Biogenic and mineral composition and foraminiferal stratigraphy of sediment cores obtained in northern Germany

The Ratekau boring ended in clays of the so-called Asterigerina-Zone; these clays have shallow-water features in the uppermost samples. The clays are overlain by deep-water clays with pteropods; this formation is split into two parts by a shallow-water deposit. The fossiliferous series ends upward in sandy deposits with shallow-water fossils. The question is raised whether the two deep-water deposits might correspond to the Lower Doberg Beds (Eochattian) and the Upper Doberg Beds (Neochattian) at the Doberg hill, closer to the rim of the basin. All fossiliferous samples from this boring are thought to be of Late Oligocene age; the boundary towards the Middle Oligocene, however, could not be ascertained. The Vaale boring ended in rather typical Septaria clay of the Middle Oligocene. This clay is capped by some metres of unfossiliferous glauconite clays, which in turn are overlain by silts and silty clays with planktonic fossils identical to those found at Dingden locality. These deposits are tentatively dated as Early Miocene. The next higher series of samples consists of sands and clays deposited in shallower waters. They contain a rich fauna of benthic molluscs, which, according to the current notion in stratigraphy, would have a Reinbek Age. In addition, they contain a set of planktonic fossils which differs from the 'Lower Miocene' assemblages. These sands and clays are overlain by a thick series of marine sands very poor in fossils. Finally, four metres of clay with foraminifera, having Younger Miocene affinities, form the top of the fossiliferous sequence. The borings at Wulksfelde and Langenhorn were not far apart and their sediments are easily correlated. Both wells start below in continental 'Lignite Sands' and contain overlying shallow water sands and clays. These yielded Hemmoor benthic mollusca, supposed to indicate Lower Miocene in the relevant literature; however, we encountered their planktonic foraminifera in the uppermost Miocene as well. The same planktonic species were found in all samples of both borings. These deposits under discussion furthermore contain a particular pteropod species. They are overlain by a thick series of gypsiferous clays, with scarce fossils. The uppermost fossiliferous clays (probably Langenfelde Age) contain another pteropod species, not met with in other samples. The discrepancies between the plankton zonation and the traditional subdivision according to benthic molluscs in the borings of Vaale, Wulksfelde and Langenhorn (and in samples from Twistringen, Dingden and Antwerp localities as well) renders the time-stratigraphic value of the denominations Reinbek and Hemmoor rather doubtful. The samples of the Westerland boring can be placed in the Gram and Sylt stages of local chronostratigraphy on the strength of the Astarte series established by HINSCH. The Gram samples contain a typical pteropod species; both groups of samples contain the same planktonic foraminifera as the borings Wulksfelde and Langenhorn. Our material did not bring the problem of the Miocene-Pliocene boundary in this region any closer to a solution. In conclusion, it can be claimed that this investigation provides strong arguments that the usual recognition of Hemmoor and Reinbek does not correspond to well-defined chronostratigraphical units. A better chronostratigraphic subdivision has to be based on the examination of many more samples, and on a better understanding of the paleoecology of the fossils involved.

Composition of bottom sediments and their exchange with seawater in the Amur and Zolotoy Rog bays, Sea of Japan

Transition of Zn, Cu, Cd, and Pb into solution is studied for experimental suspensions of coastal marine sediments with different degrees of pollution from the Amur Bay (Sea of Japan) over 30-70 days. Concentrations of dissolved metals were measured by a voltammetry method. Transition of Zn and Cd into solution was shown to be linearly dependent on initial pollution of sediments with these metals. Cadmium mobilization is due to gradual degradation of organic matter from sediments. Under degradation processes Zn quickly goes into solution during sedimentation and from silts, while in case of polluted sediments it is slowly mobilized during oxidation of sulfides. Behavior of Cu is complex because of binding of mobilized metal by dissolved organic compounds. Transition of lead into solution is negligible. Calculation of potential transition of metals from sediments into water on the basis of experimental data and its comparison with downward sedimentary flux showed that in the studied area secondary pollution of water by aerobic degradation of sediments is possible only for Cd.

