers of 200 nm thick prevented initiation of the electroless reaction onto the chromium. A mechanism for the formation of electroless composite coatings was considered based on the physical adsorption of particles and as a function of the adsorption of charged surfactants and metal cations from solution. The influence of variables such as particle concentration in solution, particle size, temperature, pH, and agitation on the volume percentage of particles codeposited was studied. The volume percentage of graphite codeposited was found to increase with concentration in solution and playing rate. An increase in particle size and agitation reduced the volume percentage codeposited. The hardness of nickel-graphite deposits was found to decrease with graphite content in the as-deposited and heat treated condition. The frictional and wear properties of electroless nickel-graphite were studied and compared to those of electroless nickel-PTFE. The self-lubricating nature of both coatings was found to be dependent on the ratio of coated area to uncoated area, the size and content of lubricating material in the deposit, and the load between contacting surfaces. The mechanism of self-lubrication was considered, concluding that graphite only produced an initial lubricating surface due to the orientation of flakes, unlike PTFE, which produced true self-lubrication throughout the coating life. Heat treatment of electroless nickel chromium deposits at 850oC for 8 and 16 hours produced nickel-iron-chromium alloy deposits with a phosphorus rich surface of high hardness. Coefficients of friction and wear rates were intially moderate for the phosphorus rich layer but increased for the nickel-iron-chromium region of the coating.

Petrologia das fraturas associadas a feições típicas de dissolução hipogênica na Formação Salitre, Bacia de Irecê, Bahia, Brasil

The recognition of karst reservoirs in carbonate rocks has become increasingly common. However, most karst features are small to be recognized in seismic sections or larger than expected to be investigated with borehole data. One way forward has been the study of analogue outcrops and caves. The present study investigates lithofacies and karst processes, which lead to the generation of the largest system of caves in South America. The study area is located in the Neoproterozoic Una Group in central-eastern Brazil. This province comprises several systems of carbonate caves (Karmann and Sanchéz, 1979), which include the Toca da Boa Vista and Barriguda caves, considered the largest caves in South America (Auler and Smart, 2003). These caves were formed mainly in dolomites of the Salitre Formation, which was deposited in a shallow marine environment in an epicontinental sea (Medeiros and Pereira, 1994). The Salitre Formation in the cave area comprises laminated mud/wakestones, intraclastic grainstones, oncolitic grainstones, oolitic grainstones, microbial laminites, colunar stromatolites, trombolites and fine siliciclastic rocks (marls, shales, and siltites). A thin layer and chert nodules also occur at the top of the carbonate unit. Phosphate deposits are also found. Our preliminary data indicate that folds and associated joints control the main karstification event at the end of the Brasiliano orogeny (740-540 Ma). We recognized five lithofacies in the cave system: (1) Bottom layers of grainstone with cross bedding comprise the main unit affected by speleogenesis, (2) thin grainstone layers with thin siltite layers, (3) microbial laminites layers, (4) layers of columnar stromatolites, and a (5) top layer of siltite. Levels (1) to (3) are affected by intense fracturing, whereas levels (4) and (5) seal the caves and have little fracturing. Chert, calcite and gipsite veins cut across the carbonate units and play a major role in diagenesis. Our preliminary study indicate that hypogenic spelogenesis is the main process of karst development and contributed significantly to the generation of secondary porosity and permeability in the carbonate units.

Sedimenttexturen und Lebensspuren der Sohlbank des Naturdenkmals „Saurierfährten Münchehagen“

The basal bed of the Natural Monument Münchehagen, called "Sohlbank", is composed of a quartzitic sandstone. The bed is characterized by wave ripple bedding, which is altered by biotrubation. Ist surface cuts erosively older, thin sandstone layers typically covered by riplle marks on their upper bedding plane. All ripple marks are oscillation ripples which are partially modified by retreating water. Sedimentary channel fillings cut into the “Sohlbank“. A highly diverse ichnofauna is described. It comprises elements of a Cruziana ichnocenosis in addition to some traces of a Skolithos ichnocenosis. The sedimentary and biogenic structures suggest a low energy, shallow-water depositional environment.

