Sonic to ultrasonic Q of sandstones and limestones: Laboratory measurements at in situ pressures

Laboratory measurements of the attenuation and velocity dispersion of compressional and shear waves at appropriate frequencies, pressures, and temperatures can aid interpretation of seismic and well-log surveys as well as indicate absorption mechanisms in rocks. Construction and calibration of resonant-bar equipment was used to measure velocities and attenuations of standing shear and extensional waves in copper-jacketed right cylinders of rocks (30 cm in length, 2.54 cm in diameter) in the sonic frequency range and at differential pressures up to 65 MPa. We also measured ultrasonic velocities and attenuations of compressional and shear waves in 50-mm-diameter samples of the rocks at identical pressures. Extensional-mode velocities determined from the resonant bar are systematically too low, yielding unreliable Poisson's ratios. Poisson's ratios determined from the ultrasonic data are frequency corrected and used to calculate the sonic-frequency compressional-wave velocities and attenuations from the shear- and extensional-mode data. We calculate the bulk-modulus loss. The accuracies of attenuation data (expressed as 1000/Q, where Q is the quality factor) are +/- 1 for compressional and shear waves at ultrasonic frequency, +/- 1 for shear waves, and +/- 3 for compressional waves at sonic frequency. Example sonic-frequency data show that the energy absorption in a limestone is small (Q(P) greater than 200 and stress independent) and is primarily due to poroelasticity, whereas that in the two sandstones is variable in magnitude (Q(P) ranges from less than 50 to greater than 300, at reservoir pressures) and arises from a combination of poroelasticity and viscoelasticity. A graph of compressional-wave attenuation versus compressional-wave velocity at reservoir pressures differentiates high-permeability (> 100 mD, 9.87 X 10(-14) m(2)) brine-saturated sandstones from low-permeability (< 100 mD, 9.87 X 10 (14) m(2)) sandstones and shales.

Middle and Late Cenomanian anoxia in shallow and deeper shelf environments of western Morocco

The response of shallow-water sequences to oceanic anoxic event 2 and mid-Cenomanian events 1a and 1b was investigated along the west African margin of Morocco north of Agadir (Azazoul) and correlated with the deep-water sequence of the Tarfaya Basin (Mohammed Beach) based on biostratigraphy, mineralogy, phosphorus and stable isotopes. In the deeper Mohammed Beach section results show double peaks in δ13Corg for mid-Cenomanian events 1a and 1b (Rotalipora reicheli biozone, lower CC10a biozone), the characteristic oceanic anoxic event 2 δ13C excursion (Rotalipora cushmani extinction, top of CC10a biozone) and laminated (anoxic) black shale. In the shallow environment north of Agadir, a fluctuating sea-level associated with dysoxic, brackish and mesotrophic conditions prevailed during the middle to late Cenomanian, as indicated by oyster biostromes, nannofossils, planktonic and benthonic foraminiferal assemblages. Anoxic conditions characteristic of oceanic anoxic event 2 (for example, laminated black shales) did not reach into shallow-water environments until the maximum transgression of the early Turonian. Climate conditions decoupled along the western margin of Morocco between mid-Cenomanian event 1b and the Cenomanian–Turonian boundary, as also observed in eastern Tethys. North of Agadir alternating humid and dry seasonal conditions prevailed, whereas in the Tarfaya Basin the climate was dry and seasonal. This climatic decoupling can be attributed to variations in the Intertropical Convergence Zone and in the intensity of the north-east trade winds in tropical areas.

Paleomagnetism of the Santa Fe Group, central Brazil: Implications for the late Paleozoic apparent polar wander path for South America

Paleomagnetic and rockmagnetic data are reported for the Floresta Formation (Santa Fe Group) of the Sanfranciscana Basin, central Brazil. This formation represents the Permo-Carboniferous glacial record of the basin and comprises the Brocoto (diamictites and flow diamictites), Brejo do Arroz (red sandstones and shales with dropstones and invertebrate trails), and Lavado (red sandstones) members, which crop out near the cities of Santa Fe de Minas and Canabrava, Minas Gerais State. Both Brejo do Arroz and Lavado members were sampled in the vicinities of the two localities. Alternating field and thermal demagnetizations of 268 samples from 76 sites revealed reversed components of magnetization in all samples in accordance with the Permo-Carboniferous Reversed Superchron. The magnetic carriers are magnetite and hematite with both minerals exhibiting the same magnetization component, suggesting a primary origin for the remanence. We use the high-quality paleomagnetic pole for the Santa Fe Group (330.9 degrees E 65.7 degrees S; N = 60; alpha(95) = 4.1 degrees; k = 21) in a revised late Carboniferous to early Triassic apparent polar wander path for South America. On the basis of this result it is shown that an early Permian Pangea A-type fit is possible if better determined paleomagnetic poles become available.

