塔里木盆地柯坪-巴楚露头区白云岩成岩作用机理研究

Through field outcrop dolomite observation, laboratory petrography (macroscopy, microscopy, cathodeluminescence and scan electronic microscopy), geochemistry (carbon-oxygen-strontium isotopes and trace elements) and fluid inclusion microthermometry study in Keping-Bachu area of Tarim Basin, it can be inferred that there are existing eight dolomite texture types within four evolution phases in Keping-Bachu area of Tarim Basin. The paragenesis of different dolomite texture types and associated minerals in Keping-Bachu area has been established. The carbon and oxygen isotopes of saddle dolomites and matrix dolomites overlap greatly. The Strontium isotopes results of Keping-Bachu outcrop area show that the strontium isotopes differentiation of the matrix and saddle dolomites is not obvious, the reason of which is that there is thousands of Cambrian-Ordovician dolomite strata below the stratum bearing the saddle dolomite. In the process of the heat flow upward migration, the isotopes of the heat interacts with the host rock, which leads to the similarity betwwen the strontium of the saddle dolomite and matrix dolomite. The strontium isotope of the saddle dolomite is not very radiogenic. the six types samples within four phases in the study area show Eu negatively. Comparing to the other types of samples, the δEu of saddle dolomite is relatively high falling into the range of 0.510-0.874, which shows that the saddle dolomite forms in the hydrothermal setting and is affected by the hydrothermal activity to some extend.The Lan/Ybn of saddle dolomite is high up to 15.726, which means that the HREE is very rich. It belongs to the typical hydrothermal genesis model. The δCe of saddle dolomite is positive anomaly, which is the result of high effect from the land source debris. The homogeneous temperature of the saddle dolomite falls into two ranges 110-120℃ and 125-160℃, after pressure correction, they are 141-152℃，157.5-196℃, the salinity of the saddle dolomite can reach to 20-25%. With the comparing with the burial history, the Th of the saddle dolomite is high than the ambient strata temperature, these data show that the saddle dolomite is of hydrothermal origin. The evolution trend of different dolomite and associated minerals is from matrix dolomite, dolomite cementation, saddle dolomite, quartz to calcite. Alonging with this evolution trend, the temperature of the diagenetic flow initiated from 80-100℃, after rising to 135-160℃, then gradually declined. Finally, a structurally-controlled dolomitization model is established in Keping-Bachu area of Tarim Basin.

泥河湾盆地大长梁剖面岩石磁学和环境磁学研究

The fluvio-lacustrine sequence in the Nihewan Basin is an important archive of late Pliocene-Pleistocene climate and environment changes in temperate northern China, which provides excellent sources of early human settlements in high latitude East Asia. The recent years have witnessed a considerable progress in the paleomagnetic dating of its stratigraphy, which has notably increased our understanding of a series of important issues such as the early human occupation in the Old World, the infilling history of the Nihewan Basin, and the chronological sequence of the Nihewan faunas. Up to now, the long-term paleoenvironmental changes directly retrieved from this basin, which might influence the evolution and expansion of early humans in the Nihewan Basin, are still poorly constrained, although several paleoclimatic records have been retrieved from this area. In this study, a combined mineral-magnetic and geochemical investigation was carried out on the fluvio-lacustrine sequence from the Dachangliang section at the eastern margin of the basin in order to reveal its rock magnetic and environmental magnetic characteristics and its implications for early human evolution in East Asia. The major findings and conclusions are listed as the following: First, there is an increased cooling coupled with an intensified aridification recorded in the fluvio-lacustrine sequence of the Dachangliang section. The cooling is related to an up-section decrease in propensity to chemical weathering as inferred from an increase in low-field susceptibility after cycling to 700 °C. Close to 700 °C, reacting chlorite is providing the iron source for newly formed very fine-grained ferrimagnetic minerals which enhances the susceptibility signal. The reactivity of chlorite after annealing at temperatures above 600 °C is documented with X-ray diffraction. Second, degrees of chemical weathering in the Nihewan Basin are further estimated by clay mineralogy (i.e. chlorite and illite contents and chlorite/illite ratio) and a series of major element proxies (i.e. Na2O/Al2O3 versus K2O/Al2O3 diagram, Al2O3-(CaO + Na2O)-K2O ternary diagram (A-CN-K), chemical index of alteration (CIA), (CaO + Na2O + MgO)/TiO2, (CaO + Na2O + MgO + K2O)/(TiO2 + Al2O3), CaO/Al2O3 and CaO/TiO2). The up-section decrease in propensity to chemical weathering suggested by the aforementioned rock mangetic measurement is further confirmed by these geochemical analyses. Combining the chemical weathering records from the Nihewan Basin, Chinese Loess Plateau, South China Sea and eastern China, we find that the consecutive decreasing trend in chemical weathering intensity during the late Cenozoic is ubiquitous across China. This pattern may result from a long-term decreasing East Asian summer monsoon and increasing East Asian winter monsoon, and thus a consecutive increasing of aridification and cooling in Asia during the Quaternary. Furthermore, the chemical weathering intensity increased from South China to North China during the Quaternary, in line with the decreasing East Asian summer monsoon and increasing East Asian winter monsoon and thus the gradually intensified aridification and cooling from South China to North China. Third, a combined mineral-magnetic and geochemical investigation provides evidences that the large-amplitude alterations of concentration of magnetic minerals mainly result from preservation/dissolution cycles of detrital magnetic minerals in alternately oxic and anoxic depositional environments. The preservation/dissolution model implies that the high-magnetic and low-magnetic cycles of this sedimentary sequence represent glacial and interglacial climate cycles, respectively. This contribute significnatly to our understanding of the link between climate and magnetic properties. Finally, the paleoclimatic implications of these rock magnetic and geochemical characteristics significantly increase our understanding of the general setting of early humans in high northern latitude in East Asia. We propose that the cold and dry climate may have contributed significantly to the expansion and adaptation of early humans, rather than bringing hardship, as is often thought. The relationship between magnetic properties and climate possibly provides valuable information on the climatic context of the Paleolithic sites in the basin, especially whether the occupation occurred during an interglacial or glacial period.