Large Rayleigh number thermal convection: heat flux predictions and strongly nonlinear solutions

We investigate the structure of strongly nonlinear Rayleigh–Bénard convection cells in the asymptotic limit of large Rayleigh number and fixed, moderate Prandtl number. Unlike the flows analyzed in prior theoretical studies of infinite Prandtl number convection, our cellular solutions exhibit dynamically inviscid constant-vorticity cores. By solving an integral equation for the cell-edge temperature distribution, we are able to predict, as a function of cell aspect ratio, the value of the core vorticity, details of the flow within the thin boundary layers and rising/falling plumes adjacent to the edges of the convection cell, and, in particular, the bulk heat flux through the layer. The results of our asymptotic analysis are corroborated using full pseudospectral numerical simulations and confirm that the heat flux is maximized for convection cells that are roughly square in cross section.

Nano-Engineering of Densely Packed Electrochemical Energy Storage Architectures by Atomic Layer Deposition

Nanostructures are highly attractive for future electrical energy storage devices because they enable large surface area and short ion transport time through thin electrode layers for high power devices. Significant enhancement in power density of batteries has been achieved by nano-engineered structures, particularly anode and cathode nanostructures spatially separated far apart by a porous membrane and/or a defined electrolyte region. A self-aligned nanostructured battery fully confined within a single nanopore presents a powerful platform to determine the rate performance and cyclability limits of nanostructured storage devices. Atomic layer deposition (ALD) has enabled us to create and evaluate such structures, comprised of nanotubular electrodes and electrolyte confined within anodic aluminum oxide (AAO) nanopores. The V2O5- V2O5 symmetric nanopore battery displays exceptional power-energy performance and cyclability when tested as a massively parallel device (~2billion/cm2), each with ~1m3 volume (~1fL). Cycled between 0.2V and 1.8V, this full cell has capacity retention of 95% at 5C rate and 46% at 150C, with more than 1000 charge/discharge cycles. These results demonstrate the promise of ultrasmall, self-aligned/regular, densely packed nanobattery structures as a testbed to study ionics and electrodics at the nanoscale with various geometrical modifications and as a building block for high performance energy storage systems[1, 2]. Further increase of full cell output potential is also demonstrated in asymmetric full cell configurations with various low voltage anode materials. The asymmetric full cell nanopore batteries, comprised of V2O5 as cathode and prelithiated SnO2 or anatase phase TiO2 as anode, with integrated nanotubular metal current collectors underneath each nanotubular storage electrode, also enabled by ALD. By controlling the amount of lithium ion prelithiated into SnO2 anode, we can tune full cell output voltage in the range of 0.3V and 3V. This asymmetric nanopore battery array displays exceptional rate performance and cyclability. When cycled between 1V and 3V, it has capacity retention of approximately 73% at 200C rate compared to 1C, with only 2% capacity loss after more than 500 charge/discharge cycles. With increased full cell output potential, the asymmetric V2O5-SnO2 nanopore battery shows significantly improved energy and power density. This configuration presents a more realistic test - through its asymmetric (vs symmetric) configuration – of performance and cyclability in nanoconfined environment. This dissertation covers (1) Ultra small electrochemical storage platform design and fabrication, (2) Electron and ion transport in nanostructured electrodes inside a half cell configuration, (3) Ion transport between anode and cathode in confined nanochannels in symmetric full cells, (4) Scale up energy and power density with geometry optimization and low voltage anode materials in asymmetric full cell configurations. As a supplement, selective growth of ALD to improve graphene conductance will also be discussed[3]. References: 1. Liu, C., et al., (Invited) A Rational Design for Batteries at Nanoscale by Atomic Layer Deposition. ECS Transactions, 2015. 69(7): p. 23-30. 2. Liu, C.Y., et al., An all-in-one nanopore battery array. Nature Nanotechnology, 2014. 9(12): p. 1031-1039. 3. Liu, C., et al., Improving Graphene Conductivity through Selective Atomic Layer Deposition. ECS Transactions, 2015. 69(7): p. 133-138.

