Preparation of 9/65/35 PLZT thin films deposited by a dip-coating process

Crack-free polycrystalline PLZT (Pb,a)(Zr,Ti)O-3 thin films with the perovskite structure were prepared by dir-coating using the Pechinis process. Lead acetate, hydrated lanthanum carbonate, zirconium n-propoxide and titanium isopropoxide were used as raw materials. The viscosity of the solution was adjusted in the range of 20 to 56 cP and the films were deposited by a dip-coating process on silicon (100) as substrate. Solutions with ionic concentration of 0.1 and 0.2 M were used. Thin film deposition was accomplished by dipping the substrates in the solution with control of withdrawal speed from 5 to 20 mm/min. The thin films were thermally treated in two steps: at 300 degreesC amid 650 degreesC. The influence of withdrawal speed. viscosity, heating rate and ionic concentration on the morphology of PLZT thin film was discussed. (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Influence of different drying temperatures on the amount of essential oils and citral content in Cymbopogon citratus (DC) Stapf. - Poaceae

Studies were conducted to show the effect of different temperatures in the drying process on the amount and quality of essential oils of Cymbopogon citratus (DC) Stapf. Leaves were harvested in the experimental field of the Agronomical Sciences College, UNESP, Botucatu, SP, Brazil in September, 1996. Blades of the leaves were cut in small parts (about 1-1,5 cm length), dried for several days at 30°, 50°, 70° and 90°C, until establishment of the weights. In the following process a hydrodistillation, during 2.5 hours, by Clevenger apparatus, was subsidized to extract the essential oils. A higher amount of oil could clearly be collected with the lower drying temperatures, except at 30°C, affected by fungus growing. Aspergillus sp., Penicillium sp., Rhyzopus sp., Cladosporium sp., Trichoderma sp. and Alternaria sp. were observed in the leaves. The analysis of the oil by GC-MS showed the variation of citral concentration of the treatments (86,1 to 95,2%). The results proved it is worthwhile to spend more time and effort in the production process using longer times of careful drying.

Evaluation of the combined solar TiO2/photo-Fenton process using multivariate analysis

The effect of combining the photocatalytic processes using TiO 2 and the photo-Fenton reaction with Fe3+ or ferrioxalate as a source of Fe2+ was investigated in the degradation of 4-chlorophenol (4CP) and dichloroacetic acid (DCA) using solar irradiation. Multivariate analysis was used to evaluate the role of three variables: iron, H2O2 and TiO2 concentrations. The results show that TiO2 plays a minor role when compared to iron and H2O2 in the solar degradation of 4CP and DCA in the studied conditions. However, its presence can improve TOC removal when H2O2 is totally consumed. Iron and peroxide play major roles, especially when Fe(NO3)3 used in the degradation of 4CP. No significant synergistic effect was observed by the addition of TiO 2 in this process. On the other hand, synergistic effects were observed between FeOx and TiO2 and between H 2O2 and TiO2 in the degradation of DCA. © IWA Publishing 2004.

Anatomical study of the retroarticular process in dry human skulls

Introduction: The retroarticular process is a bony prominence formed by the thickening of the lateral border of the mandibular fossa, forming the posterior wall of the temporomandibular joint. Since little is known and discussed about the retroarticular process, our aim was to study its presence, shape and size, relating these findings to the shape of the skulls according to the horizontal cephalic index. Materials and Methods: We used 400 dry human skulls of the Institute of Science and Technology - UNESP Anatomy Laboratory. Each skull was classified in brachycranics, mesocranics or dolichocranics, and then positioned on a craneostat to measure the height of the retroarticular process from its lower extremity to the auriculo-orbital plane. The width was obtained by measuring the base of the process on its longer lateral axis. Results: The retroarticular process was found bilaterally in 397 skulls (99.25%). All the processes were classified into the following shapes: pyramidal (35.55%), tubercular (31.78%), mammilar (20.73%), crest-like (9.05%) and molar shape (2.89%); 254 skulls (63.50%) showed the same type of process at the right and left sides (Kappa=0.496, moderate agreement). The average height and width were 5.28 mm and 12.81 mm, respectively. Conclusion: The retroarticular process was found in almost all the skulls examined. There are no significant evidences about the relationship among the presence, shape and size of the retroarticular process and the shape of the skulls according to the horizontal cephalic index. However, our findings led us to infer that there would be a functional relationship between the process and the temporomandibular joint.

