Voltammetric sensing of the fuel dye marker Solvent Blue 14 by screen-printed electrodes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of a pilot washing system on dicofol levels in orange matrix

An efficient analytical method is described for the analysis of dicofol residues in pulp and orange peel. Samples are mixed with Celite and transferred to chromatographic columns prepacked with silica gel. Dicofol is eluted with ethyl acetate, and the extracts are analyzed by gas chromatography with electron capture detection. Mean recoveries for dicofol at levels of 0.5, 2.0, 5.0, and 10 mg/kg ranged from 87 to 95% with relative standard deviation values between 2.6 and 9.0%. To investigate the effect of a pilot washing system on dicofol residues in oranges, the analytical procedure was applied to samples submitted to different treatments with commercial formulations under field and laboratory conditions. The orange samples with and without washing were analyzed in duplicate, and the results indicated that washing under the described conditions did not allow a complete removal of dicofol residues from orange peel.

Determination of the vinylsulphone azo dye, remazol brilliant orange 3R, by cathodic stripping voltammetry

Remazol brilliant orange 3R shows only a voltammetric peak for the reduction of the azo group. No peak was observed for the reduction of the sulfatoethylsulfone or vinylsulfone reactive groups. The reduction of a pre-protonated ate group involving a two-electron process, gives a hydrate derivative in acidic solution. In alkaline solution the reduction process occurs at more negative potential with the formation of an unstable hydrate compound which decomposes via HN-NH bond cleavage and loss of a sulfate group. Optimum conditions are given for the cathodic stripping voltammetric determination of dir: dye in aqueous solution. The optimum accumulation potential and time were 0 V and up to 60 s, respectively. Linear calibration graphs were obtained from 30 to 300 ng ml(-1) in pH 4 and 6.2 to 62 ng ml(-1) in pH 10. The limit of determination obtained was 1.5 ng ml(-1) (pH 10). The coefficient of variation was 2.6% (n = 7) at 62 ng ml(-1) of the reactive dye. (C) 1999 Elsevier B.V. B.V. All rights reserved.

Square-wave voltammetry applied to the analysis of the dye marker, solvent blue 14, in kerosene and fuel alcohol

The purpose of this paper is to develop an electroanalytical method based on square-wave voltammetry (SWV) for the determination of the solvent blue 14 (SB-14) in fuel samples. The electrochemical reduction of SB-14 at glassy carbon electrode in a mixture of Britton-Robinson buffer with N,N-dimethyiformamide (1:1, v/v) presented a well-defined peak at-0.40 V vs. Ag/AgCl. All parameters of the SWV technique were optimized and the electroanalytical method presented a linear response from 1.0 x 10(-6) to 6.0 x 10(-6) mol L-1 (r = 0.998) with a detection limit of 2.90 x 10(-7) mol L-1. The developed method was successfully utilized in the quantification of the dye SB-14 in kerosene and alcohol samples with average recovery from 93.00 to 98.10%.

Pectin lyase from Aspergillus giganteus: Comparative study of productivity of submerged fermentation on citrus pectin and orange waste

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fruit maturation as a parameter for selection of sweet orange cultivars in Brazil

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Kinetics of the reaction of alkylamines with 7,7,8,8-tetracyanoquinodimethane (TCNQ) in organic solvents