Chemical composition of hydrothermal deposits and vulcanites from the Menez Gwen vent field, Mid-Atlantic Ridge

Surface hydrothermal deposits of the shallow-water Menez Gwen vent field located in the rift zone of the Mid-Atlantic Ridge are mostly composed of nonmetalliferous minerals in contrast to sulfide deposits of deep-water fields. Here sulfide minerals occur only in dispersed form. High-temperature sulfide deposits strongly enriched in copper and zinc occur only immediately below the surface of the bottom. This is related to subsurface boiling and phase separation of initial high-temperature hydrothermal ore-bearing solution that ascends from the interior to the floor surface.

Isotopic ratios and geochemical composition of ODP Hole 176-735B minerals

The mineralogy and stable (O and C) and Sr isotopic compositions of low-temperature alteration phases were determined in Hole 735B gabbroic rocks in order to understand the processes of low-temperature alteration in this uplifted block of lower oceanic crust. Phyllosilicates include smectite (saponite, Mg montmorillonite, and nontronite), chlorite/smectite, chlorite, talc, and serpentine. Other phases include prehnite, albite, K-feldspar, analcite, natrolite, thompsonite, pyrite, and titanite. The low-grade mineral assemblages mainly represent zeolite facies and lower-temperature "seafloor weathering" processes. Phyllosilicates formed over a range of temperatures but may also reflect variable reaction progress. Alteration temperatures were probably somewhat greater below 1300 meters below seafloor. Mineralogy and isotopic data indicate that conditions were mostly reducing and that seawater solutions were rock dominated. Carbonates formed late from cold and generally oxidizing seawater solution, however, as seawater penetrated downward as the result of fracturing and faulting in the uppermost portion of the uplifted crustal block.

Chemical composition of interstitial solutions from sediments of DSDP Legs 6-8, 11, 12, 14, 15, and 22

Through the Deep Sea Drilling Project samples of interstitial solutions of deeply buried marine sediments throughout the World Ocean have been obtained and analyzed. The studies have shown that in all but the most slowly deposited sediments pore fluids exhibit changes in composition upon burial. These changes can be grouped into a few consistent patterns that facilitate identification of the diagenetic reactions occurring in the sediments. Pelagic clays and slowly deposited (<1 cm/1000 yr) biogenic sediments are the only types that exhibit little evidence of reaction in the pore waters. In most biogenic sediments sea water undergoes considerable alteration. In sediments deposited at rates up to a few cm/1000 yr the changes chiefly involve gains of Ca(2+) and Sr(2+) and losses of Mg(2+) which balance the Ca(2+) enrichment. The Ca-Mg substitution may often reach 30 mM/kg while Sr(2+) may be enriched 15-fold over sea water. These changes reflect recrystallization of biogenic calcite and the substitution of Mg(2+) for Ca(2+) during this reaction. The Ca-Mg-carbonate formed is most likely a dolomitic phase. A related but more complex pattern is found in carbonate sediments deposited at somewhat greater rates. Ca(2+) and Sr(2+) enrichment is again characteristic, but Mg(2+) losses exceed Ca(2+) gains with the excess being balanced by SO4(post staggered 2-) losses. The data indicate that the reactions are similar to those noted above, except that the Ca(2+) released is not kept in solution but is precipitated by the HCO3(post staggered -) produced in SO4(post staggered 2-) reduction. In both these types of pore waters Na(+) is usually conservative, but K(+) depletions are frequent. In several partly consolidated sediment sections approaching igneous basement contact, very marked interstitial calcium enrichment has been found (to 5.5 g/kg). These phenomena are marked by pronounced depletion in Na(+), Si and CO2, and slight enhancement in Cl(-). The changes are attributed to exchange of Na(+) for Ca(2+) in silicate minerals forming from submarine weathering of igneous rocks such as basalts. Water is also consumed in these reactions, accounting for minor increases in total interstitial salinity. Terrigenous, organic-rich sediments deposited rapidly along continental margins also exhibit significant evidences of alteration. Microbial reactions involving organic matter lead to complete removal of SO4(post staggered 2-), strong HCO3(post staggered -) enrichment, formation of NH4(post staggered +), and methane synthesis from H2 and CO2 once SO4(post staggered 2-) is eliminated. K+ and often Na+ (slightly) are depleted in the interstitial waters. Ca(2+) depletion may occur owing to precipitation of CaCO3. In most cases interstitial Cl- remains relatively constant, but increases are noted over evaporitic strata, and decreases in interstitial Cl- are observed in some sediments adjacent to continents.

