Localização de descargas parciais em transformadores de potência por meio de sensores piezelétricos de baixo custo e sistemas inteligentes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Economic analysis for oregano under irrigation considering economic risk factors

The oregano is a plant, rich in essential oil and very used as spice in the preparation of foods. The objective of this paper was to analyze the viability of irrigation for oregano in Presidente Prudente, São Paulo state, Brazil, including economic risk factors, their effect on irrigation total cost, as well as the different pumping kinds. The Monte Carlo simulation was utilized to study the economic factors: fixed cost, labor, maintenance, pumping and water. The use of irrigation for the oregano in the region of Presidente Prudente is indicated because of its economic feasibility and the reduced risks. The average values of the benefit/cost for all water depths tested were higher than 1, indicating viability. The use of irrigation promoted lower risks compared to the non irrigated crop. The micro irrigation system presented greater sensitivity to changes of prices of the equipment associated to the variation of the useful life of the system. The oregano selling price was the most important factor involved in annual net profit. The water cost was the factor of lesser influence on the total cost. Due to the characteristic of high drip irrigation frequency there was no difference between the tariffs based in use hour of electric energy classified as green and blue, which are characterized by applying different rates on the energy consumption and demand according to the hours of day and times of the year. For the studied region it was recommended drip irrigation water management of oregano with the daily application of 100% of pan evaporation Class A using electric motor with tariffs blue or green.

Impatto di rifaximina sul microbiota intestinale: selezione di bifidobatteri antibiotico resistenti

The ideal approach for the long term treatment of intestinal disorders, such as inflammatory bowel disease (IBD), is represented by a safe and well tolerated therapy able to reduce mucosal inflammation and maintain homeostasis of the intestinal microbiota. A combined therapy with antimicrobial agents, to reduce antigenic load, and immunomodulators, to ameliorate the dysregulated responses, followed by probiotic supplementation has been proposed. Because of the complementary mechanisms of action of antibiotics and probiotics, a combined therapeutic approach would give advantages in terms of enlargement of the antimicrobial spectrum, due to the barrier effect of probiotic bacteria, and limitation of some side effects of traditional chemiotherapy (i.e. indiscriminate decrease of aggressive and protective intestinal bacteria, altered absorption of nutrient elements, allergic and inflammatory reactions). Rifaximin (4-deoxy-4’-methylpyrido[1’,2’-1,2]imidazo[5,4-c]rifamycin SV) is a product of synthesis experiments designed to modify the parent compound, rifamycin, in order to achieve low gastrointestinal absorption while retaining good antibacterial activity. Both experimental and clinical pharmacology clearly show that this compound is a non systemic antibiotic with a broad spectrum of antibacterial action, covering Gram-positive and Gram-negative organisms, both aerobes and anaerobes. Being virtually non absorbed, its bioavailability within the gastrointestinal tract is rather high with intraluminal and faecal drug concentrations that largely exceed the MIC values observed in vitro against a wide range of pathogenic microorganisms. The gastrointestinal tract represents therefore the primary therapeutic target and gastrointestinal infections the main indication. The little value of rifaximin outside the enteric area minimizes both antimicrobial resistance and systemic adverse events. Fermented dairy products enriched with probiotic bacteria have developed into one of the most successful categories of functional foods. Probiotics are defined as “live microorganisms which, when administered in adequate amounts, confer a health benefit on the host” (FAO/WHO, 2002), and mainly include Lactobacillus and Bifidobacterium species. Probiotic bacteria exert a direct effect on the intestinal microbiota of the host and contribute to organoleptic, rheological and nutritional properties of food. Administration of pharmaceutical probiotic formula has been associated with therapeutic effects in treatment of diarrhoea, constipation, flatulence, enteropathogens colonization, gastroenteritis, hypercholesterolemia, IBD, such as ulcerative colitis (UC), Crohn’s disease, pouchitis and irritable bowel syndrome. Prerequisites for probiotics are to be effective and safe. The characteristics of an effective probiotic for gastrointestinal tract disorders are tolerance to upper gastrointestinal environment (resistance to digestion by enteric or pancreatic enzymes, gastric acid and bile), adhesion on intestinal surface to lengthen the retention time, ability to prevent the adherence, establishment and/or replication of pathogens, production of antimicrobial substances, degradation of toxic catabolites by bacterial detoxifying enzymatic activities, and modulation of the host immune responses. This study was carried out using a validated three-stage fermentative continuous system and it is aimed to investigate the effect of rifaximin on the colonic microbial flora of a healthy individual, in terms of bacterial composition and production of fermentative metabolic end products. Moreover, this is the first study that investigates in vitro the impact of the simultaneous administration of the antibiotic rifaximin and the probiotic B. lactis BI07 on the intestinal microbiota. Bacterial groups of interest were evaluated using culture-based methods and molecular culture-independent techniques (FISH, PCR-DGGE). Metabolic outputs in terms of SCFA profiles were determined by HPLC analysis. Collected data demonstrated that rifaximin as well as antibiotic and probiotic treatment did not change drastically the intestinal microflora, whereas bacteria belonging to Bifidobacterium and Lactobacillus significantly increase over the course of the treatment, suggesting a spontaneous upsurge of rifaximin resistance. These results are in agreement with a previous study, in which it has been demonstrated that rifaximin administration in patients with UC, affects the host with minor variations of the intestinal microflora, and that the microbiota is restored over a wash-out period. In particular, several Bifidobacterium rifaximin resistant mutants could be isolated during the antibiotic treatment, but they disappeared after the antibiotic suspension. Furthermore, bacteria belonging to Atopobium spp. and E. rectale/Clostridium cluster XIVa increased significantly after rifaximin and probiotic treatment. Atopobium genus and E. rectale/Clostridium cluster XIVa are saccharolytic, butyrate-producing bacteria, and for these characteristics they are widely considered health-promoting microorganisms. The absence of major variations in the intestinal microflora of a healthy individual and the significant increase in probiotic and health-promoting bacteria concentrations support the rationale of the administration of rifaximin as efficacious and non-dysbiosis promoting therapy and suggest the efficacy of an antibiotic/probiotic combined treatment in several gut pathologies, such as IBD. To assess the use of an antibiotic/probiotic combination for clinical management of intestinal disorders, genetic, proteomic and physiologic approaches were employed to elucidate molecular mechanisms determining rifaximin resistance in Bifidobacterium, and the expected interactions occurring in the gut between these bacteria and the drug. The ability of an antimicrobial agent to select resistance is a relevant factor that affects its usefulness and may diminish its useful life. Rifaximin resistance phenotype was easily acquired by all bifidobacteria analyzed [type strains of the most representative intestinal bifidobacterial species (B. infantis, B. breve, B. longum, B. adolescentis and B. bifidum) and three bifidobacteria included in a pharmaceutical probiotic preparation (B. lactis BI07, B. breve BBSF and B. longum BL04)] and persisted for more than 400 bacterial generations in the absence of selective pressure. Exclusion of any reversion phenomenon suggested two hypotheses: (i) stable and immobile genetic elements encode resistance; (ii) the drug moiety does not act as an inducer of the resistance phenotype, but enables selection of resistant mutants. Since point mutations in rpoB have been indicated as representing the principal factor determining rifampicin resistance in E. coli and M. tuberculosis, whether a similar mechanism also occurs in Bifidobacterium was verified. The analysis of a 129 bp rpoB core region of several wild-type and resistant bifidobacteria revealed five different types of miss-sense mutations in codons 513, 516, 522 and 529. Position 529 was a novel mutation site, not previously described, and position 522 appeared interesting for both the double point substitutions and the heterogeneous profile of nucleotide changes. The sequence heterogeneity of codon 522 in Bifidobacterium leads to hypothesize an indirect role of its encoded amino acid in the binding with the rifaximin moiety. These results demonstrated the chromosomal nature of rifaximin resistance in Bifidobacterium, minimizing risk factors for horizontal transmission of resistance elements between intestinal microbial species. Further proteomic and physiologic investigations were carried out using B. lactis BI07, component of a pharmaceutical probiotic preparation, as a model strain. The choice of this strain was determined based on the following elements: (i) B. lactis BI07 is able to survive and persist in the gut; (ii) a proteomic overview of this strain has been recently reported. The involvement of metabolic changes associated with rifaximin resistance was investigated by proteomic analysis performed with two-dimensional electrophoresis and mass spectrometry. Comparative proteomic mapping of BI07-wt and BI07-res revealed that most differences in protein expression patterns were genetically encoded rather than induced by antibiotic exposure. In particular, rifaximin resistance phenotype was characterized by increased expression levels of stress proteins. Overexpression of stress proteins was expected, as they represent a common non specific response by bacteria when stimulated by different shock conditions, including exposure to toxic agents like heavy metals, oxidants, acids, bile salts and antibiotics. Also, positive transcription regulators were found to be overexpressed in BI07-res, suggesting that bacteria could activate compensatory mechanisms to assist the transcription process in the presence of RNA polymerase inhibitors. Other differences in expression profiles were related to proteins involved in central metabolism; these modifications suggest metabolic disadvantages of resistant mutants in comparison with sensitive bifidobacteria in the gut environment, without selective pressure, explaining their disappearance from faeces of patients with UC after interruption of antibiotic treatment. The differences observed between BI07-wt e BI07-res proteomic patterns, as well as the high frequency of silent mutations reported for resistant mutants of Bifidobacterium could be the consequences of an increased mutation rate, mechanism which may lead to persistence of resistant bacteria in the population. However, the in vivo disappearance of resistant mutants in absence of selective pressure, allows excluding the upsurge of compensatory mutations without loss of resistance. Furthermore, the proteomic characterization of the resistant phenotype suggests that rifaximin resistance is associated with a reduced bacterial fitness in B. lactis BI07-res, supporting the hypothesis of a biological cost of antibiotic resistance in Bifidobacterium. The hypothesis of rifaximin inactivation by bacterial enzymatic activities was verified by using liquid chromatography coupled with tandem mass spectrometry. Neither chemical modifications nor degradation derivatives of the rifaximin moiety were detected. The exclusion of a biodegradation pattern for the drug was further supported by the quantitative recovery in BI07-res culture fractions of the total rifaximin amount (100 μg/ml) added to the culture medium. To confirm the main role of the mutation on the β chain of RNA polymerase in rifaximin resistance acquisition, transcription activity of crude enzymatic extracts of BI07-res cells was evaluated. Although the inhibition effects of rifaximin on in vitro transcription were definitely higher for BI07-wt than for BI07-res, a partial resistance of the mutated RNA polymerase at rifaximin concentrations > 10 μg/ml was supposed, on the basis of the calculated differences in inhibition percentages between BI07-wt and BI07-res. By considering the resistance of entire BI07-res cells to rifaximin concentrations > 100 μg/ml, supplementary resistance mechanisms may take place in vivo. A barrier for the rifaximin uptake in BI07-res cells was suggested in this study, on the basis of the major portion of the antibiotic found to be bound to the cellular pellet respect to the portion recovered in the cellular lysate. Related to this finding, a resistance mechanism involving changes of membrane permeability was supposed. A previous study supports this hypothesis, demonstrating the involvement of surface properties and permeability in natural resistance to rifampicin in mycobacteria, isolated from cases of human infection, which possessed a rifampicin-susceptible RNA polymerase. To understand the mechanism of membrane barrier, variations in percentage of saturated and unsaturated FAs and their methylation products in BI07-wt and BI07-res membranes were investigated. While saturated FAs confer rigidity to membrane and resistance to stress agents, such as antibiotics, a high level of lipid unsaturation is associated with high fluidity and susceptibility to stresses. Thus, the higher percentage of saturated FAs during the stationary phase of BI07-res could represent a defence mechanism of mutant cells to prevent the antibiotic uptake. Furthermore, the increase of CFAs such as dihydrosterculic acid during the stationary phase of BI07-res suggests that this CFA could be more suitable than its isomer lactobacillic acid to interact with and prevent the penetration of exogenous molecules including rifaximin. Finally, the impact of rifaximin on immune regulatory functions of the gut was evaluated. It has been suggested a potential anti-inflammatory effect of rifaximin, with reduced secretion of IFN-γ in a rodent model of colitis. Analogously, it has been reported a significant decrease in IL-8, MCP-1, MCP-3 e IL-10 levels in patients affected by pouchitis, treated with a combined therapy of rifaximin and ciprofloxacin. Since rifaximin enables in vivo and in vitro selection of Bifidobacterium resistant mutants with high frequency, the immunomodulation activities of rifaximin associated with a B. lactis resistant mutant were also taken into account. Data obtained from PBMC stimulation experiments suggest the following conclusions: (i) rifaximin does not exert any effect on production of IL-1β, IL-6 and IL-10, whereas it weakly stimulates production of TNF-α; (ii) B. lactis appears as a good inducer of IL-1β, IL-6 and TNF-α; (iii) combination of BI07-res and rifaximin exhibits a lower stimulation effect than BI07-res alone, especially for IL-6. These results confirm the potential anti-inflammatory effect of rifaximin, and are in agreement with several studies that report a transient pro-inflammatory response associated with probiotic administration. The understanding of the molecular factors determining rifaximin resistance in the genus Bifidobacterium assumes an applicative significance at pharmaceutical and medical level, as it represents the scientific basis to justify the simultaneous use of the antibiotic rifaximin and probiotic bifidobacteria in the clinical treatment of intestinal disorders.