Structural analysis of the Itapucumi Group in the Vallemi region, northern Paraguay: Evidence of a new Brasiliano/Pan-African mobile belt

The Neoproterozoic (Ediacaran) Itapucumi Group in northern Paraguay is composed of carbonate and siliciclastic rocks, including ooid grainstones, marls, shales and sandstones, containing Cloudina fossils in the eastern region. It is almost undeformed over the Rio Apa Cratonic Block but shows a strong deformational pattern at its western edge. A detailed structural analysis of the Itapucumi Group was conducted in the Vallemi Mine, along with a regional survey in other outcrops downstream in the Paraguay River and in the San Alfredo, Cerro Paiva and Sargent Jose E. Lopez regions. In the main Vallemi quarry, the structural style is characterized by an axial-plane slaty cleavage in open to isoclinal folds, sometimes overturned, associated with N-S trending thrust faults and shear zones of E-vergence and with a low-grade chlorite zone metamorphism. The structural data presented here are compatible with the hypothesis of a newly recognized mobile belt on the western side of the Rio Apa Cratonic Block, with opposite vergence to that of the Paraguay Mobile Belt in Brazil. Both belts are related to the Late Brasiliano/Pan-African tectonic cycle with a Lower Cambrian deformation and metamorphism age. The deformation could be due to the late collision of the Amazonian Craton with the remainder of Western Gondwana or to the western active plate boundary related to the Pampean Belt. The structural and lithologic differences between the western Itapucumi Group in the Vallemi and Paraguay River region and the eastern region, near San Alfredo and Cerro Paiva, suggest that this group could be divided into two lithostratigraphic units, but more stratigraphic and geochronological analyses are required to confirm this possibility. (C) 2010 Elsevier Ltd. All rights reserved.

Contribuição ao estudo petrográfico e geoquímico dos carvões da jazida de Chico Lomã Santo Antônio da Patrulha

São apresentados os resultados dos estudos petrográfico e geoquímico dos carvões da jazida de Chico Lomã, localizada no município de Santo Antônio da Patrulha, no nordeste do Rio Grande da Sul, situada entre as jazidas de Morungava (limite oeste) e Santa Terezinha (limite leste). Na sondagem estudada - 02-TG-88-RS - foram identificadas 7 camadas e 5 leitos de carvão. Entre estes, apenas as camadas E e F apresentam suficiente extensão lateral para serem consideradas economicamente exploráveis. Os carvões são ricos em matéria mineral, constituída, principalmente, de argila. O grupo maceral mais freqüente é o da vitrinita. No que diz respeito aos microlitotipos, ocorre, em geral, o predomínio de carbominerita. Foram identificadas 3 associações de microlitotipos, determinando a existência das seguintes faciologias: ambiente telmático (predomínio de vitrita-clarita), limo-telmático (predomínio de carbargilita-vitrita) e límnico (predomínio de carbargilita-durita-trimacerita). Os carvões apresentam rank que varia de betuminoso alto volátil C/sub-betuminoso A a betuminoso alto volátil A (ASTM). A utilização tecnológica dos carvões das camadas E e F, na siderurgia, pode ser sugerida, mesmo considerando-se seu elevado teor em cinza, desde que sejam submetidos a processos de beneficiamento. Em relação aos argilo-minerais, constatou-se a presença de caolinita, aparentemente relacionada ao conteúdo da matéria orgânica, e do interestratificado ilita-montmorilonita, provavelmente de origem detrítica. Foram identificados 3 grupos de elementos traços : associados à fração orgânica (Co, Ge, Ni, V e Zr), elementos intermediários (Cr, Cu e Sr) e associados à fração inorgânica (B, Ba e Ga). Observou-se, também, que os elementos do primeiro grupo, de maneira geral, se enriquecem nos litotipos com maior conteúdo de vitrênio, ao contrário dos elementos do último grupo que tendem a se enriquecer no carvão fosco e nos folhelhos. Os estudos realizados indicam um paleoambiente de água doce, no qual, provavelmente, tenham ocorrido pequenas ingressões marinhas entre as fases de formação de turfa.