Dynamic mechanical-thermal, microstructural and mechanical analysis of ultra-light polymer-metal composites: influence of forming

A really particular and innovative metal-polymer sandwich material is Hybrix. Hybrix is a product developed and manufactured by Lamera AB, Gothenburg, Sweden. This innovative hybrid material is composed by two relatively thin metal layers if compared to the core thickness. The most used metals are aluminum and stainless steel and are separated by a core of nylon fibres oriented perpendicularly to the metal plates. The core is then completed by adhesive layers applied at the PA66-metal interface that once cured maintain the nylon fibres in position. This special material is very light and formable. Moreover Hybrix, depending on the specific metal which is used, can achieve a good corrosion resistance and it can be cut and punched easily. Hybrix architecture itself provides extremely good bending stiffness, damping properties, insulation capability, etc., which again, of course, change in magnitude depending in the metal alloy which is used, its thickness and core thickness. For these reasons nowadays it shows potential for all the applications which have the above mentioned characteristic as a requirement. Finally Hybrix can be processed with tools used in regular metal sheet industry and can be handled as solid metal sheets. In this master thesis project, pre-formed parts of Hybrix were studied and characterized. Previous work on Hybrix was focused on analyze its market potential and different adhesive to be used in the core. All the tests were carried out on flat unformed specimens. However, in order to have a complete description of this material also the effect of the forming process must be taken into account. Thus the main activities of the present master thesis are the following: Dynamic Mechanical-Thermal Analysis (DMTA) on unformed Hybrix samples of different thickness and on pre-strained Hybrix samples, pure epoxy adhesive samples analysis and finally moisture effects evaluation on Hybrix composite structure.

Francisco Pizarro' s banner of arms: an analytical work contributing to latin America's history