Percutaneous closure of patent foramen ovale: safe and effective but underutilized.

With three recently published randomized trials on patent foramen ovale (PFO) closure, the concept of PFO closure to reduce recurrent strokes has been proven; however, PFO closure is currently only considered for secondary prevention. Given the potential devastating consequences of a PFO-related event, we advocate screening for and closure of a PFO for primary prevention in high-risk populations. Such populations include patients who are suffering from a disease that is associated with PFO (e.g., migraine) or patients with high-risk hobbies/professions (e.g., weight-lifters, frequent-flyers, and deep sea divers). Looking at young people with a remaining average life expectancy of 50 years, we have to close 2.4 PFOs to prevent one stroke. This should support a more proactive attitude toward PFO screening and closure.

Tecnologías de conservación por métodos combinados en pimiento, chaucha y berenjena

La tecnología de los métodos combinados permite reducir la intensidad del tratamiento térmico y mantener las propiedades organolépticas en el producto final, mediante una combinación de obstáculos que aseguran la estabilidad y seguridad microbiana. El objetivo de este trabajo fue aplicar dicha tecnología en la conservación de tres hortalizas: pimiento, chaucha y berenjena y analizar la calidad y vida útil de los productos obtenidos. La elaboración de las conservas se efectuó del siguiente modo: las hortalizas fueron cortadas y posteriormente escaldadas en solución de ácidos cítrico, láctico y acético. Terminada esta etapa se envasaron con la solución de relleno, constituida por los ácidos de la solución de escaldado con la adición de ácido ascórbico. Los análisis que se realizaron tanto en el material fresco como en los productos procesados fueron: humedad, pH, hidratos de carbono, lípidos, proteína, vitamina C, °Brix, actividad enzimática y acidez total. En los productos ya procesados se realizó el control microbiológico. Los resultados indican que la aplicación de los métodos combinados permite conservar los productos elaborados a temperatura ambiente y se mantiene su seguridad microbiológica.