An investigation of pile diameter influence in the bearing capacity on Dynamic Load Test (DLT)

During the construction of five residential buildings in the city of Taubate, State of São Paulo, it was possible to carry out one comprehensive investigation of the behavior of precast concrete piles in clay shales. This paper describes the results of Dynamic Load Tests (DLT's) executed in three piles with different diameters and with the same embedded length. The tests were monitored using the PDA(R) (Pile Driving Analyzer) and the pile top displacement was measured by pencil and paper procedure. From the curves of RMX versus DMX resulted from CASE(R) method, CAPWAPC(R) analyses were made for signals where the maximum mobilized soil resistance was verified. The results were compared with the predicted bearing capacity using the semi-empirical method of Decourt & Quaresma (1978) and Decourt (1982) based on SPT values and the description of the soil profile. Some comments related to the values of quake and damping used for clay shales in the analyses are also presented.

Avaliação das condições química e física dos sedimentos do estuário Jundiaí-Potengi

The aim of this study was to quantify the presence of major and minor elements in the sediments of the Jundiaí-Potengi estuary, bordering the municipalities of Macaíba, Natal and São Gonçalo do Amarante in the state of Rio Grande do Norte, Brazil, considering the evidence of anthropic activity along this estuary, resulting in pollution by treated and untreated wastewaters as well as those produced by industry and shrimp farming. The assessment of the environmental status of this estuary was based on physical-chemical parameters, such as granulometry, organic matter and the major (Al, Fe, Mn and P) and minor (Cd, Cr, Cu, Ni, Pb and Zn) elements found in sediment samples. Two collections were made at 12 georeferenced points along the channel of the estuary at different times. Granulometric analysis was carried out and the percentage of organic matter was determined. The sediments were microwave digested using acid digestion and quantitative analyses of the elements Al, Fe, Cd, Cr, Cu, Mn, Ni, P, Pb and Zn were performed by inductively coupled plasma optical emission spectrometry. Sediment analysis followed the methodology proposed by US EPA 3051A for total elements analysis. The small correlation between the organic matter and the elements studied here suggests that they are of geochemical rather than anthropic origin. The analytical results obtained from the bottom sediment samples in the study area show that the concentration of elements was below the reference values for standard shales (Turekian & Wedepohl, 1961) at the vast majority of points analyzed, ruling out a possible contamination by metals

Evolução tectono-estrutural do Campo de Xaréu (Sub-bacia de Mundaú, Bacia do Ceará - NE do Brasil: abordagem multiescala e pluriferramental