The study of textiles is an open area of scientific research, which for its variety of material components and physical chemical diversity of conditions, makes a field of interest for scientific studies in the cultural heritage field. Archaeological/historical textiles offer the possibility to carry out studies on organic materials such as fibers, adhesion elements, dyes, paper, etc., as well as on inorganic compounds for instance metals, alloys, precious stones and other added ornamentation. That variety of composition, allow to use a combination of analytical techniques to solve the questions coming from the object in an archaeometric research. One kind of textile object that provides a valuable cultural information because of its linguistic representation employed by its carrier societies, are the flags/banners/emblems, objects made with a nonverbal communication purpose. As long as depending on the use and/or purpose of each object, varies both the materials/techniques used in its production and its iconography (style, color, emblem, shape), its study gives the possibility to extract information through their materials and manufacturing techniques about a temporal-spatial frame, a particular event or a specific character. The flags/banners have been used since the eleventh century as representative objects of power, hierarchy, social or military organization, or as communicative media. The use of these objects has been spread throughout the world, possibly due to its easy interpretation and/or appropriation by different societies, making it part of their own culture. The flags as symbols of territorial control, using emblems that represent a family, order or army, were introduced to the New World (America) with the arrival of the European conquerors at the end of the fifteenth century. Flags/banners representing the Royal dominion over conquered territories, the Catholic Church and conquistadors’ armies were the first to arrive. One of those flags that have endured over time, that have an invaluable cultural meaning for both American and Iberian societies, is the so-called Francisco Pizarro’s Banner of Arms. It is a textile object with metal threads decoration over a Royal emblem. According to historical sources, this object was used by Francisco Pizarro in 1532 on the conquest process of Peru, after received the permission by King Charles V to on behalf of him, to conquer the lands of the New World today known as Peru. After Pizarro’s control of the Inca territory, it is believed that Pizarro left his banner on top of the Inca’s Sun’s Temple as symbol of his rule. Centuries later, in the America libertarian campaigns, General Sucre, military at charge of the independence army in Peru, reports have found what he considered the Pizarro’s Banner, sending it to Bogotá as a symbol of victory, being kept since that time until today by the National Museum of Colombia. Due to historical discrepancies in the different movements of the so-called Pizarro’s Banner of Arms, its real meaning has been under discussion and because of the passage of time its physical condition has suffer deterioration. That is because its scientific study is now an interesting case study to respond to both historical and conservation questions of it. Through a collaboration with the National Museum of Colombia, a set of 25 samples of so-called Pizarro’s Banner of Arms were collected, covering the various components and areas from the object of study. These samples were subjected to analytical studies for physical and chemical characterization. Microscopic observation, VSEM-EDS analysis, Raman spectroscopy, chromatographic analysis (HPLC-MS, GCMS) and radiocarbon dating were done. Similarly, was sought through a direct in situ physical inspection to the object and through a research into historical sources, adequate information to solve the object’s problems. Results obtained allowed to identify as silk the textile used in the elaboration of the Banner’s fabric, as well as the use of natural dyes for dyeing the fibers used on the emblem: use of cochineal and brazil wood as a source of red, luteolin plant-based for yellow color, indigotine plant-based for blue, and a mixture of yellow and blue dyes for green were identified. Similarly, the use of animal glue in the manufacturing process and the use of rag paper was evident. The metal threads study from the Banner give a confirmation to a silver core wire gilded with a thin gold sheet, being flattened and entwined with silk threads for their use. Finally, using the radiocarbon results, it was possible to postulate with huge accuracy that the Banner date manufacture was between the XV-XVI century and subject to restoration processes with addition of textiles in modern times. Together with, was evident that the state of degradation of the fabric is due to natural degradation in the silk fibers, having that its color has faded and its mechanical properties decreased, leading to loss of rigidity and disappearance of the physical structure. Similarly, it was clear the original colors of the emblem and highlight problems of detachment of paper due to crystallization of the adhesive. In the same way, was found that the metal threads suffer corrosion by sulfur and detachment of its crystals. Finally, combining the analytical results and the historical sources data found from the so-called Francisco Pizarro’s Banner of Arms, allows to postulate that its manufacture process was done in Europe employing precious materials to obtain a long-life object with a deep message for its viewers. Also, the data obtained helps to support the possible idea that the object was employed by Francisco Pizarro in the Peru conquest process. However, by the symbols present in the object, its elaboration date and materials, this object its clearly unique in its kind, and the most important, by its linguistic message, does not represent to Francisco Pizarro or his army, meanwhile, represents the Spanish crown. Therefore, instead to be labeled as Francisco Pizarro’s Banner of Arms, it should be called the Colonial Royal Banner of Charles V in the New World; RESUMEN: El estudio de textiles es un área abierta de investigación científica, la cual por su variedad de componentes materiales y la diversidad de condiciones físico-químicas presentes en estos objetos, lo hace un campo de interés para estudios científicos en el patrimonio cultural. Los textiles