Composition of Fe-Mn nodules and crusts from the Southwest Pacific

A study of samples dredged within areas of tectonic arc-trench systems (Kermadec and New Hebrides) allows to distinguish three types of ferromanganese mineralization. Relationship between mineral and geochemical specialization is established. A conclusion is made that ferromanganese mineralization is a permanent genetic series of matter supply: from endogenic (hydrothermal solution is a dominant source at deposition of chemical elements from mixture seawater plus hydrothermal solutions) to hydrogenic (seawater is a dominant source at element deposition). This results in geochemical and mineralogical variety of ferromanganese mineralization within this part of the Pacific Ocean.

Vertical variations in basic salt composition of interstitial waters from Pacific sediments

Basic chemical composition of interstitial water in sediments of the Northwestern Pacific along a profile from the continental shelf of the Japan Trench to the ocean bed is discussed. Transformation of interstitial water in sediments rich in organic matter on the continental shelf and at the bottom of the Japan Trench is indicated. Variation in the vertical direction of elementary constituents of interstitial salt solution and variations in certain biogenic elements permit to make conclusions concerning processes taking place in sediments during sedimentation and diagenesis. These processes cause both metamorphism of water and transformation of organic and mineral content of sediments.

Microbial community composition in fresh water at different stations

Fluorescence in situ hybridization (FISH) with rRNA-targeted oligonucleotide probes was used to investigate the phylogenetic composition of bacterioplankton communities in several freshwater and marine samples. An average of about 50% of the cells were detected by probes for the domains Bacteria and Archaea. Cells were concentrated from water samples (1 to 100 ml) on white polycarbonate filters (diameter, 47 mm; pore size, 0.2 mm; type GTTP 4700 [Millipore, Eschborn, Germany]) by applying a vacuum of <25 kPa. They were subsequently fixed by covering the filter with 3 ml of a freshly prepared, phosphate-buffered saline (pH 7.2)-4% paraformaldehyde (Sigma, Deisenhofen, Germany) solution for 30 min at room temperature. Airdried filters are ready for hybridization and can be stored at 220°C or room temperature for several months without showing apparent changes. Probes BET42a, GAM42a, and PLA886 were used with competitor oligonucleotides as described previously amongst others in Manz et al., (1992; doi:10.1016/S0723-2020(11)80121-9). The filters were transferred to a vial containing 50 ml of prewarmed (48°C) washing solution (70 mM NaCl, 20 mM Tris-HCl [pH 7.4], 5 mM EDTA, 0.01% sodium dodecyl sulfate) and incubated freely floating without shaking at 48°C for 15 min. The filter sections were dried on Whatman 3M paper (Whatman Ltd., Maidstone, United Kingdom) and covered with 50 ml of DAPI solution (1 mg/ml in distilled water filtered through at 0.2-mm filter) for 5 min at room temperature in the dark. For each sample and probe, more than 500 cells were enumerated; for the DAPI examination, more than 1,500 cells were counted per sample. All probe-specific cell counts are presented as the percentage of cells visualized by DAPI. The mean abundances and standard deviations were calculated from the counts of 10 to 20 randomly chosen fields on each filter section. All counts were corrected by subtracting the counts obtained with the negative control NON338. Mean and standard deviation were calculated from the counts of 10 to 20 randomly chosen fields on each filter section.