The Xaréu Oil Field, located in the center-southern portion of the Mundaú Sub-Basin (eastern portion of the Ceará Basin), is characterized by a main Iramework of NW-trending and NE-dipping faults. The faults in the Xaréu Oil Field, among which the Xaréu Fautt stands out, are arranged according to an extensional-listriclan, rooted on a detachment surface corresponding to the Mundaú Fault, the border fautt of Mundaú Sub-Basin. During the tectonic-structural evolution of the Xaréu Oil Field and the Mundaú Sub-Basin, the Mundaú Fault played a crucial role on the control of the geometry of both compartments. The main carbonatic unit in the Xaréu Oil Field, named the Trairí Member(Paracuru Formation of Late Aptian to Early Albian age), contains the largest oil volume in the field, concentrated in structurally-controlled accumulations. The Trairí Member is composed by a variety of carbonatic rocks (massive, bedded or laminated calcilutites, ostracodites, calcarenites and carbonatic rudites, all of them presenting variable degrees of dolomitization). The carbonatic rocks are interbedded into thick packages of black shales and marls, besides local beds of siliciclastic conglomerates, sandstones, siltnes and argillites. From the spatial association and the genetic relationships between the carbonatic and siliciclastic units, it is possible to group them in three lithofacies associations (Marginal Plain, Ramp and Lacustrine Interior) that, together, were developed in a lacustrine system associated to a marginal sabkha. Structural studies based on drill coresthat sample the Trairí Member in the Xaréu Oil Field allowed to characterize two generations of meso- to microscale structures: the D1 group presents a typical hydroplastic character, being characterized by intra/interstratal to oblique-bedding shear zones. The hydroplastic character related to these structures allowed to infer their development at an early-lithilication stage of the Trairí Member, leading to infer an Early Cretaceous age to them. The second group of structures identified in the drill cores, nominated D2 and ascribed to a Neogene age, presents a strictly brttle character, being typilied by normal faults and slickenfibers of re-crystallized clayminerals, ali olthem displaying variable orientations. Although the present faults in the Xaréu Oil Field (and, consequently, in the Mundaú Sub-Basin) were classically relerred as struetures of essentially normal displacement, the kinematics analysis of the meso-to microscaie D1 struetures in the drill cores led to deline oblique displacements (normal with a clockwise strike-slip component) to these faults, indicating a main tectonic transport to ENE. These oblique movements would be responsible for the installation of a transtensive context in the Mundaú Sub-Basin, as part of the transcurrent to translormant opening of the Atlantic Equatorial Margin. The balancing of four struetural cross-sections ofthe Xaréu Oil Field indicates that the Mundaú Fault was responsible for more than 50% of the total stretching (ß factor) registered during the Early Aptian. At the initial stages of the "rifting", during Early Aptianuntil the Holocene, the Mundaú Sub-Basin (and consequently the Xaréu Oil Fleld) accumulated a total stretching between 1.21 and 1.23; in other words, the crust in this segment of the Atlantic Equatorial Margin was subjeeted to an elongation of about 20%. From estimates of oblique displacements related to the faults, it ws possible to construct diagrams that allow the determination of stretching factors related to these displacements. Using these diagrams and assuming the sense 01 dominant teetonictransport towards ENE, it was possible to calculate the real stretching lactors related to the oblique movement 0 of the faults in the Mundaú Sub-Basin. which reached actual values between 1.28 and 1.42. ln addnion to the tectonic-structural studies in the Xaréu Oil Field, the interpretation of remote sensing products, coupled wnh characterization of terrain analogues in seleeted areas along the northern Ceará State (continental margins of the Ceará and Potiguar basins), provided addnional data and constraints about the teetonic-structural evolution of the oil lield. The work at the analogue sites was particularly effective in the recognition and mapping, in semidetail scale, several generations of struetures originated under a brittle regime. Ali the obtained information (from the Xaréu Oil Field, the remote sensor data and the terrain analogues) were jointly interpreted, culminating with the proposnion of an evolutionary model lor this segment of the Atlantic Equatorial Margin; this model that can be applied to the whole Margin, as well. This segmentof the Atlantic Equatorial Margin was delormedin an early E-W (when considered lhe present-day position of the South American Plate) transcurrent to transform regime with dextral kinematics, started Irom, at least, the Early Aptian, which left its record in several outcrops along the continental margin of the Ceará State and specilically in the Xaréu off Field. The continuous operation of the regime, through the Albian and later periods, led to the definitive separation between the South American and African plates, with the formation of oceanic lithosphere between the two continental blocks, due to the emplacement off spreading centers. This process involved the subsequent transition of the transcurrent to a translorm dextral regime, creating lhe Equatorial Atlantic Oceano With the separation between the South American and African plates already completed and the increasing separation between lhe continental masses, other tecton ic mechanisms began to act during the Cenozoic (even though the Cretaceous tectonic regime lasted until the Neogene), like an E-W compressive stress líeld (related to the spreading olthe oceanic floor along lhe M id-Atlantic Ridge and to the compression of the Andean Chain) effective Irom the Late Cretaceous, and a state of general extension olthe horizontal surface (due to the thermal uplift ofthe central portion of Borborema Province), effective during the Neogene. The overlap of these mechanisms during the Cenozoic led to the imprint of a complex tectonic framework, which apparently influenced the migration and entrapment 01 hydrocarbon in the Ceará Basin

Geologia, Geocronologia, Geoquímica e Petrogênese das Rochas Ígneas Cretácicas da Província Magmática do Cabo e suas Relações com as Unidades Sedimentares da Bacia de Pernambuco (NE do Brasil)