arqueológicos/históricos brindan la posibilidad de realizar estudios en materiales orgánicos como fibras, elementos de adhesión, tinturas, papel, etc., e inorgánicos como metales, aleaciones, piedras preciosas y demás materiales decorativos añadidos. Por su variedad de composición, es posible emplear diversas técnicas analíticas para resolver aquellas preguntas propias del objeto en una investigación arqueométrica. Uno de los objetos textiles que brinda gran información cultural debido a su representación lingüística empleada por las sociedades portadoras, son las banderas/estandartes/emblemas. Donde varía dependiendo de su uso y/o propósito, los materiales empleados en su elaboración, al igual que su iconografía (estilo, color, emblema, forma). El estudio de estos objetos construidos con un propósito de comunicación no verbal, da la posibilidad de extraer información a través de sus materiales y técnicas de elaboración sobre un rango temporal-espacial, un evento determinado en la historia o incluso a un personaje en específico. Las banderas han sido empleadas desde el siglo XI como objetos representativos de poder, jerarquía, organización social o militar, o como medio de comunicación. El uso de estos objetos se ha extendido a lo largo del mundo posiblemente debido a su fácil interpretación y/o apropiación por distintas sociedades, haciéndolo parte de su cultura. Las banderas como símbolos de control territorial, empleando símbolos que representan a una familia, orden o armada fueron introducidas a el Nuevo Mundo (América) con la llegada de los conquistadores europeos al final del siglo XV. Las banderas/estandartes que representaban el dominio Real sobre territorios dominados, la iglesia católica y las banderas de ejércitos y/o conquistadores fueron las primeras en llegar al nuevo mundo. Una de aquellas banderas que ha soportado el paso del tiempo, teniendo un gran valor cultural tanto para las sociedades americanas como para las ibéricas, es el denominado Estandarte de armas de Francisco Pizarro. Siendo un objeto textil con decoración en hilos metálicos sobre un emblema Real. De acuerdo a fuentes históricas, este objeto fue usado por Francisco Pizarro en 1532 en el proceso de conquista del Perú, quien recibe por parte del Rey Carlos V el poder para que, en su nombre, Pizarro pueda conquistar las tierras del nuevo mundo hoy conocidas como Perú. Luego del dominio de Pizarro sobre el territorio Inca, se cree que Pizarro dejó su estandarte en la cima del templo Inca del sol como símbolo de su control. Siglos más tarde, en las campañas libertarias de América, el General Sucre, militar encargado de la armada independentista en Perú, reporta haber encontrado lo que él considera como el estandarte de Pizarro, enviándolo a Bogotá como muestra de victoria, siendo custodiada desde ese momento por el Museo Nacional de Colombia hasta la actualidad. Debido a discrepancias históricas, el verdadero significado del llamado estandarte de Pizarro ha sido objeto de discusión y debido del pasar del tiempo su estado de conservación se ha deteriorado. Dejando de este modo, un caso de estudio interesante para que por medio de estudios científicos al objeto se pueda dar respuesta a preguntas tanto históricas como de conservación del mismo. De este modo, por medio de una colaboración con el Museo Nacional de Colombia, se obtuvo un juego de 25 muestras del llamado Estandarte de armas de Francisco Pizarro, abarcando los diferentes componentes y áreas del objeto de estudio. Dichas muestras fueron sometidas a estudios analíticos para su caracterización físico-química. Análisis de observación al microscopio, análisis VSEM-EDS, espectroscopia Raman, análisis cromatográficos (HPLC-MS, GC-MS) y datación por radiocarbono catorce fueron realizados. Del mismo modo, por medio de una inspección física al objeto in situ y una profunda investigación en fuentes históricas del mismo, se buscó la información adecuada para resolver sus problemáticas. Los resultados obtenidos permitieron identificar como seda el textil empleado en la elaboración del estandarte, así como el uso de colorantes naturales para teñir las fibras en el emblema: uso de cochinilla y palo de Brasil como fuente del color rojo, plantas a base de luteolin para el color amarillo, plantas a base de indigotina para el color azul y mezcla de colorantes amarillos y azules para el color verde fueron identificadas. Del mismo modo se evidencio el uso de adhesivos animales y el uso de papel de trapos en el proceso de manufactura. El estudio de los hilos metálicos, permitió evidenciar el uso de alambres con núcleos de plata con un fino recubrimiento de oro en su exterior, siendo aplanados y entrelazados con hilos de seda para su uso. Finalmente usando la datación por radiocarbono, fue posible conocer con alta precisión que el estandarte fue elaborado entre los siglos XV-XVI y sufrió procesos de restauración con añadidura de textiles en tiempos modernos. Junto a lo anterior, es posible postular que el estado de degradación de la tela es debido a degradación natural en las fibras de seda, teniendo así que su color se ha desvanecido y sus propiedades mecánicas disminuidas, conllevando a perdida de rigidez y desaparición de la estructura. Del mismo modo se pudo conocer los colores originales del emblema y evidenciar problemas de desprendimiento del papel debido a cristalización del adhesivo. Asimismo, se comprobó que los hilos metálicos presentan corrosión por azufre y desprendimiento de sus cristales. Finalmente, combinando los resultados analíticos y la información de fuentes históricas encontradas del llamado Estandarte de armas de Francisco Pizarro, se puede postular que su elaboración fue realizada en Europa, usando materiales preciosos para obtener un objeto de larga vida con un profundo mensaje para sus observadores. También, los datos obtenidos ayudan a dar soporte la posible idea de que este objeto fue usado por Francisco Pizarro en el proceso de conquista del Perú. Sin embargo, debido a los símbolos presentes en el objeto, fecha y materiales de elaboración, este objeto es claramente único en su tipo, y lo más importante, por su mensaje lingüístico, este no representa a Francisco Pizarro o su armada, al contrario, representa a la Corona de España. Por ende, en vez de denominarse como Estandarte de armas de Francisco Pizarro, este objeto debería nombrarse como el Estandarte Real de la Colonia de Carlos V en el Nuevo Mundo.

