965 resultados para Sub-surface visualization


Relevância:

80.00% 80.00%

Publicador:

Resumo:

This thesis presents a methodology for measuring thermal properties in situ, with a special focus on obtaining properties of layered stack-ups commonly used in armored vehicle components. The technique involves attaching a thermal source to the surface of a component, measuring the heat flux transferred between the source and the component, and measuring the surface temperature response. The material properties of the component can subsequently be determined from measurement of the transient heat flux and temperature response at the surface alone. Experiments involving multilayered specimens show that the surface temperature response to a sinusoidal heat flux forcing function is also sinusoidal. A frequency domain analysis shows that sinusoidal thermal excitation produces a gain and phase shift behavior typical of linear systems. Additionally, this analysis shows that the material properties of sub-surface layers affect the frequency response function at the surface of a particular stack-up. The methodology involves coupling a thermal simulation tool with an optimization algorithm to determine the material properties from temperature and heat flux measurement data. Use of a sinusoidal forcing function not only provides a mechanism to perform the frequency domain analysis described above, but sinusoids also have the practical benefit of reducing the need for instrumentation of the backside of the component. Heat losses can be minimized by alternately injecting and extracting heat on the front surface, as long as sufficiently high frequencies are used.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The study of the micro-fauna of Montana formations has been almost entirely neglected. Because the petroleum industry of this state has not felt the necessity for using micro-paleontology in its sub-surface correlations, the science has been but little used. The Montana Power Company has had an examination made of some of its well cuttings by a competent micro-paleontologist who found some foraminifera in Mesozoic sediments. However, no investiga­tions have been made to determine the presence and character of the micro-fauna of the Paleozoic formations of Montana.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The correlation of non-fossiliferous drill samples is one of the difficult problems that is en­countered in sub-surface stratigraphy. In order to truly correlate a formation, it must have some dis tinctive features and have an areal persistence of these features. These requirements are probably met best by limestone.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The geologic history of the multi-ringed Argyre impact basin and surroundings has been reconstructed on the basis of geologic mapping and relative-age dating of rock materials and structures. The impact formed a primary basin, rim materials, and a complex basement structural fabric including faults and valleys that are radial and concentric about the primary basin, as well as structurally-controlled local basins. Since its formation, the basin has been a regional catchment for volatiles and sedimentary materials as well as a dominant influence on the flow of surface ice, debris flows, and groundwater through and over its basement structures. The basin is interpreted to have been occupied by lakes, including a possible Mediterranean-sized sea that formed in the aftermath of the Argyre impact event The hypothesized lakes froze and diminished through time, though liquid water may have remained beneath the ice cover and sedimentation may have continued for some time. At its deepest, the main Argyre lake may have taken more than a hundred thousand years to freeze to the bottom even absent any heat source besides the Sun, but with impact-induced hydrothermal heat, geothermal heat flow due to long-lived radioactivities in early martian history, and concentration of solutes in sub-ice brine, liquid water may have persisted beneath thick ice for many millions of years. Existence of an ice-covered sea perhaps was long enough for life to originate and evolve with gradually colder and more hypersaline conditions. The Argyre rock materials, diverse in origin and emplacement mechanisms, have been modified by impact, magmatic, eolian, fluvial, lacustrine, glacial, periglacial, alluvial, colluvial, and tectonic processes. Post-impact adjustment of part of the impact-generated basement structural fabric such as concentric faults is apparent. Distinct basin-stratigraphic units are interpreted to be linked to large-scale geologic activity far from the basin, including growth of the Tharsis magmatic-tectonic complex and the growth into southern middle latitudes of south polar ice sheets. Along with the migration of surface and sub-surface volatiles towards the central part of the primaiy basin, the substantial difference in elevation with respect to the surrounding highlands and Tharsis and the Thaumasia highlands result in the trapping of atmospheric volatiles within the basin in the form of fog and regional or local precipitation, even today. In addition, the impact event caused long-term (millions of years) hydrothermal activity, as well as deep-seated basement structures that have tapped the internal heat of Mars, as conduits, for far greater time, possibly even today. This possibility is raised by the observation of putative open-system pingos and nearby gullies that occur in linear depressions with accompanying systems of faults and fractures. Long-term water and heat energy enrichment, complemented by the interaction of the nutrient-enriched primordial crustal and mantle materials favorable to life excavated to the surface and near-surface environs through the Argyre impact event, has not only resulted in distinct geomorphology, but also makes the Argyre basin a potential site of exceptional astrobiological significance. (C) 2015 Elsevier Inc. All rights reserved.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