Approach to the use of indicators for the assessment of the environmental level of construction products

The European construction industry is supposed to consume the 40% of the natural European resources and to generate the 40% of the European solid waste. Conscious of the great damage being suffered by the environment because of construction activity, this work tries to provide the building actors with a new tool to improve the current situation. The tool proposed is a model for the comprehensive evaluation of construction products by determining their environmental level. In this research, the environmental level of a construction product has been defined as its quality of accomplishing the construction requirements needed by causing the minimum ecological impact in its surrounding environment. This information allows building actors to choose suitable materials for building needs and also for the environment, mainly in the project stage or on the building site, contributing to improve the relationship between buildings and environment. For the assessment of the environmental level of construction products, five indicators have been identified regarding their global environmental impact through the product life cycle: CO2 emissions provoked during their production, volume and toxicity of waste generated on the building site, durability and recycling capacity after their useful life. Therefore, the less environmental impact one construction product produces, the higher environmental level performs. The model has been tested in 30 construction products that include environmental criteria in their description. The results obtained will be discussed in this article. Furthermore, this model can lay down guidelines for the selection of ecoefficient construction products and the design of new eco-competitive and eco-committed ones

The value of cultural assets. Maintenance Costs and economic sustainability at heritage

Under the 12th International Conference on Building Materials and Components is inserted this communication related to the field of management of those assets that constitute the Spanish Cultural Heritage and maintenance. This work is related to the field of management of those assets that constitute the Spanish Cultural Heritage which share an artistic or historical background. The conservation and maintenance become a social demand necessary for the preservation of public values, requiring the investment of necessary resources. The legal protection involves a number of obligations and rights to ensure the conservation and heritage protection. The duty of maintenance and upkeep exceeds the useful life the property that must endure more for their cultural value for its usability. The establishment of the necessary conditions to prevent deterioration and precise in order to fulfill its social function, seeking to prolong the life of the asset, preserving their physical integrity and its ability to convey the values protected. This obligation implies a substantial financial effort to the holder of the property, either public or private entity, addressing a problem of economic sustainability. Economic exploitation, with the aim of contributing to their well-maintained, is sometimes the best way to get resources. The work will include different lines of research with the following objectives. - Establishment of processes for assessing total costs over the building life cycle (LCC), during the planning stages or maintenance budgets to determine the most advantageous operating system. - Relationship between the value of property and maintenance costs, and establishing a sensitivity analysis.

Hyperespectral images for the evaluation of the quality of minimally processed vegetables (spinach)

The production of minimally processed vegetables and fruits is an emergent sector, however these processes reduce the useful life of the products. Main preservation techniques such cold storage and modified atmosphere are limited. New treatments are being applied (O3 , UV‐C radiation, biodegradable films…etc.). The sector precise of cheap and fast techniques to evaluate the general quality and the security of the processed products, that constitute a tool of aid to the decision in the implementation of new procedures of packaging and/or treatments. Objectives: To explore hyperspectral imaging for monitoring the evolution of minimally processed leafy vegetables during shelf‐life . To identify and classify deterioration rates of the leaves through Multivariate analysis techniques (PLS‐DA)

Use of a scrapped ship as a floating breakwater for shore protection

The purpose of this research is to assess the effectiveness of a ship used as a detached floating breakwater for coastal protection and forming salients of sand or tombolos. Floating breakwaters have been extensively used as port or coastal protection structures and display advantages in terms of construction and ecology, amongst others. However, the greatest problem these structures present is the limited range of wave heights and periods for which they are really effective. Furthermore, ships may be considered as floating structures which, used as breakwaters, would keep the advantages of floating breakwaters and would increase their range of applicability. The possibility of using ships at the conclusion of their useful life for this purpose would also involve greater economic and environmental advantages. Tests were carried out to assess the ship’s effectiveness as a detached floating breakwater using a scaled down physical model to determine the vessel’s transmission coefficient (Kt) as to regular waves with significant periods of 5 sec to 12 sec and significant wave heights of 1.5 m to 4 m at depths from 20 m to 35 m. The ship proves effective for waves up to 4 m significant height and significant periods up to 9 sec. Hanson and Kraus and Pilarzyk’s analytical models, which take transmission coefficients into account, were used to analyse the shore’s response to the breakwater protection. The results obtained show that salients form for waves with periods between 6 sec and 9 sec. It is also concluded that the depths tested are far different from the more usual shallow water involved in constructing detached breakwaters and the shore’s response is therefore scarce.

Securing implementations of feedback-shift-register-based ciphers using compiler optimizations and co-processors

Los algoritmos basados en registros de desplazamiento con realimentación (en inglés FSR) se han utilizado como generadores de flujos pseudoaleatorios en aplicaciones con recursos limitados como los sistemas de apertura sin llave. Se considera canal primario a aquel que se utiliza para realizar una transmisión de información. La aparición de los ataques de canal auxiliar (en inglés SCA), que explotan información filtrada inintencionadamente a través de canales laterales como el consumo, las emisiones electromagnéticas o el tiempo empleado, supone una grave amenaza para estas aplicaciones, dado que los dispositivos son accesibles por un atacante. El objetivo de esta tesis es proporcionar un conjunto de protecciones que se puedan aplicar de forma automática y que utilicen recursos ya disponibles, evitando un incremento sustancial en los costes y alargando la vida útil de aplicaciones que puedan estar desplegadas. Explotamos el paralelismo existente en algoritmos FSR, ya que sólo hay 1 bit de diferencia entre estados de rondas consecutivas. Realizamos aportaciones en tres niveles: a nivel de sistema, utilizando un coprocesador reconfigurable, a través del compilador y a nivel de bit, aprovechando los recursos disponibles en el procesador. Proponemos un marco de trabajo que nos permite evaluar implementaciones de un algoritmo incluyendo los efectos introducidos por el compilador considerando que el atacante es experto. En el campo de los ataques, hemos propuesto un nuevo ataque diferencial que se adapta mejor a las condiciones de las implementaciones software de FSR, en las que el consumo entre rondas es muy similar. SORU2 es un co-procesador vectorial reconfigurable propuesto para reducir el consumo energético en aplicaciones con paralelismo y basadas en el uso de bucles. Proponemos el uso de SORU2, además, para ejecutar algoritmos basados en FSR de forma segura. Al ser reconfigurable, no supone un sobrecoste en recursos, ya que no está dedicado en exclusiva al algoritmo de cifrado. Proponemos una configuración que ejecuta múltiples algoritmos de cifrado similares de forma simultánea, con distintas implementaciones y claves. A partir de una implementación sin protecciones, que demostramos que es completamente vulnerable ante SCA, obtenemos una implementación segura a los ataques que hemos realizado. A nivel de compilador, proponemos un mecanismo para evaluar los efectos de las secuencias de optimización del compilador sobre una implementación. El número de posibles secuencias de optimizaciones de compilador es extremadamente alto. El marco de trabajo propuesto incluye un algoritmo para la selección de las secuencias de optimización a considerar. Debido a que las optimizaciones del compilador transforman las implementaciones, se pueden generar automáticamente implementaciones diferentes combinamos para incrementar la seguridad ante SCA. Proponemos 2 mecanismos de aplicación de estas contramedidas, que aumentan la seguridad de la implementación original sin poder considerarse seguras. Finalmente hemos propuesto la ejecución paralela a nivel de bit del algoritmo en un procesador. Utilizamos la forma algebraica normal del algoritmo, que automáticamente se paraleliza. La implementación sobre el algoritmo evaluado mejora en rendimiento y evita que se filtre información por una ejecución dependiente de datos. Sin embargo, es más vulnerable ante ataques diferenciales que la implementación original. Proponemos una modificación del algoritmo para obtener una implementación segura, descartando parcialmente ejecuciones del algoritmo, de forma aleatoria. Esta implementación no introduce una sobrecarga en rendimiento comparada con las implementaciones originales. En definitiva, hemos propuesto varios mecanismos originales a distintos niveles para introducir aleatoridad en implementaciones de algoritmos FSR sin incrementar sustancialmente los recursos necesarios. ABSTRACT Feedback Shift Registers (FSR) have been traditionally used to implement pseudorandom sequence generators. These generators are used in Stream ciphers in systems with tight resource constraints, such as Remote Keyless Entry. When communicating electronic devices, the primary channel is the one used to transmit the information. Side-Channel Attack (SCA) use additional information leaking from the actual implementation, including power consumption, electromagnetic emissions or timing information. Side-Channel Attacks (SCA) are a serious threat to FSR-based applications, as an attacker usually has physical access to the devices. The main objective of this Ph.D. thesis is to provide a set of countermeasures that can be applied automatically using the available resources, avoiding a significant cost overhead and extending the useful life of deployed systems. If possible, we propose to take advantage of the inherent parallelism of FSR-based algorithms, as the state of a FSR differs from previous values only in 1-bit. We have contributed in three different levels: architecture (using a reconfigurable co-processor), using compiler optimizations, and at bit level, making the most of the resources available at the processor. We have developed a framework to evaluate implementations of an algorithm including the effects introduced by the compiler. We consider the presence of an expert attacker with great knowledge on the application and the device. Regarding SCA, we have presented a new differential SCA that performs better than traditional SCA on software FSR-based algorithms, where the leaked values are similar between rounds. SORU2 is a reconfigurable vector co-processor. It has been developed to reduce energy consumption in loop-based applications with parallelism. In addition, we propose its use for secure implementations of FSR-based algorithms. The cost overhead is discarded as the co-processor is not exclusively dedicated to the encryption algorithm. We present a co-processor configuration that executes multiple simultaneous encryptions, using different implementations and keys. From a basic implementation, which is proved to be vulnerable to SCA, we obtain an implementation where the SCA applied were unsuccessful. At compiler level, we use the framework to evaluate the effect of sequences of compiler optimization passes on a software implementation. There are many optimization passes available. The optimization sequences are combinations of the available passes. The amount of sequences is extremely high. The framework includes an algorithm for the selection of interesting sequences that require detailed evaluation. As existing compiler optimizations transform the software implementation, using different optimization sequences we can automatically generate different implementations. We propose to randomly switch between the generated implementations to increase the resistance against SCA.We propose two countermeasures. The results show that, although they increase the resistance against SCA, the resulting implementations are not secure. At bit level, we propose to exploit bit level parallelism of FSR-based implementations using pseudo bitslice implementation in a wireless node processor. The bitslice implementation is automatically obtained from the Algebraic Normal Form of the algorithm. The results show a performance improvement, avoiding timing information leakage, but increasing the vulnerability against differential SCA.We provide a secure version of the algorithm by randomly discarding part of the data obtained. The overhead in performance is negligible when compared to the original implementations. To summarize, we have proposed a set of original countermeasures at different levels that introduce randomness in FSR-based algorithms avoiding a heavy overhead on the resources required.