塔里木盆地寒武－奥陶系白云岩类型、成因机理及其孔隙性研究

Cambrian-Ordovician dolostones in Tarim Basin are hydrocarbon reservoir rocks of vital importance. Under the guidance of the theories of sedimentology and the sedimentology of carbonate reservoir, based on the first-hand qualitative and quantitative data especially, combined with micro-study, geochemical and reservoir capacity analysis, and precursor research, the origin and reservoir characteristics of the dolostones were discussed. Based on detailed petrographic investigations, four types of dolostone have been recognized, which are, respecitively, mud-silt-sized dolostones, algal laminated dolostones (ALD), prophyritic dolostone, and neomorphic dolostone. Mud-silt-sized dolostones always presents as laminas together with evaporated signatures, its REE patterns and ΣREE are all close to that of the finely crystalline limestone. This kind of dolomite probably experienced relatively low fluid-rock ratio during diagenesis was formed in hypersaline and oxidizing environment and involved fast dolomitization process. It was dolomitized by evaporated seawater in sabkha environment.The main primary fabrics of algal lamination in algal laminated dolomite (ALD) can still be identified and its ΣREE (21.37) is very close to that of algae. This reveals that ALD was dolomitized during early diagenesis and algae possibly played an important role. The ALD was formed under mediation of organic matter and Mg2+ were supplied by magnesium concentrated algal laminites and sea water. Prophyritic dolostones presents mainly as patchy occurrence and yield the lowest δ13C and Z value. Its ΣREE is much less than that of the finely crystalline limestone. These characteristics reveal that the cloudy cores were dolomitized in shallow early diagenetic environments by pore fluids riched in Mg2+. Whereas the clear rims were likely formed in subsequent burial into deeper subsurface environments, and the Mg2+ needed for further dolomitization possibly was supplied by the transformations of clay minerals. Neomorphic dolostones consist of coarse, turbid crystals and exhibits sucrosic and mosaic textures. It has highest Fe2+ contents and average homogeneous temperature (110.2℃). Collectively, these characteristics demonstrate that the neomorphic dolostones was likely formed by recrystallization of pre-existing dolomites during deep burial. The ΣREE of the four types of dolostone distinctly differentiates from each other. However, their REE patterns are all enriched in LREE, depleted in HREE and have Eu negative anomalies. Its ΣREE 13.64 ppm, less than 1/4 of finely crystalline limestone, and ranks the lowest in the 4 types.These characteristics are comparable to those of finely crystalline limestone, and are mainly infuenced by the sea water. These four types of dolostone show similar REE mobility behaviour and no significant fractionation, althouth they have been subjected to evidently different diageneses. Seven main pore types are identified in the dolostones , which are fenestral, moldic, intercrystal, dissolved，breccia, dissolved breccia and stylolite pores. Fenestral pores are primary and the others are secondary. The dissolved pores and intercrystal pores are the most important reservoir spaces and followed by breccias and dissolved breccia pores, and the moldic and fenestral pores are less important. Stylolites can enhance permeability of reservoir rocks in one hand, for the other hand, the capacity of reservoir and permeability are enhanced and then better reservoir rocks can be formed when they are combined with patchy dolostones. The relationship between porosity and the type of dolostones is that the dissolved neomorphic dolostones have the highest porosity of 3.65%, than followed by dissolved Mud-silt-sized dolostones of 3.35%. The mud-silt-sized dolostones without dissolution have the lowest porosity of 0.90%. Moreover, the porosity of prophyritic dolostones and the neomorphic dolostones without dissolution are lower, respectively 1.675% and 1.41%. Although algal laminated dolostones consist of euhedral crystals and riched in intercrystal pores, its porosity just yields 1.20%. The relationship between permeability and the type of dolostones is that that algal laminated dolostones have the highest permeability of 0.462mD and followed by 0.065mD of prophyritic dolostones. Dissolution have no significant influence on the permeability of neomorphic dolostones and this presented by the permeability of dissolved and non-dissolved are very close, respectively 0.043mD and 0.062mD. No matter dissolved or not, mud-silt-sized dolostones are much less permeable. The permeability of non-dissolved and dissolved are 0.051mD and 0.016mD. Collectively, in the study area, neomorphic dolostones can form high quality reservoir.

温度、压力耦合背景下多相流体运移的数学模型研究

The Mathematical modeling of multiphase fluid flow is an important aspect of basin simulation, and also is a topic of geological frontier. Based on coupling relation of temperature, pressure and fluid flow, this dissertation discusses the modeling which conform to geological regularities of fluid migration. The modeling that is multi-field and multiphase includes heat transport equation, pressure evolvement equation, solution transport equation and fluid transport equation. The finite element method is effective numerical calculation methods. Author applies it to solve modeling and implements the finite element program, and the modeling is applied to Ying-Qiong Basin. The channels of fluid vertical migration are fault, fracture and other high penetrability area. In this thesis, parallel fracture model and columnar channel model have been discussed, and a characteristic time content and a characteristic space content been obtained to illustrate the influences of stratigraphic and hydrodynamic factors on the process. The elliptoid fracture model is established and its approximately solution in theory is gotten. Three kinds of modeling are applied to analyze the transient variation process of fluid pressure in the connected permeable formations. The elliptoid fracture model is the most similar geology model comparing with the other fracture models so the research on this fracture model can enhance the understanding to fluid pressure. In the non-hydrodynamic condition, because of the difference between water density and nature gas density, nature gas can migrate upon by float force. A one-dimension mathematical model of nature gas migration by float force is established and also applied to analyze the change in the saturation of gas. In the process of gas migration its saturation is non-continuous. Fluid flow is an important factor which influences the distribution of the temperature-field, the change of temperature can influence fluid property (including density, viscidity, and solubility),a nd the temperature field has coupling relations to the fluid pressure field. In this dissertation one-dimension and two-dimension thermal convection modeling is developed and also applied to analyze convective and conductive heat transfer. Author has established one-dimension and two-dimension mathematical modeling in which fluid is a mixture of water and nature gas based on the coupling relation between temperature and pressure, discussed mixture fluid convection heat transfer in different gas saturation, and analyzed overpressure form mechanism. Based on geothermal abnormity and pore pressure distribution in Dongfong 1-1, Yinggehai Basin, South China Sea, one-dimension mathematical modeling of coupling temperature and pressure is established. The modeling simulates the process that fluid migrates from deep to shallow and overpressure forms in shallow. When overpressure is so large that fractures appear and overpressure is released. As deep fluid flow to shallow, the high geothermal then forms in shallow. Based on the geological characteristics in Ya13-1, two-dimension mathematical modeling of coupling temperature and pressure is established. Fluid vertically flows in fault and then laterally migrates in reservoir. The modeling simulates the geothermal abnormity and pore pressure distribution in reservoir.