The following sequence of substitution reactions was studied spectrophotometrically in organic solvents: RNH2 + TCNQ →-HCN 7-substituted TCNQ →-HCN +RNH2 7.7-disubstituted TCNQ where R = butyl, octyl, dodecyl, and hexadecyl. The production of 7-(alkylamino)-7,7,8-tricyanoquinodimethanes proceeds via the formation of the anion radical of TCNQ (TCNQ-·) whose rate of appearance was found to be a function of the chain length of R, reaching a maximum for octylamine. The formation of TCNQ-· was sensitive to the solvent polarity and electron-donor power and was associated with a small enthalpy and a highly negative entropy of activation. Above a certain [C8H17NH2] the rate of disappearance of TCNQ-· was independent of the amine concentration, and the reaction had a much higher enthalpy and entropy of activation. The occurrence of tautomerism precluded an investigation of the conversion of 7-(octylamino)-7,8,8-tricyanoquinodimethane into 7,7-bis(octylamino)-8,8-dicyanoquinodimethane. A study of the reaction of octylamine with 7-morpholino-7,8,8-tricyanoquinodimethane (which does not exist in tautomeric forms) showed that the second substitution step proceeds with the same mechanism as the first one. The only difference between the two compounds (TCNQ and its monosubstituted morpholino derivative) is one of reactivity. © 1985 American Chemical Society.

Sensory profile and preference mapping of orange cakes with addition of prebiotics inulin and oligofructose

Orange cakes with addition of inulin and oligofructose to justify a prebiotic claim (minimum of 3 g of fructans in a 60 g serving of cake) were investigated regarding sensory aspects. The sensory profile of cakes with inulin, with inulin/oligofructose and without prebiotics (standard cake) was evaluated using descriptive quantitative analysis. Preference mapping was assessed using multidimensional scaling on data obtained through an acceptability test with a nine-point hedonic scale. The cakes with prebiotics presented greater crust brownness, dough beigeness, hardness and stickiness than the standard cake and lower crumbliness. Principal Component Analysis (69.5 and 10.7% of explanation to the first and second principal components, respectively) showed that crust brownness, dough beigeness, hardness and stickiness contributed to distinguish the cakes with prebiotics from standard cakes. The sensory acceptability was similar for the three cakes and higher when compared to three commercial cakes, but the preference mapping showed that cakes with prebiotics were preferred to commercial cakes. Addition of prebiotics in orange cakes is feasible, based on the sensory results, which may facilitate marketing of this functional food with sensorial qualities equivalent to conventional products. © 2012 Elsevier Ltd.

Characterization of a glucose- and solvent-tolerant extracellular tannase from Aspergillus phoenicis

Tannases have attracted wider attention because of their biotechnological potential, especially enzymes from filamentous fungi and other microorganisms. However, the biodiversity of these microorganisms has been poorly explored, and few strains were identified for tannase production and characterization. This article describes the production, purification and characterization of a glucose- and solvent-tolerant extracellular tannase from Aspergillus phoenicis. High enzymatic levels were obtained in Khanna medium containing tannic acid up to 72 h at 30 °C under 100 rpm. The purified enzyme with 65% of carbohydrate content had an apparent native molecular mass of 218 kDa with subunits of 120 kDa and 93 kDa and was stable at 50 °C for 1 h. Optima of temperature and pH were 60 °C and 5.0-6.5, respectively. The enzyme was not affected significantly by most ions, detergents and organic solvents. While glucose did not affect the tannase activity, the addition of a high concentration of gallic acid did. The Km values were 1.7 mM (tannic acid), 14.3 mM (methyl-gallate) and 0.6 mM (propyl-gallate). The enzyme was able to catalyze the transesterification reaction to produce propyl-gallate. All biochemical properties suggest the biotechnological potential of the glucose- and solvent-tolerant tannase from A. phoenicis. © 2012 Elsevier B.V. All rights reserved.

Effects of dentin dry/moist condition on the immediate adhesive performance of different solvent-based etch-and-rinse adhesivesystems