Estudio de las propiedades de las fábricas históricas de adobe como soporte a intervenciones de rehabilitación

El extenso legado edificado que constituyen las construcciones históricas de fábrica de adobe distribuidas por toda la península encuentra en la región de Aveiro (Portugal) su máxima expresión, tanto desde el punto de vista cuantitativo, un 30% de los edificios existentes en la región, como tipológico, compuesto por un amplio conjunto de diferentes construcciones (edificios residenciales, edificios militares, iglesias, escuelas, teatros, naves industriales, etc.), muchos de los cuales de reconocido valor histórico, arquitectónico y patrimonial. Tras la gradual desaparición del empleo de la fábrica de adobe como técnica constructiva, durante la segunda mitad del siglo XX, la necesaria conservación y/o rehabilitación de los edificios remanentes no se ha tenido en cuenta. Como consecuencia de esta actitud generalizada de pasividad continuada, se verifica el estado actual de deterioro y de daño acusado que presentan una gran parte de estas construcciones, del cual ha resultado el panorama presente de abandono y ruina en el que se encuentran muchas de ellas. Por regla general, la solución adoptada para afrontar el estado actual de los edificios en estas condiciones suele ser la demolición. No obstante lo anterior, en los últimos años, se viene produciendo en el seno de los diferentes agentes que intervienen en la toma de decisiones sobre estos edificios un interés creciente en su preservación, promoviendo la rehabilitación de los mismos. Empieza de este modo a cobrar importancia la necesidad de desarrollar estrategias de intervención que posibiliten alargar la vida útil de estas estructuras, permitiendo, por un lado, establecer metodologías de análisis de sus condiciones de seguridad, que posibiliten determinar las medidas de actuación necesarias para el aseguramiento de las mismas frente a las acciones existentes y, en su caso, a la incorporación de nuevas solicitaciones debidas a cambios de uso o ampliaciones, así como, dando respuesta a los principales mecanismo de daño a los que se encuentran sujetas. Tratándose de estructuras que fueron construidas utilizando técnicas y materiales escasamente estudiados y entre tanto abandonados, se hace también necesario, y con carácter previo a lo anterior, acometer un estudio e investigación multidisciplinares que permitan su caracterización y comprensión, y la par establecer un diagnóstico sobre los principales agentes y procesos patológicos que promueven el deterioro de las mismas. En este contexto, el estudio llevado a cabo tuvo como objetivos ampliar el conocimiento e investigación acerca de las propiedades y parámetros resistentes de las fábricas históricas de adobe, así como, analizar los principales mecanismos de daño asociados a las mismas, a la luz del el estado actual de estas construcciones, y su repercusión en el comportamiento resistente de las fábricas –con especial énfasis para la influencia del agua–. De este modo, se pretendió construir una base de resultados que, por un lado, pueda servir de soporte a intervenciones de rehabilitación y/o consolidación de estas estructuras – permitiendo de forma ágil y a partir de datos y recursos de cálculo expeditos la evaluación de los niveles de seguridad en las fábricas–, y por otro, el estudio de soluciones de mejora o corrección de deficiencias en su comportamiento estructural. The vast edified legacy composed of the historical adobe load-bearing walls which can be found spread all over the Iberian peninsula has, in the region of Aveiro (Portugal), its maximum expression, both from a quantitative point of view (around 30% of the local construction) and a typological point of view, including a considerable number of different types of constructions (residential buildings, military buildings, churches, industrial buildings, etc.), most of which have a recognized high historical, architectural and patrimonial value. The conservation and/or rehabilitation of many of these edifications has been neglected, since its gradual abandonment as constructive technique during the second half of the 20th century. As a consequence of this posture of general passivity, it is nowadays visible the state of pronounced damage manifested by great part of these constructions, which has been leading to their abandonment and state of ruin. In most cases, the option for demolition has been the solution found to face the actual state of these constructions. However, in recent years, a growing interest in the preservation and maintenance of the adobe constructions has become visible by the envolved parties, with the obvious consequence of rehabilitation. By so, it becomes mandatory to develop strategies of intervention that, through rehabilitation, are able to extend the useful life of the existing structures, allowing on one hand, to establish methodologies to analyze their safety state and determine the actions needed to ensure their protection against existing pressures and, when applicable, the occurrence of new demands due to changes of use or extensions, and on the other hand, to give response to the main damage mechanisms to which these structures are exposed. Because these structures were built using not very well know techniques and materials, which have been, in the meantime, abandoned, it is now crucial that these are object of a previous phase of study and multidisciplinary investigation, essential not only to their characterization and comprehension, but also to the diagnosis of the main pathological processes that affect them. In this context, the present study had as main goal to develop the analysis and knowledge regarding the properties and resistant parameters of the adobe masonry as well as bringing to the light of day the actual state of the existing adobe constructions, making evident the main damage mechanisms by which they are affected and analyzing, through their occurrence, the vulnerability of the mentioned properties and resistant parameters. By so, it was objective of the present study the development of a result database which on one hand, supports the execution of rehabilitation interventions and/or strengthening of these constructions and, on other hand, allows the development of improvement solutions in the mechanical characteristics of the adobe masonry which permit corrections of deficiencies in their structural behavior with a special emphasis on the influence of water. Thus, a database of results was developed. Its goal is, on one hand, to support the rehabilitation or consolidation interventions on these structures - allowing for a quick analysis of the safety state of the adobe walls from expedite data and calculus resources and, on the other hand, to study improvement or correction solutions of their structural behavior.