流体地球化学：成因、流动和流体-岩石相互作用及塔里木盆地实例研究

Geofluid in sedimentary basins is related to petroleum generation, migration, accumulation and preservation, and is a topic of geological frontier. By integrating the multi-discipline methods of petroleum geochemistry, sedimentology, hydrogeology, petroleum geology and experimental geochemistry, the thesis has carried out experiments of microcline dissolution in solutions with organic acids, crude oil, brines with high total dissolved solids (TDS), and has dealt with Al distribution between the crude oil and the brines after the experiments. Cases for study includes Central Tarim, Hetianhe Gas Field and Kucha forland basin with data containing fluid chemistry and isotopic compositions, thin sections of sandstones and carbonates, homogenization temperatures and salinities of fluid inclusions, isotopic compositions of bulk rock and autigenic minerals. The aims are to elucidate fluid origin and flow in the three areas, effect of hydrocarbon emplacement on diagenesis, and to show occurrence of microbe-mediated, and thermochemical sulfate reduction in the Tarim Basin. Microcline dissolution experiments show that after 100 hour, part of the dissolved Al distributes in the crude oil, and the Al concentrations in the crude oil rise when organic acids are added. The result can be used to explain that most oilfield waters in the Tarim Basin are characterized by less than 3mg/L Al. Crude oil added to the solutions can enhance microcline dissolution, which is also observed in the case - Silurian sandstones with early crude oil emplacement in the Central Tarim. Al and Si have higher concentrations in the experiments of oxalic acid than of acetic acid under the same pH conditions, suggesting that there exist Al-oxalate and Si-oxalate complexes. Presence of acetate can enhance the activity of Ca and Al, but Al concentrations have not been increased significantly due to formation of small Al-acetate complex during the experiments. Relationships between δD and δ~(18)O in conjunction with chemistry of oilfield waters show that the waters are evaporated connate waters, which subsequently mixed with meteoric water, and were influenced by water-rock interactions such as salt dissolution, dolomitization of calcite, albitization of feldspar. In the Hetianhe Gas Field where salt dissolution took place, δD and δ~(18)O values can be used to trace nicely meteoric water recharge area and flow direction, but TDS can not. Part of the waters have high TDS but very light δD and δ~(18)O. When combined with paleo-topography, or fluid potentials, meteoric water is suggested to flow eastward in the Hetianhe Gas Field, which is the same with the Central Tarim. Whist in the Kuche forland basin, meteoric water may have permeated Cambrian-Ordovician strata. Relationship between ~(87)Sr/~(86)Sr and 1/Sr can be used to indicate migration and mixing of brines from carbonate strata (low ~(87)Sr/~(86)Sr ratio but high Sr content), clastic strata (high ~(87)Sr/~(86)Sr ratio but low Sr content) and crystalline basement (high ~(87)Sr/~(86)Sr ratio and heavy δ~(18)O value). Using this approach, it can be found that ~(87)Sr-depleted brine from Ordovician carbonates have migrated up to and mixed with ~(87)Sr-enriched waters from Silurian and Carboniferous sandstones, and that Silurian brines have mixed with meteoric water. In the Kuche forland basin, brines from the Cambrian and Ordovician carbonates have higher ~(87)Sr/~(86)Sr ratios than those from the overlying sandstones, when combined with chemistry, δ~(15)N and ~3He/~4He ratios of the coexisting natural gases, suggesting that the brines were derived from the basement. There exists some debate on the effect of hydrocarbon emplacement on mineral diagenesis. Case-study from Silurian sandstones in the Central Tarim show that quartz has kept overgrowing secondarily when oil saturation was decreased by meteoric water flushing subsequently to hydrocarbon emplacement. Silicon precipitates on the water-wet quartz surface, leading to decreased Si concentration close to the surface. A Si grads can result in Si diffusion, which supplies Si for quartz overgrowth. Hydrocarbon oxidation-sulfate reduction is an important type of organic-inorganic interaction. Not only can it make secondary alteration of hydrocarbons, but generate H_2S and CO_2 gases which can improve reservoir property. Thermochemical sulfate reduction took place at the temperatures more than 125 ℃ to 140 ℃ in the Cambrian-Ordovician carbonates, the products - H_2S and CO_2 gases migrated up to the Silurian, and precipitated as pyrite and calcite, respectively. The pyrite has an average δ~(34)S value close to those of Ordovician seawater and anhydrite, and calcite has δ~(13)C value as low as -21.5‰. In the Hetianhe Gas Field, sulfate reduction bacteria carried by meteoric water flowing eastward may have preferentially depleted ~(12)C of light hydrocarbon gases, and results in heavier δ~(13)C values of the residual hydrocarbon gases and higher molar CO_2 in the natural gases in the west than in the east. Coexisting pyrite has δ~(34)S values as low as -24.9‰.

改造型盆地油气成藏机理与油气预测－以银根－额济纳旗盆地为例

Reformed basin is a basin that underwent multiple immense reformation after the sedimentary stage, the major geologic elements of the petroleum system in the prototyped basin are destroyed to a certain extent, and their petroleum system has been reconstructed. This type of basin is frequently found in the course of exploration both home and abroad. In China, especially in the western and southern part of China, the basins in which oil explorations have been conducted are mostly reformed basins. The reformed basins from Paleozoic, Late Mesozoic to Cenozoic are widely distributed in West and South China. They are, and moreover, will be a challenge for oil and gas exploration. The conventional investigation and exploration techniques used in the slightly reconstructed basin just don't work well when facing the reformed basin. Therefore, the study on the reformed basin, especially the study on the pool-forming mechanism and reservoir prediction becomes a focus and one of difficulties for the geologists overseas and domestic. Yingen-Ejinaqi Basin is a typical case of the Late Mesozoic and Cenozoic reformed basins in China. It locates in West China and is a exploration frontier with difficulties and no break through is made for years. A comprehensive research on it will be of significance for oil and gas exploration in similar basins of China. The late research for reformed basin in China now is mainly concentrated on basin classification, formation mechanism, geologic features, and survey technique, distribution regularity of oil accumulation and its dominating factors, assessment of oil exploration prospect and target zones, etc. On the other hand, the study on the pool-forming mechanism and reservoir prediction seems insufficient in systematization, and the research is deficient in methodology and combination of qualitative and quantitative studies, as well as the application of the new theory and techniques. The current efforts are mainly directed to structures (faults), sedimentation, the relationship between reservoir evolution and oil accumulation, and some other relevant fields. However, the application of the new theory and techniques seems to be insufficient such as petroleum system, pool-forming dynamics, fluid pressure compartment, and basin simulation, etc. So is the dynamic and integrated research. As a result, incomplete knowledge and understandings derived from the research on pool-forming mechanism and reservoir prediction often do not accord with rea-lity of the basin. The study and exploration under the guidance of this knowledge will inevitably lead to errors and failure. This paper, based on the previous study of the other geologists on reformed basins, with emphasis on "wholeness or systematic, dynamic and integrated" research, presents a reverse thinking of beginning from conserved units in the basin and the combination of qualitative and quantitative study with new theory and technique by building a geological model. The paper also puts forward a new thought for studying the oil & gas accumulation and reservoir prediction , and establishes a new research system for reformed basin. It is verified by the known reservoir and oil accumulation area in the basin and has a practical value for use and reference. The new ideas and achievements in this research are as following: 1.This is the first time that the system for studying the reformed basin and its pool-forming mechanism and reservoir prediction is presented. A reverse thinking and combination of qualitative & quantitative are applied here with emphasis on "wholeness or systematic, dynamic and integrated" research, new theory, techniques & methods comprehensive use and geologic models building. 2. Identifying criterion and methods, classifying schemes, and denominating principles for the conserved units of reformed basins are presented in this paper. The geologic model of conserved units of Yingen-Ejinaqi Basin has been built. It is a practical method when combined with the traditional way for basin survey and the conserved units study. 3.The dynamic sources of basin deformation are believed to be stress, gravity and thermodynamics. The stress and gravity are key factors in basin deformation and pool forming, especially stress. Scientific proof is provided by classifying the functional type, style and range of the stress, gravity and thermodynamics. 4.The pool forming and reservoir distribution of Yingen-Ejinaqi Basin are controlled by multiple factors or geologic conditions or/and co-controlled by both of them. The qualitative and quantitative research on petroleum system and basin modeling will help us understand and determine the pool-forming period of the conserved unit (timing), the oil migrating direction (orientation), the oil accumulating region (location), the oil distributing border (bordering) and the size of oil accumulation (quantification). Thus the pool-forming and distribution zones can be predicted. 5.Three generating modes (reform-succession type, reform-destroyed type and reform-regenerating type or reform-newborn type) of pool forming for reformed basins are presented here, together with the inner relationships between basin deformation type, overlapping style and pool-forming modes. The pool-forming modes are determined by deformation type and overlapping style. Reservoir distribution will be predicted based on the modes and other concrete pool-forming conditions. 6.The evaluation methods of the conserved units and zones and the parameter selection are reliable in optimal selecting of target zones. The technical terms, new ideas and methods for the study of reformed basins, the pool-forming mechanism and reservoir prediction are presented in this paper. The concepts and terms, the identifying criterion, the denominating principles, the generating modes for pool forming, the methods of reservoir prediction, and the evaluation techniques for conserved units and zones can be used for reference in studies on the petroleum exploration of reformed basins in China and abroad. It serves as a typical example for further research of the reformed basins and the geologic regulations of oil accumulation. It has a practical value of use and reference. The future research in the field of pool-forming mechanism of the reformed basins may well be on the process simulation of pool-forming dynamics of the reformed basins. Experimental work has been conducted to simulate the processes by using quantitative and qualitative methods combined. The further study in this field calls for more efforts.