Purpose: The purpose of this research was to analyze and measure, under optical microscopy, the hybrid layer thickness and resin tags length, as well as the microtensile bond strength of two conventional adhesive systems when applied to dry and moist dentinal substrate. Methods: Thirty-two extracted human molars were randomly distributed into four groups according to the adhesive systems (XP Bond and Prime&Bond 2.1) and moisture condition (dry and moist). In Groups I and II, XP adhesive system was applied on dry and moist dentin, respectively; while Groups III and IV received PB adhesive system, in the same way as was done in Groups I and II, respectively. After adhesive and restorative procedures, all specimens were sectioned along their long axes; one hemi-tooth sample was subjected to the microtensile bond strength test while the other was decalcified and serially sectioned into six micron thick slices and sequentially mounted on glass slides. These sections were stained by the Brown and Brenn method for posterior analysis and measurement of the hybrid layer and resin tags under a light microscope with a micrometric ocular 40/075. Results: Data were analyzed using two-way ANOVA and Tukey's test (α=0.05). For the variable hybrid layer thickness, XP showed no significant differences between dry and moist dentin (5.2 μm and 5.5 μm, respectively), but for PB, hybrid layer was significantly thicker for moist (4.0 μm) than for dry dentin (3.0 μm). For the variable resin tags length XP showed 17.9 μm length for dry dentin and 20.8 μm for moist dentin; PB 11.7 μm for dry and 12.69 μm for moist dentin;there was no significant differences between them, independent of the moisture condition. For the variable microtensile bond strength, XP showed 38.0 MPa for dry dentin and 44.5 MPa for moist dentin; and PB showed 22.7 MPa for dry dentin and 20.8 MPa for dry dentin no significant difference was observed between moist and dry dentin for XP (p=0.2) and PB (p=0.7), but XP was presented significantly higher bond strength values than PB in both moisture conditions (p=0.003 for dry and p=0.002 for moist). Conclusion: The two-step butanol-based etch-and-rinse adhesive XP Bond presented a superior behavior with regard to the hybrid layer thickness, length of resin tags and bond strength to dry and moist dentin substrates when compared with two-step acetone-based adhesive system Prime&Bond2.1. © 2013 Elsevier Ltd.

Optimisation of High Hydrostatic Pressure Processing of Pêra Rio Orange Juice

The influence of high hydrostatic pressure (HHP) on Pêra Rio orange juice was investigated using response surface methodology. A central composite design was used to evaluate the effects of three processing conditions (independent variables), namely pressure (100-600 MPa), temperature (30-60 °C) and time (30-360 s), on the native microflora and pectin methylesterase (PME) activity of orange juice. Analysis of variance showed that second-order polynomial models fitted well with the experimental data for PME residual activity (R2 = 0.9586, p < 0.001) and aerobic microorganism count (R2 = 0.9879, p < 0.001). The optimum HHP processing conditions to produce orange juice with PME residual activity of less than 20 % and low microorganism count (<2 log cycles CFU/mL) were 550 to 600 MPa, 55 to 60 °C and 330 to 360 s. © 2013 Springer Science+Business Media New York.

Estudos das propriedades estruturais de análogos substituídos com 'TRP POT.2,7 ou 24' do fragmento com 30 resíduos da região amino-terminal da Esticolisina II

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Investigação da dinâmica sequêncial Monte Carlo/Mecânica Quântica para sitemas moleculares orgânicos