The area studied forms a thin NNE-directed belt situated south of Recife town (Pernambuco state), northeastern Brazil. Geologically, it comprises the Pernambuco Basin (PB), which is limited by the Pernambuco Lineament to the north, the Maragogi high to the south and the Pernambuco Alagoas massif to the west, all of them with Precambrian age. This thesis reports the results obtained for the Cabo Magmatic Province (CMP), aiming the characterization of the geology, stratigraphy, geochronology, geochemistry and petrogenesis of the Cretaceous igneous rocks presented in the PB. The PB is composed of the Cabo Formation (rift phase) at the base (polymictic conglomerates, sandstones, shales), an intermediate unit, the Estiva Formation (marbles and argillites), and, at the top, the Algodoais Formation (monomictic conglomerates, sandstones, shales). The CMP is represented by trachytes, rhyolites, pyroclastics (ignimbrites), basalts / trachy-andesites, monzonites and alkali-feldspar granite, which occur as dykes, flows, sills, laccoliths and plugs. Field observations and well descriptions show that the majority of the magmatic rocks have intrusive contacts with the Cabo Formation, although some occurrences are also suggestive of synchronism between volcanism and siliciclastic sedimentation. 40Ar/39Ar and zircon fission tracks for the magmatic rocks indicate an average age of 102 r 1 Ma for the CMP. This age represents an expressive event in the province and is detected in all igneous dated materials. It is considered as a minimum age (Albian) for the magmatic episode and the peak of the rift phase in the PB. The 40Ar/39Ar dates are about 10-14 Ma younger than published palynologic ages for this basin. Geochemically, the CMP may be divided in two major groups; i) a transitional to alkaline suite, constituted by basalts to trachy-andesites (types with fine-grained textures and phenocrysts of sanidine and plagioclase), trachytes (porphyrytic texture, with phenocrysts of sanidine and plagioclase) and monzonites; ii) a alkaline suite, highly fractionated, acidic volcano-plutonic association, formed by four subtypes (pyroclastic flows ignimbrites, fine-to medium-grained rhyolites, a high level granite, and later rhyolites). These four types are distinguished essentially by field aspects and petrographic and textural features. Compatible versus incompatible trace element concentrations and geochemical modeling based on both major and trace elements suggest the evolution through low pressure fractional crystallization for trachytes and other acidic rocks, whereas basalts / trachy-andesites and monzonites evolved by partial melting from a mantle source. Sr and Nd isotopes reveal two distinct sources for the rocks of the CMP. Concerning the acidic ones, the high initial Sr ratios (ISr = 0.7064-1.2295) and the negative HNd (-0.43 to -3.67) indicate a crustal source with mesoproterozoic model ages (TDM from 0.92 to 1.04 Ga). On the other hand, the basic to intermediate rocks have low ISr (0.7031-0.7042) and positive HNd (+1.28 to +1.98), which requires the depleted mantle as the most probable source; their model ages are in the range 0.61-0.66 Ga. However, the light rare earth enrichment of these rocks and partial melting modeling point to an incompatible-enriched lherzolitic mantle with very low quantity of garnet (1-3%). This apparent difference between geochemical and Nd isotopes may be resolved by assuming that the metasomatizing agent did not obliterate the original isotopic characteristics of the magmas. A 2 to 5% partial melting of this mantle at approximately 14 kbar and 1269oC account very well the basalts and trachy-andesites studied. By using these pressure and temperatures estimates for the generation of the basaltic to trachy-andesitic magma, it is determined a lithospheric stretching (E) of 2.5. This E value is an appropriated estimate for the sub-crustal stretching (astenospheric or the base of the lithosphere?) region under the Pernambuco Basin, the crustal stretching probably being lower. The integration of all data obtained in this thesis permits to interpret the magmatic evolution of the PB as follows; 1st) the partial melting of a garnet-bearing lherzolite generates incompatible-enriched basaltic, trachy-andesitic and monzonitic magmas; 2nd) the underplating of these basaltic magmas at the base of the continental crust triggers the partial melting of this crust, and thus originating the acidic magmas; 3rd) concomitantly with the previous stage, trachytic magmas were produced by fractionation from a monzonitic to trachy-andesitic liquid; 4th) the emplacement of the several magmas in superficial (e.g. flows) or sub-superficial (e.g. dykes, sills, domes, laccoliths) depths was almost synchronically, at about 102 r 1 Ma, and usually crosscutting the sedimentary rocks of the Cabo Formation. The presence of garnet in the lherzolitic mantle does not agree with pressures of about 14 kbar for the generation of the basaltic magma, as calculated based on chemical parameters. This can be resolved by admitting the astenospheric uplifting under the rift, which would place deep and hot material (mantle plume?) at sub-crustal depths. The generation of the magmas and their subsequent emplacement would be coupled with the crustal rifting of the PB, the border (NNE-SSW directed) and transfer (NW-SE directed) faults serving as conduits for the magma emplacement. Based on the E parameter and the integration of 40Ar/39Ar and palynologic data it is interpreted a maximum duration of 10-14 Ma for the rift phase (Cabo Formation clastic sedimentation and basic to acidic magmatism) of the PB