(Table 6) Selenium isotopic composition of sediment samples from ODP Site 185-1149

Multiple-collector inductively coupled plasma mass spectrometry has been used for the precise measurement of the isotopic composition of Se in geological samples. Se is chemically purified before analysis by using cotton impregnated with thioglycollic acid. This preconcentration step is required for the removal of matrix-interfering elements for hydride generation, such as transitional metals, and also for the quantitative separation of other hydride-forming elements, such as Ge, Sb, and As. The analyte is introduced in the plasma torch with a continuous-flow hydride generation system. Instrumental mass fractionation is corrected with a "standard-sample bracketing" approach. By use of this new technique, the minimum Se required per analysis is lowered to 10 ng, which is one order of magnitude less than the amount needed for the N-TIMS technique. The estimated external precision calculated for the 82Se/76Se isotope ratio is 0.25? (2 sigma), and the data are reported as delta notation (?) relative to our internal standard (MERCK elemental standard solution). Measurements of Se isotopes are presented for samples of standard solutions and geological reference materials, such as silicate rocks, soils, and sediments. The Se isotopic composition of selected terrestrial and extraterrestrial materials are also presented. An overall Se isotope variation of 8? has been observed, suggesting that Se isotopes fractionate readily and are extremely useful tracers of natural processes.

Supporting End-User Development through a New Composition Model: An Empirical Study

End-user development (EUD) is much hyped, and its impact has outstripped even the most optimistic forecasts. Even so, the vision of end users programming their own solutions has not yet materialized. This will continue to be so unless we in both industry and the research community set ourselves the ambitious challenge of devising end to end an end-user application development model for developing a new age of EUD tools. We have embarked on this venture, and this paper presents the main insights and outcomes of our research and development efforts as part of a number of successful EU research projects. Our proposal not only aims to reshape software engineering to meet the needs of EUD but also to refashion its components as solution building blocks instead of programs and software developments. This way, end users will really be empowered to build solutions based on artefacts akin to their expertise and understanding of ideal solutions

A dynamic programming approach to the formulation and solution of finite element equations

A method for formulating and algorithmically solving the equations of finite element problems is presented. The method starts with a parametric partition of the domain in juxtaposed strips that permits sweeping the whole region by a sequential addition (or removal) of adjacent strips. The solution of the difference equations constructed over that grid proceeds along with the addition removal of strips in a manner resembling the transfer matrix approach, except that different rules of composition that lead to numerically stable algorithms are used for the stiffness matrices of the strips. Dynamic programming and invariant imbedding ideas underlie the construction of such rules of composition. Among other features of interest, the present methodology provides to some extent the analyst's control over the type and quantity of data to be computed. In particular, the one-sweep method presented in Section 9, with no apparent counterpart in standard methods, appears to be very efficient insofar as time and storage is concerned. The paper ends with the presentation of a numerical example

Modulation of the Silica Sol–Gel Composition for the Promotion of Direct Electron Transfer to Encapsulated Cytochrome c

The direct electron transfer between indium–tin oxide electrodes (ITO) and cytochrome c encapsulated in different sol–gel silica networks was studied. Cyt c@silica modified electrodes were synthesized by a two-step encapsulation method mixing a phosphate buffer solution with dissolved cytochrome c and a silica sol prepared by the alcohol-free sol–gel route. These modified electrodes were characterized by cyclic voltammetry, UV–vis spectroscopy, and in situ UV–vis spectroelectrochemistry. The electrochemical response of encapsulated protein is influenced by the terminal groups of the silica pores. Cyt c does not present electrochemical response in conventional silica (hydroxyl terminated) or phenyl terminated silica. Direct electron transfer to encapsulated cytochrome c and ITO electrodes only takes place when the protein is encapsulated in methyl modified silica networks.

Chemical composition and solubility of ocean phosphatized rocks in seawater

In order to elucidate possibility of limestone phosphatization during contact with seawater two sets of experiments were carried out: that of solubility of natural phosphates in seawater and that of deposition of phosphorus onto calcareous phase. Concentration of phosphorus in seawater used for solubility experiments varied from 39 to 338 µ/l, temperature was 5.5-17.5°C and pH 7.8-7.9. The lowest solubility was characteristic of ancient crystallized samples. The deposition experiments showed that in case when concentration of dissolved phosphate in seawater reaches 3 mg/l it might be sorbed on solid CaCO3 phase without forming its own mineral. The latter is able to form rapidly but only if magnesium is not present in solution. In magnesium-free water calcium phosphates precipitate when concentration of dissolved phosphorus is higher than 0.9-1.2 mg/l. These results show that phosphatization of limestones in marine environment takes place during their contact with pore water but not with marine bottom water.