En este trabajo se evalúa el comportamiento del nivel freático (NF) en un área de regadío de 75.774 ha ubicadas en el tercio inferior de la cuenca del río Atuel, departamentos de General Alvear y San Rafael en la provincia de Mendoza, y su vinculación con: las pérdidas que se producen en la red de canales, las prácticas de riego y los escurrimientos sub-superficiales de zonas más elevadas. En la zona existe una red de 193 freatímetros en la que se han registrado lecturas de niveles freáticos desde 1980 a 2008, en distintas estaciones del año. El área de estudio se dividió en cuatro sub-zonas, cada una de ellas abastecida por un canal matriz de riego. La serie existente de lecturas de NF permitió elaborar planos estacionales de isohipsas e isobatas medias. Se definieron indicadores de factor de reacción freática (FRF) y de eficiencia del sistema (IES); además, se elaboraron planos de isolíneas y tablas de salinidad (conductividad eléctrica) media del agua subterránea. El análisis de los registros recopilados muestra la dirección del flujo de agua subterránea "noroeste-sureste", isohipsas con un gradiente medio de 1,54 m.Km-1 y nivel freático (NF) con una profundidad mínima media de 1.31 m. La evidencia de zonas de recarga de agua subterránea posibilita, junto a los otros planos, una rápida identificación de zonas vulnerables al ascenso del NF. El FRF permitió establecer que se incorpora al área cultivada de Alvear-Bowen un volumen de 3,7 veces más agua que la requerida por los cultivos y que el IES es del 27%. En primavera, el riego representa el 66% del volumen incorporado a la zona mientras que las precipitaciones representan el 34 % y la superficie con NF de hasta 1,0 m de profundidad es 4,8 veces mayor al promedio del área afectada en las demás estaciones. Los resultados brindan una fuente de información actualizada para la planificación del uso del suelo en la zona, para la operación del sistema de riego y para la implementación y priorización de planes de mejora en la infraestructura.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Vertical fluxes of 239+240Pu and 241Am and temporal changes in their inventories in the northwestern Mediterranean Sea have been examined through high-resolution water column sampling coupled with direct measurements of the vertical flux of particle-bound transuranics using time-series sediment traps. Water column profiles of both radionuclides showed well-defined sub-surface maxima (2391240Pu between 100-400 m; 241Am at 100-200 m and 800 m), the depths of which are a result of the different biogeochemical scavenging behavior of the two radionuclides. Comparison of deep water column (0-2,000 m) transuranic inventories with those derived from earlier measurements demonstrate that the total 2391240Pu inventory had not substantially changed between 1976-1990 whereas 241Am had decreased by approximately 24%. Enhanced scavenging of 241Am and a resultant, more rapid removal from the water column relative to 239+240Pu was also supported by the observation of elevated Am/Pu activity ratios in sinking particles collected in sediment traps at depth. Direct measurements of the downward flux of particulate 239+240Pu and 241Am compared with transuranic removal rates derived from observed total water column inventory differences over time, show that particles sinking out of deep waters (1,000-2,000 m) could account for 26-72% of the computed total annual 239+240Pu loss and virtually all of the 241Am removal from the water column. Upper water column (0-200 m) residence times based on direct flux measurements ranged from 20-30 yr for 239+240Pu and 5-10 yr for 241Am. The observation that 241Am/239+240Pu activity ratios in unfiltered Mediterranean seawater are six times lower than those in the north Pacific suggests the existence of a specific mechanism for enhanced scavenging and removal of 241Am from the generally oligotrophic waters of the open Mediterranean. It is proposed that atmospheric inputs of aluminosilicate particles transported by Saharan dust events which frequently occur in the Mediterranean region could enhance the geochemical scavenging and resultant removal of 241Am to the sediments.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Structure and composition of sub-surface bottom sediments from the southwest Barents Sea have been under study. The study has revealed heterogeneity of sediment structure resulted from temporal irregularity and variability of sedimentation processes. The study of the heavy minerals from 0.1-0.01 mm grain size fraction has shown prevalence of green hornblende, epidote, garnet, and ilmenite in all types of sediments; these minerals are the basis of terrigenous-mineralogical province. At the same time in different areas local terrigenous-mineralogical associations have been identified. Clay mineral composition of in the sediments was quite uniform: biotite, chlorite, hydromica, smectite. Despite this, a number of features indicating initial stages of clay mineral transformation has been identified. Differences in material composition and structure of the studied sediments are associated with rapid change in paleogeographic situation on the land - ice cover melting on the Kola Peninsula and subsequent Holocene climatic situation.