Sobre la forma de garantizar la trazabilidad metrológica en los sistemas hospitalarios

Dentro del equipamiento que existen en los hospitales, se realizan muy diversas actuaciones para el correcto funcionamiento de los equipos que se destinan, tanto a medir sobre el paciente o para tratamiento sobre estos mismos, el abanico de equipos que existen es muy grande, sin contar con los que directamente se instalan o, más correctamente, se implantan en el paciente. Los hospitales tienen establecidas pautas de mantenimiento tanto correctivo como preventivo, también de verificación relativa a seguridad y, en algunos casos, acciones que van destinadas a comprobar las magnitudes en los equipos. Esto último no es lo normal, de hecho, en muchos casos, la mayoría, se desconoce cómo poder comprobar que las magnitudes de un equipo se pueden trazar a un patrón de medida nacional. La investigación se ha desarrollado para determinar, siendo algo que esta patente hasta en la normalización ISO, que no existen para muchos equipos principios establecidos para garantizar la trazabilidad metrológica da las magnitudes físicas en las que trabaja durante su vida útil. Debido a la amplitud de este campo, el desarrollo de investigación se ha llevado en un formato piramidal, desde las necesidades para poder llegar a un estudio concreto de equipos concretos (Termómetros Clínicos, Tensiómetros, Ultrasonidos y Onda Corta). Para llegar a estos se ha realizado un estudio de cómo se encuentra la trazabilidad metrológica en todo el espectro, desde la gestión hasta llegar a casos particulares. Estudiando la gran cantidad de documentación existente y llegando a determinar el campo de trabajo en la metrología hospitalaria, clasificando los equipos y determinando como se encuentran definidos los métodos que llevan a realidad la trazabilidad metrológica, en la normalización. Un grupo no muy trabajado de los equipos electromédicos son los que se encuentran dentro de los tratamientos de Rehabilitación de traumatología, siendo equipos de uso muy habitual en los centros de salud para las lesiones musculares y óseas. A este asunto se ha dedicado un esfuerzo extra, con un reporte histórico de su origen y en qué punto se encuentran ahora. Se han estudiado dentro de estos equipos los de tratamiento de ultrasonidos, de diatermia y onda corta, que son los más representativos de los equipos destinados a electro terapia, pero hay que tener en cuenta que hay campos que se han mencionado globalmente de la rehabilitación, como son la terapia o la biomecánica, de forma similar a otras tecnologías sanitarias de otras especialidades (radiología o análisis clínico). Hay, también, dentro de la terapia, todos esos tratamientos propios de gimnasio, como son poleas, pesas, mesas de masajes, balones, etc… Que su metrología es sencilla, son equipos que existen medios de comprobación de las magnitudes que utilizan por la existencia en otras actividades de la industria (balanzas, pesas, etc). La investigación realizada ha pretendido evaluar todo el global y llegar a casos concretos para determinar cómo está la situación. Llegando a desarrollar una clasificación de equipos y de normas, que permiten vislumbrar las necesidades metrológicas y permitiría establecer una Gestión de la Trazabilidad Metrológica, concluyendo en el estudio para los equipos que se han mencionado. ABSTRACT Within the equipment that exist in the hospitals, there are very diverse performances for the correct operation of the equipment that is intended both to measure on the patient or for treatment on these same, the range of equipment available is very large, without which directly are installed or, more correctly, are implanted in the patient. The hospitals have established patterns of maintenance both corrective and preventive, also of verification of security and, in some cases, actions which are intended to check the magnitudes in the equipment. This last is not normal, in fact, in many cases, the majority, it is not known as to be able to check that the magnitudes of a computer can be traced to a pattern of national measure. The research has been developed to determine, is something that this patent up to the International Organization for Standardization (ISO), that do not exist for many teams established principles to ensure the metrological traceability gives the physical quantities in which they work during its useful life. Due to the breadth of this field, the development of research has been conducted in a pyramid format, from the needs to be able to reach a specific study of specific equipment (Clinical Thermometers, Tensiometers, Ultrasound, and Short Wave). To reach theme, has been carried out a study of how is the metrological traceability across the entire spectrum, from the management to individuals cases. Considering the large amount of existing documentation and arriving to determine the labor camp in the metrology hospital, sorting equipment and determining how are defined the methods that lead to reality the metrological traceability, in the standardization. A group not too worked for medical electrical equipment are found within the rehabilitation treatment of traumatology, being equipment of very common use in the health centers for muscle injuries and bone. In this matter has been dedicated an extra effort, with a report history of its origin and where they are now. We have studied within these teams about the treatment of ultrasound, diathermy, short wave, which are the most representative of the equipment that is destined to electro therapy, but it must be borne in mind that there are fields that have been mentioned globally of rehabilitation, as are the therapy or the biomechanics, similar to other health technologies from other specialties (radiology or clinical analysis). There is, also, within the therapy, all these treatments own gym, such as pulleys, weights, tables of massages, balls, etc… that its metrology is simple, are computers that there are means of verification of the magnitudes that used by the existence in other activities of the industry (scales, weights, etc). The research carried out has tried to assess the entire global and reach specific cases to determine the situation as it is. Arriving in the development of a classification of equipment and standards, which give us a glimpse of the metrological needs and establish a Management of the Metrological Traceability, concluding in the study for computers that have been mentioned.

Caracterización del hormigón en relación a la difusión de gases y su correlación con el radón