Shipping costs: a rising challenge to the region's competitive development

This issue of the FAL Bulletin examines the impact of shipping costs on the exports of five Latin American and Caribbean countries by analysing the difference between the unit value of goods at the port of origin and at the port of destination, in three of the region's main external markets.

Budding Process During the Organogenesis of the Ventral Prostatic Lobe in Mongolian Gerbil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Insights into the swelling process and drug release mechanisms from cross-linked pectin/high amylose starch matrices

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Saccharification of Brazilian sisal pulp: evaluating the impact of mercerization on non-hydrolyzed pulp and hydrolysis products

Cultivation of sisal, a plant with a short growth cycle, is highly productive in Brazil. This work is part of extensive research in which sisal is valued. In these studies, sisal fibers are used in the preparation of bio-based composites and in the derivatization of the pulp, including posterior preparation of films. This study aimed to examine the use of sisal pulp in the production of bioethanol, which can potentially be a high efficiency process because of the cellulose content of this fiber. A previous paper addressed the hydrolysis of sisal pulp using sulfuric acid as a catalyst. In the present study, the influence of the mercerization process on the acid hydrolysis of sisal pulp was evaluated. Mercerization was achieved in a 20% wt NaOH solution, and the cellulosic pulp was suspended and vigorously mixed for 1, 2 and 3 h, at 50 A degrees C. The previously characterized mercerized pulps were hydrolyzed (100 A degrees C, 30% H2SO4, v/v), and the results are compared with those obtained for unmercerized pulp (described in a companion paper). The starting sample was characterized by viscometry, alpha-cellulose content, crystallinity index and scanning electron microscopy. During the reactions, aliquots were withdrawn, and the liquor was analyzed by HPLC. The residual pulps (non-hydrolyzed) were also characterized by the techniques described for the initial sample. The results revealed that pretreatment decreases the polyoses content as well as causes a decrease of up to 23% in the crystallinity and up to 21% in the average molar mass of cellulose after 3 h of mercerization. The mercerization process proved to be very important to achieve the final target. Under the same reaction conditions (30% and 100 A degrees C, 6 h), the hydrolysis of mercerized pulp generated yields of up to 50% more glucose. The results of this paper will be compared with the results of subsequent studies obtained using other acids, and enzymes, as catalysts.

Effect of humidity and solvent vapor phase on cellulose esters films

In the present study the effect of relative humidity (RH) during spin-coating process on the structural characteristics of cellulose acetate (CA), cellulose acetate phthalate (C-A-P), cellulose acetate butyrate (CAB) and carboxymethyl cellulose acetate butyrate (CMCAB) films was investigated by means of atomic force microscopy (AFM), ellipsometry and contact angle measurements. All polymer solutions were prepared in tetrahydrofuran (THF), which is a good solvent for all cellulose esters, and used for spin-coating at RH of (35 +/- A 5)%, (55 +/- A 5)% or (75 +/- A 5)%. The structural features were correlated with the molecular characteristics of each cellulose ester and with the balance between surface energies of water and THF and interface energy between water and THF. CA, CAB, CMCAB and C-A-P films spin-coated at RH of (55 +/- A 5)% were exposed to THF vapor during 3, 6, 9, 60 and 720 min. The structural changes on the cellulose esters films due to THF vapor exposition were monitored by means of AFM and ellipsometry. THF vapor enabled the mobility of cellulose esters chains, causing considerable changes in the film morphology. In the case of CA films, which are thermodynamically unstable, dewetting was observed after 6 min exposure to THF vapor. On the other hand, porous structures observed for C-A-P, CAB and CMCAB turned smooth and homogeneous after only 3 min exposure to THF vapor.