O principal objetivo deste trabalho é investigar teóricamente as propriedades eletrônicas e óticas de compostos orgânicos em ambiente líquido. A compreensão das interações em sistemas líquidos é muito importante para a descrição de fenômenos em muitas partes da ciência, como Física, Química, Biologia e Materiais, bem como no desenvolvimento de materiais óticos. As flutuações térmicas fazem que inumaram das configurações para os líquidos possam ser gerados. Esta é a razão do comportamento estatístico observado em sistemas líquidos. Considerando estas dificuldades, o tratamento sequencial Monte Carlo / Mecânica Quântica (SMC/QM) é usado neste trabalho. Neste procedimento, a estrutura líquida é gerada primeiramente por simulações clássicas de MC e mais tarde, somente a parte mais importante do sistema é tratada com mecânica quântica. Usando o procedimento acima, os propriedades do quantum o pirazine dimethyl do thiene Methyl da laranja (MO) e do O 2,3-dimetil tieno[3,4-b] pirazina (DTP) foram investigados. O MO é um conhecido indicador de pH e pode ser encontrado sob circunstâncias básicas e acidas. Suas geometrias de mínima energia foram obtidas mediante a Teoria do Funcional da Densidade pelo funcional B3LYP, sendo o sistema descrito pelas bases de Pople com uma função de polarização (6-31G*). Para obter as propriedades médias dos observaveis, cálculos de química quântica foram executados dentro da aproximação semi-empírica de INDO/S-CI. Com respeito ao espectro de absorção, os dados experimentais existentes na literatura científica reportam a existência de uma larga banda localizada na região de baixas energias, mais precisamente entre 400 e 600 nm. Nossos resultados teóricos para a forma alcalina mostram uma transição intensa transição π → π* aproximadamente à 432.4 ± 0.03 nm e, sob condições ácidas, esta transição aparece aproximadamente à 507.4 ± 0.12, 496.4 ± 0.28 ou 545.3 ± 0.10 nm, dependendo da estrutura, mostrando bom acordo com resultados experimentais. O DTP é um sistema particular usado na produção de polímeros de baixo gap. Suas propriedades elétricas e óticas foram obtidas através de um novo procedimento conhecido por Configuração Eletrostática Média do Solvent (ASEC). O procedimento ASEC inclui moléculas do solvente como cargas pontuais e permite o obtenção das quantidades quânticas executando somente poucos cálculos de mecânica quântica. Para o DTP, usando a teoria das perturbações de segunda ordem Mφller-Plesset (MP2) e o conjunto de bases aug-cc-pVDZ, a convergência do momento de dipolo foi alcançada com apenas quatro cálculos de mecânica quântica à 1.16 D, apresentando um aumento de 42% quando comparado ao dipolo isolado. O polarizabilidade corresponde à outra característica elétrica que pôde ser medida. Considerando o mesmo nível empregado ao cálculo do dipolo, o valor médio 132.7 a30 foi observado. A região de mais baixas da energias do espectro de absorption foi investigada também atravé de procedimento de ASEC usando ambos as aproximações, semi-empírico e DFT. Esta região de absorção é motivo de conclusões contraditórias com relação à natureza das transições n → π* e π → π*. Nossos resultados mostram que realmente que essas excitações são realmente observadas simultanemente podendo sobrepôr-se. Como exemplo, nossos resultados para DFT, encontrados usando o funcional B3LYP nos mostra que estas transições aparecem aproximadamente à 360.6 e 351.1 nm.

Obtaining lipases from byproducts of orange juice processing

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effectiveness of ProTaper retreatment system associated with organic solvents in the removal of root canal filling material

Aim: To evaluate the effectiveness of ProTaper universal retreatment system in the removal of root canal filling material with thermomechanical compaction, in comparison to manualmechanical technique, associated with orange oil or eucalyptol. Materials and methods: Forty extracted lower incisors were filled with thermomechanical compaction technique. After 3 years, the root canal filling was removed by: G1 - manualmechanical technique with orange oil; G2 - manual-mechanical technique with eucalyptol; G3 - ProTaper universal retreatment system with orange oil and G4 - ProTaper universal retreatment system with eucalyptol. In sequence, all root canals were instrumented to F5 instrument. The teeth were longitudinally grooved, images of buccal half were obtained in stereomicroscope and covered area by root canal filling material was measured using image tool software, in cervical, middle and apical radicular thirds. The results were subjected ANOVA and Tukey test (p = 0.05). Results: In all thirds, the manual-mechanical technique showed lower presence of root canal filling material on root canal dentin in comparison to ProTaper retreatment universal system, regardless of organic solvent used (p < 0.05). There is no difference between organic solvents in removal root canal filling material (p > 0.05). Conclusion: The ProTaper universal retreatment system showed lower effectiveness in removal root canal filling material than manual-mechanical technique, regardless of organic solvents (orange oil or eucalyptol oil) used. Clinical significance: Recently rotary instruments have been proposed to removal of root canal filling material. However, there are no studies evaluating its effectiveness in removal root canal filling material in association with orange oil or eucalyptol oil.