Análises estratigráfica e estrutural da Seção Rifte (Valanginiano ao Barremiano) na área do levantamento sísmico 3D de baixo vermelho, Bacia Potiguar emersa

Baixo Vermelho area, situated on the northern portion of Umbuzeiro Graben (onshore Potiguar Basin), represents a typical example of a rift basin, characterized, in subsurface, by the sedimentary rift sequence, correlated to Pendência Formation (Valanginian-Barremian), and by the Carnaubais fault system. In this context, two main goals, the stratigraphic and the structural analysis, had guided the research. For this purpose, it was used the 3D seismic volume and eight wells located in the study area and adjacencies. The stratigraphic analysis of the Valanginian-Barremian interval was carried through in two distinct phases, 1D and 2D, in which the basic concepts of the sequence stratigraphy had been adapted. In these phases, the individual analysis of each well and the correlation between them, allowed to recognize the main lithofacies, to interpret the effective depositional systems and to identify the genetic units and key-surfaces of chronostratigraphic character. The analyzed lithofacies are represented predominantly by conglomerates, sandstones, siltites and shales, with carbonate rocks and marls occurring subordinately. According to these lithofacies associations, it is possible to interpret the following depositional systems: alluvial fan, fluvio-deltaic and lacustrine depositional systems. The alluvial fan system is mainly composed by conglomerates deposits, which had developed, preferentially in the south portion of the area, being directly associated to Carnaubais fault system. The fluvial-deltaic system, in turn, was mainly developed in the northwest portion of the area, at the flexural edge, being characterized by coarse sandstones with shales and siltites intercalated. On the other hand, the lacustrine system, the most dominant one in the study area, is formed mainly by shales that could occur intercalated with thin layers of fine to very fine sandstones, interpreted as turbidite deposits. The recognized sequence stratigraphy units in the wells are represented by parasequence sets, systems tracts and depositional sequences. The parasequence sets, which are progradational or retrogradational, had been grouped and related to the systems tracts. The predominance of the progradation parasequence sets (general trend with coarsening-upward) characterizes the Regressive Systems Tract, while the occurrence, more frequently, of the retrogradation parasequence sets (general trend with finning-upward) represents the Transgressive System Tract. In the seismic stratigraphic analysis, the lithofacies described in the wells had been related to chaotic, progradational and parallel/subparallel seismic facies, which are associated, frequently, to the alluvial fans, fluvial-deltaic and lacustrine depositional systems, respectively. In this analysis, it was possible to recognize fifteen seismic horizons that correspond to sequence boundaries and to maximum flooding surfaces, which separates Transgressive to Regressive systems tracts. The recognition of transgressive-regressive cycles allowed to identify nine, possibly, 3a order deposicional sequences, related to the tectonic-sedimentary cycles. The structural analysis, in turn, was done at Baixo Vermelho seismic volume, which shows, clearly, the structural complexity printed in the area, mainly related to Carnaubais fault system, acting as an important fault system of the rift edge. This fault system is characterized by a main arrangement of normal faults with trend NE-SO, where Carnaubais Fault represents the maximum expression of these lineations. Carnaubais Fault corresponds to a fault with typically listric geometry, with general trend N70°E, dipping to northwest. It is observed, throughout all the seismic volume, with variations in its surface, which had conditioned, in its evolutive stages, the formation of innumerable structural features that normally are identified in Pendencia Formation. In this unit, part of these features is related to the formation of longitudinal foldings (rollover structures and distentional folding associated), originated by the displacement of the main fault plan, propitiating variations in geometry and thickness of the adjacent layers, which had been deposited at the same time. Other structural features are related to the secondary faultings, which could be synthetic or antithetic to Carnaubais Fault. In a general way, these faults have limited lateral continuity, with listric planar format and, apparently, they play the role of the accomodation of the distentional deformation printed in the area. Thus, the interaction between the stratigraphic and structural analysis, based on an excellent quality of the used data, allowed to get one better agreement on the tectonicsedimentary evolution of the Valanginian-Barremian interval (Pendência Formation) in the studied area

Arquitetura, litofácies e evolução tectonoestratigráfica da bacia do rio do peixe, nordeste do Brasil