Isotopic composition of carbonates from the Logachev Hydrothermal Field, MAR 14°45'N

We investigate the Logatchev Hydrothermal Field at the Mid-Atlantic Ridge, 14°45' N to constrain the calcium isotope hydrothermal flux into the ocean. During the transformation of seawater to a hydrothermal solution, the Ca concentration of pristine seawater ([Ca]_SW) increases from about 10 mM to about 32 mM in the hydrothermal fluid endmember ([Ca]_HydEnd) and thereby adopts a d44/40Ca_HydEnd of -0.95+/-0.07 per mil relative to seawater (SW) and a 87Sr/86Sr isotope ratio of 0.7034(4). We demonstrate that d44/40Ca_HydEnd is higher than that of the bedrock at the Logatchev field. From mass balance calculations, we deduce a d44/40Ca of -1.17+/-0.04 per mil (SW) for the host-rocks in the reaction zone and -1.45+/-0.05 per mil (SW) for the isotopic composition of the entire hydrothermal cell of the Logatchev field. The values are isotopically lighter than the currently assumed d44/40Ca for Bulk Earth of -0.92+/-0.18 per mil (SW) [Skulan J., DePaolo D. J. and Owens T. L. (1997) Biological control of calcium isotopic abundances in the global calcium cycle. Geochim. Cosmochim. Acta 61,(12) 2505-2510] and challenge previous assumptions of no Ca isotope fractionation between hydrothermal fluid and the oceanic crust [Zhu P. and Macdougall J. D. (1998) Calcium isotopes in the marine environment and the oceanic calcium cycle. Geochim. Cosmochim. Acta 62,(10) 1691-1698; Schmitt A. -D., Chabeaux F. and Stille P. (2003) The calcium riverine and hydrothermal isotopic fluxes and the oceanic calcium mass balance. Earth Planet. Sci. Lett. 6731, 1-16]. Here we propose that Ca isotope fractionation along the fluid flow pathway of the Logatchev field occurs during the precipitation of anhydrite. Two anhydrite samples from the Logatchev Hydrothermal Field show an average fractionation of about D44/40Ca = -0.5 per mil relative to their assumed parental solutions. Ca isotope ratios in aragonites from carbonate veins from ODP drill cores indicate aragonite precipitation directly from seawater at low temperatures with an average d44/40Ca of -1.54+/-0.08 per mil (SW). The relatively large fractionation between the aragonite precipitates and seawater in combination with their frequent abundance in weathered mafic and ultramafic rocks suggest a reconsideration of the marine Ca isotope budget, in particular with regard to ocean crust alteration.

Semi-analytical solution for nonlinear vibration of laminated FGM plates with geometric imperfections

This paper investigates the nonlinear vibration of imperfect shear deformable laminated rectangular plates comprising a homogeneous substrate and two layers of functionally graded materials (FGMs). A theoretical formulation based on Reddy's higher-order shear deformation plate theory is presented in terms of deflection, mid-plane rotations, and the stress function. A semi-analytical method, which makes use of the one-dimensional differential quadrature method, the Galerkin technique, and an iteration process, is used to obtain the vibration frequencies for plates with various boundary conditions. Material properties are assumed to be temperature-dependent. Special attention is given to the effects of sine type imperfection, localized imperfection, and global imperfection on linear and nonlinear vibration behavior. Numerical results are presented in both dimensionless tabular and graphical forms for laminated plates with graded silicon nitride/stainless steel layers. It is shown that the vibration frequencies are very much dependent on the vibration amplitude and the imperfection mode and its magnitude. While most of the imperfect laminated plates show the well-known hard-spring vibration, those with free edges can display soft-spring vibration behavior at certain imperfection levels. The influences of material composition, temperature-dependence of material properties and side-to-thickness ratio are also discussed. (C) 2004 Elsevier Ltd. All rights reserved.