Radon gas (Rn) is a natural radioactive gas present in some soils and able to penetrate buildings through the building envelope in contact with the soil. Radon can accumulate within buildings and consequently be inhaled by their occupants. Because it is a radioactive gas, its disintegration process produces alpha particles that, in contact with the lung epithelia, can produce alterations potentially giving rise to cancer. Many international organizations related to health protection, such as WHO, confirm this causality. One way to avoid the accumulation of radon in buildings is to use the building envelope as a radon barrier. The extent to which concrete provides such a barrier is described by its radon diffusion coefficient (DRn), a parameter closely related to porosity (ɛ) and tortuosity factor (τ). The measurement of the radon diffusion coefficient presents challenges, due to the absence of standard procedures, the requirement to establish adequate airtightness in testing apparatus (referred to here as the diffusion cell), and due to the fact that measurement has to be carried out in an environment certified for use of radon calibrated sources. In addition to this calibrated radon sources are costly. The measurement of the diffusion coefficient for non-radioactive gas is less complex, but nevertheless retains a degree of difficulty due to the need to provide reliably airtight apparatus for all tests. Other parameters that can characterize and describe the process of gas transport through concrete include the permeability coefficient (K) and the electrical resistivity (ρe), both of which can be measured relatively easily with standardized procedure. The use of these parameters would simplify the characterization of concrete behaviour as a radon barrier. Although earlier studies exist, describing correlation among these parameters, there is, as has been observed in the literature, little common ground between the various research efforts. For precisely this reason, prior to any attempt to measure radon diffusion, it was deemed necessary to carry out further research in this area, as a foundation to the current work, to explore potential relationships among the following parameters: porosity-tortuosity, oxygen diffusion coefficient, permeability coefficient and resistivity. Permeability coefficient measurement (m2) presents a more straightforward challenge than diffusion coefficient measurement. Some authors identify a relationship between both coefficients, including Gaber (1988), who proposes: k= a•Dn Equation 1 Where: a=A/(8ΠD020), A = sample cross-section, D020 = diffusion coefficient in air (m2/s). Other studies (Klink et al. 1999, Gaber and Schlattner 1997, Gräf and Grube et al. 1986), experimentally relate both coefficients of different types of concrete confirming that this relationship exists, as represented by the simplified expression: k≈Dn Equation 2 In each particular study a different value for n was established, varying from 1.3 to 2.5, but this requires determination of a value for n in a more general way because these proposed models cannot estimate diffusion coefficient. If diffusion coefficient has to be measured to be able to establish n, these relationships are not interesting. The measurement of electric resistivity is easier than diffusion coefficient measurement. Correlation between the parameters can be established via Einstein´s law that relates movement of electrical charges to media conductivity according to the expression: D_e=k/ρ Equation 3 Where: De = diffusion coefficient (cm2/s), K = constant, ρ = electric resistivity (Ω•cm). The tortuosity factor is used to represent the uneven geometry of concrete pores, which are described as being not straight, but tortuous. This factor was first introduced in the literature to relate global porosity with fluid transport in a porous media, and can be formulated in a number of different ways. For example, it can take the form of equation 4 (Mason y Malinauskas), which combines molecular and Knudsen diffusion using the tortuosity factor: D=ε^τ (3/2r √(πM/8RT+1/D_0 ))^(-1) Equation 4 Where: r = medium radius obtained from MIP (µm), M = gas molecular mass, R = ideal gases constant, T = temperature (K), D0 = coefficient diffusion in the air (m2/s). Few studies provide any insight as to how to obtain the tortuosity factor. The work of Andrade (2012) is exceptional in this sense, as it outlines how the tortuosity factor can be deduced from pore size distribution (from MIP) from the equation: ∅_th=∅_0•ε^(-τ). Equation 5 Where: Øth = threshold diameter (µm), Ø0 = minimum diameter (µm), ɛ = global porosity, τ = tortuosity factor. Alternatively, the following equation may be used to obtain the tortuosity factor: DO2=D0*ɛτ Equation 6 Where: DO2 = oxygen diffusion coefficient obtained experimentally (m2/s), DO20 = oxygen diffusion coefficient in the air (m2/s). This equation has been inferred from Archie´s law ρ_e=〖a•ρ〗_0•ɛ^(-m) and from the Einstein law mentioned above, using the values of oxygen diffusion coefficient obtained experimentally. The principal objective of the current study was to establish correlations between the different parameters that characterize gas transport through concrete. The achievement of this goal will facilitate the assessment of the useful life of concrete, as well as open the door to the pro-active planning for the use of concrete as a radon barrier. Two further objectives were formulated within the current study: 1.- To develop a method for measurement of gas coefficient diffusion in concrete. 2.- To model an analytic estimation of radon diffusion coefficient from parameters related to concrete porosity and tortuosity factor. In order to assess the possible correlations, parameters have been measured using the standardized procedures or purpose-built in the laboratory for the study of equations 1, 2 y 3. To measure the gas diffusion coefficient, a diffusion cell was designed and manufactured, with the design evolving over several cycles of research, leading ultimately to a unit that is reliably air tight. The analytic estimation of the radon diffusion coefficient DRn in concrete is based on concrete global porosity (ɛ), whose values may be experimentally obtained from a mercury intrusion porosimetry test (MIP), and from its tortuosity factor (τ), derived using the relations expressed in equations 5 y 6. The conclusions of the study are: Several models based on regressions, for concrete with a relative humidity of 50%, have been proposed to obtain the diffusion coefficient following the equations K=Dn, K=a*Dn y D=n/ρe. The final of these three relations is the one with the determination coefficient closest to a value of 1: D=(19,997*LNɛ+59,354)/ρe Equation 7 The values of the obtained oxygen diffusion coefficient adjust quite well to those experimentally measured. The proposed method for the measurement of the gas coefficient diffusion is considered to be adequate. The values obtained for the oxygen diffusion coefficient are within the range of those proposed by the literature (10-7 a 10-8 m2/s), and are consistent with the other studied parameters. Tortuosity factors obtained using pore distribution and the expression Ø=Ø0*ɛ-τ are inferior to those from resistivity ρ=ρ0*ɛ-τ. The closest relationship to it is the one with porosity of pore diameter 1 µm (τ=2,07), being 7,21% inferior. Tortuosity factors obtained from the expression DO2=D0*ɛτ are similar to those from resistivity: for global tortuosity τ=2,26 and for the rest of porosities τ=0,7. Estimated radon diffusion coefficients are within the range of those consulted in literature (10-8 a 10-10 m2/s).ABSTRACT El gas radón (Rn) es un gas natural radioactivo presente en algunos terrenos que puede penetrar en los edificios a través de los cerramientos en contacto con el mismo. En los espacios interiores se puede acumular y ser inhalado por las personas. Al ser un gas radioactivo, en su proceso de desintegración emite partículas alfa que, al entrar en contacto con el epitelio pulmonar, pueden producir alteraciones del mismo causando cáncer. Muchos organismos internacionales relacionados con la protección de la salud, como es la OMS, confirman esta causalidad. Una de las formas de evitar que el radón penetre en los edificios es utilizando las propiedades de barrera frente al radón de su propia envolvente en contacto con el terreno. La principal característica del hormigón que confiere la propiedad de barrera frente al radón cuando conforma esta envolvente es su permeabilidad que se puede caracterizar mediante su coeficiente de difusión (DRn). El coeficiente de difusión de un gas en el hormigón es un parámetro que está muy relacionado con su porosidad (ɛ) y su tortuosidad (τ). La medida del coeficiente de difusión del radón resulta bastante complicada debido a que el procedimiento no está normalizado, a que es necesario asegurar una estanquidad a la celda de medida de la difusión y a que la medida tiene que ser realizada en un laboratorio cualificado para el uso de fuentes de radón calibradas, que además son muy caras. La medida del coeficiente de difusión de gases no radioactivos es menos compleja, pero sigue teniendo un alto grado de dificultad puesto que tampoco está normalizada, y se sigue teniendo el problema de lograr una estanqueidad adecuada de la celda de difusión. Otros parámetros que pueden caracterizar el proceso son el coeficiente de permeabilidad (K) y la resistividad eléctrica (ρe), que son más fáciles de determinar mediante ensayos que sí están normalizados. El uso de estos parámetros facilitaría la caracterización del hormigón como barrera frente al radón, pero aunque existen algunos estudios que proponen correlaciones entre estos parámetros, en general existe divergencias entre los investigadores, como se ha podido comprobar en la revisión bibliográfica realizada. Por ello, antes de tratar de medir la difusión del radón se ha considerado necesario realizar más estudios que puedan clarificar las posibles relaciones entre los parámetros: porosidad-tortuosidad, coeficiente de difusión del oxígeno, coeficiente de permeabilidad y resistividad. La medida del coeficiente de permeabilidad (m2) es más sencilla que el de difusión. Hay autores que relacionan el coeficiente de permeabilidad con el de difusión. Gaber (1988) propone la siguiente relación: k= a•Dn Ecuación 1 En donde: a=A/(8ΠD020), A = sección de la muestra, D020 = coeficiente de difusión en el aire (m2/s). Otros estudios (Klink et al. 1999, Gaber y Schlattner 1997, Gräf y Grube et al. 1986) relacionan de forma experimental los coeficientes de difusión de radón y de permeabilidad de distintos hormigones confirmando que existe una relación entre ambos parámetros, utilizando la expresión simplificada: k≈Dn Ecuación 2 En cada estudio concreto se han encontrado distintos valores para n que van desde 1,3 a 2,5 lo que lleva a la necesidad de determinar n porque no hay métodos que eviten la determinación del coeficiente de difusión. Si se mide la difusión ya deja de ser de interés la medida indirecta a través de la permeabilidad. La medida de la resistividad eléctrica es muchísimo más sencilla que la de la difusión. La relación entre ambos parámetros se puede establecer a través de una de las leyes de Einstein que relaciona el movimiento de cargas eléctricas con la conductividad del medio según la siguiente expresión: D_e=k/ρ_e Ecuación 3 En donde: De = coeficiente de difusión (cm2/s), K = constante, ρe = resistividad eléctrica (Ω•cm). El factor de tortuosidad es un factor de forma que representa la irregular geometría de los poros del hormigón, al no ser rectos sino tener una forma tortuosa. Este factor se introduce en la literatura para relacionar la porosidad total con el transporte de un fluido en un medio poroso y se puede formular de distintas formas. Por ejemplo se destaca la ecuación 4 (Mason y Malinauskas) que combina la difusión molecular y la de Knudsen utilizando el factor de tortuosidad: D=ε^τ (3/2r √(πM/8RT+1/D_0 ))^(-1) Ecuación 4 En donde: r = radio medio obtenido del MIP (µm), M = peso molecular del gas, R = constante de los gases ideales, T = temperatura (K), D0 = coeficiente de difusión de un gas en el aire (m2/s). No hay muchos estudios que proporcionen una forma de obtener este factor de tortuosidad. Destaca el estudio de Andrade (2012) en el que deduce el factor de tortuosidad de la distribución del tamaño de poros (curva de porosidad por intrusión de mercurio) a partir de la ecuación: ∅_th=∅_0•ε^(-τ) Ecuación 5 En donde: Øth = diámetro umbral (µm), Ø0 = diámetro mínimo (µm), ɛ = porosidad global, τ = factor de tortuosidad. Por otro lado, se podría utilizar también para obtener el factor de tortuosidad la relación: DO2=D0*-τ Ecuación 6 En donde: DO2 = coeficiente de difusión del oxígeno experimental (m2/s), DO20 = coeficiente de difusión del oxígeno en el aire (m2/s). Esta ecuación está inferida de la ley de Archie ρ_e=〖a•ρ〗_0•ɛ^(-m) y la de Einstein mencionada anteriormente, utilizando valores del coeficiente de difusión del oxígeno DO2 obtenidos experimentalmente. El objetivo fundamental de la tesis es encontrar correlaciones entre los distintos parámetros que caracterizan el transporte de gases a través del hormigón. La consecución de este objetivo facilitará la evaluación de la vida útil del hormigón así como otras posibilidades, como la evaluación del hormigón como elemento que pueda ser utilizado en la construcción de nuevos edificios como barrera frente al gas radón presente en el terreno. Se plantean también los siguientes objetivos parciales en la tesis: 1.- Elaborar una metodología para la medida del coeficiente de difusión de los gases en el hormigón. 2.- Plantear una estimación analítica del coeficiente de difusión del radón a partir de parámetros relacionados con su porosidad y su factor de tortuosidad. Para el estudio de las correlaciones posibles, se han medido los parámetros con los procedimientos normalizados o puestos a punto en el propio Instituto, y se han estudiado las reflejadas en las ecuaciones 1, 2 y 3. Para la medida del coeficiente de difusión de gases se ha fabricado una celda que ha exigido una gran variedad de detalles experimentales con el fin de hacerla estanca. Para la estimación analítica del coeficiente de difusión del radón DRn en el hormigón se ha partido de su porosidad global (ɛ), que se obtiene experimentalmente del ensayo de porosimetría por intrusión de mercurio (MIP), y de su factor de tortuosidad (τ), que se ha obtenido a partir de las relaciones reflejadas en las ecuaciones 5 y 6. Las principales conclusiones obtenidas son las siguientes: Se proponen modelos basados en regresiones, para un acondicionamiento con humedad relativa de 50%, para obtener el coeficiente de difusión del oxígeno según las relaciones: K=Dn, K=a*Dn y D=n/ρe. La propuesta para esta última relación es la que tiene un mejor ajuste con R2=0,999: D=(19,997*LNɛ+59,354)/ρe Ecuación 7 Los valores del coeficiente de difusión del oxígeno así estimados se ajustan a los obtenidos experimentalmente. Se considera adecuado el método propuesto de medida del coeficiente de difusión para gases. Los resultados obtenidos para el coeficiente de difusión del oxígeno se encuentran dentro del rango de los consultados en la literatura (10-7 a 10-8 m2/s) y son coherentes con el resto de parámetros estudiados. Los resultados de los factores de tortuosidad obtenidos de la relación Ø=Ø0*ɛ-τ son inferiores a la de la resistividad (ρ=ρ0*ɛ-τ). La relación que más se ajusta a ésta, siendo un 7,21% inferior, es la de la porosidad correspondiente al diámetro 1 µm con τ=2,07. Los resultados de los factores de tortuosidad obtenidos de la relación DO2=D0*ɛτ son similares a la de la resistividad: para la porosidad global τ=2,26 y para el resto de porosidades τ=0,7. Los coeficientes de difusión de radón estimados mediante estos factores de tortuosidad están dentro del rango de los consultados en la literatura (10-8 a 10-10 m2/s).