The Rio do Peixe Basin is located in the border of Paraíba and Ceará states, immediately to the north of the Patos shear zone, encompassing an area of 1,315 km2. This is one of the main basins of eocretaceous age in Northeast Brazil, associated to the rifting event that shaped the present continental margin. The basin can be divided into four sub-basins, corresponding to Pombal, Sousa, Brejo das Freiras and Icozinho half-grabens. This dissertation was based on the analysis and interpretation of remote sensing products, field stratigraphic and structural data, and seismic sections and gravity data. Field work detailed the lithofacies characterization of the three formations previously recognised in the basin, Antenor Navarro, Sousa and Rio Piranhas. Unlike the classical vertical stacking, field relations and seismostratigraphic analysis highlighted the interdigitation and lateral equivalency between these units. On bio/chrono-stratigraphic and tectonic grounds, they correlate with the Rift Tectonosequence of neocomian age. The Antenor Navarro Formation rests overlies the crystalline basement in non conformity. It comprises lithofacies originated by a braided fluvial system system, dominated by immature, coarse and conglomeratic sandstones, and polymict conglomerates at the base. Its exposures occur in the different halfgrabens, along its flexural margins. Paleocurrent data indicate source areas in the basement to the north/NW, or input along strike ramps. The Sousa Formation is composed by fine-grained sandstones, siltites and reddish, locally grey-greenish to reddish laminated shales presenting wavy marks, mudcracks and, sometimes, carbonate beds. This formation shows major influence of a fluvial, floodplain system, with seismostratigraphic evidence of lacustrine facies at subsurface. Its distribution occupies the central part of the Sousa and Brejo das Freiras half-grabens, which constitute the main depocenters of the basin. Paleocurrent analysis shows that sediment transport was also from north/NW to south/SE

Análise da deformação pós-Rifte na Bacia do Araripe, Nordeste do Brasil

The Araripe Basin is located over Precambrian terrains of the Borborema Province, being part of Northeast Brazil inner basins. Its origin is related to the fragmentation of the Gondwana supercontinent and consequently opening of South Atlantic during early Cretaceous. The basin has a sedimentary infill encompassing four distinct evolution stages, comprising Paleozoic syneclisis, pre-rift, rift and post-rift. The target of this study comprises the post-rift section of the basin focusing deformational styles which affect evaporates from Ipubi Member of the Santana Formation, which is composed by gypsum and anidrite layers interbedded with shales. These units occur widespread across the basin. In the central part of the basin, near Nova Olinda-Santana do Cariri, evaporites are affected by an essentialy brittle deformation tipified by fibrous gypsum filled fractures, cutting massive layers of gypsum and anidrite. Veins with variable orientations and dips are observed in the region distributed over three main populations: i) a dominant NWSE with shallow to moderate NE dipping population, consisting of gypsum filled veins in which fibers are normal to vein walls; i) NE-SW veins with moderate SE dips containing subhorizontal growth fibers; and iii) N-S veins with shallow E-W dips with fibers oblique to vein walls. In the west portion of the basin, near Trindade-Ipubi-Araripina towns, evaporate layers are dominantly constituted by gypsum/anidrite finely stratified, showing a minor density of veins. These layers are affected by a unique style of deformation, more ductile, typified by gentle to open horizontal normal folding with several tens of meters length and with double plunging NW-SE or NE-SW hinges, configuring domic features. In detail, gypsum/anidrite laminae are affected by metre to decimeter scale close to tight folding, usually kinked, with broken hinges, locally turning into box folds. Veins show NE-SW main directions with shallow NE dips, growth fibers are parallel to vein walls, constituting slickenfibers. This region is marked by faults that affect Araripina Formation with NW-SE, NE-SW and E-W directions. The main structural styles and general orientations of structures which affected the post-rift section of Araripe Basin yielded important kinematic information analysis which led us to infer a E-W to NE-SW extension direction to the northeastern part of the Basin, whereas in the southeastern part, extension occurred in N-S direction. Thus, it was possible to determine a regional kinematic setting, through this analysis, characterizing a NE-SW to ENE-WSW system for the post-rift section, which is compatible with the tension settings for the Sout American Plate since Albian. Local variations at the fluid pressure linked (or not) to sedimentary overload variation define local tension settings. This way, at the northeastern portion of the basin, the post-rift deformation was governed by a setting which σ 1 is sub-horizontal trending NE-SW and, σ 3 is sub-vertical, emphasizing a reverse fault situation. At the southwestern portion however there was characterized a strike slip fault setting, featuring σ 1 trending ENEWSW and σ3 trending NNW-SSE