中国北方草本植物及表土有机质碳同位素组成

Recently, more and more attention has been paid to stable isotope ratios in terrestrial depositional systems. Among them, δ~(13)C value is mainly determined by the surface vegetation, while vegetation is directly related to climate, therefore, carbon isotope ratio in soil organic matter and pedogenic carbonate has been employed as an important paleoecological indicator. In order to test the paleoecological information extracted from stable isotope ratios in terrestrial depositional systems, it is necessary to study the relationships between δ~(13)C value in standing terrestrial plants and today climate, as well as between δ~(13)C value in modern surface soil organic matter and standing vegetation. Thus, these relationships were studied in this paper by means of analysing δ~(13)C in standing plants and modem surface soil organic matter in North China. The main results and conclusions are presented as following: 1. According to their δ~(13)C values, 40 C-4 species represent about 16% of the 257 plant species sarnpled from the North China. C-4 photosynthesis mainly occurs in Poaceae, Cyperaceae and Chenopidaceae families, and percentage representation of C-4 photosynthesis is up to 56% in Poaceae family. 2. The δ~(13)C values of C-3 plant species in North China vary from -21.7‰ to -32.0‰ with an average of -27.1‰, and 93% focus on the range of -24.0‰ ～ -30.0‰; δ~(13)C values of C-4 plant species in North China are between -10.0‰ ～ -15.5‰ with an average of -12.9‰, and 90% concentrate on the range of -11.0‰ ～ -15.0‰. 3. The δ~(13)C composition of C-3 plant species collected from Beijing, a semi-moist district, mainly vary between -27.0‰ ～ -30.0‰, and the average is -28.7‰; the δ ~(13)C values of plants in the semi-arid district, east and west to the Liu Pan Moutain, focus on the range of-26.0‰ ～ -29.0‰ and -25.0‰ ～ -28.0‰, respectively, with the mean value of -27.6‰ and -26.6‰, respectively; the δ~(13)C composition in the arid district dominantly vary from -24.0‰ to -29.0‰, with the average of -26.2‰, and among them, the δ~(13)C values of C-3 plant species in deserts are often between - 22‰ ～ -24‰; the δ~(13)C values in the cold mountain district concentrate on the range of -24.0‰ to -29.0‰, with the average of -26.3‰. 4. The main range of δ~(13)C composition of C-4 plant species, derived from Beijing, a semi-moist district, are -13.0‰ ～ -15.5‰; the semi-arid district, -11.0‰ ～ -14.0‰; the arid district, -11.0‰ ～ -14.0‰. The mean values of them are -14.0‰, -12.4‰,-12.7‰, respectively. 5. From east to west in North China, δ~(13)C values of C-3 plant species increase with longitude. The correlation between δ~(13)C ratios of C-3 plant species and longitude is linear. Changing temperate and precipitation and changing atmosphere pressure are spossible explanations. 6. Almost all C-3 plant species have the trends that their δ~(13)C values gradually increase with decreasing precipitation, decreasing temperature and increasing altitude. Our results show the increases of the δ~(13)C value by 0.30 ～ 0.45‰, 0.19 ～ 0.27‰ and 1.1 ～ 1.2‰ per 100 mm, I℃ and 1000 m, respectively, for all C-3 plant species together. 7. The δ~(13)C values of all C-3 plant species together and a part of C-3 species show highly significant linear correlation with the mean annual temperature, the mean annual precipitation and the altitude, and the results suggest that they can be used as proxies of these environmental variables, while, those without highly significant correlation, may be not suitable as the proxies. 8. The extent, which of responses of δ~(13)C composition to environmental variables, is different for each C-3 plant specie. 9. The δ~(13)C variations along altitude and longitude may be non-linear for C-4 p1ant species in North China. The mean annual temperature may be not important influential factor, thus, it suggests that the δ~(13)C composition of C-4 plant species may be not suitable as the proxy of the mean annual temperature. The influences of summer temperature on δ~(13)C values are much bigger than that of annual temperature, among them, the influence of September temperature is biggest. The mean annual precipitation may be one of the dominant influential factors, and it shows a highly significant non-linear relationship with δ~(13)C values, and the result indicates that δ~(13) C composition of C-4 plant species can be employed as the proxy of the mean annual precipitation. 10. The variations of δ~(13)C ratios do not show systematic trends along longitude, latitude and altitude for modern surface soil organic in Northwest China. ll. The δ~(13)C ratios of modern surface soil organic do not exhibit systematic patterns with temperature and precipitation in Northwest China, it suggests that, unless soil organic is transferred from pure C-3 or C-4 vegetation, the δ~(13)C composition of soil organic may be not used as proxies of climatic variables. 12. The δ~(13)C values of modem surface soil organic are heavier than that of standing vegetation, and the difference ofrnean δ~(13)C between them is -2.18‰. 13. Without considering the δ~(13)C difference between vegetation and soil organic, as well as the δ~(13)C drift in various enviromnent, we may not obtain the valuable information of C-3, C-4 relative biomass in vegetation. 14. The C-4 biomass contribution in vegetation increase with decreasing latitude, increasing longitude and decreasing altitude in Northwest China. The C-4 biomass almost are zero in those regions north to 38 ° N, or west to 100°E, or above 2400 m. 15. The C-4 relative biomass in vegetation increase with growing temperature and precipitation. and, C-4 plants are rare at those regions where the mean annual temperature is less 4 ℃, or the mean annual precipitation is less 200 mm, and their biomass contribution in vegetation are almost zero. Both the mean annual temperature and the mean annual average precipitation may be the important influential factors of C-4 distribution, but the dominant factors.