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Structure and composition of sub-surface bottom sediments from the southwest Barents Sea have been under study. The study has revealed heterogeneity of sediment structure resulted from temporal irregularity and variability of sedimentation processes. The study of the heavy minerals from 0.1-0.01 mm grain size fraction has shown prevalence of green hornblende, epidote, garnet, and ilmenite in all types of sediments; these minerals are the basis of terrigenous-mineralogical province. At the same time in different areas local terrigenous-mineralogical associations have been identified. Clay mineral composition of in the sediments was quite uniform: biotite, chlorite, hydromica, smectite. Despite this, a number of features indicating initial stages of clay mineral transformation has been identified. Differences in material composition and structure of the studied sediments are associated with rapid change in paleogeographic situation on the land - ice cover melting on the Kola Peninsula and subsequent Holocene climatic situation.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Fifteen Iberian margin sediment cores, distributed between 43°12'N and 35°53'N, have been used to reconstruct spatial and temporal (sub)surface circulation along the Iberian margin since the Last Glacial period. Time-slice maps of planktonic foraminiferal derived summer sea surface temperature (SST) and export productivity (Pexp) were established for specific time intervals within the last 35 ky: the Holocene (Recent and last 8 ky), Younger Dryas (YD), Heinrich Stadials (HS) 1, 2a, 2b, 3, and the Last Glacial Maximum (LGM). The SST during the Holocene shows the same latitudinal gradient along the western Iberian margin as present-day with cold but productive areas that reflect the influence of coastal upwelling centers. The LGM appears as a slightly less warm, but more productive period relative to the Holocene and present-day conditions, suggesting that sea-level minima forced a westward displacement of the coastal upwelling centers possibly accompanied by a strengthening of northward winds. During the YD, a longitudinal thermal front is depicted at 10°W, with cold polar waters offshore and warmer subtropical waters inshore, suggesting that the subtropical Paleo-Iberian Poleward Current more likely flowed at a more inshore location masking the local SST signal and amplitude of variation. A substantial cooling and drop in productivity is observed during all HS, in particular HS1 and HS3, reflecting the penetration of icebergs-derived meltwater. These most extreme southward extensions of very cold waters define a strong SST gradient that marks a possible Paleo-Azores Front. Higher production south of this front was likely fed by frontal nutrient advection.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The Weddell Gyre plays a crucial role in the regulation of climate by transferring heat into the deep ocean through deep and bottom water mass formation. However, our understanding of Weddell Gyre water mass properties is limited to regions of data availability, primarily along the Prime Meridian. The aim is to provide a dataset of the upper water column properties of the entire Weddell Gyre. Objective mapping was applied to Argo float data in order to produce spatially gridded, time composite maps of temperature and salinity for fixed pressure levels ranging from 50 to 2000 dbar, as well as temperature, salinity and pressure at the level of the sub-surface temperature maximum. While the data are currently too limited to incorporate time into the gridded structure, the data are extensive enough to produce maps of the entire region across three time composite periods (2002-2005, 2006-2009 and 2010-2013), which can be used to determine how representative conclusions drawn from data collected along general RV transect lines are on a gyre scale perspective. The time composite data sets are provided as netCDF files; one for each time period. Mapped fields of conservative temperature, absolute salinity and potential density are provided for 41 vertical pressure levels. The above variables as well as pressure are provided at the level of the sub-surface temperature maximum. Corresponding mapping errors are also included in the netCDF files. Further details are provided in the global attributes, such as the unit variables and structure of the corresponding data array (i.e. latitude x longitude x vertical pressure level). In addition, all files ending in "_potTpSal" provide mapped fields of potential temperature and practical salinity.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Porous seep-carbonates are exposed at mud volcanoes in the eastern Mediterranean Sea. The 13C-depleted aragonitic carbonates formed as a consequence of the anaerobic oxidation of methane in a shallow sub-surface environment. Besides the macroscopically visible cavernous fabric, extensive carbonate corrosion was revealed by detailed analysis. After erosion of the background sediments, the carbonates became exposed to oxygenated bottom waters that are periodically influenced by the release of methane and upward diffusion of hydrogen sulphide. We suggest that carbonate corrosion resulted from acidity locally produced by aerobic oxidation of methane and hydrogen sulphide in the otherwise, with respect to aragonite, oversaturated bottom waters. Although it remains to be tested whether the mechanisms of carbonate dissolution suggested herein are valid, this study reveals that a better estimate of the significance of corrosion is required to assess the amount of methane-derived carbon that is permanently fixed in seep-carbonates.