Pirometamorfismo nos arenitos da Formação Açu, Bacia Potiguar, NE do Brasil

Pyrometamorphism results from conditions of high temperatures and very low pressures provoked by the intrusion of hypabyssal basic bodies into sedimentary or metassedimentary hosting rocks. The onshore portion of the Potiguar Basin in NE Brazil offers examples of this type of metamorphism nearby the contacts of Paleogene to Neogene plugs, sills and dikes of diabases and basalts crosscutting sandstones, siltstones and shales of the Açu Formation (Albian-Cenomanian). The thermal effects over these rocks are reflected on textures and minerals assemblages that characterize the sanidinite facies of metamorphism, often with partial melting of the feldspathic and mica-rich matrix. The liquid formed is potassic and peraluminous, with variably colored rhyolitic glass (colorless, yellow, brown) comprising microcrystals of tridymite, sanidine and clinoenstatite, besides residual detrital clasts of quartz and rarely zircon, staurolite and garnet. Lenses of shale intercalated within the sandstones display crystallites of Fe-cordierite (sekaninaite), mullite, sanidine, armalcolite (Fe-Ti oxide) and brown spinel. The rocks formed due to the thermal effect of the intrusions are called buchites for which two types are herein described: a light one derived from feldspathic sandstone and siltstone protoliths; and a dark one derived from black shale protoliths. Textures indicating partial melting and minerals such as sanidine, mullite, tridymite and armalcolite strongly demonstrate that during the intrusion of the basic bodies the temperature reached 1,000-1,150°C, and was followed by quenching. Cooling of the interstitial melts has as consequences the closure of pores and decrease of the permeability of the protolith, which varies from about 17-11% in the unaffected rocks to zero in the thermally modified types. Although observed only at contacts and over small distances, the number of basic intrusions hosted within the Potiguar Basin in both onshore and offshore portions leaves opened the possibility of important implications of the thermal effects over the hydrocarbon exploration in this area as well in other Cretaceous and Paleozoic basins in Brazil

Camadas de tempestito grosso (coarse grained storm beds): exemplos do Permiano da bacia do Paraná

Tempestitos grossos constituem camadas delgadas de conglomerado gradando a arenito, com estratificação cruzada seguida de laminação ondulada truncante a simétrica e de drape/flaser de siltito/folhelho. Cinco exemplos extraídos do Permiano da bacia do Paraná ilustram esse tipo de depósito: três deles são de rochas siliciclásticas, contendo bioclastos de bivalves e vertebrados (Formação Rio Bonito-Membro Triunfo e Formação Palermo), enquanto os outros dois são de rochas carbonática e fosfática (respectivamente, formações Teresina e Corumbataí do Grupo Passa Dois). O componente tracional da base do tempestito grosso apresenta-se como arenite quartzoso/lítico ou grainstone oolítico com cimento calcífero preenchendo poros (casos das formações Palermo e Teresina). em sua maioria, os tempestitos grossos constituem pavimentos transgressivos intercalados em folhelhos ou tempestitos finos (arenitos muito finos a folhelhos com estratificação ondulada truncante-hummocky). em outro caso, extraído de subsuperfície, o pavimento transgressivo ocorre na base de uma sucessão progradante de barra de plataforma. O tempestito grosso da Formação Teresina constitui um evento transgressivo sobreposto a depósitos de barra de plataforma.

AMS and grain shape fabric of the Late Palaeozoic diamictites of the Southeastern Paran Basin, Brazil

Diamictites interbedded with marine shales and turbidites onlap the eastern border of the Parana Basin (Southern Brazil). These poorly sorted sediments were deposited during the Permo-Carboniferous glaciation, and their matrix-supported clasts show no preferred orientation. These massive rocks have been studied using anisotropy of magnetic susceptibility (AMS) and grain shape fabric. Hysteresis loops and thermomagnetic measurements show that AMS depends mostly on the paramagnetic clays, but fine ferromagnetic particles also contribute to the anisotropy. The coarse silt to sand grain preferred orientation study supports the use of AMS in describing the diamictite fabric, at least regarding the orientation of the foliation. AMS and grain shape data reveal subhorizontal to weakly inclined magnetic and grain shape foliation parallel to the regional bedding. The magnetic lineations are normally scattered within the foliation plane in agreement with the oblate AMS ellipsoids found in these rocks. Both fabric patterns are consistent with deposition by subaqueous mudflows that were resedimented downslope, with elastic supply from continental sources. The off-vertical grain shape foliation poles suggest that the deposition of diamictites was controlled by the depocentre topography of the Rio do Sul sub-basin.