生物－热催化过渡带沉积成岩演化及其成烃作用研究

The biothermocatalytic transitional zone gas is a new type of natural gas genetic theory, and also an clean, effective and high quality energy with shallow burial depth, wide distribution and few investment. Meanwhile, this puts biothermocatalytic transitional zone gas in important position to the energy resource and it is a challenging front study project. This paper introduces the concept, the present situation of study and developmental trend about biothermocatalytic transitional zone gas in detail. Then by using heat simulating of source rocks and catalysis mechanism analysis in the laboratory and studying structural evolution, sedimentation, diagenesis and the conditions of accumulation formation and so on, this paper also discusses catalytic mechanism and evolutionary model of the biothermocatalytic transitional zone gas formation, and establishes the methods of appraisal parameter and resources prediction about the biothermocatalytic transitional zone gas. At last, it shows that geochemical characteristics and differentiated mark of the biothermocatalytic transitional zone gas, and perfect natural gas genetic theory, and points out the conditions of accumulation formation, distribution characteristics and potential distribution region on the biothermocatalytic transitional zone gas m China. The paper mainly focuses on the formation mechanism and the resources potential about the biothermocatalytic transitional zone gas. Based on filed work, it is attached importance to a combination of macroscopic and microcosmic analysis, and the firsthand data are obtained to build up framework and model of the study by applying geologic theory. Based on sedimentary structure, it is expounded that structural actions have an effect on filling space and developmental cource of sediments and evolution of source rocks. Carried out sedimentary environment, sequence stratigraphy, sedimentary system and diagenesis and so on, it is concluded that diagenesis influences developmental evolution of source rocks, and basic geologic conditions of the biothermocatalytic transitional zone gas. Applying experiment simulating and catalytic simulating as well as chemical analysis, catalytic mechanism of clay minerals is discussed. Combined diagenecic dynamics with isotope fractionation dynamics, it is established that basis and method of resource appraisal about the biothermocatalytic transitional zone gas. All these results effectively assess and predict oil&gas resources about the biothermocatalytic transitional zone gas-bearing typical basin in China. I read more than 170 volumes on the biothermocatalytic transitional zone gas and complete the dissertation' summary with some 2.4 ten thousand words, draw up study contents in some detail and set up feasible experimental method and technologic course. 160 pieces of samples are obtained in oilfield such as Liaohe, Shengli, Dagang and Subei and so on, some 86 natural gas samples and more than 30 crude oil samples. Core profiles about 12 wells were observed and some 300 geologic photos were taken. Six papers were published in the center academic journal at home and abroad. Collected samples were analysised more than 1000 times, at last I complete this dissertation with more than 8 ten thousand words, and with 40 figures and 4 plates. According to these studies, it is concluded the following results and understandings. 1. The study indicates structural evolution and action of sedimentary basin influence and control the formation and accumulation the biothermocatalytic transitional zone gas. Then, the structural action can not only control accommodation space of sediments and the origin, migration and accumulation of hydrocarbon matters, but also can supply the origin of energy for hygrocarbon matters foramtion. 2. Sedimentary environments of the biothermocatalytic transitional zone gas are lake, river and swamp delta- alluvial fan sedimentary systems, having a warm, hot and humid climate. Fluctuation of lake level is from low to high., frequency, and piling rate of sedimentary center is high, which reflect a stable depression and rapidly filling sedimentary course, then resulting in source rocks with organic matter. 3. The paper perfects the natural gas genetic theory which is compound and continuous. It expounds the biothermocatalytic transitional zone gas is a special gas formation stage in continuous evolutionary sequence of organic matter, whose exogenic force is temperture and catalysis of clay minerals, at the same time, having decarbxylation, deamination and so on. 4. The methodology is established which is a combination of SEM, TEM and Engery spectrum analysis to identify microstructure of crystal morphology about clay minerals. Using differential thermal-chromatographic analysis, it can understand that hydrocarbon formation potential of different typies kerogens and catalytic method of all kinds of mineral matrix, and improve the surface acidity technology of clay minerals measured by the pyridine analytic method. 5. The experiments confirm catalysis of clay minerals to organic matter hygrocarbon formation. At low temperature (<300 ℃), there is mainly catalysis of montmorillonite, which can improve 2-3 times about produced gas of organic matters and the pyrolyzed temperature decreased 50 ℃; while at the high temperature, there is mainly catalysis of illite which can improve more than 2 times about produced gas of organic matters. 6. It is established the function relationship between organic matter (reactant) concentration and temperature, pressure, time, water and so on, that is C=f (D, t). Using Rali isotope fractionation effect to get methane isotope fractionation formula. According to the relationship between isotope fractionation of diagenesis and depth, and combined with sedimentary rate of the region, it is estimated that relict gas of the biothermocatalytic transitional zone gas in the representative basin. 7. It is revealed that hydrocarbon formation mechanism of the biothermocatalytic transitional zone gas is mainly from montmorillonite to mixed minerals during diagenesis. In interlayer, a lot of Al~(3+) substitute for Si~(4+), resulting in a imbalance between surface charge and interlayer charge of clay minerals and the occurrence of the Lewis and Bronsted acid sites, which promote to form the carbon cation. The cation can form alkene or small carbon cation. 8. It is addressed the comprehensive identification mark of the biothermo - catalytic transitional zone gas. In the temproal-spatial' distribution, its source rocks is mainly Palaeogene, secondly Cretaceous and Jurassic of Mesozoic, Triassic, having mudy rocks and coal-rich, their organic carbon being 0.2% and 0.4% respectively. The vitrinite reflection factor in source rocks Ro is 0.3-0.65%, a few up to 0.2%. The burial depth is 1000-3000m, being characterized by emerge of itself, reservoir of itself, shallow burial depth. In the transitional zone, from shallow to deep, contents of montmorillonites are progressively reduced while contents of illites increasing. Under SEM, it is observed that montmorillonites change into illite.s, firstly being mixed illite/ montmorillonite with burr-like, then itlite with silk-like. Carbon isotope of methane in the biothermocatatytic transitional zone gas , namely δ~(13)C_1-45‰- -60 ‰. 9. From the evolutionary sequence of time, distribution of the biothermocatalytic transitional zone gas is mainly oil&gas bearing basin in the Mesozoic-Neozoic Era. From the distribution region, it is mainly eastern stuctural active region and three large depressions in Bohaiwang basin. But most of them are located in evolutionary stage of the transitional zone, having the better relationship between produced, reservoir and seal layers, which is favorable about forming the biothermocatalytic transitional zone gas reservoir, and finding large gas (oil) field.