Construcción modular ligera energéticamente eficiente

Esta tesis trata sobre la construcción modular ligera, dentro del contexto de la eficiencia energética y de cara a los conceptos de nZEB (near Zero Energy Building) y NZEB (Net Zero Energy Building) que se manejan en el ámbito europeo y específicamente dentro del marco regulador de la Directiva 2010/31 UE. En el contexto de la Unión Europea, el sector de la edificación representa el 40% del total del consumo energético del continente. Asumiendo la necesidad de reducir este consumo se han planteado, desde los organismos de dirección europeos, unos objetivos (objetivos 20-20-20) para hacer más eficiente el parque edificatorio. Estos objetivos, que son vinculantes en términos de legislación, comprometen a todos los estados miembros a conseguir la meta de reducción de consumo y emisiones de GEI (Gases de Efecto Invernadero) antes del año 2020. Estos conceptos de construcción modular ligera (CML) y eficiencia energética no suelen estar asociados por el hecho de que este tipo de construcción no suele estar destinada a un uso intensivo y no cuenta con unos cerramientos con niveles de aislamiento de acuerdo a las normativas locales o códigos de edificación de cada país. El objetivo de nZEB o NZEB, e incluso Energy Plus, según sea el caso, necesariamente (y así queda establecido en las normativas), dependerá no sólo de la mejora de los niveles de aislamiento de los edificios, sino también de la implementación de sistemas de generación renovables, independientemente del tipo de sistema constructivo con el que se trabaje e incluso de la tipología edificatoria. Si bien es cierto que los niveles de industrialización de la sociedad tecnológica actual han alcanzado varias de las fases del proceso constructivo - sobre todo en cuanto a elementos compositivos de los edificios- también lo es el hecho de que las cotas de desarrollo conseguidas en el ámbito de la construcción no llegan al nivel de evolución que se puede apreciar en otros campos de las ingenierías como la aeronáutica o la industria del automóvil. Aunque desde finales del siglo pasado existen modelos y proyectos testimoniales de construcción industrializada ligera (CIL) e incluso ya a principios del siglo XX, ejemplos de construcción modular ligera (CML), como la Casa Voisin, la industrialización de la construcción de edificios no ha sido una constante progresiva con un nivel de comercialización equiparable al de la construcción masiva y pesada. Los términos construcción industrializada, construcción prefabricada, construcción modular y construcción ligera, no siempre hacen referencia a lo mismo y no siempre son sinónimos entre sí. Un edificio puede ser prefabricado y no ser modular ni ligero y tal es el caso, por poner un ejemplo, de la construcción con paneles de hormigón prefabricado. Lo que sí es una constante es que en el caso de la construcción modular ligera, la prefabricación y la industrialización, casi siempre vienen implícitas en muchos ejemplos históricos y actuales. Con relación al concepto de eficiencia energética (nZEB o incluso NZEB), el mismo no suele estar ligado a la construcción modular ligera y/o ligera industrializada; más bien se le ve unido a la idea de cerramientos masivos con gran inercia térmica propios de estándares de diseño como el Passivhaus; y aunque comúnmente a la construcción ligera se le asocian otros conceptos que le restan valor (corta vida útil; función y formas limitadas, fuera de todo orden estético; limitación en los niveles de confort, etc.), los avances que se van alcanzando en materia de tecnologías para el aprovechamiento de la energía y sistemas de generación renovables, pueden conseguir revertir estas ideas y unificar el criterio de eficiencia + construcción modular ligera. Prototipos y proyectos académicos– como el concurso Solar Decathlon que se celebra desde el año 2002 promovido por el DOE (Departamento de Energía de los Estados Unidos), y que cuenta con ediciones europeas como las de los años 2010 y 2012, replantean la idea de la construcción industrializada, modular y ligera dentro del contexto de la eficiencia energética, con prototipos de viviendas de ± 60m2, propuestos por las universidades concursantes, y cuyo objetivo es alcanzar y/o desarrollar el concepto de NZEB (Net Zero Energy Building) o edificio de energía cero. Esta opción constructiva no sólo representa durabilidad, seguridad y estética, sino también, rapidez en la fabricación y montaje, además de altas prestaciones energéticas como se ha podido demostrar en las sucesivas ediciones del Solar Decathlon. Este tipo de iniciativas de desarrollo de tecnologías constructivas, no sólo apuntan a la eficiencia energética sino al concepto global de energía neta, Energía plus o cero emisiones de CO2. El nivel de emisiones por la fabricación y puesta en obra de los materiales de construcción depende, en muchos casos, no solo de la propia naturaleza del material, sino también de la cantidad de recursos utilizados para producir una unidad de medida determinada (kg, m3, m2, ml, etc). En este sentido podría utilizarse, en muchos casos, el argumento válido de que a menos peso, y a menos tamaño, menos emisiones globales de gases de efecto invernadero y menos contaminación. Para el trabajo de investigación de esta tesis se han tomado como referencias válidas para estudio, prototipos tanto de CML (Modular 3D) como de CIL (panelizado y elementos 2D), dado que para los fines de análisis de las prestaciones energéticas de los materiales de cerramiento, ambos sistemas son equiparables. Para poder llegar a la conclusión fundamental de este trabajo de tesis doctoral - que consiste en demostrar la viabilidad tecnológica/ industrial que supone la combinación de la eficiencia energética y la construcción modular ligera - se parte del estudio del estado de la técnica ( desde la selección de los materiales y los posibles procesos de industrialización en fábrica, hasta su puesta en obra, funcionamiento y uso, bajo los conceptos de consumo cero, cero emisiones de carbono y plus energético). Además -y con un estado de la técnica que identifica la situación actual- se llevan a cabo pruebas y ensayos con un prototipo a escala natural y células de ensayo, para comprobar el comportamiento de los elementos compositivos de los mismos, frente a unas condicionantes climáticas determinadas. Este tipo de resultados se contrastan con los obtenidos mediante simulaciones informáticas basadas en los mismos parámetros y realizadas en su mayoría mediante métodos simplificados de cálculos, validados por los organismos competentes en materia de eficiencia energética en la edificación en España y de acuerdo a la normativa vigente. ABSTRACT This thesis discusses lightweight modular construction within the context of energy efficiency in nZEB (near Zero Energy Building) and NZEB (Net Zero Energy Building) both used in Europe and, specifically, within the limits of the regulatory framework of the EU Directive 2010/31. In the European Union the building sector represents 40% of the total energy consumption of the continent. Due to the need to reduce this consumption, European decision-making institutions have proposed aims (20-20-20 aims) to render building equipment more efficient. These aims are bound by law and oblige all member States to endeavour to reduce consumption and GEI emissions before the year 2020. Lightweight modular construction concepts and energy efficiency are not generally associated because this type of building is not normally meant for intensive use and does not have closures with insulation levels which fit the local regulations or building codes of each country. The objective of nZEB or NZEB and even Energy Plus, depending on each case, will necessarily be associated (as established in the guidelines) not only with the improvement of insulation levels in buildings, but also with the implementation of renewable systems of generation, independent of the type of building system used and of the building typology. Although it is true that the levels of industrialisation in the technological society today have reached several of the building process phases - particularly in the composite elements of buildings - it is also true that the quotas of development achieved in the area of construction have not reached the evolutionary levelfound in other fields of engineering, such as aeronautics or the automobile industry. Although there have been models and testimonial projects of lightweight industrialised building since the end of last century, even going back as far as the beginning of the XX century with examples of lightweight modular construction such as the Voisin House, industrialisation in the building industry has not been constant nor is its comercialisation comparable to massive and heavy construction. The terms industrialised building, prefabricated building, modular building and lightweight building, do not always refer to the same thing and they are not always synonymous. A building can be prefabricated yet not be modular or lightweight. To give an example, this is the case of building with prefabricated concrete panels. What is constant is that, in the case of lightweight modular construction, prefabrication and industrialisation are almost always implicit in many historical and contemporary examples. Energy efficiency (nZEB or even NZEB) is not normally linked to lightweight modular construction and/or industrialised lightweight; rather, it is united to the idea of massive closureswith high thermal inertia typical of design standards such as the Passive House; and although other concepts that subtract value from it are generally associated with lightweight building (short useful life, limited forms and function, inappropriate toany aesthetic pattern; limitation in comfort levels, etc.), the advances being achieved in technology for benefitting from energy and renewable systems of generation may well reverse these ideas and unify the criteria of efficiency + lightweight modular construction. Academic prototypes and projects - such as the Solar Decathlon competition organised by the US Department of Energy and celebrated since 2002, with its corresponding European events such as those held in 2010 and 2012, place a different slant on the idea of industrialised, modular and lightweight building within the context of energy efficiency, with prototypes of homes measuring approximately 60m2, proposed by university competitors, whose aim is to reach and/or develop the NZEB concept, or the zero energy building. This building option does not only signify durability, security and aesthetics, but also fast manufacture and assembly. It also has high energy benefits, as has been demonstrated in successive events of the Solar Decathlon. This type of initiative for the development of building technologies, does not only aim at energy efficiency, but also at the global concept of net energy, Energy Plus and zero CO2 emissions. The level of emissions in the manufacture and introduction of building materials in many cases depends not only on the inherent nature of the material, but also on the quantity of resources used to produce a specific unit of measurement (kg, m3, m2, ml, etc.). Thus in many cases itcould be validly arguedthat with less weight and smaller size, there will be fewer global emissions of greenhouse effect gases and less contamination. For the research carried out in this thesis prototypes such as the CML (3D Module) and CIL (panelled and elements) have been used as valid study references, becauseboth systems are comparablefor the purpose of analysing the energy benefits of closure materials. So as to reach a basic conclusion in this doctoral thesis - that sets out to demonstrate the technological/industrial viability of the combination of energy efficiency and lightweight modular construction - the departure point is the study of the state of the technique (from the selection of materials and the possible processes of industrialisation in manufacture, to their use on site, functioning and use, respecting the concepts of zero consumption, zero emissions of carbon and Energy Plus). Moreover, with the state of the technique identifying the current situation, tests and practices have been carried out with a natural scale prototype and test cells so as to verify the behaviour of the composite elements of these in certain climatic conditions. These types of result are contrasted with those obtained through computer simulation based on the same parameters and done, principally, using simplified methods of calculation, validated by institutions competent in energy efficiency in Spanish building and in line with the rules in force.