Deposition of selenium thin layers on gold surfaces from sulphuric acid media: Studies using electrochemical quartz crystal microbalance, cyclic voltammetry and AFM

In this paper we report here new considerations about the relationship between the mass and charge variations (m/z relationship) in underpotential deposition (UPD), bulk deposition and also in the H(2)Se formation reaction. Nanogravimetric experiments were able to show the adsorption of H(2)SeO(3) on the AuO surface prior to the voltammetric sweep and that, after the AuO reduction, 0.40 monolayer of H(2)SeO(3) remains adsorbed on the newly reduced Au surface, which was enough to gives rise to the UPD layer. The UPD results indicate that the maximum coverage with Se(ads) on polycrystalline gold surface corresponds to approximately 0.40 monolayer, in good agreement with charge density results. The cyclic voltammetry experiments demonstrated that the amount of bulk Se obtained during the potential scan to approximately 2 Se monolayers, which was further confirmed by electrochemical quartz crystal microbalance (EQCM) measurements that pointed out a mass variation corresponding of 3 monolayers of Se. In addition, the Se thin films were obtained by chronoamperometric experiments, where the Au electrode was polarized at +0.10V during different times in 1.0 M H(2)SO(4) + 1.0 mM SeO(2). The topologic aspects of the electrodeposits were observed in Atomic Force Microscope (AFM) measurements. Finally, in highly negative potential polarizations, the H(2)Se formation was analyzed by voltammetric and nanogravimetric measurements. These finding brings a new light on the selenium electrodeposition and point up to a proposed electrochemical model for molecule controlled surface engineering. (c) 2009 Elsevier Ltd. All rights reserved.

Buildup of gold nanoparticle multilayer thin films based on the covalent-bonding interaction between boronic acids and polyols

A novel method for the fabrication of gold nanoparticle multilayer films based on the covalent-bonding interaction between boronic acid and polyols, poly(vinyl alcohol) (PVA), was developed. The multilayer buildup was monitored by UV-vis absorbance, spectroscopy, which showed a linear increase of the film absorbance with the number of adsorbed Au layers and indicated the stepwise and uniform assembling process. The atomic force microscopy (AFM) image showed that a compact gold multilayer thin film was successfully assembled. The residual boronic acid group on the surface of thin film Could incorporate glycosylated-protein horseradish peroxidase (HRP), and good catalytic activity for H2O2 could be observed.

Direct electrochemistry and surface plasmon resonance characterization of alternate layer-by-layer self-assembled DNA-myoglobin thin films on chemically modified gold surfaces

Alternate layer-by-layer (L-by-L) polyion adsorption onto gold electrodes coated with chemisorbed cysteamine gave stable, electroactive multilayer films containing calf thymus double stranded DNA (CT ds-DNA) and myoglobin (Mb). Direct, quasi-reversible electron exchange between gold electrodes and proteins involved the Mb heme Fe2+/Fe3+ redox couple. The formation of L-by-L (DNA/Mb), films was characterized by both in situ surface plasmon resonance (SPR) monitoring and cyclic voltammetry (CV). The effective thickness of DNA and Mb monolayers in the (DNA/Mb)l bilayer were 1.0 +/- 0.1 and 2.5 +/- 0.1 mn, corresponding to the surface coverage of similar to65% and similar to89% of its full packed monolayer, respectively. A linear increase of film thickness with increasing number of layers was confirmed by SPR characterizations. At pH 5.5, the electroactive Mb in films are those closest to the electrode surface; additional protein layers did not communicate with the electrode. CV studies showed that electrical communication might occur through hopping conduction via the electrode/base pair/Mb channel, thanks to the DNA-Mb interaction. After the uptake of Zn2+, a special electrochemical behavior, where MbFe(2+) acts as a DNA-binding reduction catalyst in the Zn2+-DNA/Mb assembly, takes place.

State-of-the-art of the Australian thin bed concrete structural masonry

With a view to minimising the spiraling labour costs, the concrete masonry industry is developing thin layer mortar technology (known as thin bed technology) collaboratively with Queensland University of Technology. Similar technologies are practiced in Europe mainly for clay brick masonry; in the UK thin layer mortared concrete masonry has been researched under commercial contract with limited information published. This paper presents numerous experimental data generated over the past three years. It is shown that this form of masonry requires special drymixed mortar containing a minimum of 2% polymer for improved workability and blocks with tighter height tolerance, both of which might increase the cost of these constituent materials. However, through semiskilled labour, tools to dispense and control the thickness of mortar and the associated increase in productivity, reduction to the overall costs of this form of construction can be achieved. Further the polymer mortar provides several advantages: (1) improved sustainability due to dry curing and (2) potential to construct mortar layers of 2mm thickness and (3) ability for mechanisation of mortar application and control of thickness without the need for skilled labour.