塔里木盆地奥陶系不整合面岩溶作用特征与油气储层研究

Based on the principle and methods of carbonate sedimentology and reservoir geology, and guided by the theories of carbonate reservoir geology, the palaeokarst of Ordovician carbonate rocks in Tarim Basin has been comprehensively studied with multiple methods from different branches of geology. It is indicated that the features and distribution of palaeokarstification have developed in Ordovician carbonates. The controlling of karstification to Ordovician carbonate reservoirs has been discussed. Regional distribution of carbonate reservoirs controlled by karstification has been predicted within this basin. The main consents and conclusions of the this dissertation is as follows: Nine key indicators to the recognition of palaeokarst are proposed in terms of careful observation upon the well cores, lithological and geochemical analyses, and drilling and logging responses to the karst caves and fractures. The time and environment of cave filling are documented from careful research of lithofacies, mineralogy, and geochemistry of the physical and chemical fillings within karst caves. The caves in Ordovician carbonates were filled in Early Carboniferous in Lunnan area. The muddy filling in upper caves was deposited under subaerial fresh-water setting, while the muddy filling in lower caves was formed in the mixed water body of fresh-water and dominated sea water. Although most chemical fillings are suggested being precipated in the burial diagenetic environment after karstification but mineralogic and geochemical characteristics of some chemical fillings indicates they formed in meteoric environment during the karstification. It is obvious that the palaeokarst has been zoned in vertical profile. It can be divided into four units from top to bottom: surface karst, vadose karst, phreatic and tranquil flow zones. Between two types of limestone karst and dolostone karst are firstly differentiated in Tarim Basin, based on the comparison of features of each karst zone in limestone and dolostone regions. In Tabei area, the lowest depth of karstification is approximately 300 m below the Upper Ordovician unconformity interface, while the bottom depth of karstification in Tazhong area ranges commonly from 300 to 400 m, in rare cases may be up to 750 m below the upper Ordovician unconformity interface. In Lunnan and Tazhong areas, the palaeokarst morphology and the surface hydrosystem are firstly reconstructed based on the top of carboniferous "Shuangfeng limestone bed (Double-Peaks limestone)" as basal. According to the palaeomorphologic feature, karst topography can be divided into three units: karst upland, karst slope, and karst valley. Vadose zone was well developed in karst upland, and it can be found in a quite depth. Both vadose and phreatic zones were well developed in karst slope and upstream valley. In downstream valley, the karstification is not strong, the vadose and phreatic zones are thin in thickness. In Tazhong and Yingmaili areas, karstification is also developed in relict carbonate palaeo-hills which existed as isolated blocks admits clastic strata.

塔里木盆地塔中地区寒武-奥陶系烃源岩古地温及成烃演化史研究

The present maturity of Cambrian and Ordovician source rocks in Tazhong area, Tarim basin, is studied using several organic petrology methods and conodont CAI method. The highest palaeotemperature that the Cambrian-Ordovician undergone is revealed by Laser Roman Microprobe (LRM) analysis and by simulating experiment of the kerogen chemical kinetics. In according to all above study, the thermal history of Cambrian and Ordovician is reconstructed based on numerical simulating approaches. The characteristics of secondary hydrocarbon generating are studied by inclusions analysis. The reflectances of the samples in the drills located in Tazhong area show that the maturities of Cambrian source rocks are in the stages of condense oil-dry gas, and that of Ordovician source rocks range from peak of oil generating to wet gas stage. The palaeotemperature data of Cambrian-Orovician source rocks from well Tacan 1, based on LRM analysis, are in coincidence with that from other methods. Also are the palaeotemperature data of Cambrian-Orovician source rocks in well Tacan 1 based on the simulating experiments of kerogen pyrolysis, similar to the homogenization temperatures of inclusions in the source rocks. Aaccording to the vitrinite inflectance data of the TZ12 well and Tacan 1 well, the paleotemperature gradients are analysized and reconstructed. These data show that the paleotemperature gradient in Tazhong area was the highest during Cambrian-Ordovician period, it was up to 3.5°C/100m. Following, the temperature gradient descended gradually and it reached to the lowest at present (2.2°C/100m). The histories of maturation and hydrocarbon generation of Cambrian and Ordovician source rocks in Tazhong area are researched systematically and quantitatively, the results show that periods of oil generation from Cambrian and Ordovician source rocks lasted for a long time from Ordovician to Carbonferious periods because the central Cambrian stratum in the north slope of Tazhong area is buried differently in depth. The top of the Cambrian entered into the peak of oil generation in middle-late Ordovician, and most area of the north slope of Tazhong area entered into the peak of oil generation in Carbonferious period, and on the uplift belt some of source rocks entered into the peak of oil generation in Permian period. In early Devonian, the central of the Lower Ordovician source rocks near the Manjiaer depression reached the peak of oil generation and near the top of the Tazhong uplift did not reached the peak of oil generation until early Cretaceous. The middle-upper Ordovician entered into the peak of oil generation in early-middle Jurassic. The time of the middle-upper Ordovician in the top of the uplift belt entering into the peak of oil generation was delayed, because the source rock was buried shallowly, and it did not reached the peak of oil generation until middle Cretaceous. Middle-upper Ordovician in the top of the north slope has been in the peak of oil generation now, it is consistent with the maturity (1.0-1.2%Ro) of the source rocks. The characteristics of the inclusions formed by kerogens are different from that by crystal-enclosed organic matters(OM) during secondary hydrocarbon generation of Cambrian and Ordovician source rocks. The secondary hydrocarbon generation mainly occurred in Mesozoic-Cenozoic period, in an area of about 9000km2 in the north slope. The intensity of the secondary hydrocarbon generation of Cambrian and Ordovician is up to 21kg/torg and 36kg/torg) respectively. Using the staged gas chromatography, the high-over maturated carbonate source rocks are analysized to release the adsorbed OM, inclusions OM and crystal-enclosed OM, respectively, and to evaluate their relative contributions to secondary hydrocarbon generation. The three periods of oil and gas migration and petroleum pools formation in Tazhong area are determined according to organic inclusions and solid bitumen.