Avances tecnológicos y obsolescencia programada

El objetivo seguido en este proyecto fin de carrera, ha sido el análisis de la evolución general de la tecnología, tanto electrónica, como en Telecomunicaciones e Informática, desde sus inicios hasta la actualidad, realizando un estudio sobre cómo esos avances han mejorado, incluso cambiado nuestra vida cotidiana y cómo a consecuencia de la conversión de muchos de estos productos tecnológicos en objeto de consumo masivo, la propia dinámica económico-comercial ha llevado a las empresas a la programación del fin del su vida útil con el objeto de incrementar su demanda y, consiguientemente, la producción. Se trata de lo que se conoce desde hace décadas como Obsolescencia Programada. Para realizar este documento se ha realizado un breve repaso por los acontecimientos históricos que promovieron el inicio de esta práctica, así como también nos ha llevado a realizar mención de todos esos aparatos tecnológicos que han sufrido una mayor evolución y por tanto son los más propensos a que se instauren en ellos, debido a cómo influyen dichos cambios en los consumidores. Otro de los aspectos más importantes que rodean a la Obsolescencia Programada, es cómo influye en el comportamiento de la sociedad, creando en ella actitudes consumistas, que precisamente son las que alimentan que el ciclo económico siga basándose en incluir esta práctica desde el diseño del producto, puesto que a mayor consumo, mayor producción, y por tanto, supone un aumento de beneficios para el fabricante. Aunque, lo que para algunos supone un amplio margen de rentabilidad, existen otros componentes de la ecuación que no salen tan bien parados, como pueden ser los países del tercer mundo que están siendo poblados de basura electrónica, y en general el medio ambiente y los recursos de los que hoy disponemos, que no son ilimitados, y que están viéndose gravemente afectados por la inserción de esta práctica. Como cierre de este análisis, se repasarán algunas de las técnicas empleadas en algunos de los productos más utilizados hoy en día y las conclusiones a las que se han llevado después de analizar todos estos puntos del tema. ABSTRACT. The main goal followed in this final project has been analyzing the overall evolution of technology, both electronics and telecommunications. Also, computer science; from beginning to present it has been realized some studies about these advances have improved our daily life, even changing our routine, and turn us massive consumers of all technological products on the market. This dynamic economic and commercial has led companies to programming the end of its useful life in order to increase demand, and consequently, the production. This is known as Obsolescence. To make this document has been made a brief review through historical events that promoted the opening of this practice, and also led us to make mention all these technological devices have undergone further evolution and therefore more likely to establish them, because these changes affect consumers. Another important aspect around planned obsolescence is how to influence in society’s behavior, creating consumerist attitudes, which are precisely those feed the economic cycle continues to be based on including this practice from product design, because increased consumption and production. Therefore, this fact increases profits for the manufacturer. Although, for some people suppose a wide margin of profitability, there are other components do not have such luck; for example, third World countries have been filled with e-waste and the environment, in general, and resources available today which are not unlimited, and who are seriously affected by the inclusion of this practice. To close this analysis, we will review a few techniques used in some products most widely used today, and the conclusions that have been made after analyzing all these points of the topic.