Influence of transportation methods and pre-slaughter rest periods on cortisol level in lambs

This study aimed to verify the influence of the transport in open or closed compartments (0 h), followed by two resting periods (1 and 3 h) for the slaughter process on the levels of cortisol as a indicative of stress level. At the slaughterhouse, blood samples were taken from 86 lambs after the transport and before slaughter for plasma cortisol analysis. The method of transport influenced in the cortisol concentration (0 h; P < 0.01). The animals transported in the closed compartment had a lower level (28.97 ng ml(-1)) than the animals transported in the open compartment (35.49 ng ml(-1)). After the resting period in the slaughterhouse. there was a decline in the plasmatic cortisol concentration, with the animals subjected to 3 h of rest presenting the lower average cortisol value (24.14 ng ml(-1); P < 0.05) than animals subjected to 1 h of rest (29.95 ng ml(-1)). It can be inferred that the lambs that remained 3 h in standby before slaughter had more time to recover from the stress of the transportation than those that waited just 1 h. Visual access to the external environment during the transport of the lambs is a stressful factor changing the level of plasmatic cortisol, and the resting period before slaughter was effective in lowering stress, reducing the plasmatic cortisol in the lambs. (c) 2012 Elsevier B.V. All rights reserved.

New Approaches for the Ethanol Oxidation Reaction of Pt/C on Carbon Cloth Using ATR-FTIR

This work describes the study of the ethanol oxidation reaction of a Pt/C Etek electrocatalyst that was supported on different substrates, such as gold, glassy carbon and carbon cloth treated with PTFE. In the ethanol oxidation reaction, the activity varies with the substrate, as well as the pathways for ethanol oxidation, as studied by an ATR-FTIR in situ setup using the carbon cloth as the electrocatalyst support. The electrocatalyst Pt/C supported on gold starts acetaldehyde production from ethanol oxidation at an onset potential of 0.1 V less than that observed for the same process on Teflon-treated carbon cloth. The Pt/C supported on the carbon cloth starts its CO2 production for the same oxidation process at 0.2 V less than on the Pt/C supported on gold substrate. The differences in catalytic activity for the ethanol oxidation reaction depend not only on the electrocatalyst but also on various electrode factors, such as the substrate, the roughness of the electrode and the charge transfer resistance.

The influence of nonverbal language on mediation

[ES]Mediation is a process that assigns meaning through the discourse of the disputants whereby signals that are verbally sent become rare indicators to dig for full communication. If reading nonverbal language was not taken into account, we would lose approximately 93% of the total information conveyed by someone; for this reason, it is necessary to know the most recurrent gestures to, thus, foster mediators’ communication skills in order to substantially improve their discourse and understanding. This paper focuses on arguing why nonverbal language is crucial for the mediation process on the basis of the analysis of the theoretical framework of the matter and its implications for mediation.

Can decision making in general surgery be based on evidence? An empirical study of Cochrane Reviews

BACKGROUND: This empirical study analyzes the current status of Cochrane Reviews (CRs) and their strength of recommendation for evidence-based decision making in the field of general surgery. METHODS: Systematic literature search of the Cochrane Database of Systematic Reviews and the Cochrane Collaboration's homepage to identify available CRs on surgical topics. Quantitative and qualitative characteristics, utilization, and formulated treatment recommendations were evaluated by 2 independent reviewers. Association of review characteristics with treatment recommendation was analyzed using univariate and multivariate logistic regression models. RESULTS: Ninety-three CRs, including 1,403 primary studies and 246,473 patients, were identified. Mean number of included primary studies per CR was 15.1 (standard deviation [SD] 14.5) including 2,650 (SD 3,340) study patients. Two and a half (SD 8.3) nonrandomized trials were included per analyzed CR. Seventy-two (77%) CRs were published or updated in 2005 or later. Explicit treatment recommendations were given in 45 (48%). Presence of a treatment recommendation was associated with the number of included primary studies and the proportion of randomized studies. Utilization of surgical CRs remained low and showed large inter-country differences. The most surgical CRs were accessed in UK, USA, and Australia, followed by several Western and Eastern European countries. CONCLUSION: Only a minority of available CRs address surgical questions and their current usage is low. Instead of unsystematically increasing the number of surgical CRs it would be far more efficient to focus the review process on relevant surgical questions. Prioritization of CRs needs valid methods which should be developed by the scientific surgical community.