富硫流体的成因与硫酸盐还原作用研究

Origins of H_2S, thiols, thiophenes in natural gases and sulphur-enriched oils are complicated and thus some debates exist on them. The post-doctoral research is based upon oil- and gas-field data. Cases for study include Triassic Jianglingjiang Formation natural gases, Wolonghe Field, Sichuan Basin, Paleozoic oils and bitumen, Central Tarim, gases reserviored nearby Carboniferious - Ordovician unconformity, Hetianhe Field, Tarim Basin and sulphur-enriched oils in Tertiary reserviors in Jinxian Sag, Bohai Bay Basin. We have carried out analyses on the oils and gases for chemistry, δ~(13)C, δ~(34)S, and molecular composition of biomarkers, analyzed authigenetic pyrite forδ~(34)S, formation water for chemistry and δD and δ~(18)O along with petroleum system and burial history analyses, The aims are to assess the origins of the H2S and authigenetic pyrite, to discuss the possibility of reduced sulphur incorporation into hydrocarbons and to determine the mechanisms of hydrocarbon secondary alteration in the above four cases by comparison. The research shows that the reduced sulphur in the four cases is the result of thermochemical and biological sulphate reduction., TSR and BSR, respectively. No evidence indicates an origin of decomposition of organic matter or mantle - derived H2S in the cases. Elevated H_2S contents (up to 32%) in the Triassic Jialingjiang Formation are considered to result from TSR while relatively low H_2S (up to 2000ppm) in the Hetianhe Field resulted from BSR. However, it is not the case for the Central Tarim where relatively low H2S but abundant authigenetic pyrite occurr. Part of the H_2S in the Central Tarim reservoirs has reacted with iron released from clay minerals to precipitate pyrite. Thus, reduced sulphur δ~(34)S and reservoir temperatures rather than the H2S amount are reliable parameters to distinguish between TSR and BSR. TSR in Sichuan Basin Triassic Jialingjiang Formation and Central Tarim Paleozoic reservoirs are showed to take place at more than 125℃. the H2S and authigenetic pyrite have δ~(34)S close to parent anhydrite. In contrast, BSR in the reservoirs near the Carboniferous - Ordovician unconformity in the Hetianhe Field and in the Tertiary in the Jinxian Sag took place at temperatures less than 80℃with sulphide δ~(34)S as light as -24.9‰ and -12.5‰, anhydrite δ~(34)S as heavy as +26‰and +3 5-+40‰, respectively. Chemistry and isotopic composition of the natural gases change as the result of sulphate reduction. It has been observed that relative composition of light hydrocarbon gases is changed along with a rise in H_2S and CO_2. TSR in the Triassic Jialingjiang Formation and BSR in the Hetianhe Field result in a greater degree of preferential depletion of methane than larger molecular hydrocarbon gases. As TSR or BSR proceeds, hydrocarbon gases evolved to heavier carbon isotope as the result of kinetic isotopic fractionation, i.e., selective anaerobic oxidation of ~(12)C. Using the model of residual methane (Whiticar, 1999) to describe the relationship among the proportion of methane oxidation, isotopic shift and fraction factor, about 30% methane is calculated to have been oxidized during BSR in the western part of the Hetianhe Field. From the above, it can be concluded that in the area where H_2S is abundant, empiricalδ~(13)C -Ro relationships do not work. Sulphate reduction results in a rise in sulphur content, gravity and viscosity of an oil as well as changes in δ~(13)C and δ~(34)S. On special conditions, the reduced sulphur from sulphates might be incorporated into oils, i.e., the increasing sulphur is derived from secondarily reduced sulphur. A positive correlative relationship exists between sulphur content and δ~(34)S in the oils in Paleozoic reservoirs in Central Tarim, indicating that enhanced sulphur is ~(34)S-enriched, originated from TSR. The Jinxian oil with the highest sulphur content has the lightest δ~(34)S, suggesting part of the sulphur in the oil is ~(34)S-depleted, originated from BSR. In the Jinxian oil with increasing sulphur content, asphaltenes shows higher content and more negative δ~(13)C, and saturates shows evidence of biodegradetion and a decreasing content and a positive δ~(13)C shift. Thus, asphaltenes have δ~(13)C values closer to saturates. All the above indicate that the reduced sulphur has been incorporated into biodegradated saturates to generate new asphaltenes with relatively light δ~(13)C of saturates. Thiols and thiophenes in natural gases in the Triassic Jialingjiang Formation may result from reaction of H_2S with hydrocarbon. In the Jialingjiang Formation hydrocarbon gases are dominated by methane thus have a high dryness coefficient and thiols are showed to be positively related to H_2S content, suggesting that the thiols may result from H_2S reaction with short chain hydrocarbons. In contrast, high thiophenes occur in wet gases in Jurassic reservoirs with their source rock from sulphur - depleted type I kerogen, indicating that thiophenes may be a product of reaction of H2S with longer chain hydrocarbons.

中强地震震源的破裂过程

With the large developments of the seismic sources theory, computing technologies and survey instruments, we can model and rebuild the rupture process of earthquakes more realistically. On which earthquake sources' properties and tectonic activities law are realized more clearly. The researches in this domain have been done in this paper as follows. Based on the generalized ray method, expressions for displacement on the surface of a half-space due to an arbitrary oriented shear and tensile dislocation are also obtained. Kinematically, fault-normal motion is equivalent to tensile faulting. There is some evidence that such motion occurs in many earthquakes. The expressions for static displacements on the surface of a layered half-space due to static point moment tensor source are given in terms of the generalized reflection and transmission coefficient matrix method. The validity and precision of the new method is illustrated by comparing the consistency of our results with the analytical solution given by Okada's code employing same point source and homogenous half-space model. The computed vertical ground displacement using the moment tensor solution of the Lanchang_Gengma earthquake displays considerable difference with that of a double couple component .The effect of a soft layer at the top of the homogenous half-space on a shallow normal-faulting earthquake is also analyzed. Our results show that more seismic information would be obtained utilizing seismic moment tensor source and layered half-space model. The rupture process of 1999 Chi-Chi, Taiwan, earthquake investigated by using co-seismic surface displacement GPS observations and far field P-wave records. In according to the tectonic analysis and distributions of aftershock, we introduce a three-segment bending fault planes into our model. Both elastic half-space models and layered-earth models to invert the distribution of co-seismic slip along the Chi-Chi earthquake rupture. The results indicate that the shear slip model can not fit horizontal and vertical co-seismic displacements together, unless we add the fault-normal motion (tensile component) in inversions. And then, the Chi Chi earthquake rupture process was obtained by inversion using the seismograms and GPS observations. Fault normal motions determined by inversion, concentrate on the shallow northern bending fault from Fengyuan to Shuangji where the surface earthquake ruptures reveal more complexity and the developed flexural slip folding structures than the other portions of the rupture zone For understanding the perturbation of surface displacements caused by near-surface complex structures, We have taken a numeric test to synthesize and inverse the surface displacements for a pop-up structure that is composed of a main thrust and a back thrust. Our result indicates that the pop-up structure, the typical shallow complex rupture that occurred in the northern bending fault zone form Fengyuan to Shuangji, can be modeled better by a thrust fault added negative tensile component than by a simple thrust fault. We interpret the negative tensile distributions, that concentrate on the shallow northern bending fault from Fengyuan to Shuangji, as a the synthetic effect including the complexities of property and geometry of rupture. The earthquake rupture process also reveal the more spatial and temporal complexities form Fenyuan to SHuangji. According to the three-components teleseismic records, the S-wave velocity structure beneath the 59 teleseismic stations of Taiwan obtained by using the transform function method and the SA techniques. The integrated results, the 3D crustal structure of Taiwan reveal that the thickest part of crustal local in the western Central Range. This conclusion is consistent with the result form the Bouguer gravity anomaly. The orogenic evolution of Taiwan is young period, and the developing foot of Central Range dose not in static balancing. The crustal of Taiwan stays in the course of dynamic equilibrium. The rupture process of 2003)2,24,Jiashi, Xinjiang earthquake was estimated by the finite fault model using far field broadband P wave records of CDSN and IRIS. The results indicate that the earthquake focal is north dip trust fault including some left-lateral strike slip. The focal mechanism of this earthquake is different form that of earthquakes occurred in 1997 and 1998, but similar to that of 1996, Artux, Xinjiang earthquake. We interpreted that the earthquake caused trust fault due to the Tarim basin pushing northward and orogeny of Tianshan mountain. In the end, give a brief of future research subject: Building the Real Time Distribute System for rupture process of Large Earthquakes Based on Internet.

库车坳陷第三纪磁性地层和磁组构的研究

The Tertiary Kuche depression, also known as one of the most economically important oil and gas prospecting regions in the Tarim Basin, is a foreland basin formed by flexural subsidence resulting from the southward thrusting of the southern Tianshan. Detailed geological and geophysical studies on the Tertiary sequence of the Kuche region would provide constraints not only on the Mesozoic and Cenozoic deformation patterns, and its controlling on the formation and distribution of oil and gas of the Kuche depression, but also on the India-Asia postcollisional uplift and continental deformation of the Tianshan regions. In this thesis, the Tertiary sequence of the Kuche depression, which is composed of the upper Kumukeliemu Formation, Suweiyi Formation, Jidike Formation, Kangcun Formation, and Kuche Formation, was selected for magnetostratigraphic and anisotropy of magnetic susceptibility (AMS) study. Among a total of 697 collected sites, 688 sites gave magnetic fabric results and 686 sites yielded reliable paleomagnetic results, building up magenetostratigraphy for the Tertiary sequence of the Kuche depression. By correlating with international geomagnetic polarity timescale, the followings were concluded: 1) the time interval of the sampling sections is some 31-8.1 Ma; 2) the boundaries for Kangcun/Jidike Formations, Jidike/Suweiyi Formations, and Suweiyi/Kumukeliemu Formations are at about 13.5 Ma, 26 Ma and 29 Ma respectively; 3) the Jidike Formation might be formed in an interval between the late Upper Oligocene and middle Miocene, whereas the Suweiyi Formation was formed in the Upper Oligocene, in turn, the Paleogene/Neogene boundary is most likely to be at the bottom of the Jidike Formation in the Kuche depression; 4) the dramatic transition from the marine/lacustrine to fluvial/alluvial facies in the Suweiyi Formation and the lower Jidike Formation of the Kuche depression, which may indicate the initiation of Cenozoic thrusting in the Kuche depression, is probably occurred in the late Oligocene, i.e. at about 28-25 Ma. On the other hand, systematic differences of the AMS parameters, such as the corrected anisotropy of magnetic susceptibility, shape parameter of ellipsoids, q factors, angles between the intermediate and minimum magnetic susceptibility directions and bedding, indicate that a dramatic transition of tectonic strain is most likely to occur at about 16 Ma (middle Miocene) in the Kuche depression. Taking into account the initiation o f C enozoic thrusting in the Kuche d epression i s at about 2 8-25 M a, we argue that the intensive Cenozoic thrusting in the Kuche depression is mainly happened during a period between the late Oligocene to middle Miocene.

塔里木盆地历史时期的自然环境演变

Exploit Tarim Basin Historical Physical Geographic Information System by linking historical documents and Geographic Information System, reconstruct the physical environmental evolution in Tarirn Basin during historical period (the last 2 Ka), special discuss riverhead of the Yellow River and Lop Nur. Based on analyzing Chinese historical documents (antiquity maps and texts), extract physical environmental information in Xiyu during historical period from Twenty-Five History and geographic books and records past dynasties, divide it into 4 period of time. Regarding digital topographical maps as base maps and looking on water bodies, vegetation and desert as central factors, quantify historical physical geographic data in Geographic Information System in terms of dynastic combination of Xianqin-Han, Jin-Wei-Nanbeichao, Tang-Wudai and Song-Yuan-Ming-Qing, execute physical environmental maps of Xiyu through the ages, in order to image the changes of water system, oasis and desert in Xiyu during the last 2 Ka. Compare cross orientation the relation of environmental factors all historical period of time from the influence of climate to oasis and desert, deem that climate condition decided ecological structure in direct and restrict the extent of desertification, especially climate corresponded the style of oasis and the spread of desert in the period of Jin-Wei-Nanbeichao and Tang-Wudai. Compare portrait direction the physical environmental characters in Xiyu during different period of time from 5 aspects of water bodies, oasis, desert, products and climate, deem that physical environment in Xiyu changed in all aspects during historical period. The origin of Lysenkoism about the Yellow River Undercurrent is agelong, whose ascending and descending at times due to investigating the riverhead of the Yellow River time after time during historical period and researching and disputing about the geographic location of Jishishan Mountain. It could consider the faultage in northeastern Qinghai-Xizang Plateau as the channels of undercurrent according to the research of modern geoscience field in the riverhead region.

泥河湾盆地磁性地层学研究——以东谷索和岑家湾剖面为例

The Nihewan Basin is a key area for research into human occupation at high northern latitudes in northeast Asia after the initial expansion of early humans out of Africa. Well-developed late Cenozoic lacustrine deposit sequence in this basin offers a unique opportunity to address this issue. In this thesis, detailed magnetostratigraphic investigation coupled with mineral magnetism was conducted on the Donggutuo and Cenjiawan sections in the eastern basin, where lacustrine deposits sequences containing the Donggutuo, Maliang and Cenjiawan Paleolithic sites are well developed. The sequences are mainly composed of grayish-white clays, grayish-green clayey silts, grayish-yellow silts and fine-grained brown sands, which have recorded reliable polarity variations of geomagnetic field.Characteristics of the anisotropy of magnetic susceptibility show that the sediments have preserved typical original magnetic fabric for sediments, indicating that the strata were developed in a low-energy lake environment and were never perturbed by tectonic stress since deposition. High-temperature magnetic susceptibility measurements (x-T) of representative specimens and demagnetization experiments indicate that the dominant magnetic mineral and remanent carrier at the two sections is magnetite. In addition, hematite and possibly minor maghemite exists in some portions of the sequences. The majority of the samples have relatively simple demagnetization behaviors. After removal of soft magnetic components, the stable characteristic remanent magnetizations (ChRMs) are isolated, which can represent the original remanences.The Donggutuo section mainly records the Brunhes chron, the Matuyama chron and the Jaramillo subchron. The Maliang stone artifact layer occurs just below the Brunhes/Matuyama boundary; and the Donggutuo artifact layer, just below the Jaramillo onset. Accordingly, the Maliang and Donggutuo sites can be dated at about 0.78 Ma and 1.1 Ma, respectively. The Cenjiawan section has recorded a portion of the Matuyama chron. After correlations with the magnetic polarity sequence of the Majuangou section adjacent to this section, the Cenjiawan stone artifact layer is determined below the Jaramillo onset, with an estimated age of 1.1 Ma.To establish the magnetic stratigraphy framework for the lacustrine sediments in the eastern Nihewan Basin, this thesis draws on the magnetic polarity sequences of the Donggutuo and Cenjiawan sections as well as previously obtained results from the Majuangou, Haojiatai, Xiaochangliang and Donggou sections for magnetostratigraphic correlations. The accumulation of the lacustrine sequences at the east margin of the basin commenced from about 2.0 Ma. These sequences record not only the coarse magnetostratigraphy of the Brunhes normal chron and the middle to late Matuyama reverse chron (that is, the Jaramillo and Olduvai subchrons) but also some of the fine structure (that is, the Kamikatsura, Santa Rosa, Punaruu and Cobb Mountain geomagnetic events). The development of the Nihewan paleolake experienced at least twice large expansion periods, split by a large-scale shrinking event in the middle period of the paleolake development. The accumulation of the lacustrine strata was controlled by fault activities.After temporal control for the Donggutuo, Maliang and Cenjiawan Paleolithic sites were established, the three sites along with other well-dated Paleolithic/hominin sites of the Early Pleistocene in North China were combined to construct a chronological sequence of early human occupation in northeastern Asia. Furthermore, after incorporation of paleoclimate changes retrieved from Chinese loess/paleosol sequences and marine sediments, it could be possibly proposed that human groups of the Early Pleistocene in North China might have survived repeated warm/humid interglacials and cold/dry glacials, which were paced by earth orbital variations of the Eastern paleomonsoon.