Metodología para maximizar la rentabilidad de una terminal marítima de contenedores a través de la optimización de su grado de automatización

Son generalmente aceptadas las tendencias actuales de maximización de la automatización para la adaptación de las terminales marítimas de contenedores a las cada vez mayores exigencias competitivas del negocio de transporte de contenedores. En esta investigación, se somete a consideración dichas tendencias a través de un análisis que tenga en cuenta la realidad global de la terminal pero también su propia realidad local que le permita aprovechar sus fortalezas y minimizar sus debilidades en un mercado continuamente en crecimiento y cambio. Para lo cual se ha desarrollado un modelo de análisis en el que se tengan en cuenta los parámetros técnicos, operativos, económicos y financieros que influyen en el diseño de una terminal marítima de contenedores, desde su concepción como ente dependiente para generar negocio, todos ellos dentro de un perímetro definido por el mercado del tráfico de contenedores así como las limitaciones físicas introducidas por la propia terminal. Para la obtención de dicho modelo ha sido necesario llevar a cabo un proceso de estudio del contexto actual del tráfico de contenedores y su relación con el diseño de las terminales marítimas, así como de las metodologías propuestas hasta ahora por los diferentes autores para abordar el proceso de dimensionamiento y diseño de la terminal. Una vez definido el modelo que ha de servir de base para el diseño de una terminal marítima de contenedores desde un planteamiento multicriterio, se analiza la influencia de las diversas variables explicativas de dicho modelo y se cuantifica su impacto en los resultados económicos, financieros y operativos de la terminal. Un paso siguiente consiste en definir un modelo simplificado que vincule la rentabilidad de una concesión de terminal con el tráfico esperado en función del grado de automatización y del tipo de terminal. Esta investigación es el fruto del objetivo ambicioso de aportar una metodología que defina la opción óptima de diseño de una terminal marítima de contenedores apoyada en los pilares de la optimización del grado de automatización y de la maximización de la rentabilidad del negocio que en ella se desarrolla. It is generally accepted current trends in automation to maximize the adaptation of maritime container terminals to the growing competitive demands of the business of container shipping. In this research, is submitted to these trends through an analysis taking into account the global reality of the terminal but also their own local reality it could exploit its strengths and minimize their weaknesses in a market continuously growing and changing. For which we have developed a model analysis that takes into account the technical, operational, financial and economic influence in the design of a container shipping terminal, from its conception as being dependent to generate business, all within a perimeter defined by the market of container traffic and the physical constraints introduced by the terminal. To obtain this model has been necessary to conduct a study process in the current context of container traffic and its relation to the design of marine terminals, as well as the methodologies proposed so far by different authors to address the process sizing and design of the terminal. Having defined the model that will serve as the basis for the design for a container shipping terminal from a multi-criteria approach, we analyze the influence of various explanatory variables of the model and quantify their impact on economic performance, financial and operational of the terminal. A next step is to define a simplified model that links the profitability of a terminal concession with traffic expected on the basis of the degree of automation and the kind of terminal. This research is the result of the ambitious target of providing a methodology to define the optimal choice of designing a container shipping terminal on the pillars of automation optimizing and maximizing the profitability of the business that it develops.

Study of the effect of different hole sizes on mechanical strength of wafers for back contact solar cells

Drilling process on wafers to produce EWT or MWT solar cells is a critical fabrication step, which affects on their mechanical stability. The amount of damage introduced during drilling process depends on the density of holes, their size and the chemical process applied afterwards. To quantify the relation between size of the holes and reduction of mechanical strength, several sets of wafers have been prepared, with different hole diameter. The mechanical strength of these sets has been measured by the ring on ring bending test, and the stress state in the moment of failure has been deduced by FE simulation.